fw_config
	field DB_DISPLAY 0 3
		option DB_ABSENT	0
		option DB_HDMI		1
		option DB_DP		2
	end
end

chip soc/intel/alderlake
	register "sagv" = "SaGv_Enabled"

	# GPE configuration
	register "pmc_gpe0_dw1" = "GPP_H"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| I2C0              | Audio                     |
	#| I2C1              | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[1] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
		},
	}"

	register "usb2_ports[1]" = "USB2_PORT_EMPTY"	    # Disable Port 1
	register "usb2_ports[2]" = "USB2_PORT_EMPTY"	    # Disable Port 2
	register "usb2_ports[3]" = "USB2_PORT_EMPTY"        # Disable Port 3
	register "usb2_ports[4]" = "USB2_PORT_EMPTY"	    # Disable Port 4
	register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # USB HUB

	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Rear USB Type A
	register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# USB HUB

	register "tcss_ports[1]" = "TCSS_PORT_DEFAULT(OC1)"     # BTB
	register "tcss_ports[2]" = "TCSS_PORT_EMPTY"            # Disable Port2

	# I2C Port Config
	register "serial_io_i2c_mode" = "{
		[PchSerialIoIndexI2C0] = PchSerialIoPci,
		[PchSerialIoIndexI2C1] = PchSerialIoPci,
		[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C3] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C4] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C5] = PchSerialIoDisabled,
	}"

	register "serial_io_gspi_mode" = "{
		[PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
		[PchSerialIoIndexGSPI1] = PchSerialIoDisabled,
	}"

	register "ddi_ports_config" = "{
		[DDI_PORT_A] = DDI_ENABLE_HPD,
		[DDI_PORT_B] = DDI_ENABLE_HPD | DDI_ENABLE_DDC,
		[DDI_PORT_1] = DDI_ENABLE_HPD,
		[DDI_PORT_2] = DDI_ENABLE_HPD | DDI_ENABLE_DDC
	}"

	register "power_limits_config[ADL_P_142_242_282_15W_CORE]" = "{
		.tdp_pl1_override = 30,
	}"

	device domain 0 on
		device ref dtt on
			chip drivers/intel/dptf
				## sensor information
				register "options.tsr[0].desc" = ""DRAM_SOC""
				register "options.tsr[1].desc" = ""Ambient""
				register "options.tsr[2].desc" = ""Charger""
				register "options.tsr[3].desc" = ""WWAN""

				# TODO: below values are initial reference values only
				## Active Policy
				register "policies.active" = "{
					[0] = {
						.target = DPTF_CPU,
						.thresholds = {
								TEMP_PCT(80, 97),
								TEMP_PCT(65, 93),
								TEMP_PCT(58, 86),
								TEMP_PCT(50, 80),
								TEMP_PCT(45, 64),
								TEMP_PCT(43, 52),
								TEMP_PCT(40, 47),
								TEMP_PCT(35, 40),
						}
					},
					[1] = {
						.target = DPTF_TEMP_SENSOR_0,
						.thresholds = {
								TEMP_PCT(75, 97),
								TEMP_PCT(70, 93),
								TEMP_PCT(60, 86),
								TEMP_PCT(52, 80),
								TEMP_PCT(47, 64),
								TEMP_PCT(43, 52),
								TEMP_PCT(40, 47),
								TEMP_PCT(35, 40),
						}
					},
					[2] = {
						.target = DPTF_TEMP_SENSOR_1,
						.thresholds = {
								TEMP_PCT(75, 97),
								TEMP_PCT(70, 93),
								TEMP_PCT(60, 86),
								TEMP_PCT(52, 80),
								TEMP_PCT(47, 64),
								TEMP_PCT(43, 52),
								TEMP_PCT(40, 47),
								TEMP_PCT(35, 40),
						}
					},
					[3] = {
						.target = DPTF_TEMP_SENSOR_2,
						.thresholds = {
								TEMP_PCT(75, 97),
								TEMP_PCT(70, 93),
								TEMP_PCT(60, 86),
								TEMP_PCT(52, 80),
								TEMP_PCT(47, 64),
								TEMP_PCT(43, 52),
								TEMP_PCT(40, 47),
								TEMP_PCT(35, 40),
						}
					},
					[4] = {
						.target = DPTF_TEMP_SENSOR_3,
						.thresholds = {
								TEMP_PCT(75, 97),
								TEMP_PCT(70, 93),
								TEMP_PCT(60, 86),
								TEMP_PCT(52, 80),
								TEMP_PCT(47, 64),
								TEMP_PCT(43, 52),
								TEMP_PCT(40, 47),
								TEMP_PCT(35, 40),
						}
					}
				}"

				## Passive Policy
				register "policies.passive" = "{
					[0] = DPTF_PASSIVE(CPU,         CPU,           90, 10000),
					[1] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_0, 90, 10000),
					[2] = DPTF_PASSIVE(CPU,     	TEMP_SENSOR_1, 90, 10000),
					[3] = DPTF_PASSIVE(CHARGER,	TEMP_SENSOR_2, 90, 10000),
					[4] = DPTF_PASSIVE(CPU,         TEMP_SENSOR_3, 90, 10000),
				}"

				## Critical Policy
				register "policies.critical" = "{
					[0] = DPTF_CRITICAL(CPU,               100, SHUTDOWN),
					[1] = DPTF_CRITICAL(TEMP_SENSOR_0,      93, SHUTDOWN),
					[2] = DPTF_CRITICAL(TEMP_SENSOR_1,      93, SHUTDOWN),
					[3] = DPTF_CRITICAL(TEMP_SENSOR_2,      93, SHUTDOWN),
					[4] = DPTF_CRITICAL(TEMP_SENSOR_3,      93, SHUTDOWN),
				}"

				register "controls.power_limits" = "{
					.pl1 = {
							.min_power = 12000,
							.max_power = 25000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 28 * MSECS_PER_SEC,
							.granularity = 500,
						},
					.pl2 = {
							.min_power = 39000,
							.max_power = 39000,
							.time_window_min = 28 * MSECS_PER_SEC,
							.time_window_max = 32 * MSECS_PER_SEC,
							.granularity = 1000,
						}
				}"

				register "oem_data.oem_variables" = "{
						[0] = 0x0
				}"

				## Charger Performance Control (Control, mA)
				register "controls.charger_perf" = "{
					[0] = { 255, 1700 },
					[1] = {  24, 1500 },
					[2] = {  16, 1000 },
					[3] = {   8,  500 }
				}"
				## Fan Performance Control (Percent, Speed, Noise, Power)
				register "controls.fan_perf" = "{
					[0] = {  90, 6700, 220, 2200, },
					[1] = {  80, 5800, 180, 1800, },
					[2] = {  70, 5000, 145, 1450, },
					[3] = {  60, 4900, 115, 1150, },
					[4] = {  50, 3838,  90,  900, },
					[5] = {  40, 2904,  55,  550, },
					[6] = {  30, 2337,  30,  300, },
					[7] = {  20, 1608,  15,  150, },
					[8] = {  10,  800,  10,  100, },
					[9] = {   0,    0,   0,   50, }
				}"

				## Fan options
				register "options.fan.fine_grained_control" = "1"
				register "options.fan.step_size" = "2"

				device generic 0 alias dptf_policy on end
			end
		end
		device ref pcie_rp5 on
			# Enable WLAN PCIE 5 using clk 2
			register "pch_pcie_rp[PCH_RP(5)]" = "{
				.clk_src = 2,
				.clk_req = 2,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip drivers/wifi/generic
				register "wake" = "GPE0_DW1_03"
				device pci 00.0 on end
			end
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)"
				register "srcclk_pin" = "2"
				device generic 0 on end
			end
		end
		device ref pcie_rp6 on
			# Enable PCIe-to-eMMC bridge PCIE 6 using clk 1
			register "pch_pcie_rp[PCH_RP(6)]" = "{
				.clk_src = 1,
				.clk_req = 1,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
			chip soc/intel/common/block/pcie/rtd3
				register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)"
				register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)"
				register "srcclk_pin" = "1"
				register "reset_delay_ms" = "50"
				register "enable_delay_ms" = "20"
				device generic 0 alias emmc_rtd3 on end
			end
		end # BH799BBLN
		device ref pcie_rp7 on
			chip drivers/net
				register "customized_leds" = "0x05af"
				register "wake" = "GPE0_DW0_07" #GPP_A7
				register "device_index" = "0"
				device pci 00.0 on end
			end
		end # RTL8111K Ethernet NIC
		device ref pcie_rp8 off end
		device ref pcie_rp9 off end

		device ref pcie4_0 on
		# Enable CPU PCIE RP 1 using CLK 0
			register "cpu_pcie_rp[CPU_RP(1)]" = "{
				.clk_req = 0,
				.clk_src = 0,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
		end

		device ref cnvi_wifi on
			chip drivers/wifi/generic
				register "wake" = "GPE0_PME_B0"
				device generic 0 on end
			end
		end

		device ref tbt_pcie_rp0 off end
		device ref tbt_pcie_rp1 off end
		device ref tbt_pcie_rp2 off end

		device ref tcss_dma0 off end
		device ref tcss_dma1 off end

		device ref i2c0 on
			chip drivers/i2c/generic
				register "hid" = ""RTL5682""
				register "name" = ""RT58""
				register "desc" = ""Headset Codec""
				register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)"
				# Set the jd_src to RT5668_JD1 for jack detection
				register "property_count" = "1"
				register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER"
				register "property_list[0].name" = ""realtek,jd-src""
				register "property_list[0].integer" = "1"
				device i2c 1a on end
			end
		end #I2C0
		device ref gspi1 off end
		device ref pch_espi on
			chip ec/google/chromeec
				use conn0 as mux_conn[0]
				device pnp 0c09.0 on end
			end
		end
		device ref pmc hidden
			chip drivers/intel/pmc_mux
				device generic 0 on
					chip drivers/intel/pmc_mux/conn
						use usb2_port1 as usb2_port
						use tcss_usb3_port1 as usb3_port
						device generic 0 alias conn0 on end
					end
				end
			end
		end
		device ref tcss_xhci on
			chip drivers/usb/acpi
				device ref tcss_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_C(FRONT, RIGHT, ACPI_PLD_GROUP(1, 1))"
						device ref tcss_usb3_port1 on end
					end
				end
			end
		end
		device ref xhci on
			chip drivers/usb/acpi
				device ref xhci_root_hub on
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-C Port C0 (MLB)""
						register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_C(FRONT, RIGHT, ACPI_PLD_GROUP(1, 1))"
						device ref usb2_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Hub""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(BACK, RIGHT, ACPI_PLD_GROUP(5, 1))"
						device ref usb2_port6 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A2 (MLB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(6, 1))"
						device ref usb2_port7 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A1 (MLB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(4, 1))"
						device ref usb2_port8 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Type-A Port A0 (MLB)""
						register "type" = "UPC_TYPE_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 2))"
						device ref usb2_port9 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB2 Bluetooth""
						register "type" = "UPC_TYPE_INTERNAL"
						register "reset_gpio" =
							"ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
						device ref usb2_port10 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A0 (MLB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 2))"
						device ref usb3_port1 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A1 (MLB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(4, 1))"
						device ref usb3_port2 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB3 Type-A Port A2 (MLB)""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(6, 1))"
						device ref usb3_port3 on end
					end
					chip drivers/usb/acpi
						register "desc" = ""USB Hub""
						register "type" = "UPC_TYPE_USB3_A"
						register "use_custom_pld" = "true"
						register "custom_pld" =
							"ACPI_PLD_TYPE_A(BACK, RIGHT, ACPI_PLD_GROUP(5, 1))"
						device ref usb3_port4 on end
					end
				end
			end
		end
	end
end