3 files changed, 67 insertions, 4 deletions
diff --git a/Documentation/usb/anchors.txt b/Documentation/usb/anchors.txt
index 5e6b64c20d25..6f24f566955a 100644
--- a/Documentation/usb/anchors.txt
+++ b/Documentation/usb/anchors.txt
@@ -52,6 +52,11 @@ Therefore no guarantee is made that the URBs have been unlinked when
 the call returns. They may be unlinked later but will be unlinked in
 finite time.
 
+usb_scuttle_anchored_urbs()
+---------------------------
+
+All URBs of an anchor are unanchored en masse.
+
 usb_wait_anchor_empty_timeout()
 -------------------------------
 
@@ -59,4 +64,16 @@ This function waits for all URBs associated with an anchor to finish
 or a timeout, whichever comes first. Its return value will tell you
 whether the timeout was reached.
 
+usb_anchor_empty()
+------------------
+
+Returns true if no URBs are associated with an anchor. Locking
+is the caller's responsibility.
+
+usb_get_from_anchor()
+---------------------
 
+Returns the oldest anchored URB of an anchor. The URB is unanchored
+and returned with a reference. As you may mix URBs to several
+destinations in one anchor you have no guarantee the chronologically
+first submitted URB is returned.
+\ No newline at end of file
diff --git a/Documentation/usb/misc_usbsevseg.txt b/Documentation/usb/misc_usbsevseg.txt
new file mode 100644
index 000000000000..0f6be4f9930b
--- /dev/null
+++ b/Documentation/usb/misc_usbsevseg.txt
@@ -0,0 +1,46 @@
+USB 7-Segment Numeric Display
+Manufactured by Delcom Engineering
+
+Device Information
+------------------
+USB VENDOR_ID	0x0fc5
+USB PRODUCT_ID	0x1227
+Both the 6 character and 8 character displays have PRODUCT_ID,
+and according to Delcom Engineering no queryable information
+can be obtained from the device to tell them apart.
+
+Device Modes
+------------
+By default, the driver assumes the display is only 6 characters
+The mode for 6 characters is:
+	MSB 0x06; LSB 0x3f
+For the 8 character display:
+	MSB 0x08; LSB 0xff
+The device can accept "text" either in raw, hex, or ascii textmode.
+raw controls each segment manually,
+hex expects a value between 0-15 per character,
+ascii expects a value between '0'-'9' and 'A'-'F'.
+The default is ascii.
+
+Device Operation
+----------------
+1.	Turn on the device:
+	echo 1 > /sys/bus/usb/.../powered
+2.	Set the device's mode:
+	echo $mode_msb > /sys/bus/usb/.../mode_msb
+	echo $mode_lsb > /sys/bus/usb/.../mode_lsb
+3.	Set the textmode:
+	echo $textmode > /sys/bus/usb/.../textmode
+4.	set the text (for example):
+	echo "123ABC" > /sys/bus/usb/.../text (ascii)
+	echo "A1B2" > /sys/bus/usb/.../text (ascii)
+	echo -ne "\x01\x02\x03" > /sys/bus/usb/.../text (hex)
+5.	Set the decimal places.
+	The device has either 6 or 8 decimal points.
+	to set the nth decimal place calculate 10 ** n
+	and echo it in to /sys/bus/usb/.../decimals
+	To set multiple decimals points sum up each power.
+	For example, to set the 0th and 3rd decimal place
+	echo 1001 > /sys/bus/usb/.../decimals
+
+
diff --git a/Documentation/usb/power-management.txt b/Documentation/usb/power-management.txt
index 9d31140e3f5b..e48ea1d51010 100644
--- a/Documentation/usb/power-management.txt
+++ b/Documentation/usb/power-management.txt
@@ -350,12 +350,12 @@ without holding the mutex.
 
 There also are a couple of utility routines drivers can use:
 
-	usb_autopm_enable() sets pm_usage_cnt to 1 and then calls
-	usb_autopm_set_interface(), which will attempt an autoresume.
-
-	usb_autopm_disable() sets pm_usage_cnt to 0 and then calls
+	usb_autopm_enable() sets pm_usage_cnt to 0 and then calls
 	usb_autopm_set_interface(), which will attempt an autosuspend.
 
+	usb_autopm_disable() sets pm_usage_cnt to 1 and then calls
+	usb_autopm_set_interface(), which will attempt an autoresume.
+
 The conventional usage pattern is that a driver calls
 usb_autopm_get_interface() in its open routine and
 usb_autopm_put_interface() in its close or release routine.  But