/* SPDX-License-Identifier: GPL-2.0-only */

#include <bootblock_common.h>
#include <device/pnp_ops.h>
#include <device/pnp_type.h>
#include <stdint.h>
#include <amdblocks/acpimmio.h>
#include <superio/fintek/common/fintek.h>
#include <superio/fintek/f71869ad/f71869ad.h>

/* Ensure Super I/O config address (i.e., 0x2e or 0x4e) matches that of devicetree.cb */
#define SUPERIO_ADDRESS 0x4e

#define SERIAL_DEV PNP_DEV(SUPERIO_ADDRESS, F71869AD_SP1)
#define GPIO_DEV PNP_DEV(SUPERIO_ADDRESS, F71869AD_GPIO)

/* GPIO configuration */
static void gpio_init(pnp_devfn_t dev)
{
	pnp_enter_conf_state(dev);
	pnp_set_logical_device(dev);
	pnp_set_enable(dev, 0);
	pnp_write_config(dev, 0x60, 0x0a); //Base addr high
	pnp_write_config(dev, 0x61, 0x00); //Base addr low
	pnp_write_config(dev, 0xe0, 0x04); //GPIO1 output enable
	pnp_write_config(dev, 0xe1, 0xff); //GPIO1 output data
	pnp_write_config(dev, 0xe3, 0x04); //GPIO1 drive enable
	pnp_write_config(dev, 0xe4, 0x00); //GPIO1 PME enable
	pnp_write_config(dev, 0xe5, 0x00); //GPIO1 input detect select
	pnp_write_config(dev, 0xe6, 0x40); //GPIO1 event status
	pnp_write_config(dev, 0xd0, 0x00); //GPIO2 output enable
	pnp_write_config(dev, 0xd1, 0xff); //GPIO2 output data
	pnp_write_config(dev, 0xd3, 0x00); //GPIO2 drive enable
	pnp_write_config(dev, 0xc0, 0x00); //GPIO3 output enable
	pnp_write_config(dev, 0xc1, 0xff); //GPIO3 output data
	pnp_write_config(dev, 0xb0, 0x04); //GPIO4 output enable
	pnp_write_config(dev, 0xb1, 0x04); //GPIO4 output data
	pnp_write_config(dev, 0xb3, 0x04); //GPIO4 drive enable
	pnp_write_config(dev, 0xb4, 0x00); //GPIO4 PME enable
	pnp_write_config(dev, 0xb5, 0x00); //GPIO4 input detect select
	pnp_write_config(dev, 0xb6, 0x00); //GPIO4 event status
	pnp_write_config(dev, 0xa0, 0x00); //GPIO5 output enable
	pnp_write_config(dev, 0xa1, 0x1f); //GPIO5 output data
	pnp_write_config(dev, 0xa3, 0x00); //GPIO5 drive enable
	pnp_write_config(dev, 0xa4, 0x00); //GPIO5 PME enable
	pnp_write_config(dev, 0xa5, 0xff); //GPIO5 input detect select
	pnp_write_config(dev, 0xa6, 0xe0); //GPIO5 event status
	pnp_write_config(dev, 0x90, 0x00); //GPIO6 output enable
	pnp_write_config(dev, 0x91, 0xff); //GPIO6 output data
	pnp_write_config(dev, 0x93, 0x00); //GPIO6 drive enable
	pnp_write_config(dev, 0x80, 0x00); //GPIO7 output enable
	pnp_write_config(dev, 0x81, 0xff); //GPIO7 output data
	pnp_write_config(dev, 0x83, 0x00); //GPIO7 drive enable
	pnp_set_enable(dev, 1);
	pnp_exit_conf_state(dev);
}

static void sbxxx_enable_48mhzout(void)
{
	/* most likely programming to 48MHz out signal */
	u32 reg32;
	reg32 = misc_read32(0x28);
	reg32 &= 0xffc7ffff;
	reg32 |= 0x00100000;
	misc_write32(0x28, reg32);

	reg32 = misc_read32(0x40);
	reg32 &= ~0x80u;
	misc_write32(0x40, reg32);
}

void bootblock_mainboard_early_init(void)
{
	/* enable SIO clock */
	sbxxx_enable_48mhzout();

	/* Initialize GPIO registers */
	gpio_init(GPIO_DEV);

	/* Enable serial console */
	fintek_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
}