buspirate_spi: Add support for variable serial speeds

This patch sets the default baud rate for communication between
the host device and the Bus Pirate for hardware versions 3.0
and greater to 2M baud.

It also introduces the ability to manually set the baud rate via
the added 'serialspeed' programmer parameter.

This is done in two parts. Firstly, the requested serial speed is looked up
in a table to determine the appropriate clock divisor and the divisor is sent
to the bus pirate. Then, the system's baud rate for the selected serial port
is set using serial.c's 'serialport_config'. This function's prototype had to
be added to programmer.h.

In testing, using the 2M baud rate was able to significantly decrease
flash times (down from 20+ minutes to less than 2 minutes for an 8MB flash).

Change-Id: I3706f17a94fdf056063f2ad4a5f0a219665cdcbf
Signed-off-by: Shawn Anastasio <shawnanastasio@yahoo.com>
Reviewed-on: https://review.coreboot.org/23057
Reviewed-by: Nico Huber <nico.h@gmx.de>
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>

1 files changed, 121 insertions, 11 deletions

diff --git a/buspirate_spi.c b/buspirate_spi.c
index 6f4c6d06e..f82541552 100644
--- a/buspirate_spi.c
+++ b/buspirate_spi.c
@@ -30,16 +30,18 @@
 /* Change this to #define if you want to test without a serial implementation */
 #undef FAKE_COMMUNICATION
 
-struct buspirate_spispeeds {
+struct buspirate_speeds {
 	const char *name;
 	const int speed;
 };
 
+#define BP_DEFAULTBAUD 115200
+
 #ifndef FAKE_COMMUNICATION
 static int buspirate_serialport_setup(char *dev)
 {
 	/* 115200bps, 8 databits, no parity, 1 stopbit */
-	sp_fd = sp_openserport(dev, 115200);
+	sp_fd = sp_openserport(dev, BP_DEFAULTBAUD);
  	if (sp_fd == SER_INV_FD)
 		return 1;
 	return 0;
@@ -146,7 +148,7 @@ static struct spi_master spi_master_buspirate = {
 	.write_aai	= default_spi_write_aai,
 };
 
-static const struct buspirate_spispeeds spispeeds[] = {
+static const struct buspirate_speeds spispeeds[] = {
 	{"30k",		0x0},
 	{"125k",	0x1},
 	{"250k",	0x2},
@@ -155,7 +157,16 @@ static const struct buspirate_spispeeds spispeeds[] = {
 	{"2.6M",	0x5},
 	{"4M",		0x6},
 	{"8M",		0x7},
-	{NULL,		0x0},
+	{NULL,		0x0}
+};
+
+static const struct buspirate_speeds serialspeeds[] = {
+	{"115200",  115200},
+	{"230400",  230400},
+	{"250000",  250000},
+	{"2000000", 2000000},
+	{"2M",      2000000},
+	{NULL,      0}
 };
 
 static int buspirate_spi_shutdown(void *data)
@@ -199,15 +210,26 @@ out_shutdown:
 }
 
 #define BP_FWVERSION(a,b)	((a) << 8 | (b))
+#define BP_HWVERSION(a,b)	BP_FWVERSION(a,b)
+
+/**
+ * The Bus Pirate's PIC microcontroller supports custom baud rates by manually specifying a
+ * clock divisor that can be calculated with the formula (16000000 / (4 * baud)) - 1.
+ */
+#define BP_DIVISOR(baud) ((4000000/(baud)) - 1)
 
 int buspirate_spi_init(void)
 {
 	char *tmp;
 	char *dev;
 	int i;
+	int cnt;
 	unsigned int fw_version_major = 0;
 	unsigned int fw_version_minor = 0;
+	unsigned int hw_version_major = 0;
+	unsigned int hw_version_minor = 0;
 	int spispeed = 0x7;
+	int serialspeed_index = -1;
 	int ret = 0;
 	int pullup = 0;
 
@@ -234,6 +256,20 @@ int buspirate_spi_init(void)
 	}
 	free(tmp);
 
+	/* Extract serialspeed paramater */
+	tmp = extract_programmer_param("serialspeed");
+	if (tmp) {
+		for (i = 0; serialspeeds[i].name; i++) {
+			if (!strncasecmp(serialspeeds[i].name, tmp, strlen(serialspeeds[i].name))) {
+				serialspeed_index = i;
+				break;
+			}
+		}
+		if (!serialspeeds[i].name)
+			msg_perr("Invalid serial speed %s, using default.\n", tmp);
+	}
+	free(tmp);
+
 	tmp = extract_programmer_param("pullups");
 	if (tmp) {
 		if (strcasecmp("on", tmp) == 0)
@@ -313,7 +349,20 @@ int buspirate_spi_init(void)
 			break;
 	}
 	bp_commbuf[i] = '\0';
-	msg_pdbg("Detected Bus Pirate hardware %s\n", bp_commbuf);
+	msg_pdbg("Detected Bus Pirate hardware ");
+	if (bp_commbuf[0] != 'v')
+		msg_pdbg("(unknown version number format)");
+	else if (!strchr("0123456789", bp_commbuf[1]))
+		msg_pdbg("(unknown version number format)");
+	else {
+		hw_version_major = strtoul((char *)bp_commbuf + 1, &tmp, 10);
+		while ((*tmp != '\0') && !strchr("0123456789", *tmp))
+			tmp++;
+		hw_version_minor = strtoul(tmp, NULL, 10);
+		msg_pdbg("%u.%u", hw_version_major, hw_version_minor);
+	}
+	msg_pdbg2(" (\"%s\")", bp_commbuf);
+	msg_pdbg("\n");
 
 	if ((ret = buspirate_wait_for_string(bp_commbuf, "irmware ")))
 		return ret;
@@ -342,7 +391,7 @@ int buspirate_spi_init(void)
 
 	if ((ret = buspirate_wait_for_string(bp_commbuf, "HiZ>")))
 		return ret;
-	
+
 	/* Tell the user about missing SPI binary mode in firmware 2.3 and older. */
 	if (BP_FWVERSION(fw_version_major, fw_version_minor) < BP_FWVERSION(2, 4)) {
 		msg_pinfo("Bus Pirate firmware 2.3 and older does not support binary SPI access.\n");
@@ -352,7 +401,7 @@ int buspirate_spi_init(void)
 
 	/* Use fast SPI mode in firmware 5.5 and newer. */
 	if (BP_FWVERSION(fw_version_major, fw_version_minor) >= BP_FWVERSION(5, 5)) {
-		msg_pdbg("Using SPI command set v2.\n"); 
+		msg_pdbg("Using SPI command set v2.\n");
 		/* Sensible default buffer size. */
 		if (buspirate_commbuf_grow(260 + 5))
 			return ERROR_OOM;
@@ -379,10 +428,71 @@ int buspirate_spi_init(void)
 			msg_pinfo("It is recommended to upgrade to firmware 6.2 or newer.\n");
 			spispeed = 0x4;
 		}
-		
+
 	/* This works because speeds numbering starts at 0 and is contiguous. */
 	msg_pdbg("SPI speed is %sHz\n", spispeeds[spispeed].name);
 
+	/* Set 2M baud serial speed by default on hardware 3.0 and newer if a custom speed was not set */
+	if (serialspeed_index == -1 && BP_HWVERSION(hw_version_major, hw_version_minor) >= BP_HWVERSION(3, 0)) {
+		serialspeed_index = ARRAY_SIZE(serialspeeds) - 2;
+		msg_pdbg("Bus Pirate v3 or newer detected. Set serial speed to 2M baud.\n");
+	}
+
+	/* Set custom serial speed if specified */
+	if (serialspeed_index != -1) {
+		if (BP_FWVERSION(fw_version_major, fw_version_minor) < BP_FWVERSION(5, 5)) {
+			/* This feature requires firmware 5.5 or newer */
+			msg_perr("Bus Pirate firmware 5.4 and older does not support custom serial speeds."
+				 "Using default speed of 115200 baud.\n");
+		} else if (serialspeeds[serialspeed_index].speed != BP_DEFAULTBAUD) {
+			/* Set the serial speed to match the user's choice if it doesn't already */
+
+			if (BP_HWVERSION(hw_version_major, hw_version_minor) < BP_HWVERSION(3, 0))
+				msg_pwarn("Increased serial speeds may not work on older (<3.0) Bus Pirates."
+					" Continue at your own risk.\n");
+
+			/* Enter baud rate configuration mode */
+			cnt = snprintf((char *)bp_commbuf, DEFAULT_BUFSIZE, "b\n");
+			if ((ret = buspirate_sendrecv(bp_commbuf, cnt, 0)))
+				return ret;
+			if ((ret = buspirate_wait_for_string(bp_commbuf, ">")))
+				return ret;
+
+			/* Enter manual clock divisor entry mode */
+			cnt = snprintf((char *)bp_commbuf, DEFAULT_BUFSIZE, "10\n");
+			if ((ret = buspirate_sendrecv(bp_commbuf, cnt, 0)))
+				return ret;
+			if ((ret = buspirate_wait_for_string(bp_commbuf, ">")))
+				return ret;
+
+			/* Set the clock divisor to the value calculated from the user's input */
+			cnt = snprintf((char *)bp_commbuf, DEFAULT_BUFSIZE, "%d\n",
+				BP_DIVISOR(serialspeeds[serialspeed_index].speed));
+
+			if ((ret = buspirate_sendrecv(bp_commbuf, cnt, 0)))
+				return ret;
+			sleep(1);
+
+			/* Reconfigure the host's serial baud rate to the new value */
+			if ((ret = serialport_config(sp_fd, serialspeeds[serialspeed_index].speed))) {
+				msg_perr("Unable to configure system baud rate to specified value.");
+				return ret;
+			}
+
+			/* Return to the main prompt */
+			bp_commbuf[0] = ' ';
+			if ((ret = buspirate_sendrecv(bp_commbuf, 1, 0)))
+				return ret;
+			if ((ret = buspirate_wait_for_string(bp_commbuf, "HiZ>")))
+				return ret;
+
+			msg_pdbg("Serial speed is %d baud\n", serialspeeds[serialspeed_index].speed);
+		}
+
+	}
+
+
+
 	/* Enter raw bitbang mode */
 	for (i = 0; i < 20; i++) {
 		bp_commbuf[0] = 0x00;
@@ -434,7 +544,7 @@ int buspirate_spi_init(void)
 		msg_perr("Protocol error while setting SPI speed!\n");
 		return 1;
 	}
-	
+
 	/* Set SPI config: output type, idle, clock edge, sample */
 	bp_commbuf[0] = 0x80 | 0xa;
 	ret = buspirate_sendrecv(bp_commbuf, 1, 1);
@@ -534,7 +644,7 @@ static int buspirate_spi_send_command_v2(struct flashctx *flash, unsigned int wr
 	bp_commbuf[i++] = (readcnt >> 8) & 0xff;
 	bp_commbuf[i++] = readcnt & 0xff;
 	memcpy(bp_commbuf + i, writearr, writecnt);
-	
+
 	ret = buspirate_sendrecv(bp_commbuf, i + writecnt, 1 + readcnt);
 
 	if (ret) {
@@ -551,4 +661,4 @@ static int buspirate_spi_send_command_v2(struct flashctx *flash, unsigned int wr
 	memcpy(readarr, bp_commbuf + 1, readcnt);
 
 	return ret;
-}
+}
\ No newline at end of file