diff options
Diffstat (limited to 'Documentation/driver-api/serial/rocket.rst')
| -rw-r--r-- | Documentation/driver-api/serial/rocket.rst | 185 |
1 files changed, 185 insertions, 0 deletions
diff --git a/Documentation/driver-api/serial/rocket.rst b/Documentation/driver-api/serial/rocket.rst new file mode 100644 index 000000000000..23761eae4282 --- /dev/null +++ b/Documentation/driver-api/serial/rocket.rst @@ -0,0 +1,185 @@ +================================================ +Comtrol(tm) RocketPort(R)/RocketModem(TM) Series +================================================ + +Device Driver for the Linux Operating System +============================================ + +Product overview +---------------- + +This driver provides a loadable kernel driver for the Comtrol RocketPort +and RocketModem PCI boards. These boards provide, 2, 4, 8, 16, or 32 +high-speed serial ports or modems. This driver supports up to a combination +of four RocketPort or RocketModems boards in one machine simultaneously. +This file assumes that you are using the RocketPort driver which is +integrated into the kernel sources. + +The driver can also be installed as an external module using the usual +"make;make install" routine. This external module driver, obtainable +from the Comtrol website listed below, is useful for updating the driver +or installing it into kernels which do not have the driver configured +into them. Installations instructions for the external module +are in the included README and HW_INSTALL files. + +RocketPort ISA and RocketModem II PCI boards currently are only supported by +this driver in module form. + +The RocketPort ISA board requires I/O ports to be configured by the DIP +switches on the board. See the section "ISA Rocketport Boards" below for +information on how to set the DIP switches. + +You pass the I/O port to the driver using the following module parameters: + +board1: + I/O port for the first ISA board +board2: + I/O port for the second ISA board +board3: + I/O port for the third ISA board +board4: + I/O port for the fourth ISA board + +There is a set of utilities and scripts provided with the external driver +(downloadable from http://www.comtrol.com) that ease the configuration and +setup of the ISA cards. + +The RocketModem II PCI boards require firmware to be loaded into the card +before it will function. The driver has only been tested as a module for this +board. + +Installation Procedures +----------------------- + +RocketPort/RocketModem PCI cards require no driver configuration, they are +automatically detected and configured. + +The RocketPort driver can be installed as a module (recommended) or built +into the kernel. This is selected, as for other drivers, through the `make config` +command from the root of the Linux source tree during the kernel build process. + +The RocketPort/RocketModem serial ports installed by this driver are assigned +device major number 46, and will be named /dev/ttyRx, where x is the port number +starting at zero (ex. /dev/ttyR0, /devttyR1, ...). If you have multiple cards +installed in the system, the mapping of port names to serial ports is displayed +in the system log at /var/log/messages. + +If installed as a module, the module must be loaded. This can be done +manually by entering "modprobe rocket". To have the module loaded automatically +upon system boot, edit a `/etc/modprobe.d/*.conf` file and add the line +"alias char-major-46 rocket". + +In order to use the ports, their device names (nodes) must be created with mknod. +This is only required once, the system will retain the names once created. To +create the RocketPort/RocketModem device names, use the command +"mknod /dev/ttyRx c 46 x" where x is the port number starting at zero. + +For example:: + + > mknod /dev/ttyR0 c 46 0 + > mknod /dev/ttyR1 c 46 1 + > mknod /dev/ttyR2 c 46 2 + +The Linux script MAKEDEV will create the first 16 ttyRx device names (nodes) +for you:: + + >/dev/MAKEDEV ttyR + +ISA Rocketport Boards +--------------------- + +You must assign and configure the I/O addresses used by the ISA Rocketport +card before installing and using it. This is done by setting a set of DIP +switches on the Rocketport board. + + +Setting the I/O address +----------------------- + +Before installing RocketPort(R) or RocketPort RA boards, you must find +a range of I/O addresses for it to use. The first RocketPort card +requires a 68-byte contiguous block of I/O addresses, starting at one +of the following: 0x100h, 0x140h, 0x180h, 0x200h, 0x240h, 0x280h, +0x300h, 0x340h, 0x380h. This I/O address must be reflected in the DIP +switches of *all* of the Rocketport cards. + +The second, third, and fourth RocketPort cards require a 64-byte +contiguous block of I/O addresses, starting at one of the following +I/O addresses: 0x100h, 0x140h, 0x180h, 0x1C0h, 0x200h, 0x240h, 0x280h, +0x2C0h, 0x300h, 0x340h, 0x380h, 0x3C0h. The I/O address used by the +second, third, and fourth Rocketport cards (if present) are set via +software control. The DIP switch settings for the I/O address must be +set to the value of the first Rocketport cards. + +In order to distinguish each of the card from the others, each card +must have a unique board ID set on the dip switches. The first +Rocketport board must be set with the DIP switches corresponding to +the first board, the second board must be set with the DIP switches +corresponding to the second board, etc. IMPORTANT: The board ID is +the only place where the DIP switch settings should differ between the +various Rocketport boards in a system. + +The I/O address range used by any of the RocketPort cards must not +conflict with any other cards in the system, including other +RocketPort cards. Below, you will find a list of commonly used I/O +address ranges which may be in use by other devices in your system. +On a Linux system, "cat /proc/ioports" will also be helpful in +identifying what I/O addresses are being used by devices on your +system. + +Remember, the FIRST RocketPort uses 68 I/O addresses. So, if you set it +for 0x100, it will occupy 0x100 to 0x143. This would mean that you +CAN NOT set the second, third or fourth board for address 0x140 since +the first 4 bytes of that range are used by the first board. You would +need to set the second, third, or fourth board to one of the next available +blocks such as 0x180. + +RocketPort and RocketPort RA SW1 Settings:: + + +-------------------------------+ + | 8 | 7 | 6 | 5 | 4 | 3 | 2 | 1 | + +-------+-------+---------------+ + | Unused| Card | I/O Port Block| + +-------------------------------+ + + DIP Switches DIP Switches + 7 8 6 5 + =================== =================== + On On UNUSED, MUST BE ON. On On First Card <==== Default + On Off Second Card + Off On Third Card + Off Off Fourth Card + + DIP Switches I/O Address Range + 4 3 2 1 Used by the First Card + ===================================== + On Off On Off 100-143 + On Off Off On 140-183 + On Off Off Off 180-1C3 <==== Default + Off On On Off 200-243 + Off On Off On 240-283 + Off On Off Off 280-2C3 + Off Off On Off 300-343 + Off Off Off On 340-383 + Off Off Off Off 380-3C3 + +Reporting Bugs +-------------- + +For technical support, please provide the following +information: Driver version, kernel release, distribution of +kernel, and type of board you are using. Error messages and log +printouts port configuration details are especially helpful. + +USA: + :Phone: (612) 494-4100 + :FAX: (612) 494-4199 + :email: support@comtrol.com + +Comtrol Europe: + :Phone: +44 (0) 1 869 323-220 + :FAX: +44 (0) 1 869 323-211 + :email: support@comtrol.co.uk + +Web: http://www.comtrol.com +FTP: ftp.comtrol.com |