From 64cf50d0c8d16679faf24864cff8bbe95c08f116 Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Wed, 20 Mar 2019 18:48:01 +0530 Subject: arm64: dts: qcom: qcs404: Add tsens controller qcs404 has a single TSENS IP block with 10 sensors. The calibration data is stored in an eeprom (qfprom) that is accessed through the nvmem framework. We add the qfprom node to allow the tsens sensors to be calibrated correctly. Signed-off-by: Amit Kucheria Signed-off-by: Andy Gross --- arch/arm64/boot/dts/qcom/qcs404.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi index 3f17e1b09c13..4e5fe3f12f4b 100644 --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi @@ -251,6 +251,16 @@ reg = <0x00060000 0x6000>; }; + qfprom: qfprom@a4000 { + compatible = "qcom,qfprom"; + reg = <0x000a4000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + tsens_caldata: caldata@d0 { + reg = <0x1f8 0x14>; + }; + }; + rng: rng@e3000 { compatible = "qcom,prng-ee"; reg = <0x000e3000 0x1000>; @@ -258,6 +268,16 @@ clock-names = "core"; }; + tsens: thermal-sensor@4a9000 { + compatible = "qcom,qcs404-tsens", "qcom,tsens-v1"; + reg = <0x004a9000 0x1000>, /* TM */ + <0x004a8000 0x1000>; /* SROT */ + nvmem-cells = <&tsens_caldata>; + nvmem-cell-names = "calib"; + #qcom,sensors = <10>; + #thermal-sensor-cells = <1>; + }; + remoteproc_cdsp: remoteproc@b00000 { compatible = "qcom,qcs404-cdsp-pas"; reg = <0x00b00000 0x4040>; -- cgit v1.2.3 From f48cee3239a16a2ecf7e20bee485ae1b25d0deec Mon Sep 17 00:00:00 2001 From: Amit Kucheria Date: Wed, 20 Mar 2019 18:48:02 +0530 Subject: arm64: dts: qcom: qcs404: Add thermal zones for each sensor qcs404 has 10 sensors connected to the single TSENS IP. Define a thermal zone for each of those sensors to expose the temperature of each zone. Signed-off-by: Amit Kucheria Signed-off-by: Andy Gross --- arch/arm64/boot/dts/qcom/qcs404.dtsi | 252 +++++++++++++++++++++++++++++++++++ 1 file changed, 252 insertions(+) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi index 4e5fe3f12f4b..01a51f381850 100644 --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi @@ -6,6 +6,7 @@ #include #include #include +#include / { interrupt-parent = <&intc>; @@ -34,6 +35,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; + #cooling-cells= <2>; }; CPU1: cpu@101 { @@ -43,6 +45,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; + #cooling-cells= <2>; }; CPU2: cpu@102 { @@ -52,6 +55,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; + #cooling-cells= <2>; }; CPU3: cpu@103 { @@ -61,6 +65,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; + #cooling-cells= <2>; }; L2_0: l2-cache { @@ -1063,4 +1068,251 @@ #interrupt-cells = <2>; }; }; + + thermal-zones { + aoss-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 0>; + + trips { + aoss_alert0: trip-point@0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + q6-hvx-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 1>; + + trips { + q6_hvx_alert0: trip-point@0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + lpass-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 2>; + + trips { + lpass_alert0: trip-point@0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + wlan-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 3>; + + trips { + wlan_alert0: trip-point@0 { + temperature = <105000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + cluster-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 4>; + + trips { + cluster_alert0: trip-point@0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cluster_alert1: trip-point@1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cluster_crit: cluster_crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cluster_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu0-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 5>; + + trips { + cpu0_alert0: trip-point@0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu0_alert1: trip-point@1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu0_crit: cpu_crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu0_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu1-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 6>; + + trips { + cpu1_alert0: trip-point@0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu1_alert1: trip-point@1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu1_crit: cpu_crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu1_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu2-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 7>; + + trips { + cpu2_alert0: trip-point@0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu2_alert1: trip-point@1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu2_crit: cpu_crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu2_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + cpu3-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 8>; + + trips { + cpu3_alert0: trip-point@0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + cpu3_alert1: trip-point@1 { + temperature = <105000>; + hysteresis = <2000>; + type = "passive"; + }; + cpu3_crit: cpu_crit { + temperature = <120000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + cooling-maps { + map0 { + trip = <&cpu3_alert1>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + + gpu-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + + thermal-sensors = <&tsens 9>; + + trips { + gpu_alert0: trip-point@0 { + temperature = <95000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + }; }; -- cgit v1.2.3 From 79e7739f7b877d05de8f162a3ae8006657436df0 Mon Sep 17 00:00:00 2001 From: Rob Clark Date: Thu, 16 May 2019 18:52:46 -0700 Subject: arm64: dts: qcom: sdm845-cheza: add initial cheza dt This is essentialy a squash of a bunch of history of cheza dt updates from chromium kernel, some of which were themselves squashes of history from older chromium kernels. I don't claim any credit other than wanting to more easily boot upstream kernel on cheza to have an easier way to test upstream driver work ;-) I've added below in Cc tags all the original actual authors (apologies if I missed any). Cc: Douglas Anderson Cc: Sibi Sankar Cc: Evan Green Cc: Matthias Kaehlcke Cc: Abhinav Kumar Cc: Brian Norris Cc: Venkat Gopalakrishnan Cc: Rajendra Nayak Signed-off-by: Rob Clark Reviewed-by: Douglas Anderson Signed-off-by: Andy Gross --- arch/arm64/boot/dts/qcom/Makefile | 3 + arch/arm64/boot/dts/qcom/sdm845-cheza-r1.dts | 238 +++++ arch/arm64/boot/dts/qcom/sdm845-cheza-r2.dts | 238 +++++ arch/arm64/boot/dts/qcom/sdm845-cheza-r3.dts | 174 ++++ arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi | 1326 ++++++++++++++++++++++++++ 5 files changed, 1979 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-cheza-r1.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-cheza-r2.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-cheza-r3.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index b3fe72ff2955..0a7e5dfce6f7 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -7,6 +7,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r1.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza-r1.dts b/arch/arm64/boot/dts/qcom/sdm845-cheza-r1.dts new file mode 100644 index 000000000000..bd7c25bb8d35 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-cheza-r1.dts @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Cheza board device tree source + * + * Copyright 2018 Google LLC. + */ + +/dts-v1/; + +#include "sdm845-cheza.dtsi" + +/ { + model = "Google Cheza (rev1)"; + compatible = "google,cheza-rev1", "qcom,sdm845"; + + /* + * FIXED REGULATORS (not in sdm845-cheza.dtsi) - parents above children + */ + + /* + * NOTE: Technically pp3500_a is not the exact same signal as + * pp3500_a_vbob (there's a load switch between them and the EC can + * control pp3500_a via "en_pp3300_a"), but from the AP's point of + * view they are the same. + */ + pp3500_a: + pp3500_a_vbob: pp3500-a-vbob-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_bob"; + + /* + * Comes on automatically when pp5000_ldo comes on, which + * comes on automatically when ppvar_sys comes on + */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3500000>; + regulator-max-microvolt = <3500000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_dx_edp: pp3300-dx-edp-regulator { + /* Yes, it's really 3.5 despite the name of the signal */ + regulator-min-microvolt = <3500000>; + regulator-max-microvolt = <3500000>; + + vin-supply = <&pp3500_a>; + }; +}; + +/* FIXED REGULATOR OVERRIDES (modifications to sdm845-cheza.dtsi) */ + +/* + * L19 and L28 technically go to 3.3V, but most boards have old AOP firmware + * that limits them to 3.0, and trying to run at 3.3V with that old firmware + * prevents the system from booting. + */ +&src_pp3000_l19a { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; +}; + +&src_pp3300_l22a { + /delete-property/regulator-boot-on; + /delete-property/regulator-always-on; +}; + +&src_pp3300_l28a { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; +}; + +&src_vreg_bob { + regulator-min-microvolt = <3500000>; + regulator-max-microvolt = <3500000>; + vin-supply = <&pp3500_a_vbob>; +}; + +/* + * NON-REGULATOR OVERRIDES + * (modifications to sdm845-cheza.dtsi) - alphabetized by dtsi label + */ + +/* PINCTRL - board-specific pinctrl */ + +&tlmm { + gpio-line-names = "AP_SPI_FP_MISO", + "AP_SPI_FP_MOSI", + "AP_SPI_FP_CLK", + "AP_SPI_FP_CS_L", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "", + "FP_RST_L", + "FCAM_EN", + "", + "EDP_BRIJ_IRQ", + "EC_IN_RW_ODL", + "", + "RCAM_MCLK", + "FCAM_MCLK", + "", + "RCAM_EN", + "CCI0_SDA", + "CCI0_SCL", + "CCI1_SDA", + "CCI1_SCL", + "FCAM_RST_L", + "", + "PEN_RST_L", + "PEN_IRQ_L", + "", + "RCAM_VSYNC", + "ESIM_MISO", + "ESIM_MOSI", + "ESIM_CLK", + "ESIM_CS_L", + "AP_PEN_1V8_SDA", + "AP_PEN_1V8_SCL", + "AP_TS_I2C_SDA", + "AP_TS_I2C_SCL", + "RCAM_RST_L", + "", + "AP_EDP_BKLTEN", + "AP_BRD_ID1", + "BOOT_CONFIG_4", + "AMP_IRQ_L", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "EN_PP3300_DX_EDP", + "SD_CD_ODL", + "BT_UART_RTS", + "BT_UART_CTS", + "BT_UART_RXD", + "BT_UART_TXD", + "AMP_I2C_SDA", + "AMP_I2C_SCL", + "AP_BRD_ID3", + "", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "FORCED_USB_BOOT", + "AMP_BCLK", + "AMP_LRCLK", + "AMP_DOUT", + "AMP_DIN", + "AP_BRD_ID2", + "PEN_PDCT_L", + "HP_MCLK", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "", + "", + "", + "", + "BT_SLIMBUS_DATA", + "BT_SLIMBUS_CLK", + "AMP_RESET_L", + "", + "FCAM_VSYNC", + "", + "AP_SKU_ID1", + "EC_WOV_BCLK", + "EC_WOV_LRCLK", + "EC_WOV_DOUT", + "", + "", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "AP_SPI_CS0_L", + "AP_SPI_MOSI", + "AP_SPI_MISO", + "", + "", + "AP_SPI_CLK", + "", + "RFFE6_CLK", + "RFFE6_DATA", + "BOOT_CONFIG_1", + "BOOT_CONFIG_2", + "BOOT_CONFIG_0", + "EDP_BRIJ_EN", + "", + "USB_HS_TX_EN", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "AP_SKU_ID2", + "SDM_GRFC_8", + "SDM_GRFC_9", + "AP_RST_REQ", + "HP_IRQ", + "TS_RESET_L", + "PEN_EJECT_ODL", + "HUB_RST_L", + "FP_TO_AP_IRQ", + "AP_EC_INT_L", + "", + "", + "TS_INT_L", + "AP_SUSPEND_L", + "SDM_GRFC_3", + "", + "H1_AP_INT_ODL", + "QLINK_REQ", + "QLINK_EN", + "SDM_GRFC_2", + "BOOT_CONFIG_3", + "WMSS_RESET_L", + "SDM_GRFC_0", + "SDM_GRFC_1", + "RFFE3_DATA", + "RFFE3_CLK", + "RFFE4_DATA", + "RFFE4_CLK", + "RFFE5_DATA", + "RFFE5_CLK", + "GNSS_EN", + "WCI2_LTE_COEX_RXD", + "WCI2_LTE_COEX_TXD", + "AP_RAM_ID1", + "AP_RAM_ID2", + "RFFE1_DATA", + "RFFE1_CLK"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza-r2.dts b/arch/arm64/boot/dts/qcom/sdm845-cheza-r2.dts new file mode 100644 index 000000000000..2b7230594ecb --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-cheza-r2.dts @@ -0,0 +1,238 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Cheza board device tree source + * + * Copyright 2018 Google LLC. + */ + +/dts-v1/; + +#include "sdm845-cheza.dtsi" + +/ { + model = "Google Cheza (rev2)"; + compatible = "google,cheza-rev2", "qcom,sdm845"; + + /* + * FIXED REGULATORS (not in sdm845-cheza.dtsi) - parents above children + */ + + /* + * NOTE: Technically pp3500_a is not the exact same signal as + * pp3500_a_vbob (there's a load switch between them and the EC can + * control pp3500_a via "en_pp3300_a"), but from the AP's point of + * view they are the same. + */ + pp3500_a: + pp3500_a_vbob: pp3500-a-vbob-regulator { + compatible = "regulator-fixed"; + regulator-name = "vreg_bob"; + + /* + * Comes on automatically when pp5000_ldo comes on, which + * comes on automatically when ppvar_sys comes on + */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3500000>; + regulator-max-microvolt = <3500000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_dx_edp: pp3300-dx-edp-regulator { + /* Yes, it's really 3.5 despite the name of the signal */ + regulator-min-microvolt = <3500000>; + regulator-max-microvolt = <3500000>; + + vin-supply = <&pp3500_a>; + }; +}; + +/* FIXED REGULATOR OVERRIDES (modifications to sdm845-cheza.dtsi) */ + +/* + * L19 and L28 technically go to 3.3V, but most boards have old AOP firmware + * that limits them to 3.0, and trying to run at 3.3V with that old firmware + * prevents the system from booting. + */ +&src_pp3000_l19a { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; +}; + +&src_pp3300_l22a { + /delete-property/regulator-boot-on; + /delete-property/regulator-always-on; +}; + +&src_pp3300_l28a { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; +}; + +&src_vreg_bob { + regulator-min-microvolt = <3500000>; + regulator-max-microvolt = <3500000>; + vin-supply = <&pp3500_a_vbob>; +}; + +/* + * NON-REGULATOR OVERRIDES + * (modifications to sdm845-cheza.dtsi) - alphabetized by dtsi label + */ + +/* PINCTRL - board-specific pinctrl */ + +&tlmm { + gpio-line-names = "AP_SPI_FP_MISO", + "AP_SPI_FP_MOSI", + "AP_SPI_FP_CLK", + "AP_SPI_FP_CS_L", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "BRIJ_SUSPEND", + "FP_RST_L", + "FCAM_EN", + "", + "EDP_BRIJ_IRQ", + "EC_IN_RW_ODL", + "", + "RCAM_MCLK", + "FCAM_MCLK", + "", + "RCAM_EN", + "CCI0_SDA", + "CCI0_SCL", + "CCI1_SDA", + "CCI1_SCL", + "FCAM_RST_L", + "FPMCU_BOOT0", + "PEN_RST_L", + "PEN_IRQ_L", + "FPMCU_SEL_OD", + "RCAM_VSYNC", + "ESIM_MISO", + "ESIM_MOSI", + "ESIM_CLK", + "ESIM_CS_L", + "AP_PEN_1V8_SDA", + "AP_PEN_1V8_SCL", + "AP_TS_I2C_SDA", + "AP_TS_I2C_SCL", + "RCAM_RST_L", + "", + "AP_EDP_BKLTEN", + "AP_BRD_ID1", + "BOOT_CONFIG_4", + "AMP_IRQ_L", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "EN_PP3300_DX_EDP", + "SD_CD_ODL", + "BT_UART_RTS", + "BT_UART_CTS", + "BT_UART_RXD", + "BT_UART_TXD", + "AMP_I2C_SDA", + "AMP_I2C_SCL", + "AP_BRD_ID3", + "", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "FORCED_USB_BOOT", + "AMP_BCLK", + "AMP_LRCLK", + "AMP_DOUT", + "AMP_DIN", + "AP_BRD_ID2", + "PEN_PDCT_L", + "HP_MCLK", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "", + "", + "", + "", + "BT_SLIMBUS_DATA", + "BT_SLIMBUS_CLK", + "AMP_RESET_L", + "", + "FCAM_VSYNC", + "", + "AP_SKU_ID1", + "EC_WOV_BCLK", + "EC_WOV_LRCLK", + "EC_WOV_DOUT", + "", + "", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "AP_SPI_CS0_L", + "AP_SPI_MOSI", + "AP_SPI_MISO", + "", + "", + "AP_SPI_CLK", + "", + "RFFE6_CLK", + "RFFE6_DATA", + "BOOT_CONFIG_1", + "BOOT_CONFIG_2", + "BOOT_CONFIG_0", + "EDP_BRIJ_EN", + "", + "USB_HS_TX_EN", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "AP_SKU_ID2", + "SDM_GRFC_8", + "SDM_GRFC_9", + "AP_RST_REQ", + "HP_IRQ", + "TS_RESET_L", + "PEN_EJECT_ODL", + "HUB_RST_L", + "FP_TO_AP_IRQ", + "AP_EC_INT_L", + "", + "", + "TS_INT_L", + "AP_SUSPEND_L", + "SDM_GRFC_3", + "", + "H1_AP_INT_ODL", + "QLINK_REQ", + "QLINK_EN", + "SDM_GRFC_2", + "BOOT_CONFIG_3", + "WMSS_RESET_L", + "SDM_GRFC_0", + "SDM_GRFC_1", + "RFFE3_DATA", + "RFFE3_CLK", + "RFFE4_DATA", + "RFFE4_CLK", + "RFFE5_DATA", + "RFFE5_CLK", + "GNSS_EN", + "WCI2_LTE_COEX_RXD", + "WCI2_LTE_COEX_TXD", + "AP_RAM_ID1", + "AP_RAM_ID2", + "RFFE1_DATA", + "RFFE1_CLK"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza-r3.dts b/arch/arm64/boot/dts/qcom/sdm845-cheza-r3.dts new file mode 100644 index 000000000000..1ba67be08f81 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-cheza-r3.dts @@ -0,0 +1,174 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Cheza board device tree source + * + * Copyright 2018 Google LLC. + */ + +/dts-v1/; + +#include "sdm845-cheza.dtsi" + +/ { + model = "Google Cheza (rev3+)"; + compatible = "google,cheza", "qcom,sdm845"; +}; + +/* PINCTRL - board-specific pinctrl */ + +&tlmm { + gpio-line-names = "AP_SPI_FP_MISO", + "AP_SPI_FP_MOSI", + "AP_SPI_FP_CLK", + "AP_SPI_FP_CS_L", + "UART_AP_TX_DBG_RX", + "UART_DBG_TX_AP_RX", + "BRIJ_SUSPEND", + "FP_RST_L", + "FCAM_EN", + "", + "EDP_BRIJ_IRQ", + "EC_IN_RW_ODL", + "", + "RCAM_MCLK", + "FCAM_MCLK", + "", + "RCAM_EN", + "CCI0_SDA", + "CCI0_SCL", + "CCI1_SDA", + "CCI1_SCL", + "FCAM_RST_L", + "FPMCU_BOOT0", + "PEN_RST_L", + "PEN_IRQ_L", + "FPMCU_SEL_OD", + "RCAM_VSYNC", + "ESIM_MISO", + "ESIM_MOSI", + "ESIM_CLK", + "ESIM_CS_L", + "AP_PEN_1V8_SDA", + "AP_PEN_1V8_SCL", + "AP_TS_I2C_SDA", + "AP_TS_I2C_SCL", + "RCAM_RST_L", + "", + "AP_EDP_BKLTEN", + "AP_BRD_ID0", + "BOOT_CONFIG_4", + "AMP_IRQ_L", + "EDP_BRIJ_I2C_SDA", + "EDP_BRIJ_I2C_SCL", + "EN_PP3300_DX_EDP", + "SD_CD_ODL", + "BT_UART_RTS", + "BT_UART_CTS", + "BT_UART_RXD", + "BT_UART_TXD", + "AMP_I2C_SDA", + "AMP_I2C_SCL", + "AP_BRD_ID2", + "", + "AP_EC_SPI_CLK", + "AP_EC_SPI_CS_L", + "AP_EC_SPI_MISO", + "AP_EC_SPI_MOSI", + "FORCED_USB_BOOT", + "AMP_BCLK", + "AMP_LRCLK", + "AMP_DOUT", + "AMP_DIN", + "AP_BRD_ID1", + "PEN_PDCT_L", + "HP_MCLK", + "HP_BCLK", + "HP_LRCLK", + "HP_DOUT", + "HP_DIN", + "", + "", + "", + "", + "BT_SLIMBUS_DATA", + "BT_SLIMBUS_CLK", + "AMP_RESET_L", + "", + "FCAM_VSYNC", + "", + "AP_SKU_ID0", + "EC_WOV_BCLK", + "EC_WOV_LRCLK", + "EC_WOV_DOUT", + "", + "", + "AP_H1_SPI_MISO", + "AP_H1_SPI_MOSI", + "AP_H1_SPI_CLK", + "AP_H1_SPI_CS_L", + "", + "AP_SPI_CS0_L", + "AP_SPI_MOSI", + "AP_SPI_MISO", + "", + "", + "AP_SPI_CLK", + "", + "RFFE6_CLK", + "RFFE6_DATA", + "BOOT_CONFIG_1", + "BOOT_CONFIG_2", + "BOOT_CONFIG_0", + "EDP_BRIJ_EN", + "", + "USB_HS_TX_EN", + "UIM2_DATA", + "UIM2_CLK", + "UIM2_RST", + "UIM2_PRESENT", + "UIM1_DATA", + "UIM1_CLK", + "UIM1_RST", + "", + "AP_SKU_ID1", + "SDM_GRFC_8", + "SDM_GRFC_9", + "AP_RST_REQ", + "HP_IRQ", + "TS_RESET_L", + "PEN_EJECT_ODL", + "HUB_RST_L", + "FP_TO_AP_IRQ", + "AP_EC_INT_L", + "", + "", + "TS_INT_L", + "AP_SUSPEND_L", + "SDM_GRFC_3", + /* + * AP_FLASH_WP_L is crossystem ABI. Rev3 schematics + * call it BIOS_FLASH_WP_R_L. + */ + "AP_FLASH_WP_L", + "H1_AP_INT_ODL", + "QLINK_REQ", + "QLINK_EN", + "SDM_GRFC_2", + "BOOT_CONFIG_3", + "WMSS_RESET_L", + "SDM_GRFC_0", + "SDM_GRFC_1", + "RFFE3_DATA", + "RFFE3_CLK", + "RFFE4_DATA", + "RFFE4_CLK", + "RFFE5_DATA", + "RFFE5_CLK", + "GNSS_EN", + "WCI2_LTE_COEX_RXD", + "WCI2_LTE_COEX_TXD", + "AP_RAM_ID0", + "AP_RAM_ID1", + "RFFE1_DATA", + "RFFE1_CLK"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi new file mode 100644 index 000000000000..1ebbd568dfd7 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi @@ -0,0 +1,1326 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Google Cheza device tree source (common between revisions) + * + * Copyright 2018 Google LLC. + */ + +#include +#include +#include +#include "sdm845.dtsi" + +/* PMICs depend on spmi_bus label and so must come after SoC */ +#include "pm8005.dtsi" +#include "pm8998.dtsi" + +/ { + aliases { + bluetooth0 = &bluetooth; + hsuart0 = &uart6; + serial0 = &uart9; + wifi0 = &wifi; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&cros_ec_pwm 0>; + enable-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; + power-supply = <&ppvar_sys>; + pinctrl-names = "default"; + pinctrl-0 = <&ap_edp_bklten>; + }; + + /* FIXED REGULATORS - parents above children */ + + /* This is the top level supply and variable voltage */ + ppvar_sys: ppvar-sys-regulator { + compatible = "regulator-fixed"; + regulator-name = "ppvar_sys"; + regulator-always-on; + regulator-boot-on; + }; + + /* This divides ppvar_sys by 2, so voltage is variable */ + src_vph_pwr: src-vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "src_vph_pwr"; + + /* EC turns on with switchcap_on_l; always on for AP */ + regulator-always-on; + regulator-boot-on; + + vin-supply = <&ppvar_sys>; + }; + + pp5000_a: pp5000-a-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp5000_a"; + + /* EC turns on with en_pp5000_a; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&ppvar_sys>; + }; + + src_vreg_bob: src-vreg-bob-regulator { + compatible = "regulator-fixed"; + regulator-name = "src_vreg_bob"; + + /* EC turns on with vbob_en; always on for AP */ + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + + vin-supply = <&ppvar_sys>; + }; + + pp3300_dx_edp: pp3300-dx-edp-regulator { + compatible = "regulator-fixed"; + regulator-name = "pp3300_dx_edp"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 43 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_pp3300_dx_edp>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + src_pp1800_s4a: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "src_pp1800_s4a"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&src_vph_pwr>; + }; + + /* BOARD-SPECIFIC TOP LEVEL NODES */ + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pen_eject_odl>; + + pen-insert { + label = "Pen Insert"; + /* Insert = low, eject = high */ + gpios = <&tlmm 119 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + wakeup-source; + }; + }; + + panel: panel { + compatible ="innolux,p120zdg-bf1"; + power-supply = <&pp3300_dx_edp>; + backlight = <&backlight>; + no-hpd; + + ports { + panel_in: port { + panel_in_edp: endpoint { + remote-endpoint = <&sn65dsi86_out>; + }; + }; + }; + }; +}; + +/* + * Reserved memory changes + * + * Putting this all together (out of order with the rest of the file) to keep + * all modifications to the memory map (from sdm845.dtsi) in one place. + */ + +/* + * Our mpss_region is 8MB bigger than the default one and that conflicts + * with venus_mem and cdsp_mem. + * + * For venus_mem we'll delete and re-create at a different address. + * + * cdsp_mem isn't used on cheza right now so we won't bother re-creating it; but + * that also means we need to delete cdsp_pas. + */ +/delete-node/ &venus_mem; +/delete-node/ &cdsp_mem; +/delete-node/ &cdsp_pas; + +/* Increase the size from 120 MB to 128 MB */ +&mpss_region { + reg = <0 0x8e000000 0 0x8000000>; +}; + +/* Increase the size from 2MB to 8MB */ +&rmtfs_mem { + reg = <0 0x88f00000 0 0x800000>; +}; + +/ { + reserved-memory { + venus_mem: memory@96000000 { + reg = <0 0x96000000 0 0x500000>; + no-map; + }; + }; +}; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + + /* + * In theory chip supports up to 104 MHz and controller up + * to 80 MHz, but above 25 MHz wasn't reliable so we'll use + * that for now. b:117440651 + */ + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&src_vph_pwr>; + vdd-s2-supply = <&src_vph_pwr>; + vdd-s3-supply = <&src_vph_pwr>; + vdd-s4-supply = <&src_vph_pwr>; + vdd-s5-supply = <&src_vph_pwr>; + vdd-s6-supply = <&src_vph_pwr>; + vdd-s7-supply = <&src_vph_pwr>; + vdd-s8-supply = <&src_vph_pwr>; + vdd-s9-supply = <&src_vph_pwr>; + vdd-s10-supply = <&src_vph_pwr>; + vdd-s11-supply = <&src_vph_pwr>; + vdd-s12-supply = <&src_vph_pwr>; + vdd-s13-supply = <&src_vph_pwr>; + vdd-l1-l27-supply = <&src_pp1025_s7a>; + vdd-l2-l8-l17-supply = <&src_pp1350_s3a>; + vdd-l3-l11-supply = <&src_pp1025_s7a>; + vdd-l4-l5-supply = <&src_pp1025_s7a>; + vdd-l6-supply = <&src_vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&src_pp2040_s5a>; + vdd-l9-supply = <&src_pp2040_s5a>; + vdd-l10-l23-l25-supply = <&src_vreg_bob>; + vdd-l13-l19-l21-supply = <&src_vreg_bob>; + vdd-l16-l28-supply = <&src_vreg_bob>; + vdd-l18-l22-supply = <&src_vreg_bob>; + vdd-l20-l24-supply = <&src_vreg_bob>; + vdd-l26-supply = <&src_pp1350_s3a>; + vin-lvs-1-2-supply = <&src_pp1800_s4a>; + + src_pp1125_s2a: smps2 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + src_pp1350_s3a: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + src_pp2040_s5a: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + src_pp1025_s7a: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdd_qusb_hs0: + vdda_hp_pcie_core: + vdda_mipi_csi0_0p9: + vdda_mipi_csi1_0p9: + vdda_mipi_csi2_0p9: + vdda_mipi_dsi0_pll: + vdda_mipi_dsi1_pll: + vdda_qlink_lv: + vdda_qlink_lv_ck: + vdda_qrefs_0p875: + vdda_pcie_core: + vdda_pll_cc_ebi01: + vdda_pll_cc_ebi23: + vdda_sp_sensor: + vdda_ufs1_core: + vdda_ufs2_core: + vdda_usb1_ss_core: + vdda_usb2_ss_core: + src_pp875_l1a: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = ; + }; + + vddpx_10: + src_pp1200_l2a: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + + /* TODO: why??? */ + regulator-always-on; + }; + + pp1000_l3a_sdr845: ldo3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-initial-mode = ; + }; + + vdd_wcss_cx: + vdd_wcss_mx: + vdda_wcss_pll: + src_pp800_l5a: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = ; + }; + + vddpx_13: + src_pp1800_l6a: ldo6 { + regulator-min-microvolt = <1856000>; + regulator-max-microvolt = <1856000>; + regulator-initial-mode = ; + }; + + pp1800_l7a_wcn3990: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + src_pp1200_l8a: ldo8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1248000>; + regulator-initial-mode = ; + }; + + pp1800_dx_pen: + src_pp1800_l9a: ldo9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + src_pp1800_l10a: ldo10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + pp1000_l11a_sdr845: ldo11 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1048000>; + regulator-initial-mode = ; + }; + + vdd_qfprom: + vdd_qfprom_sp: + vdda_apc1_cs_1p8: + vdda_gfx_cs_1p8: + vdda_qrefs_1p8: + vdda_qusb_hs0_1p8: + vddpx_11: + src_pp1800_l12a: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + vddpx_2: + src_pp2950_l13a: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = ; + }; + + src_pp1800_l14a: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + src_pp1800_l15a: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + pp2700_l16a: ldo16 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2704000>; + regulator-initial-mode = ; + }; + + src_pp1300_l17a: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = ; + }; + + pp2700_l18a: ldo18 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = ; + }; + + /* + * NOTE: this rail should have been called + * src_pp3300_l19a in the schematic + */ + src_pp3000_l19a: ldo19 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + + regulator-initial-mode = ; + }; + + src_pp2950_l20a: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = ; + }; + + src_pp2950_l21a: ldo21 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = ; + }; + + pp3300_hub: + src_pp3300_l22a: ldo22 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = ; + /* + * HACK: Should add a usb hub node and driver + * to turn this on and off at suspend/resume time + */ + regulator-boot-on; + regulator-always-on; + }; + + pp3300_l23a_ch1_wcn3990: ldo23 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = ; + }; + + vdda_qusb_hs0_3p1: + src_pp3075_l24a: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = ; + }; + + pp3300_l25a_ch0_wcn3990: ldo25 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = ; + }; + + pp1200_hub: + vdda_hp_pcie_1p2: + vdda_hv_ebi0: + vdda_hv_ebi1: + vdda_hv_ebi2: + vdda_hv_ebi3: + vdda_mipi_csi_1p25: + vdda_mipi_dsi0_1p2: + vdda_mipi_dsi1_1p2: + vdda_pcie_1p2: + vdda_ufs1_1p2: + vdda_ufs2_1p2: + vdda_usb1_ss_1p2: + vdda_usb2_ss_1p2: + src_pp1200_l26a: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + + pp3300_dx_pen: + src_pp3300_l28a: ldo28 { + regulator-min-microvolt = <3304000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = ; + }; + + src_pp1800_lvs1: lvs1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + src_pp1800_lvs2: lvs2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&src_vph_pwr>; + vdd-s2-supply = <&src_vph_pwr>; + vdd-s3-supply = <&src_vph_pwr>; + vdd-s4-supply = <&src_vph_pwr>; + + src_pp600_s3c: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&sn65dsi86_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +edp_brij_i2c: &i2c3 { + status = "okay"; + clock-frequency = <400000>; + + sn65dsi86_bridge: bridge@2d { + compatible = "ti,sn65dsi86"; + reg = <0x2d>; + pinctrl-names = "default"; + pinctrl-0 = <&edp_brij_en &edp_brij_irq>; + + interrupt-parent = <&tlmm>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>; + + vpll-supply = <&src_pp1800_s4a>; + vccio-supply = <&src_pp1800_s4a>; + vcca-supply = <&src_pp1200_l2a>; + vcc-supply = <&src_pp1200_l2a>; + + clocks = <&rpmhcc RPMH_LN_BB_CLK2>; + clock-names = "refclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + sn65dsi86_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + sn65dsi86_out: endpoint { + remote-endpoint = <&panel_in_edp>; + }; + }; + }; + }; +}; + +ap_pen_1v8: &i2c11 { + status = "okay"; + clock-frequency = <400000>; + + digitizer@9 { + compatible = "wacom,w9013", "hid-over-i2c"; + reg = <0x9>; + pinctrl-names = "default"; + pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>; + + vdd-supply = <&pp3300_dx_pen>; + vddl-supply = <&pp1800_dx_pen>; + post-power-on-delay-ms = <100>; + + interrupt-parent = <&tlmm>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; + + hid-descr-addr = <0x1>; + }; +}; + +amp_i2c: &i2c12 { + status = "okay"; + clock-frequency = <400000>; +}; + +ap_ts_i2c: &i2c14 { + status = "okay"; + clock-frequency = <400000>; + + touchscreen@10 { + compatible = "elan,ekth3500"; + reg = <0x10>; + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_l &ts_reset_l>; + + interrupt-parent = <&tlmm>; + interrupts = <125 IRQ_TYPE_LEVEL_LOW>; + + vcc33-supply = <&src_pp3300_l28a>; + + reset-gpios = <&tlmm 118 GPIO_ACTIVE_LOW>; + }; +}; + +&lpasscc { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_cd_odl>; + + vmmc-supply = <&src_pp2950_l21a>; + vqmmc-supply = <&vddpx_2>; + + cd-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; +}; + +&spi0 { + status = "okay"; +}; + +&spi10 { + status = "okay"; + + cros_ec: ec@0 { + compatible = "google,cros-ec-spi"; + reg = <0>; + interrupt-parent = <&tlmm>; + interrupts = <122 IRQ_TYPE_LEVEL_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&ec_ap_int_l>; + spi-max-frequency = <3000000>; + + cros_ec_pwm: ec-pwm { + compatible = "google,cros-ec-pwm"; + #pwm-cells = <1>; + }; + + i2c_tunnel: i2c-tunnel { + compatible = "google,cros-ec-i2c-tunnel"; + google,remote-bus = <0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + pdupdate { + compatible = "google,cros-ec-pd-update"; + }; + }; +}; + +#include +#include + +&uart6 { + status = "okay"; + + bluetooth: wcn3990-bt { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&src_pp1800_s4a>; + vddxo-supply = <&pp1800_l7a_wcn3990>; + vddrf-supply = <&src_pp1300_l17a>; + vddch0-supply = <&pp3300_l25a_ch0_wcn3990>; + max-speed = <3200000>; + }; +}; + +&uart9 { + status = "okay"; +}; + +&ufs_mem_hc { + status = "okay"; + pinctrl-names = "init", "default"; + pinctrl-0 = <&ufs_dev_reset_assert>; + pinctrl-1 = <&ufs_dev_reset_deassert>; + + vcc-supply = <&src_pp2950_l20a>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* We'll use this as USB 2.0 only */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * The hardware design intends this port to be hooked up in peripheral + * mode, so we'll hardcode it here. Some details: + * - SDM845 expects only a single Type C connector so it has only one + * native Type C port but cheza has two Type C connectors. + * - The only source of DP is the single native Type C port. + * - On cheza we want to be able to hook DP up to _either_ of the + * two Type C connectors and want to be able to achieve 4 lanes of DP. + * - When you configure a Type C port for 4 lanes of DP you lose USB3. + * - In order to make everything work, the native Type C port is always + * configured as 4-lanes DP so it's always available. + * - The extra USB3 port on SDM845 goes to a USB 3 hub which is then + * sent to the two Type C connectors. + * - The extra USB2 lines from the native Type C port are always + * setup as "peripheral" so that we can mux them over to one connector + * or the other if someone needs the connector configured as a gadget + * (but they only get USB2 speeds). + * + * All the hardware muxes would allow us to hook things up in different + * ways to some potential benefit for static configurations (you could + * achieve extra USB2 bandwidth by using two different ports for the + * two conenctors or possibly even get USB3 peripheral mode), but in + * each case you end up forcing to disconnect/reconnect an in-use + * USB session in some cases depending on what you hotplug into the + * other connector. Thus hardcoding this as peripheral makes sense. + */ + dr_mode = "peripheral"; + + /* + * We always need the high speed pins as 4-lanes DP in case someone + * hotplugs a DP peripheral. Thus limit this port to a max of high + * speed. + */ + maximum-speed = "high-speed"; + + /* + * We don't need the usb3-phy since we run in highspeed mode always, so + * re-define these properties removing the superspeed USB PHY reference. + */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = ; + qcom,preemphasis-level = ; + qcom,preemphasis-width = ; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + /* We have this hooked up to a hub and we always use in host mode */ + dr_mode = "host"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb2_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = ; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vdda_usb2_ss_1p2>; + vdda-pll-supply = <&vdda_usb2_ss_core>; +}; + +&wifi { + status = "okay"; + + vdd-0.8-cx-mx-supply = <&src_pp800_l5a >; + vdd-1.8-xo-supply = <&pp1800_l7a_wcn3990>; + vdd-1.3-rfa-supply = <&src_pp1300_l17a>; + vdd-3.3-ch0-supply = <&pp3300_l25a_ch0_wcn3990>; +}; + +/* PINCTRL - additions to nodes defined in sdm845.dtsi */ + +&qspi_cs0 { + pinconf { + pins = "gpio90"; + bias-disable; + }; +}; + +&qspi_clk { + pinconf { + pins = "gpio95"; + bias-disable; + }; +}; + +&qspi_data01 { + pinconf { + pins = "gpio91", "gpio92"; + + /* High-Z when no transfers; nice to park the lines */ + bias-pull-up; + }; +}; + +&qup_i2c3_default { + pinconf { + pins = "gpio41", "gpio42"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_i2c11_default { + pinconf { + pins = "gpio31", "gpio32"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_i2c12_default { + pinconf { + pins = "gpio49", "gpio50"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_i2c14_default { + pinconf { + pins = "gpio33", "gpio34"; + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; + }; +}; + +&qup_spi0_default { + pinconf { + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_spi5_default { + pinconf { + pins = "gpio85", "gpio86", "gpio87", "gpio88"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_spi10_default { + pinconf { + pins = "gpio53", "gpio54", "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart6_default { + /* Change pinmux to all 4 pins since CTS and RTS are connected */ + pinmux { + pins = "gpio45", "gpio46", + "gpio47", "gpio48"; + }; + + pinconf-cts { + /* + * Configure a pull-down on 45 (CTS) to match the pull of + * the Bluetooth module. + */ + pins = "gpio45"; + bias-pull-down; + }; + + pinconf-rts-tx { + /* We'll drive 46 (RTS) and 47 (TX), so no pull */ + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + /* + * Configure a pull-up on 48 (RX). This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + pins = "gpio48"; + bias-pull-up; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +/* PINCTRL - board-specific pinctrl */ +&pm8005_gpio { + gpio-line-names = "", + "", + "SLB", + ""; +}; + +&pm8998_adc { + adc-chan@ADC5_AMUX_THM1_100K_PU { + reg = ; + label = "sdm_temp"; + }; + + adc-chan@ADC5_AMUX_THM2_100K_PU { + reg = ; + label = "quiet_temp"; + }; + + adc-chan@ADC5_AMUX_THM3_100K_PU { + reg = ; + label = "lte_temp_1"; + }; + + adc-chan@ADC5_AMUX_THM4_100K_PU { + reg = ; + label = "lte_temp_2"; + }; + + adc-chan@ADC5_AMUX_THM5_100K_PU { + reg = ; + label = "charger_temp"; + }; +}; + +&pm8998_gpio { + gpio-line-names = "", + "", + "SW_CTRL", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "", + "CFG_OPT1", + "WCSS_PWR_REQ", + "", + "CFG_OPT2", + "SLB"; +}; + +&tlmm { + /* + * pinctrl settings for pins that have no real owners. + */ + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&bios_flash_wp_r_l>, + <&ap_suspend_l_deassert>; + + pinctrl-1 = <&bios_flash_wp_r_l>, + <&ap_suspend_l_assert>; + + /* + * Hogs prevent usermode from changing the value. A GPIO can be both + * here and in the pinctrl section. + */ + ap-suspend-l-hog { + gpio-hog; + gpios = <126 GPIO_ACTIVE_LOW>; + output-low; + }; + + ap_edp_bklten: ap-edp-bklten { + pinmux { + pins = "gpio37"; + function = "gpio"; + }; + + pinconf { + pins = "gpio37"; + drive-strength = <2>; + bias-disable; + }; + }; + + bios_flash_wp_r_l: bios-flash-wp-r-l { + pinmux { + pins = "gpio128"; + function = "gpio"; + input-enable; + }; + + pinconf { + pins = "gpio128"; + bias-disable; + }; + }; + + ec_ap_int_l: ec-ap-int-l { + pinmux { + pins = "gpio122"; + function = "gpio"; + input-enable; + }; + + pinconf { + pins = "gpio122"; + bias-pull-up; + }; + }; + + edp_brij_en: edp-brij-en { + pinmux { + pins = "gpio102"; + function = "gpio"; + }; + + pinconf { + pins = "gpio102"; + drive-strength = <2>; + bias-disable; + }; + }; + + edp_brij_irq: edp-brij-irq { + pinmux { + pins = "gpio10"; + function = "gpio"; + }; + + pinconf { + pins = "gpio10"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + en_pp3300_dx_edp: en-pp3300-dx-edp { + pinmux { + pins = "gpio43"; + function = "gpio"; + }; + + pinconf { + pins = "gpio43"; + drive-strength = <2>; + bias-disable; + }; + }; + + h1_ap_int_odl: h1-ap-int-odl { + pinmux { + pins = "gpio129"; + function = "gpio"; + input-enable; + }; + + pinconf { + pins = "gpio129"; + bias-pull-up; + }; + }; + + pen_eject_odl: pen-eject-odl { + pinmux { + pins = "gpio119"; + function = "gpio"; + bias-pull-up; + }; + }; + + pen_irq_l: pen-irq-l { + pinmux { + pins = "gpio24"; + function = "gpio"; + }; + + pinconf { + pins = "gpio24"; + + /* Has external pullup */ + bias-disable; + }; + }; + + pen_pdct_l: pen-pdct-l { + pinmux { + pins = "gpio63"; + function = "gpio"; + }; + + pinconf { + pins = "gpio63"; + + /* Has external pullup */ + bias-disable; + }; + }; + + pen_rst_l: pen-rst-l { + pinmux { + pins = "gpio23"; + function = "gpio"; + }; + + pinconf { + pins = "gpio23"; + bias-disable; + drive-strength = <2>; + + /* + * The pen driver doesn't currently support + * driving this reset line. By specifying + * output-high here we're relying on the fact + * that this pin has a default pulldown at boot + * (which makes sure the pen was in reset if it + * was powered) and then we set it high here to + * take it out of reset. Better would be if the + * pen driver could control this and we could + * remove "output-high" here. + */ + output-high; + }; + }; + + sdc2_clk: sdc2-clk { + pinconf { + pins = "sdc2_clk"; + bias-disable; + + /* + * It seems that mmc_test reports errors if drive + * strength is not 16. + */ + drive-strength = <16>; + }; + }; + + sdc2_cmd: sdc2-cmd { + pinconf { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + sdc2_data: sdc2-data { + pinconf { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <16>; + }; + }; + + sd_cd_odl: sd-cd-odl { + pinmux { + pins = "gpio44"; + function = "gpio"; + }; + + pinconf { + pins = "gpio44"; + bias-pull-up; + }; + }; + + ts_int_l: ts-int-l { + pinmux { + pins = "gpio125"; + function = "gpio"; + }; + + pinconf { + pins = "gpio125"; + bias-pull-up; + }; + }; + + ts_reset_l: ts-reset-l { + pinmux { + pins = "gpio118"; + function = "gpio"; + }; + + pinconf { + pins = "gpio118"; + bias-disable; + drive-strength = <2>; + }; + }; + + ufs_dev_reset_assert: ufs_dev_reset_assert { + config { + pins = "ufs_reset"; + bias-pull-down; /* default: pull down */ + /* + * UFS_RESET driver strengths are having + * different values/steps compared to typical + * GPIO drive strengths. + * + * Following table clarifies: + * + * HDRV value | UFS_RESET | Typical GPIO + * (dec) | (mA) | (mA) + * 0 | 0.8 | 2 + * 1 | 1.55 | 4 + * 2 | 2.35 | 6 + * 3 | 3.1 | 8 + * 4 | 3.9 | 10 + * 5 | 4.65 | 12 + * 6 | 5.4 | 14 + * 7 | 6.15 | 16 + * + * POR value for UFS_RESET HDRV is 3 which means + * 3.1mA and we want to use that. Hence just + * specify 8mA to "drive-strength" binding and + * that should result into writing 3 to HDRV + * field. + */ + drive-strength = <8>; /* default: 3.1 mA */ + output-low; /* active low reset */ + }; + }; + + ufs_dev_reset_deassert: ufs_dev_reset_deassert { + config { + pins = "ufs_reset"; + bias-pull-down; /* default: pull down */ + /* + * default: 3.1 mA + * check comments under ufs_dev_reset_assert + */ + drive-strength = <8>; + output-high; /* active low reset */ + }; + }; + + ap_suspend_l_assert: ap_suspend_l_assert { + config { + pins = "gpio126"; + function = "gpio"; + bias-no-pull; + drive-strength = <2>; + output-low; + }; + }; + + ap_suspend_l_deassert: ap_suspend_l_deassert { + config { + pins = "gpio126"; + function = "gpio"; + bias-no-pull; + drive-strength = <2>; + output-high; + }; + }; +}; -- cgit v1.2.3 From 8291e15108cde33c3e086a34af5381c95cc7aa87 Mon Sep 17 00:00:00 2001 From: Niklas Cassel Date: Thu, 27 Jun 2019 16:02:15 +0200 Subject: arm64: dts: qcom: qcs404: Add missing space for cooling-cells property There should be a space both before and after the equal sign. Add a missing space for the cooling cells property. Fixes: f48cee3239a1 ("arm64: dts: qcom: qcs404: Add thermal zones for each sensor") Signed-off-by: Niklas Cassel Acked-by: Amit Kucheria Signed-off-by: Andy Gross --- arch/arm64/boot/dts/qcom/qcs404.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/arm64/boot') diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi index 01a51f381850..3d0789775009 100644 --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi @@ -35,7 +35,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; - #cooling-cells= <2>; + #cooling-cells = <2>; }; CPU1: cpu@101 { @@ -45,7 +45,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; - #cooling-cells= <2>; + #cooling-cells = <2>; }; CPU2: cpu@102 { @@ -55,7 +55,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; - #cooling-cells= <2>; + #cooling-cells = <2>; }; CPU3: cpu@103 { @@ -65,7 +65,7 @@ enable-method = "psci"; cpu-idle-states = <&CPU_SLEEP_0>; next-level-cache = <&L2_0>; - #cooling-cells= <2>; + #cooling-cells = <2>; }; L2_0: l2-cache { -- cgit v1.2.3