| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Move the parts of romstage.c that populate the UPD-M data structure to
the newly created fsp_m_params.c file. Since
platform_fsp_memory_init_params_cb gets called from the FSP driver and
not directly from car_stage_entry the two code parts in romstage.c
weren't directly interacting. Since soc/romstage.h only contains the
mainboard_updm_update function prototype, rename it to soc/fsp.h. This
patch also removes a few unused includes.
Signed-off-by: Felix Held <felix-coreboot@felixheld.de>
Change-Id: I52c21f13520dbdfab37587d17b3a8a3b1a780f36
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51834
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Raul Rangel <rrangel@chromium.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add the UPD updating hook in early stage for customization.
BUG=b:117719313
BRANCH=zork
TEST=build,check the hook function been executed.
Signed-off-by: Chris Wang <chris.wang@amd.corp-partner.google.com>
Change-Id: I4954a438a51b29b086015624127e651fd06f971b
Reviewed-on: https://review.coreboot.org/c/coreboot/+/51181
Reviewed-by: EricR Lai <ericr_lai@compal.corp-partner.google.com>
Reviewed-by: Kangheui Won <khwon@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On zork, bootblock is part of RW firmware in non-recovery mode, so PCIe
GPIOs can be configured early on in bootblock rather than waiting until
romstage. This change moves the call to variant_pcie_gpio_configure() to
happen in bootblock and drops romstage.c file.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ic515304f35fe5623d58d6000efcb11fb9039e137
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43476
Reviewed-by: Paul Menzel <paulepanter@users.sourceforge.net>
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
gpio_set_stage_rom table is now configuring only PCIe related GPIOs in
romstage. This change moves the configuration of PCIe related GPIOs to
variant_pcie_gpio_configure() to keep all the configuration for WiFi and
non-WiFi PCIe pads in one place. It also drops the function
variant_romstage_gpio_table() as it is unused.
BUG=b:154351731
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: Ib1c41ba141dce6b52b6e0a250a3aa07c296068aa
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43475
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
mainboard_ec_init() does nothing in any stage other than ramstage. So,
this change drops the call to mainboard_ec_init() from
romstage.c. Additionally, it also drops ec.c from romstage and
verstage.
Change-Id: Iae0be4d678b0780cf532000a6c0fff1bce333c0e
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43117
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
|
|
|
|
|
|
|
|
|
| |
This change drops the function `variant_romstage_entry()` which is
unused on zork.
Change-Id: I140ab3e837971c4c7dbef5d27616043b5fc6c2c9
Signed-off-by: Furquan Shaikh <furquan@google.com>
Reviewed-on: https://review.coreboot.org/c/coreboot/+/43116
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This change replaces variant_wifi_romstage_gpio_table() with
variant_pcie_power_reset_configure() to handle the reset and power
sequencing for WiFi devices pre- and post- v3 version of schematics.
These are the requirements that need to be satisfied:
1. As per PCI Express M.2 Specification Revision 3.0,
Version 1.2, Section 3.1.4 "Power-up Timing", PERST# should stay
disabled until `TPVPGL` time duration after device power has
stabilized. Value of TPVPGL is implementation specific.
2. For Intel WiFi chip, it is known to get into a bad state if the
above requirement is violated and hence requires a power cycle.
3. On pre-v3 schematics:
- For both dalboz and trembyle references, GPIO42 drives
WIFI_AUX_RESET_L which is pulled up to PP3300_WIFI.
- For both dalboz and trembyle references, PP3300_WIFI is controlled
using GPIO29. This pad gets pulled high by default on PWRGOOD
because of internal pull-up. But, at RESET# it is known to have a
glitch. When GPIO29 gets pulled high, it causes WIFI_AUX_RESET_L to
be pulled high as well. This violates the PCIe power sequencing
requirements. Hence, for pre-v3 schematics on both dalboz and
trembyle, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET_L.
b. Disable power to WiFi.
c. Wait 10ms to allow WiFi power to go low.
d. Enable power to WiFi.
e. Wait 50ms as per PCIe specification.
f. Deassert WIFI_AUX_RESET_L.
4. On v3 schematics:
- For trembyle: WIFI_AUX_RESET_L is driven by GPIO86 which has an
internal PU as well as an external PU to PP3300_WIFI.
- For dalboz: WIFI_AUX_RESET is driven by GPIO29. This is active
high and has an internal PU. It also has an external 1K PD to
overcome internal PU.
- For both dalboz and trembyle references, PP3300_WIFI is
controlled by GPIO42 which has an internal PU and external
PD. Trembyle schematics have a comment saying strong PD of 2.2K but
the stuffed resistor is a weak one (499K). ON dalboz, it uses a
weak PD (which doesn't look correct and instead should be a strong
PD just like trembyle). Having a strong PD ensures that the WiFi
power is kept disabled when coming out of G3 until coreboot
configures GPIO42 as high.
- Thus, for v3 schematics, following sequence needs to be followed:
a. Assert WIFI_AUX_RESET{_L} signal.
b. Enable power to WiFi.
c. Wait 50ms as per PCIe specification.
d. Deassert WIFI_AUX_RESET{_L} signal.
BUG=b:157686402, b:158257076
TEST=Verified that QCA and AX200 cards both continue working. Tested
QCA on Dalboz and Trembyle. Tested AX200 on morphius.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Change-Id: I532131ee911d5efb5130d8710f3e01578f6c9627
Reviewed-on: https://review.coreboot.org/c/coreboot/+/42738
Reviewed-by: Aaron Durbin <adurbin@chromium.org>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|
|
This is a copy of the mb/google/zork directory from the chromiumos
coreboot-zork branch. This was from commit 29308ac8606.
See https://chromium.googlesource.com/chromiumos/third_party/coreboot/+/29308ac8606/src/mainboard/google/zork
Changes:
* Minor changes to make the board build.
* Add bootblock.c.
* Modify romstage.c
* Removed the FSP_X configs from zork/Kconfig since they should be
set in picasso/Kconfig. picasso/Kconfig doesn't currently define the
binaries since they haven't been published. To get a working build
a custom config that sets FSP_X_FILE is required.
BUG=b:157140753
TEST=Build trembyle and boot to OS
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Change-Id: I3933fa54e3f603985a0818852a1c77d8e248484f
Reviewed-on: https://review.coreboot.org/c/coreboot/+/41581
Reviewed-by: Furquan Shaikh <furquan@google.com>
Reviewed-by: Martin Roth <martinroth@google.com>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
|