diff options
author | Guenter Roeck <guenter.roeck@ericsson.com> | 2010-06-25 11:59:54 -0700 |
---|---|---|
committer | Guenter Roeck <guenter.roeck@ericsson.com> | 2010-10-25 14:11:20 -0700 |
commit | e5f5c99a39375ce533aacfdfb269978070121e1c (patch) | |
tree | 0abf39b045d772cf11bc401bcb1a36985ad3d99a /Documentation/hwmon/ltc4261 | |
parent | 2ee321440e3a594dcdd9981e68e5e302447047a2 (diff) | |
download | linux-e5f5c99a39375ce533aacfdfb269978070121e1c.tar.gz linux-e5f5c99a39375ce533aacfdfb269978070121e1c.tar.bz2 linux-e5f5c99a39375ce533aacfdfb269978070121e1c.zip |
hwmon: LTC4261 Hardware monitoring driver
This driver adds support for Linear Technology LTC4261 I2C Negative
Voltage Hot Swap Controller.
Reviewed-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Diffstat (limited to 'Documentation/hwmon/ltc4261')
-rw-r--r-- | Documentation/hwmon/ltc4261 | 63 |
1 files changed, 63 insertions, 0 deletions
diff --git a/Documentation/hwmon/ltc4261 b/Documentation/hwmon/ltc4261 new file mode 100644 index 000000000000..eba2e2c4b94d --- /dev/null +++ b/Documentation/hwmon/ltc4261 @@ -0,0 +1,63 @@ +Kernel driver ltc4261 +===================== + +Supported chips: + * Linear Technology LTC4261 + Prefix: 'ltc4261' + Addresses scanned: - + Datasheet: + http://cds.linear.com/docs/Datasheet/42612fb.pdf + +Author: Guenter Roeck <guenter.roeck@ericsson.com> + + +Description +----------- + +The LTC4261/LTC4261-2 negative voltage Hot Swap controllers allow a board +to be safely inserted and removed from a live backplane. + + +Usage Notes +----------- + +This driver does not probe for LTC4261 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. + +Example: the following will load the driver for an LTC4261 at address 0x10 +on I2C bus #1: +$ modprobe ltc4261 +$ echo ltc4261 0x10 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +Voltage readings provided by this driver are reported as obtained from the ADC +registers. If a set of voltage divider resistors is installed, calculate the +real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the +value of the divider resistor against the measured voltage and R2 is the value +of the divider resistor against Ground. + +Current reading provided by this driver is reported as obtained from the ADC +Current Sense register. The reported value assumes that a 1 mOhm sense resistor +is installed. If a different sense resistor is installed, calculate the real +current by dividing the reported value by the sense resistor value in mOhm. + +The chip has two voltage sensors, but only one set of voltage alarm status bits. +In many many designs, those alarms are associated with the ADIN2 sensor, due to +the proximity of the ADIN2 pin to the OV pin. ADIN2 is, however, not available +on all chip variants. To ensure that the alarm condition is reported to the user, +report it with both voltage sensors. + +in1_input ADIN2 voltage (mV) +in1_min_alarm ADIN/ADIN2 Undervoltage alarm +in1_max_alarm ADIN/ADIN2 Overvoltage alarm + +in2_input ADIN voltage (mV) +in2_min_alarm ADIN/ADIN2 Undervoltage alarm +in2_max_alarm ADIN/ADIN2 Overvoltage alarm + +curr1_input SENSE current (mA) +curr1_alarm SENSE overcurrent alarm |