From 0d963ebf57d4c6374b3a33050a18af23c1e2ede1 Mon Sep 17 00:00:00 2001 From: Jan Kiszka Date: Fri, 2 Jun 2017 07:27:59 +0200 Subject: serial: exar: Factor out platform hooks This prepares the addition of IOT2040 platform support by preparing the needed setup and rs485_config hooks. Signed-off-by: Jan Kiszka Reviewed-by: Andy Shevchenko Acked-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_exar.c | 32 +++++++++++++++++++++++++++----- 1 file changed, 27 insertions(+), 5 deletions(-) (limited to 'drivers/tty') diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c index 32e3cb58193f..575a252dc936 100644 --- a/drivers/tty/serial/8250/8250_exar.c +++ b/drivers/tty/serial/8250/8250_exar.c @@ -63,6 +63,11 @@ struct exar8250; +struct exar8250_platform { + int (*rs485_config)(struct uart_port *, struct serial_rs485 *); + int (*register_gpio)(struct pci_dev *, struct uart_8250_port *); +}; + /** * struct exar8250_board - board information * @num_ports: number of serial ports @@ -189,7 +194,7 @@ static void setup_gpio(u8 __iomem *p) } static void * -xr17v35x_register_gpio(struct pci_dev *pcidev) +__xr17v35x_register_gpio(struct pci_dev *pcidev) { struct platform_device *pdev; @@ -208,17 +213,36 @@ xr17v35x_register_gpio(struct pci_dev *pcidev) return pdev; } +static int xr17v35x_register_gpio(struct pci_dev *pcidev, + struct uart_8250_port *port) +{ + if (pcidev->vendor == PCI_VENDOR_ID_EXAR) + port->port.private_data = + __xr17v35x_register_gpio(pcidev); + + return 0; +} + +static const struct exar8250_platform exar8250_default_platform = { + .register_gpio = xr17v35x_register_gpio, +}; + static int pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev, struct uart_8250_port *port, int idx) { const struct exar8250_board *board = priv->board; + const struct exar8250_platform *platform; unsigned int offset = idx * 0x400; unsigned int baud = 7812500; u8 __iomem *p; int ret; + platform = &exar8250_default_platform; + port->port.uartclk = baud * 16; + port->port.rs485_config = platform->rs485_config; + /* * Setup the uart clock for the devices on expansion slot to * half the clock speed of the main chip (which is 125MHz) @@ -241,12 +265,10 @@ pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev, /* Setup Multipurpose Input/Output pins. */ setup_gpio(p); - if (pcidev->vendor == PCI_VENDOR_ID_EXAR) - port->port.private_data = - xr17v35x_register_gpio(pcidev); + ret = platform->register_gpio(pcidev, port); } - return 0; + return ret; } static void pci_xr17v35x_exit(struct pci_dev *pcidev) -- cgit v1.2.3