diff options
| author | Guenter Roeck <linux@roeck-us.net> | 2014-01-11 00:17:05 -0800 |
|---|---|---|
| committer | Guenter Roeck <linux@roeck-us.net> | 2014-03-03 08:01:03 -0800 |
| commit | 69e1ded651ee31c8a570d58647902a55806d0db8 (patch) | |
| tree | 26afb63215698900a51901807b66de66028e08f4 /Documentation/hwmon/ltc4260 | |
| parent | 79ffe8594f23475d83112cd5bd68805f91e49170 (diff) | |
| download | linux-69e1ded651ee31c8a570d58647902a55806d0db8.tar.gz linux-69e1ded651ee31c8a570d58647902a55806d0db8.tar.bz2 linux-69e1ded651ee31c8a570d58647902a55806d0db8.zip | |
hwmon: Driver for Linear Technologies LTC4260
LTC4260 is a Positive Voltage Hot Swap Controller.
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Diffstat (limited to 'Documentation/hwmon/ltc4260')
| -rw-r--r-- | Documentation/hwmon/ltc4260 | 56 |
1 files changed, 56 insertions, 0 deletions
diff --git a/Documentation/hwmon/ltc4260 b/Documentation/hwmon/ltc4260 new file mode 100644 index 000000000000..c4ff4ad998b2 --- /dev/null +++ b/Documentation/hwmon/ltc4260 @@ -0,0 +1,56 @@ +Kernel driver ltc4260 +===================== + +Supported chips: + * Linear Technology LTC4260 + Prefix: 'ltc4260' + Addresses scanned: - + Datasheet: + http://cds.linear.com/docs/en/datasheet/4260fc.pdf + +Author: Guenter Roeck <linux@roeck-us.net> + + +Description +----------- + +The LTC4260 Hot Swap controller allows a board to be safely inserted +and removed from a live backplane. + + +Usage Notes +----------- + +This driver does not probe for LTC4260 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC4260 at address 0x10 +on I2C bus #1: +$ modprobe ltc4260 +$ echo ltc4260 0x10 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADC +registers. If a set of voltage divider resistors is installed, calculate the +real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the +value of the divider resistor against the measured voltage and R2 is the value +of the divider resistor against Ground. + +Current reading provided by this driver is reported as obtained from the ADC +Current Sense register. The reported value assumes that a 1 mOhm sense resistor +is installed. If a different sense resistor is installed, calculate the real +current by dividing the reported value by the sense resistor value in mOhm. + +in1_input SOURCE voltage (mV) +in1_min_alarm Undervoltage alarm +in1_max_alarm Overvoltage alarm + +in2_input ADIN voltage (mV) +in2_alarm Power bad alarm + +curr1_input SENSE current (mA) +curr1_alarm SENSE overcurrent alarm |