| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the early assembler page table code assumes that precisely
1xpgd, 1xpud, 1xpmd are sufficient to represent the early kernel text
mappings.
Unfortunately this is rarely the case when running with a 16KB granule,
and we also run into limits with 4KB granule when building much larger
kernels.
This patch re-writes the early page table logic to compute indices of
mappings for each level of page table, and if multiple indices are
required, the next-level page table is scaled up accordingly.
Also the required size of the swapper_pg_dir is computed at link time
to cover the mapping [KIMAGE_ADDR + VOFFSET, _end]. When KASLR is
enabled, an extra page is set aside for each level that may require extra
entries at runtime.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The trampoline page tables are positioned after the early page tables in
the kernel linker script.
As we are about to change the early page table logic to resolve the
swapper size at link time as opposed to compile time, the
SWAPPER_DIR_SIZE variable (currently used to locate the trampline)
will be rendered unsuitable for low level assembler.
This patch solves this issue by moving the trampoline before the PAN
page tables. The offset to the trampoline from ttbr1 can then be
expressed by: PAGE_SIZE + RESERVED_TTBR0_SIZE, which is available to the
entry assembler.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently one resolves the location of the reserved_ttbr0 for PAN by
taking a positive offset from swapper_pg_dir. In a future patch we wish
to extend the swapper s.t. its size is determined at link time rather
than comile time, rendering SWAPPER_DIR_SIZE unsuitable for such a low
level calculation.
In this patch we re-arrange the order of the linker script s.t. instead
one computes reserved_ttbr0 by subtracting RESERVED_TTBR0_SIZE from
swapper_pg_dir.
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The literal pool entry for identifying the vectors base is the only piece
of information in the trampoline page that identifies the true location
of the kernel.
This patch moves it into a page-aligned region of the .rodata section
and maps this adjacent to the trampoline text via an additional fixmap
entry, which protects against any accidental leakage of the trampoline
contents.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To allow unmapping of the kernel whilst running at EL0, we need to
point the exception vectors at an entry trampoline that can map/unmap
the kernel on entry/exit respectively.
This patch adds the trampoline page, although it is not yet plugged
into the vector table and is therefore unused.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Tested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch enables arm64 to be built with vmap'd task and IRQ stacks.
As vmap'd stacks are mapped at page granularity, stacks must be a multiple of
PAGE_SIZE. This means that a 64K page kernel must use stacks of at least 64K in
size.
To minimize the increase in Image size, IRQ stacks are dynamically allocated at
boot time, rather than embedding the boot CPU's IRQ stack in the kernel image.
This patch was co-authored by Ard Biesheuvel and Mark Rutland.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently we define SEGMENT_ALIGN directly in our vmlinux.lds.S.
This is unfortunate, as the EFI stub currently open-codes the same
number, and in future we'll want to fiddle with this.
This patch moves the definition to our <asm/memory.h>, where it can be
used by both vmlinux.lds.S and the EFI stub code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Tested-by: Laura Abbott <labbott@redhat.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To prevent unintended modifications to the kernel text (malicious or
otherwise) while running the EFI stub, describe the kernel image as
two separate sections: a .text section with read-execute permissions,
covering .text, .rodata and .init.text, and a .data section with
read-write permissions, covering .init.data, .data and .bss.
This relies on the firmware to actually take the section permission
flags into account, but this is something that is currently being
implemented in EDK2, which means we will likely start seeing it in
the wild between one and two years from now.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To avoid having mappings that are writable and executable at the same
time, split the init region into a .init.text region that is mapped
read-only, and a .init.data region that is mapped non-executable.
This is possible now that the alternative patching occurs via the linear
mapping, and the linear alias of the init region is always mapped writable
(but never executable).
Since the alternatives descriptions themselves are read-only data, move
those into the .init.text region.
Reviewed-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch adds the uaccess macros/functions to disable access to user
space by setting TTBR0_EL1 to a reserved zeroed page. Since the value
written to TTBR0_EL1 must be a physical address, for simplicity this
patch introduces a reserved_ttbr0 page at a constant offset from
swapper_pg_dir. The uaccess_disable code uses the ttbr1_el1 value
adjusted by the reserved_ttbr0 offset.
Enabling access to user is done by restoring TTBR0_EL1 with the value
from the struct thread_info ttbr0 variable. Interrupts must be disabled
during the uaccess_ttbr0_enable code to ensure the atomicity of the
thread_info.ttbr0 read and TTBR0_EL1 write. This patch also moves the
get_thread_info asm macro from entry.S to assembler.h for reuse in the
uaccess_ttbr0_* macros.
Cc: Will Deacon <will.deacon@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Resume from hibernate needs to clean any text executed by the kernel with
the MMU off to the PoC. Collect these functions together into the
.idmap.text section as all this code is tightly coupled and also needs
the same cleaning after resume.
Data is more complicated, secondary_holding_pen_release is written with
the MMU on, clean and invalidated, then read with the MMU off. In contrast
__boot_cpu_mode is written with the MMU off, the corresponding cache line
is invalidated, so when we read it with the MMU on we don't get stale data.
These cache maintenance operations conflict with each other if the values
are within a Cache Writeback Granule (CWG) of each other.
Collect the data into two sections .mmuoff.data.read and .mmuoff.data.write,
the linker script ensures mmuoff.data.write section is aligned to the
architectural maximum CWG of 2KB.
Signed-off-by: James Morse <james.morse@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The linker routines that we rely on to produce a relocatable PIE binary
treat it as a shared ELF object in some ways, i.e., it emits symbol based
R_AARCH64_ABS64 relocations into the final binary since doing so would be
appropriate when linking a shared library that is subject to symbol
preemption. (This means that an executable can override certain symbols
that are exported by a shared library it is linked with, and that the
shared library *must* update all its internal references as well, and point
them to the version provided by the executable.)
Symbol preemption does not occur for OS hosted PIE executables, let alone
for vmlinux, and so we would prefer to get rid of these symbol based
relocations. This would allow us to simplify the relocation routines, and
to strip the .dynsym, .dynstr and .hash sections from the binary. (Note
that these are tiny, and are placed in the .init segment, but they clutter
up the vmlinux binary.)
Note that these R_AARCH64_ABS64 relocations are only emitted for absolute
references to symbols defined in the linker script, all other relocatable
quantities are covered by anonymous R_AARCH64_RELATIVE relocations that
simply list the offsets to all 64-bit values in the binary that need to be
fixed up based on the offset between the link time and run time addresses.
Fortunately, GNU ld has a -Bsymbolic option, which is intended for shared
libraries to allow them to ignore symbol preemption, and unconditionally
bind all internal symbol references to its own definitions. So set it for
our PIE binary as well, and get rid of the asoociated sections and the
relocation code that processes them.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: fixed conflict with __dynsym_offset linker script entry]
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Due to the untyped KIMAGE_VADDR constant, the linker may not notice
that the __rela_offset and __dynsym_offset expressions are absolute
values (i.e., are not subject to relocation). This does not matter for
KASLR, but it does confuse kallsyms in relative mode, since it uses
the lowest non-absolute symbol address as the anchor point, and expects
all other symbol addresses to be within 4 GB of it.
Fix this by qualifying these expressions as ABSOLUTE() explicitly.
Fixes: 0cd3defe0af4 ("arm64: kernel: perform relocation processing from ID map")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
* kprobes:
arm64: kprobes: Add KASAN instrumentation around stack accesses
arm64: kprobes: Cleanup jprobe_return
arm64: kprobes: Fix overflow when saving stack
arm64: kprobes: WARN if attempting to step with PSTATE.D=1
kprobes: Add arm64 case in kprobe example module
arm64: Add kernel return probes support (kretprobes)
arm64: Add trampoline code for kretprobes
arm64: kprobes instruction simulation support
arm64: Treat all entry code as non-kprobe-able
arm64: Blacklist non-kprobe-able symbol
arm64: Kprobes with single stepping support
arm64: add conditional instruction simulation support
arm64: Add more test functions to insn.c
arm64: Add HAVE_REGS_AND_STACK_ACCESS_API feature
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Entry symbols are not kprobe safe. So blacklist them for kprobing.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
[catalin.marinas@arm.com: Do not include syscall wrappers in .entry.text]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add support for basic kernel probes(kprobes) and jump probes
(jprobes) for ARM64.
Kprobes utilizes software breakpoint and single step debug
exceptions supported on ARM v8.
A software breakpoint is placed at the probe address to trap the
kernel execution into the kprobe handler.
ARM v8 supports enabling single stepping before the break exception
return (ERET), with next PC in exception return address (ELR_EL1). The
kprobe handler prepares an executable memory slot for out-of-line
execution with a copy of the original instruction being probed, and
enables single stepping. The PC is set to the out-of-line slot address
before the ERET. With this scheme, the instruction is executed with the
exact same register context except for the PC (and DAIF) registers.
Debug mask (PSTATE.D) is enabled only when single stepping a recursive
kprobe, e.g.: during kprobes reenter so that probed instruction can be
single stepped within the kprobe handler -exception- context.
The recursion depth of kprobe is always 2, i.e. upon probe re-entry,
any further re-entry is prevented by not calling handlers and the case
counted as a missed kprobe).
Single stepping from the x-o-l slot has a drawback for PC-relative accesses
like branching and symbolic literals access as the offset from the new PC
(slot address) may not be ensured to fit in the immediate value of
the opcode. Such instructions need simulation, so reject
probing them.
Instructions generating exceptions or cpu mode change are rejected
for probing.
Exclusive load/store instructions are rejected too. Additionally, the
code is checked to see if it is inside an exclusive load/store sequence
(code from Pratyush).
System instructions are mostly enabled for stepping, except MSR/MRS
accesses to "DAIF" flags in PSTATE, which are not safe for
probing.
This also changes arch/arm64/include/asm/ptrace.h to use
include/asm-generic/ptrace.h.
Thanks to Steve Capper and Pratyush Anand for several suggested
Changes.
Signed-off-by: Sandeepa Prabhu <sandeepa.s.prabhu@gmail.com>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As Kees Cook notes in the ARM counterpart of this patch [0]:
The _etext position is defined to be the end of the kernel text code,
and should not include any part of the data segments. This interferes
with things that might check memory ranges and expect executable code
up to _etext.
In particular, Kees is referring to the HARDENED_USERCOPY patch set [1],
which rejects attempts to call copy_to_user() on kernel ranges containing
executable code, but does allow access to the .rodata segment. Regardless
of whether one may or may not agree with the distinction, it makes sense
for _etext to have the same meaning across architectures.
So let's put _etext where it belongs, between .text and .rodata, and fix
up existing references to use __init_begin instead, which unlike _end_rodata
includes the exception and notes sections as well.
The _etext references in kaslr.c are left untouched, since its references
to [_stext, _etext) are meant to capture potential jump instruction targets,
and so disregarding .rodata is actually an improvement here.
[0] http://article.gmane.org/gmane.linux.kernel/2245084
[1] http://thread.gmane.org/gmane.linux.kernel.hardened.devel/2502
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add support for hibernate/suspend-to-disk.
Suspend borrows code from cpu_suspend() to write cpu state onto the stack,
before calling swsusp_save() to save the memory image.
Restore creates a set of temporary page tables, covering only the
linear map, copies the restore code to a 'safe' page, then uses the copy to
restore the memory image. The copied code executes in the lower half of the
address space, and once complete, restores the original kernel's page
tables. It then calls into cpu_resume(), and follows the normal
cpu_suspend() path back into the suspend code.
To restore a kernel using KASLR, the address of the page tables, and
cpu_resume() are stored in the hibernate arch-header and the el2
vectors are pivotted via the 'safe' page in low memory.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Kevin Hilman <khilman@baylibre.com> # Tested on Juno R2
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Refactor the relocation processing so that the code executes from the
ID map while accessing the relocation tables via the virtual mapping.
This way, we can use literals containing virtual addresses as before,
instead of having to use convoluted absolute expressions.
For symmetry with the secondary code path, the relocation code and the
subsequent jump to the virtual entry point are implemented in a function
called __primary_switch(), and __mmap_switched() is renamed to
__primary_switched(). Also, the call sequence in stext() is aligned with
the one in secondary_startup(), by replacing the awkward 'adr_l lr' and
'b cpu_setup' sequence with a simple branch and link.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The mapping of the kernel consist of four segments, each of which is mapped
with different permission attributes and/or lifetimes. To optimize the TLB
and translation table footprint, we define various opaque constants in the
linker script that resolve to different aligment values depending on the
page size and whether CONFIG_DEBUG_ALIGN_RODATA is set.
Considering that
- a 4 KB granule kernel benefits from a 64 KB segment alignment (due to
the fact that it allows the use of the contiguous bit),
- the minimum alignment of the .data segment is THREAD_SIZE already, not
PAGE_SIZE (i.e., we already have padding between _data and the start of
the .data payload in many cases),
- 2 MB is a suitable alignment value on all granule sizes, either for
mapping directly (level 2 on 4 KB), or via the contiguous bit (level 3 on
16 KB and 64 KB),
- anything beyond 2 MB exceeds the minimum alignment mandated by the boot
protocol, and can only be mapped efficiently if the physical alignment
happens to be the same,
we can simplify this by standardizing on 64 KB (or 2 MB) explicitly, i.e.,
regardless of granule size, all segments are aligned either to 64 KB, or to
2 MB if CONFIG_DEBUG_ALIGN_RODATA=y. This also means we can drop the Kconfig
dependency of CONFIG_DEBUG_ALIGN_RODATA on CONFIG_ARM64_4K_PAGES.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Keeping .head.text out of the .text mapping buys us very little: its actual
payload is only 4 KB, most of which is padding, but the page alignment may
add up to 2 MB (in case of CONFIG_DEBUG_ALIGN_RODATA=y) of additional
padding to the uncompressed kernel Image.
Also, on 4 KB granule kernels, the 4 KB misalignment of .text forces us to
map the adjacent 56 KB of code without the PTE_CONT attribute, and since
this region contains things like the vector table and the GIC interrupt
handling entry point, this region is likely to benefit from the reduced TLB
pressure that results from PTE_CONT mappings.
So remove the alignment between the .head.text and .text sections, and use
the [_text, _etext) rather than the [_stext, _etext) interval for mapping
the .text segment.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The main changes are:
- Use separate EFI page tables when executing EFI firmware code.
This isolates the EFI context from the rest of the kernel, which
has security and general robustness advantages. (Matt Fleming)
- Run regular UEFI firmware with interrupts enabled. This is already
the status quo under other OSs. (Ard Biesheuvel)
- Various x86 EFI enhancements, such as the use of non-executable
attributes for EFI memory mappings. (Sai Praneeth Prakhya)
- Various arm64 UEFI enhancements. (Ard Biesheuvel)
- ... various fixes and cleanups.
The separate EFI page tables feature got delayed twice already,
because it's an intrusive change and we didn't feel confident about
it - third time's the charm we hope!"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (37 commits)
x86/mm/pat: Fix boot crash when 1GB pages are not supported by the CPU
x86/efi: Only map kernel text for EFI mixed mode
x86/efi: Map EFI_MEMORY_{XP,RO} memory region bits to EFI page tables
x86/mm/pat: Don't implicitly allow _PAGE_RW in kernel_map_pages_in_pgd()
efi/arm*: Perform hardware compatibility check
efi/arm64: Check for h/w support before booting a >4 KB granular kernel
efi/arm: Check for LPAE support before booting a LPAE kernel
efi/arm-init: Use read-only early mappings
efi/efistub: Prevent __init annotations from being used
arm64/vmlinux.lds.S: Handle .init.rodata.xxx and .init.bss sections
efi/arm64: Drop __init annotation from handle_kernel_image()
x86/mm/pat: Use _PAGE_GLOBAL bit for EFI page table mappings
efi/runtime-wrappers: Run UEFI Runtime Services with interrupts enabled
efi: Reformat GUID tables to follow the format in UEFI spec
efi: Add Persistent Memory type name
efi: Add NV memory attribute
x86/efi: Show actual ending addresses in efi_print_memmap
x86/efi/bgrt: Don't ignore the BGRT if the 'valid' bit is 0
efivars: Use to_efivar_entry
efi: Runtime-wrapper: Get rid of the rtc_lock spinlock
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The EFI stub is typically built into the decompressor (x86, ARM) so none
of its symbols are annotated as __init. However, on arm64, the stub is
linked into the kernel proper, and the code is __init annotated at the
section level by prepending all names of SHF_ALLOC sections with '.init'.
This results in section names like .init.rodata.str1.8 (for string literals)
and .init.bss (which is tiny), both of which can be moved into the .init.data
output section.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1455712566-16727-6-git-send-email-matt@codeblueprint.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently the .rodata section is actually still executable when DEBUG_RODATA
is enabled. This changes that so the .rodata is actually read only, no execute.
It also adds the .rodata section to the mem_init banner.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: added vm_struct vmlinux_rodata in map_kernel()]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This implements CONFIG_RELOCATABLE, which links the final vmlinux
image with a dynamic relocation section, allowing the early boot code
to perform a relocation to a different virtual address at runtime.
This is a prerequisite for KASLR (CONFIG_RANDOMIZE_BASE).
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This introduces the preprocessor symbol KIMAGE_VADDR which will serve as
the symbolic virtual base of the kernel region, i.e., the kernel's virtual
offset will be KIMAGE_VADDR + TEXT_OFFSET. For now, we define it as being
equal to PAGE_OFFSET, but in the future, it will be moved below it once
we move the kernel virtual mapping out of the linear mapping.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently we have separate ALIGN_DEBUG_RO{,_MIN} directives to align
_etext and __init_begin. While we ensure that __init_begin is
page-aligned, we do not provide the same guarantee for _etext. This is
not problematic currently as the alignment of __init_begin is sufficient
to prevent issues when we modify permissions.
Subsequent patches will assume page alignment of segments of the kernel
we wish to map with different permissions. To ensure this, move _etext
after the ALIGN_DEBUG_RO_MIN for the init section. This renders the
prior ALIGN_DEBUG_RO irrelevant, and hence it is removed. Likewise,
upgrade to ALIGN_DEBUG_RO_MIN(PAGE_SIZE) for _stext.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
"Here is the core arm64 queue for 4.5. As you might expect, the
Christmas break resulted in a number of patches not making the final
cut, so 4.6 is likely to be larger than usual. There's still some
useful stuff here, however, and it's detailed below.
The EFI changes have been Reviewed-by Matt and the memblock change got
an "OK" from akpm.
Summary:
- Support for a separate IRQ stack, although we haven't reduced the
size of our thread stack just yet since we don't have enough data
to determine a safe value
- Refactoring of our EFI initialisation and runtime code into
drivers/firmware/efi/ so that it can be reused by arch/arm/.
- Ftrace improvements when unwinding in the function graph tracer
- Document our silicon errata handling process
- Cache flushing optimisation when mapping executable pages
- Support for hugetlb mappings using the contiguous hint in the pte"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (45 commits)
arm64: head.S: use memset to clear BSS
efi: stub: define DISABLE_BRANCH_PROFILING for all architectures
arm64: entry: remove pointless SPSR mode check
arm64: mm: move pgd_cache initialisation to pgtable_cache_init
arm64: module: avoid undefined shift behavior in reloc_data()
arm64: module: fix relocation of movz instruction with negative immediate
arm64: traps: address fallout from printk -> pr_* conversion
arm64: ftrace: fix a stack tracer's output under function graph tracer
arm64: pass a task parameter to unwind_frame()
arm64: ftrace: modify a stack frame in a safe way
arm64: remove irq_count and do_softirq_own_stack()
arm64: hugetlb: add support for PTE contiguous bit
arm64: Use PoU cache instr for I/D coherency
arm64: Defer dcache flush in __cpu_copy_user_page
arm64: reduce stack use in irq_handler
arm64: mm: ensure that the zero page is visible to the page table walker
arm64: Documentation: add list of software workarounds for errata
arm64: mm: place __cpu_setup in .text
arm64: cmpxchg: Don't incldue linux/mmdebug.h
arm64: mm: fold alternatives into .init
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently we treat the alternatives separately from other data that's
only used during initialisation, using separate .altinstructions and
.altinstr_replacement linker sections. These are freed for general
allocation separately from .init*. This is problematic as:
* We do not remove execute permissions, as we do for .init, leaving the
memory executable.
* We pad between them, making the kernel Image bianry up to PAGE_SIZE
bytes larger than necessary.
This patch moves the two sections into the contiguous region used for
.init*. This saves some memory, ensures that we remove execute
permissions, and allows us to remove some code made redundant by this
reorganisation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently we place an ALIGN_DEBUG_RO between text and data for the .text
and .init sections, and depending on configuration each of these may
result in up to SECTION_SIZE bytes worth of padding (for
DEBUG_RODATA_ALIGN).
We make no distinction between the text and data in each of these
sections at any point when creating the initial page tables in head.S.
We also make no distinction when modifying the tables; __map_memblock,
fixup_executable, mark_rodata_ro, and fixup_init only work at section
granularity. Thus this padding is unnecessary.
For the spit between init text and data we impose a minimum alignment of
16 bytes, but this is also unnecessary. The init data is output
immediately after the padding before any symbols are defined, so this is
not required to keep a symbol for linker a section array correctly
associated with the data. Any objects within the section will be given
at least their usual alignment regardless.
This patch removes the redundant padding.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Jeremy Linton <jeremy.linton@arm.com>
Cc: Laura Abbott <labbott@fedoraproject.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|/
|
|
|
|
|
|
|
|
|
| |
Bring the linker script in line with the recent increase of
L1_CACHE_BYTES to 128. Replace the hardcoded value of 64 with the
symbolic constant.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
[catalin.marinas@arm.com: fix up RW_DATA_SECTION as well]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A kernel built with DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA doesn't
have .text aligned to a page boundary, though fixup_executable works at
page-granularity thanks to its use of create_mapping. If .text is not
page-aligned, the first page it exists in may be marked non-executable,
leading to failures when an attempt is made to execute code in said
page.
This patch upgrades ALIGN_DEBUG_RO and ALIGN_DEBUG_RO_MIN to force page
alignment for DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA kernels,
ensuring that all sections with specific RWX permission requirements are
mapped with the correct permissions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Laura Abbott <laura@labbott.name>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Fixes: da141706aea52c1a ("arm64: add better page protections to arm64")
Cc: <stable@vger.kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Move the kernel pagetable (both swapper and idmap) definitions
from the generic asm/page.h to a new file, asm/kernel-pgtable.h.
This is mostly a cosmetic change, to clean up the asm/page.h to
get rid of the arch specific details which are not needed by the
generic code.
Also renames the symbols to prevent conflicts. e.g,
BLOCK_SHIFT => SWAPPER_BLOCK_SHIFT
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Commit ea8c2e112445 ("arm64: Extend the idmap to the whole kernel
image") changed the early page table code so that the entire kernel
Image is covered by the identity map. This allows functions that
need to enable or disable the MMU to reside anywhere in the kernel
Image.
However, this change has the unfortunate side effect that the Image
cannot cross a physical 512 MB alignment boundary anymore, since the
early page table code cannot deal with the Image crossing a /virtual/
512 MB alignment boundary.
So instead, reduce the ID map to a single page, that is populated by
the contents of the .idmap.text section. Only three functions reside
there at the moment: __enable_mmu(), cpu_resume_mmu() and cpu_reset().
If new code is introduced that needs to manipulate the MMU state, it
should be added to this section as well.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The HYP init bounce page is a runtime construct that ensures that the
HYP init code does not cross a page boundary. However, this is something
we can do perfectly well at build time, by aligning the code appropriately.
For arm64, we just align to 4 KB, and enforce that the code size is less
than 4 KB, regardless of the chosen page size.
For ARM, the whole code is less than 256 bytes, so we tweak the linker
script to align at a power of 2 upper bound of the code size
Note that this also fixes a benign off-by-one error in the original bounce
page code, where a bounce page would be allocated unnecessarily if the code
was exactly 1 page in size.
On ARM, it also fixes an issue with very large kernels reported by Arnd
Bergmann, where stub sections with linker emitted veneers could erroneously
trigger the size/alignment ASSERT() in the linker script.
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add page protections for arm64 similar to those in arm.
This is for security reasons to prevent certain classes
of exploits. The current method:
- Map all memory as either RWX or RW. We round to the nearest
section to avoid creating page tables before everything is mapped
- Once everything is mapped, if either end of the RWX section should
not be X, we split the PMD and remap as necessary
- When initmem is to be freed, we change the permissions back to
RW (using stop machine if necessary to flush the TLB)
- If CONFIG_DEBUG_RODATA is set, the read only sections are set
read only.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
.exit.* sections may be subject to patching by the new alternatives
framework and so shouldn't be discarded at link-time. Without this patch,
such a section will result in the following linker error:
`.exit.text' referenced in section `.altinstructions' of
drivers/built-in.o: defined in discarded section `.exit.text' of
drivers/built-in.o
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
| |
With a blatant copy of some x86 bits we introduce the alternative
runtime patching "framework" to arm64.
This is quite basic for now and we only provide the functions we need
at this time.
This is connected to the newly introduced feature bits.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Change our PE/COFF header to use the minimum file alignment of
512 bytes (0x200), as mandated by the PE/COFF spec v8.3
Also update the linker script so that the Image file itself is also a
round multiple of FileAlignment.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch changes the __init_end address to a
page align address, so that free_initmem() can
free the whole .init section, because if the end
address is not page aligned, it will round down to
a page align address, then the tail unligned page
will not be freed.
Signed-off-by: wang <yalin.wang2010@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The arm64 Image header contains a text_offset field which bootloaders
are supposed to read to determine the offset (from a 2MB aligned "start
of memory" per booting.txt) at which to load the kernel. The offset is
not well respected by bootloaders at present, and due to the lack of
variation there is little incentive to support it. This is unfortunate
for the sake of future kernels where we may wish to vary the text offset
(even zeroing it).
This patch adds options to arm64 to enable fuzz-testing of text_offset.
CONFIG_ARM64_RANDOMIZE_TEXT_OFFSET forces the text offset to a random
16-byte aligned value value in the range [0..2MB) upon a build of the
kernel. It is recommended that distribution kernels enable randomization
to test bootloaders such that any compliance issues can be fixed early.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently the kernel Image is stripped of everything past the initial
stack, and at runtime the memory is initialised and used by the kernel.
This makes the effective minimum memory footprint of the kernel larger
than the size of the loaded binary, though bootloaders have no mechanism
to identify how large this minimum memory footprint is. This makes it
difficult to choose safe locations to place both the kernel and other
binaries required at boot (DTB, initrd, etc), such that the kernel won't
clobber said binaries or other reserved memory during initialisation.
Additionally when big endian support was added the image load offset was
overlooked, and is currently of an arbitrary endianness, which makes it
difficult for bootloaders to make use of it. It seems that bootloaders
aren't respecting the image load offset at present anyway, and are
assuming that offset 0x80000 will always be correct.
This patch adds an effective image size to the kernel header which
describes the amount of memory from the start of the kernel Image binary
which the kernel expects to use before detecting memory and handling any
memory reservations. This can be used by bootloaders to choose suitable
locations to load the kernel and/or other binaries such that the kernel
will not clobber any memory unexpectedly. As before, memory reservations
are required to prevent the kernel from clobbering these locations
later.
Both the image load offset and the effective image size are forced to be
little-endian regardless of the native endianness of the kernel to
enable bootloaders to load a kernel of arbitrary endianness. Bootloaders
which wish to make use of the load offset can inspect the effective
image size field for a non-zero value to determine if the offset is of a
known endianness. To enable software to determine the endinanness of the
kernel as may be required for certain use-cases, a new flags field (also
little-endian) is added to the kernel header to export this information.
The documentation is updated to clarify these details. To discourage
future assumptions regarding the value of text_offset, the value at this
point in time is removed from the main flow of the documentation (though
kept as a compatibility note). Some minor formatting issues in the
documentation are also corrected.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Tom Rini <trini@ti.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Kevin Hilman <kevin.hilman@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently we place swapper_pg_dir and idmap_pg_dir below the kernel
image, between PHYS_OFFSET and (PHYS_OFFSET + TEXT_OFFSET). However,
bootloaders may use portions of this memory below the kernel and we do
not parse the memory reservation list until after the MMU has been
enabled. As such we may clobber some memory a bootloader wishes to have
preserved.
To enable the use of all of this memory by bootloaders (when the
required memory reservations are communicated to the kernel) it is
necessary to move our initial page tables elsewhere. As we currently
have an effectively unbound requirement for memory at the end of the
kernel image for .bss, we can place the page tables here.
This patch moves the initial page table to the end of the kernel image,
after the BSS. As they do not consist of any initialised data they will
be stripped from the kernel Image as with the BSS. The BSS clearing
routine is updated to stop at __bss_stop rather than _end so as to not
clobber the page tables, and memory reservations made redundant by the
new organisation are removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Change the arm64 linker script ENTRY() command to define _text as the
kernel entry point.
The arm64 boot protocol specifies that the kernel must be entered at the
beginning of the kernel image. The existing ENTRY() command defined the
symbol stext as the entry point, which emitted an incorrect entry point,
but would not cause a runtime error because the existing entry code
immediately jumps to stext.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
| |
The __data_loc variable is an unused left over from the 32 bit arm implementation.
Remove that variable and adjust the __mmap_switched startup routine accordingly.
Signed-off-by: Geoff Levand <geoff@infradead.org> for Huawei, Linaro
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
| |
We currently try to emit .comment twice, once in STABS_DEBUG, and once
in the line immediately following it. As the two section definitions are
identical, the latter is redundant and can be dropped.
This patch drops the redundant .comment section definition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
The .data section in the arm64 linker script currently lacks a
definition for page-aligned data. This leads to a .page_aligned
section being placed between the end of data and start of bss.
This patch corrects that by using the generic RW_DATA_SECTION
macro which includes support for page-aligned data.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|