thermal: exynos: Add extra entries in the tmu platform data

This patch adds entries min_efuse_value, max_efuse_value, default_temp_offset,
trigger_type, cal_type, trim_first_point, trim_second_point, max_trigger_level
trigger_enable in the TMU platform data structure. Also the driver is modified
to use the data passed by these new platform memebers instead of the constant
macros. All these changes helps in separating the SOC specific data part from
the TMU driver.

Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Eduardo Valentin <eduardo.valentin@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>

1 files changed, 31 insertions, 18 deletions

diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h
index 1857609518f2..473acae04f82 100644
--- a/drivers/thermal/samsung/exynos_tmu.h
+++ b/drivers/thermal/samsung/exynos_tmu.h
@@ -32,6 +32,11 @@ enum calibration_type {
 	TYPE_NONE,
 };
 
+enum calibration_mode {
+	SW_MODE,
+	HW_MODE,
+};
+
 enum soc_type {
 	SOC_ARCH_EXYNOS4210 = 1,
 	SOC_ARCH_EXYNOS,
@@ -57,18 +62,15 @@ enum soc_type {
  *	3: temperature for trigger_level3 interrupt
  *	   condition for trigger_level3 interrupt:
  *		current temperature > threshold + trigger_levels[3]
- * @trigger_level0_en:
- *	1 = enable trigger_level0 interrupt,
- *	0 = disable trigger_level0 interrupt
- * @trigger_level1_en:
- *	1 = enable trigger_level1 interrupt,
- *	0 = disable trigger_level1 interrupt
- * @trigger_level2_en:
- *	1 = enable trigger_level2 interrupt,
- *	0 = disable trigger_level2 interrupt
- * @trigger_level3_en:
- *	1 = enable trigger_level3 interrupt,
- *	0 = disable trigger_level3 interrupt
+ * @trigger_type: defines the type of trigger. Possible values are,
+ *	THROTTLE_ACTIVE trigger type
+ *	THROTTLE_PASSIVE trigger type
+ *	SW_TRIP trigger type
+ *	HW_TRIP
+ * @trigger_enable[]: array to denote which trigger levels are enabled.
+ *	1 = enable trigger_level[] interrupt,
+ *	0 = disable trigger_level[] interrupt
+ * @max_trigger_level: max trigger level supported by the TMU
  * @gain: gain of amplifier in the positive-TC generator block
  *	0 <= gain <= 15
  * @reference_voltage: reference voltage of amplifier
@@ -78,7 +80,13 @@ enum soc_type {
  *	000, 100, 101, 110 and 111 can be different modes
  * @type: determines the type of SOC
  * @efuse_value: platform defined fuse value
+ * @min_efuse_value: minimum valid trimming data
+ * @max_efuse_value: maximum valid trimming data
+ * @first_point_trim: temp value of the first point trimming
+ * @second_point_trim: temp value of the second point trimming
+ * @default_temp_offset: default temperature offset in case of no trimming
  * @cal_type: calibration type for temperature
+ * @cal_mode: calibration mode for temperature
  * @freq_clip_table: Table representing frequency reduction percentage.
  * @freq_tab_count: Count of the above table as frequency reduction may
  *	applicable to only some of the trigger levels.
@@ -88,18 +96,23 @@ enum soc_type {
 struct exynos_tmu_platform_data {
 	u8 threshold;
 	u8 threshold_falling;
-	u8 trigger_levels[4];
-	bool trigger_level0_en;
-	bool trigger_level1_en;
-	bool trigger_level2_en;
-	bool trigger_level3_en;
-
+	u8 trigger_levels[MAX_TRIP_COUNT];
+	enum trigger_type trigger_type[MAX_TRIP_COUNT];
+	bool trigger_enable[MAX_TRIP_COUNT];
+	u8 max_trigger_level;
 	u8 gain;
 	u8 reference_voltage;
 	u8 noise_cancel_mode;
+
 	u32 efuse_value;
+	u32 min_efuse_value;
+	u32 max_efuse_value;
+	u8 first_point_trim;
+	u8 second_point_trim;
+	u8 default_temp_offset;
 
 	enum calibration_type cal_type;
+	enum calibration_mode cal_mode;
 	enum soc_type type;
 	struct freq_clip_table freq_tab[4];
 	unsigned int freq_tab_count;