From b39bc2510e2ef21d652f3bc3812669ab47b7a185 Mon Sep 17 00:00:00 2001 From: Felix Held Date: Wed, 22 Jan 2020 18:48:39 +0100 Subject: Documentation/superio: add formatting to generic PNP documentation Change-Id: Id12ec4d5f11f4285a1379cf32a5d0f6cd2ce9e70 Signed-off-by: Felix Held Reviewed-on: https://review.coreboot.org/c/coreboot/+/38519 Reviewed-by: Patrick Georgi Tested-by: build bot (Jenkins) --- Documentation/superio/common/pnp.md | 46 ++++++++++++++++++------------------- 1 file changed, 23 insertions(+), 23 deletions(-) diff --git a/Documentation/superio/common/pnp.md b/Documentation/superio/common/pnp.md index 314cac27edbc..3c17259e582d 100644 --- a/Documentation/superio/common/pnp.md +++ b/Documentation/superio/common/pnp.md @@ -15,13 +15,13 @@ specification is still the main reference though. Super I/O chips connected via LPC to the southbridge usually have their I/O-mapped configuration interface with a size of two bytes at the base -address 0x2e or 0x4e. Other PNP devices have their configuration +address `0x2e` or `0x4e`. Other PNP devices have their configuration interface at other addresses. The two byte registers allow access to an indirect 256 bytes big -register space that contains the configuration. By writing the index -to the lower byte (e.g. 0x2e), you can access the register contents at -that index by reading/writing the higher byte (e.g. 0x2f). +register space that contains the configuration. By writing the index to +the lower byte (e.g. `0x2e`), you can access the register contents at +that index by reading/writing the higher byte (e.g. `0x2f`). To prevent accidental changes of the Super I/O (SIO) configuration, the SIOs need a configuration mode unlock sequence. After changing the @@ -31,18 +31,18 @@ the configuration mode lock sequence. ## Logical device numbers (LDN) Each PNP device can contain multiple logical devices. The bytes from -0x00 to 0x2f in the indirect configuration register space are common -for all LDNs, but some SIO chips require a certain LDN to be selected -in order to write certain registers in there. An LDN gets selected by -writing the LDN number to the LDN select register 0x07. Registers 0x30 -to 0xFF are specific to each LDN number. +`0x00` to `0x2f` in the indirect configuration register space are common +for all LDNs, but some SIO chips require a certain LDN to be selected in +order to write certain registers in there. An LDN gets selected by +writing the LDN number to the LDN select register `0x07`. Registers +`0x30` to `0xff` are specific to each LDN number. coreboot encodes the physical LDN number in the lower byte of the LDN number. ### Virtual logical device numbers -Register 0x30 is the LDN enable register and since it is an 8 bit +Register `0x30` is the LDN enable register and since it is an 8 bit register, it can contain up to 8 enable bits for different parts of the functionality of that logical device. To set a certain enable bit in one physical LDN, the concept of virtual LDNs was introduced. @@ -54,7 +54,7 @@ part in the lower 3 bits of the higher byte of the LDN number. ## I/O resources -Starting at register address 0x60, each LDN has 2 byte wide I/O base +Starting at register address `0x60`, each LDN has 2 byte wide I/O base address registers. The size of an I/O resource is always a power of two. @@ -67,29 +67,29 @@ number of LSBs being zero, which can also be zero if the LSB is a one, the resource has N address bits and a size of 2\*\*N bytes. The mask address is also the highest possible address to map the I/O region. -A typical example for an I/O resource mask is 0x07f8 which is -0b0000011111111000 in binary notation. The three LSBs are zeros here, +A typical example for an I/O resource mask is `0x07f8` which is +`0b0000011111111000` in binary notation. The three LSBs are zeros here, so it's an eight byte I/O resource with three address offset bits inside the resource. The highest base address it can be mapped to is -0x07f8, so the region will end at 0x07ff. +`0x07f8`, so the region will end at `0x07ff`. The Super I/O datasheets typically contain the information about the I/O resource masks. On most Super I/O chips the mask can also be found -out by writing 0xffff to the corresponding I/O base address register +out by writing `0xffff` to the corresponding I/O base address register and reading back the value; since the lowest and highest bits are hard-wired to zero according to the I/O resource size and maximal possible I/O address, this gives the mask. ## IRQ resources -Each physical LDN has up to two configurable interrupt request -register pairs 0x70, 0x71 and 0x72, 0x73. Each pair can be configured -to use a certain IRQ number. Writing 1 to 15 into the first register +Each physical LDN has up to two configurable interrupt request register +pairs `0x70`, `0x71` and `0x72`, `0x73`. Each pair can be configured to +use a certain IRQ number. Writing 1 to 15 into the first register selects the IRQ number generated by the corresponding IRQ source and -enables IRQ generation; writing 0 to it disables the generation of -IRQs for the source. The second register selects the IRQ type (level -or edge) and IRQ level (high or low). For LPC SIOs the IRQ type is -hard-wired to edge. +enables IRQ generation; writing 0 to it disables the generation of IRQs +for the source. The second register selects the IRQ type (level or edge) +and IRQ level (high or low). For LPC SIOs the IRQ type is hard-wired to +edge. On the LPC bus a shared SERIRQ line is used to signal IRQs to the host; the IRQ number gets encoded by the number of LPC clock cycles @@ -106,7 +106,7 @@ number. The quiet mode is often broken. ## DRQ resources Each physical LDN has two legacy ISA-style DMA request channel -registers at 0x74 and 0x75. Those are only used for legacy devices +registers at `0x74` and `0x75`. Those are only used for legacy devices like parallel printer ports or floppy disk controllers. Each device using LPC legacy DMA needs its own LDMA line to the host. -- cgit v1.2.3