/* SPDX-License-Identifier: GPL-2.0-only */

#include <bootstate.h>
#include <console/console.h>
#include <device/mmio.h>
#include <device/device.h>
#include <intelblocks/pmc.h>
#include <intelblocks/pmclib.h>
#include <intelblocks/rtc.h>
#include <soc/pci_devs.h>
#include <soc/pm.h>
#include <soc/soc_chip.h>

static void config_deep_sX(uint32_t offset, uint32_t mask, int sx, int enable)
{
	uint32_t reg;
	uint8_t *pmcbase = pmc_mmio_regs();

	printk(BIOS_DEBUG, "%sabling Deep S%c\n",
		enable ? "En" : "Dis", sx + '0');
	reg = read32(pmcbase + offset);
	if (enable)
		reg |= mask;
	else
		reg &= ~mask;
	write32(pmcbase + offset, reg);
}

static void config_deep_s5(int on_ac, int on_dc)
{
	/* Treat S4 the same as S5. */
	config_deep_sX(S4_PWRGATE_POL, S4AC_GATE_SUS, 4, on_ac);
	config_deep_sX(S4_PWRGATE_POL, S4DC_GATE_SUS, 4, on_dc);
	config_deep_sX(S5_PWRGATE_POL, S5AC_GATE_SUS, 5, on_ac);
	config_deep_sX(S5_PWRGATE_POL, S5DC_GATE_SUS, 5, on_dc);
}

static void config_deep_s3(int on_ac, int on_dc)
{
	config_deep_sX(S3_PWRGATE_POL, S3AC_GATE_SUS, 3, on_ac);
	config_deep_sX(S3_PWRGATE_POL, S3DC_GATE_SUS, 3, on_dc);
}

static void config_deep_sx(uint32_t deepsx_config)
{
	uint32_t reg;
	uint8_t *pmcbase = pmc_mmio_regs();

	reg = read32(pmcbase + DSX_CFG);
	reg &= ~DSX_CFG_MASK;
	reg |= deepsx_config;
	write32(pmcbase + DSX_CFG, reg);
}

static void pmc_init(void *unused)
{
	const config_t *config = config_of_soc();

	rtc_init();

	pmc_set_power_failure_state(true);
	pmc_gpe_init();

	pmc_set_acpi_mode();

	config_deep_s3(config->deep_s3_enable_ac, config->deep_s3_enable_dc);
	config_deep_s5(config->deep_s5_enable_ac, config->deep_s5_enable_dc);
	config_deep_sx(config->deep_sx_config);

	/*
	 * Disable ACPI PM timer based on Kconfig
	 *
	 * Disabling ACPI PM timer is necessary for XTAL OSC shutdown.
	 * Disabling ACPI PM timer also switches off TCO
	 */
	if (!CONFIG(USE_PM_ACPI_TIMER))
		setbits8(pmc_mmio_regs() + PCH_PWRM_ACPI_TMR_CTL, ACPI_TIM_DIS);

	/*
	 * Clear PMCON status bits (Global Reset/Power Failure/Host Reset Status bits)
	 *
	 * Perform the PMCON status bit clear operation from `.final`
	 * to cover any such chances where later boot stage requested a global
	 * reset and PMCON status bit remains set.
	 */
	pmc_clear_pmcon_sts();
}

/*
* Initialize PMC controller.
*
* PMC controller gets hidden from PCI bus during FSP-Silicon init call.
* Hence PCI enumeration can't be used to initialize bus device and
* allocate resources.
*/
BOOT_STATE_INIT_ENTRY(BS_DEV_INIT_CHIPS, BS_ON_EXIT, pmc_init, NULL);