// SPDX-License-Identifier: GPL-2.0-only /* * Xilinx gpio driver for xps/axi_gpio IP. * * Copyright 2008 - 2013 Xilinx, Inc. */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include /* Register Offset Definitions */ #define XGPIO_DATA_OFFSET (0x0) /* Data register */ #define XGPIO_TRI_OFFSET (0x4) /* I/O direction register */ #define XGPIO_CHANNEL0_OFFSET 0x0 #define XGPIO_CHANNEL1_OFFSET 0x8 #define XGPIO_GIER_OFFSET 0x11c /* Global Interrupt Enable */ #define XGPIO_GIER_IE BIT(31) #define XGPIO_IPISR_OFFSET 0x120 /* IP Interrupt Status */ #define XGPIO_IPIER_OFFSET 0x128 /* IP Interrupt Enable */ /* Read/Write access to the GPIO registers */ #if defined(CONFIG_ARCH_ZYNQ) || defined(CONFIG_X86) # define xgpio_readreg(offset) readl(offset) # define xgpio_writereg(offset, val) writel(val, offset) #else # define xgpio_readreg(offset) __raw_readl(offset) # define xgpio_writereg(offset, val) __raw_writel(val, offset) #endif /** * struct xgpio_instance - Stores information about GPIO device * @gc: GPIO chip * @regs: register block * @hw_map: GPIO pin mapping on hardware side * @sw_map: GPIO pin mapping on software side * @state: GPIO write state shadow register * @last_irq_read: GPIO read state register from last interrupt * @dir: GPIO direction shadow register * @gpio_lock: Lock used for synchronization * @irq: IRQ used by GPIO device * @enable: GPIO IRQ enable/disable bitfield * @rising_edge: GPIO IRQ rising edge enable/disable bitfield * @falling_edge: GPIO IRQ falling edge enable/disable bitfield * @clk: clock resource for this driver */ struct xgpio_instance { struct gpio_chip gc; void __iomem *regs; DECLARE_BITMAP(hw_map, 64); DECLARE_BITMAP(sw_map, 64); DECLARE_BITMAP(state, 64); DECLARE_BITMAP(last_irq_read, 64); DECLARE_BITMAP(dir, 64); spinlock_t gpio_lock; /* For serializing operations */ int irq; DECLARE_BITMAP(enable, 64); DECLARE_BITMAP(rising_edge, 64); DECLARE_BITMAP(falling_edge, 64); struct clk *clk; }; static inline int xgpio_from_bit(struct xgpio_instance *chip, int bit) { return bitmap_bitremap(bit, chip->hw_map, chip->sw_map, 64); } static inline int xgpio_to_bit(struct xgpio_instance *chip, int gpio) { return bitmap_bitremap(gpio, chip->sw_map, chip->hw_map, 64); } static inline u32 xgpio_get_value32(const unsigned long *map, int bit) { const size_t index = BIT_WORD(bit); const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5); return (map[index] >> offset) & 0xFFFFFFFFul; } static inline void xgpio_set_value32(unsigned long *map, int bit, u32 v) { const size_t index = BIT_WORD(bit); const unsigned long offset = (bit % BITS_PER_LONG) & BIT(5); map[index] &= ~(0xFFFFFFFFul << offset); map[index] |= (unsigned long)v << offset; } static inline int xgpio_regoffset(struct xgpio_instance *chip, int ch) { switch (ch) { case 0: return XGPIO_CHANNEL0_OFFSET; case 1: return XGPIO_CHANNEL1_OFFSET; default: return -EINVAL; } } static void xgpio_read_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a) { void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32); xgpio_set_value32(a, bit, xgpio_readreg(addr)); } static void xgpio_write_ch(struct xgpio_instance *chip, int reg, int bit, unsigned long *a) { void __iomem *addr = chip->regs + reg + xgpio_regoffset(chip, bit / 32); xgpio_writereg(addr, xgpio_get_value32(a, bit)); } static void xgpio_read_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a) { int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1); for (bit = 0; bit <= lastbit ; bit += 32) xgpio_read_ch(chip, reg, bit, a); } static void xgpio_write_ch_all(struct xgpio_instance *chip, int reg, unsigned long *a) { int bit, lastbit = xgpio_to_bit(chip, chip->gc.ngpio - 1); for (bit = 0; bit <= lastbit ; bit += 32) xgpio_write_ch(chip, reg, bit, a); } /** * xgpio_get - Read the specified signal of the GPIO device. * @gc: Pointer to gpio_chip device structure. * @gpio: GPIO signal number. * * This function reads the specified signal of the GPIO device. * * Return: * 0 if direction of GPIO signals is set as input otherwise it * returns negative error value. */ static int xgpio_get(struct gpio_chip *gc, unsigned int gpio) { struct xgpio_instance *chip = gpiochip_get_data(gc); int bit = xgpio_to_bit(chip, gpio); DECLARE_BITMAP(state, 64); xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, state); return test_bit(bit, state); } /** * xgpio_set - Write the specified signal of the GPIO device. * @gc: Pointer to gpio_chip device structure. * @gpio: GPIO signal number. * @val: Value to be written to specified signal. * * This function writes the specified value in to the specified signal of the * GPIO device. */ static void xgpio_set(struct gpio_chip *gc, unsigned int gpio, int val) { unsigned long flags; struct xgpio_instance *chip = gpiochip_get_data(gc); int bit = xgpio_to_bit(chip, gpio); spin_lock_irqsave(&chip->gpio_lock, flags); /* Write to GPIO signal and set its direction to output */ __assign_bit(bit, chip->state, val); xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state); spin_unlock_irqrestore(&chip->gpio_lock, flags); } /** * xgpio_set_multiple - Write the specified signals of the GPIO device. * @gc: Pointer to gpio_chip device structure. * @mask: Mask of the GPIOS to modify. * @bits: Value to be wrote on each GPIO * * This function writes the specified values into the specified signals of the * GPIO devices. */ static void xgpio_set_multiple(struct gpio_chip *gc, unsigned long *mask, unsigned long *bits) { DECLARE_BITMAP(hw_mask, 64); DECLARE_BITMAP(hw_bits, 64); DECLARE_BITMAP(state, 64); unsigned long flags; struct xgpio_instance *chip = gpiochip_get_data(gc); bitmap_remap(hw_mask, mask, chip->sw_map, chip->hw_map, 64); bitmap_remap(hw_bits, bits, chip->sw_map, chip->hw_map, 64); spin_lock_irqsave(&chip->gpio_lock, flags); bitmap_replace(state, chip->state, hw_bits, hw_mask, 64); xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, state); bitmap_copy(chip->state, state, 64); spin_unlock_irqrestore(&chip->gpio_lock, flags); } /** * xgpio_dir_in - Set the direction of the specified GPIO signal as input. * @gc: Pointer to gpio_chip device structure. * @gpio: GPIO signal number. * * Return: * 0 - if direction of GPIO signals is set as input * otherwise it returns negative error value. */ static int xgpio_dir_in(struct gpio_chip *gc, unsigned int gpio) { unsigned long flags; struct xgpio_instance *chip = gpiochip_get_data(gc); int bit = xgpio_to_bit(chip, gpio); spin_lock_irqsave(&chip->gpio_lock, flags); /* Set the GPIO bit in shadow register and set direction as input */ __set_bit(bit, chip->dir); xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir); spin_unlock_irqrestore(&chip->gpio_lock, flags); return 0; } /** * xgpio_dir_out - Set the direction of the specified GPIO signal as output. * @gc: Pointer to gpio_chip device structure. * @gpio: GPIO signal number. * @val: Value to be written to specified signal. * * This function sets the direction of specified GPIO signal as output. * * Return: * If all GPIO signals of GPIO chip is configured as input then it returns * error otherwise it returns 0. */ static int xgpio_dir_out(struct gpio_chip *gc, unsigned int gpio, int val) { unsigned long flags; struct xgpio_instance *chip = gpiochip_get_data(gc); int bit = xgpio_to_bit(chip, gpio); spin_lock_irqsave(&chip->gpio_lock, flags); /* Write state of GPIO signal */ __assign_bit(bit, chip->state, val); xgpio_write_ch(chip, XGPIO_DATA_OFFSET, bit, chip->state); /* Clear the GPIO bit in shadow register and set direction as output */ __clear_bit(bit, chip->dir); xgpio_write_ch(chip, XGPIO_TRI_OFFSET, bit, chip->dir); spin_unlock_irqrestore(&chip->gpio_lock, flags); return 0; } /** * xgpio_save_regs - Set initial values of GPIO pins * @chip: Pointer to GPIO instance */ static void xgpio_save_regs(struct xgpio_instance *chip) { xgpio_write_ch_all(chip, XGPIO_DATA_OFFSET, chip->state); xgpio_write_ch_all(chip, XGPIO_TRI_OFFSET, chip->dir); } static int xgpio_request(struct gpio_chip *chip, unsigned int offset) { int ret; ret = pm_runtime_get_sync(chip->parent); /* * If the device is already active pm_runtime_get() will return 1 on * success, but gpio_request still needs to return 0. */ return ret < 0 ? ret : 0; } static void xgpio_free(struct gpio_chip *chip, unsigned int offset) { pm_runtime_put(chip->parent); } static int __maybe_unused xgpio_suspend(struct device *dev) { struct xgpio_instance *gpio = dev_get_drvdata(dev); struct irq_data *data = irq_get_irq_data(gpio->irq); if (!data) { dev_dbg(dev, "IRQ not connected\n"); return pm_runtime_force_suspend(dev); } if (!irqd_is_wakeup_set(data)) return pm_runtime_force_suspend(dev); return 0; } /** * xgpio_remove - Remove method for the GPIO device. * @pdev: pointer to the platform device * * This function remove gpiochips and frees all the allocated resources. * * Return: 0 always */ static void xgpio_remove(struct platform_device *pdev) { pm_runtime_get_sync(&pdev->dev); pm_runtime_put_noidle(&pdev->dev); pm_runtime_disable(&pdev->dev); } /** * xgpio_irq_ack - Acknowledge a child GPIO interrupt. * @irq_data: per IRQ and chip data passed down to chip functions * This currently does nothing, but irq_ack is unconditionally called by * handle_edge_irq and therefore must be defined. */ static void xgpio_irq_ack(struct irq_data *irq_data) { } static int __maybe_unused xgpio_resume(struct device *dev) { struct xgpio_instance *gpio = dev_get_drvdata(dev); struct irq_data *data = irq_get_irq_data(gpio->irq); if (!data) { dev_dbg(dev, "IRQ not connected\n"); return pm_runtime_force_resume(dev); } if (!irqd_is_wakeup_set(data)) return pm_runtime_force_resume(dev); return 0; } static int __maybe_unused xgpio_runtime_suspend(struct device *dev) { struct xgpio_instance *gpio = dev_get_drvdata(dev); clk_disable(gpio->clk); return 0; } static int __maybe_unused xgpio_runtime_resume(struct device *dev) { struct xgpio_instance *gpio = dev_get_drvdata(dev); return clk_enable(gpio->clk); } static const struct dev_pm_ops xgpio_dev_pm_ops = { SET_SYSTEM_SLEEP_PM_OPS(xgpio_suspend, xgpio_resume) SET_RUNTIME_PM_OPS(xgpio_runtime_suspend, xgpio_runtime_resume, NULL) }; /** * xgpio_irq_mask - Write the specified signal of the GPIO device. * @irq_data: per IRQ and chip data passed down to chip functions */ static void xgpio_irq_mask(struct irq_data *irq_data) { unsigned long flags; struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data); int irq_offset = irqd_to_hwirq(irq_data); int bit = xgpio_to_bit(chip, irq_offset); u32 mask = BIT(bit / 32), temp; spin_lock_irqsave(&chip->gpio_lock, flags); __clear_bit(bit, chip->enable); if (xgpio_get_value32(chip->enable, bit) == 0) { /* Disable per channel interrupt */ temp = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET); temp &= ~mask; xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, temp); } spin_unlock_irqrestore(&chip->gpio_lock, flags); gpiochip_disable_irq(&chip->gc, irq_offset); } /** * xgpio_irq_unmask - Write the specified signal of the GPIO device. * @irq_data: per IRQ and chip data passed down to chip functions */ static void xgpio_irq_unmask(struct irq_data *irq_data) { unsigned long flags; struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data); int irq_offset = irqd_to_hwirq(irq_data); int bit = xgpio_to_bit(chip, irq_offset); u32 old_enable = xgpio_get_value32(chip->enable, bit); u32 mask = BIT(bit / 32), val; gpiochip_enable_irq(&chip->gc, irq_offset); spin_lock_irqsave(&chip->gpio_lock, flags); __set_bit(bit, chip->enable); if (old_enable == 0) { /* Clear any existing per-channel interrupts */ val = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET); val &= mask; xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, val); /* Update GPIO IRQ read data before enabling interrupt*/ xgpio_read_ch(chip, XGPIO_DATA_OFFSET, bit, chip->last_irq_read); /* Enable per channel interrupt */ val = xgpio_readreg(chip->regs + XGPIO_IPIER_OFFSET); val |= mask; xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, val); } spin_unlock_irqrestore(&chip->gpio_lock, flags); } /** * xgpio_set_irq_type - Write the specified signal of the GPIO device. * @irq_data: Per IRQ and chip data passed down to chip functions * @type: Interrupt type that is to be set for the gpio pin * * Return: * 0 if interrupt type is supported otherwise -EINVAL */ static int xgpio_set_irq_type(struct irq_data *irq_data, unsigned int type) { struct xgpio_instance *chip = irq_data_get_irq_chip_data(irq_data); int irq_offset = irqd_to_hwirq(irq_data); int bit = xgpio_to_bit(chip, irq_offset); /* * The Xilinx GPIO hardware provides a single interrupt status * indication for any state change in a given GPIO channel (bank). * Therefore, only rising edge or falling edge triggers are * supported. */ switch (type & IRQ_TYPE_SENSE_MASK) { case IRQ_TYPE_EDGE_BOTH: __set_bit(bit, chip->rising_edge); __set_bit(bit, chip->falling_edge); break; case IRQ_TYPE_EDGE_RISING: __set_bit(bit, chip->rising_edge); __clear_bit(bit, chip->falling_edge); break; case IRQ_TYPE_EDGE_FALLING: __clear_bit(bit, chip->rising_edge); __set_bit(bit, chip->falling_edge); break; default: return -EINVAL; } irq_set_handler_locked(irq_data, handle_edge_irq); return 0; } /** * xgpio_irqhandler - Gpio interrupt service routine * @desc: Pointer to interrupt description */ static void xgpio_irqhandler(struct irq_desc *desc) { struct xgpio_instance *chip = irq_desc_get_handler_data(desc); struct gpio_chip *gc = &chip->gc; struct irq_chip *irqchip = irq_desc_get_chip(desc); DECLARE_BITMAP(rising, 64); DECLARE_BITMAP(falling, 64); DECLARE_BITMAP(all, 64); int irq_offset; u32 status; u32 bit; status = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET); xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, status); chained_irq_enter(irqchip, desc); spin_lock(&chip->gpio_lock); xgpio_read_ch_all(chip, XGPIO_DATA_OFFSET, all); bitmap_complement(rising, chip->last_irq_read, 64); bitmap_and(rising, rising, all, 64); bitmap_and(rising, rising, chip->enable, 64); bitmap_and(rising, rising, chip->rising_edge, 64); bitmap_complement(falling, all, 64); bitmap_and(falling, falling, chip->last_irq_read, 64); bitmap_and(falling, falling, chip->enable, 64); bitmap_and(falling, falling, chip->falling_edge, 64); bitmap_copy(chip->last_irq_read, all, 64); bitmap_or(all, rising, falling, 64); spin_unlock(&chip->gpio_lock); dev_dbg(gc->parent, "IRQ rising %*pb falling %*pb\n", 64, rising, 64, falling); for_each_set_bit(bit, all, 64) { irq_offset = xgpio_from_bit(chip, bit); generic_handle_domain_irq(gc->irq.domain, irq_offset); } chained_irq_exit(irqchip, desc); } static const struct irq_chip xgpio_irq_chip = { .name = "gpio-xilinx", .irq_ack = xgpio_irq_ack, .irq_mask = xgpio_irq_mask, .irq_unmask = xgpio_irq_unmask, .irq_set_type = xgpio_set_irq_type, .flags = IRQCHIP_IMMUTABLE, GPIOCHIP_IRQ_RESOURCE_HELPERS, }; /** * xgpio_probe - Probe method for the GPIO device. * @pdev: pointer to the platform device * * Return: * It returns 0, if the driver is bound to the GPIO device, or * a negative value if there is an error. */ static int xgpio_probe(struct platform_device *pdev) { struct xgpio_instance *chip; int status = 0; struct device_node *np = pdev->dev.of_node; u32 is_dual = 0; u32 width[2]; u32 state[2]; u32 dir[2]; struct gpio_irq_chip *girq; u32 temp; chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL); if (!chip) return -ENOMEM; platform_set_drvdata(pdev, chip); /* First, check if the device is dual-channel */ of_property_read_u32(np, "xlnx,is-dual", &is_dual); /* Setup defaults */ memset32(width, 0, ARRAY_SIZE(width)); memset32(state, 0, ARRAY_SIZE(state)); memset32(dir, 0xFFFFFFFF, ARRAY_SIZE(dir)); /* Update GPIO state shadow register with default value */ of_property_read_u32(np, "xlnx,dout-default", &state[0]); of_property_read_u32(np, "xlnx,dout-default-2", &state[1]); bitmap_from_arr32(chip->state, state, 64); /* Update GPIO direction shadow register with default value */ of_property_read_u32(np, "xlnx,tri-default", &dir[0]); of_property_read_u32(np, "xlnx,tri-default-2", &dir[1]); bitmap_from_arr32(chip->dir, dir, 64); /* * Check device node and parent device node for device width * and assume default width of 32 */ if (of_property_read_u32(np, "xlnx,gpio-width", &width[0])) width[0] = 32; if (width[0] > 32) return -EINVAL; if (is_dual && of_property_read_u32(np, "xlnx,gpio2-width", &width[1])) width[1] = 32; if (width[1] > 32) return -EINVAL; /* Setup software pin mapping */ bitmap_set(chip->sw_map, 0, width[0] + width[1]); /* Setup hardware pin mapping */ bitmap_set(chip->hw_map, 0, width[0]); bitmap_set(chip->hw_map, 32, width[1]); spin_lock_init(&chip->gpio_lock); chip->gc.base = -1; chip->gc.ngpio = bitmap_weight(chip->hw_map, 64); chip->gc.parent = &pdev->dev; chip->gc.direction_input = xgpio_dir_in; chip->gc.direction_output = xgpio_dir_out; chip->gc.get = xgpio_get; chip->gc.set = xgpio_set; chip->gc.request = xgpio_request; chip->gc.free = xgpio_free; chip->gc.set_multiple = xgpio_set_multiple; chip->gc.label = dev_name(&pdev->dev); chip->regs = devm_platform_ioremap_resource(pdev, 0); if (IS_ERR(chip->regs)) { dev_err(&pdev->dev, "failed to ioremap memory resource\n"); return PTR_ERR(chip->regs); } chip->clk = devm_clk_get_optional_enabled(&pdev->dev, NULL); if (IS_ERR(chip->clk)) return dev_err_probe(&pdev->dev, PTR_ERR(chip->clk), "input clock not found.\n"); pm_runtime_get_noresume(&pdev->dev); pm_runtime_set_active(&pdev->dev); pm_runtime_enable(&pdev->dev); xgpio_save_regs(chip); chip->irq = platform_get_irq_optional(pdev, 0); if (chip->irq <= 0) goto skip_irq; /* Disable per-channel interrupts */ xgpio_writereg(chip->regs + XGPIO_IPIER_OFFSET, 0); /* Clear any existing per-channel interrupts */ temp = xgpio_readreg(chip->regs + XGPIO_IPISR_OFFSET); xgpio_writereg(chip->regs + XGPIO_IPISR_OFFSET, temp); /* Enable global interrupts */ xgpio_writereg(chip->regs + XGPIO_GIER_OFFSET, XGPIO_GIER_IE); girq = &chip->gc.irq; gpio_irq_chip_set_chip(girq, &xgpio_irq_chip); girq->parent_handler = xgpio_irqhandler; girq->num_parents = 1; girq->parents = devm_kcalloc(&pdev->dev, 1, sizeof(*girq->parents), GFP_KERNEL); if (!girq->parents) { status = -ENOMEM; goto err_pm_put; } girq->parents[0] = chip->irq; girq->default_type = IRQ_TYPE_NONE; girq->handler = handle_bad_irq; skip_irq: status = devm_gpiochip_add_data(&pdev->dev, &chip->gc, chip); if (status) { dev_err(&pdev->dev, "failed to add GPIO chip\n"); goto err_pm_put; } pm_runtime_put(&pdev->dev); return 0; err_pm_put: pm_runtime_disable(&pdev->dev); pm_runtime_put_noidle(&pdev->dev); return status; } static const struct of_device_id xgpio_of_match[] = { { .compatible = "xlnx,xps-gpio-1.00.a", }, { /* end of list */ }, }; MODULE_DEVICE_TABLE(of, xgpio_of_match); static struct platform_driver xgpio_plat_driver = { .probe = xgpio_probe, .remove_new = xgpio_remove, .driver = { .name = "gpio-xilinx", .of_match_table = xgpio_of_match, .pm = &xgpio_dev_pm_ops, }, }; static int __init xgpio_init(void) { return platform_driver_register(&xgpio_plat_driver); } subsys_initcall(xgpio_init); static void __exit xgpio_exit(void) { platform_driver_unregister(&xgpio_plat_driver); } module_exit(xgpio_exit); MODULE_AUTHOR("Xilinx, Inc."); MODULE_DESCRIPTION("Xilinx GPIO driver"); MODULE_LICENSE("GPL");