Fix typos in Documentation/: 'N'-'P'

This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'N'-'P'.

Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>

5 files changed, 13 insertions, 13 deletions

diff --git a/Documentation/networking/gen_stats.txt b/Documentation/networking/gen_stats.txt
index ae54c828f4d6..70e6275b757a 100644
--- a/Documentation/networking/gen_stats.txt
+++ b/Documentation/networking/gen_stats.txt
@@ -79,8 +79,8 @@ Rate Estimator:
 
 0) Prepare an estimator attribute. Most likely this would be in user
    space. The value of this TLV should contain a tc_estimator structure.
-   As usual, such a TLV nees to be 32 bit aligned and therefore the
-   length needs to be appropriately set etc. The estimator interval
+   As usual, such a TLV needs to be 32 bit aligned and therefore the
+   length needs to be appropriately set, etc. The estimator interval
    and ewma log need to be converted to the appropriate values.
    tc_estimator.c::tc_setup_estimator() is advisable to be used as the
    conversion routine. It does a few clever things. It takes a time
diff --git a/Documentation/networking/packet_mmap.txt b/Documentation/networking/packet_mmap.txt
index a87d4a8b3954..12a008a5c221 100644
--- a/Documentation/networking/packet_mmap.txt
+++ b/Documentation/networking/packet_mmap.txt
@@ -278,7 +278,7 @@ an i386 kernel's memory size is limited to 1GiB.
 All memory allocations are not freed until the socket is closed. The memory 
 allocations are done with GFP_KERNEL priority, this basically means that 
 the allocation can wait and swap other process' memory in order to allocate 
-the nececessary memory, so normally limits can be reached.
+the necessary memory, so normally limits can be reached.
 
  Other constraints
 -------------------
diff --git a/Documentation/networking/sk98lin.txt b/Documentation/networking/sk98lin.txt
index b8bc7dd3d282..817fc113d93b 100644
--- a/Documentation/networking/sk98lin.txt
+++ b/Documentation/networking/sk98lin.txt
@@ -180,7 +180,7 @@ To set the driver parameters in this file, proceed as follows:
 1. Insert a line of the form :
    options sk98lin ...
    For "...", the same syntax is required as described for the command
-   line paramaters of modprobe below.
+   line parameters of modprobe below.
 2. To activate the new parameters, either reboot your computer
    or 
    unload and reload the driver.
@@ -364,9 +364,9 @@ Parameter:    IntsPerSec
 Values:       30...40000 (interrupts per second)
 Default:      2000
 
-This parameter is only used, if either static or dynamic interrupt moderation
-is used on a network adapter card. Using this paramter if no moderation is
-applied, will lead to no action performed.
+This parameter is only used if either static or dynamic interrupt moderation
+is used on a network adapter card. Using this parameter if no moderation is
+applied will lead to no action performed.
 
 This parameter determines the length of any interrupt moderation interval. 
 Assuming that static interrupt moderation is to be used, an 'IntsPerSec' 
diff --git a/Documentation/networking/vortex.txt b/Documentation/networking/vortex.txt
index 6091e5f6794f..6356d3faed36 100644
--- a/Documentation/networking/vortex.txt
+++ b/Documentation/networking/vortex.txt
@@ -359,13 +359,13 @@ steps you should take:
 
    Eliminate some variables: try different cards, different
    computers, different cables, different ports on the switch/hub,
-   different versions of the kernel or ofthe driver, etc.
+   different versions of the kernel or of the driver, etc.
 
 - OK, it's a driver problem.
 
    You need to generate a report.  Typically this is an email to the
    maintainer and/or linux-net@vger.kernel.org.  The maintainer's
-   email address will be inthe driver source or in the MAINTAINERS file.
+   email address will be in the driver source or in the MAINTAINERS file.
 
 - The contents of your report will vary a lot depending upon the
   problem.  If it's a kernel crash then you should refer to the
diff --git a/Documentation/networking/wan-router.txt b/Documentation/networking/wan-router.txt
index 37e42fed7485..0cf654147634 100644
--- a/Documentation/networking/wan-router.txt
+++ b/Documentation/networking/wan-router.txt
@@ -214,7 +214,7 @@ PRODUCT COMPONENTS AND RELATED FILES
 /usr/local/wanrouter/patches/kdrivers:
 	Sources of the latest WANPIPE device drivers.
 	These are used to UPGRADE the linux kernel to the newest
-	version if the kernel source has already been pathced with
+	version if the kernel source has already been patched with
 	WANPIPE drivers.
 
 /usr/local/wanrouter/samples:
@@ -438,7 +438,7 @@ beta1-2.1.5 	Nov 15 2000
 				  2.2.X kernels only
 
 				o Secured the driver UDP debugging calls
-					- All illegal netowrk debugging calls are reported to
+					- All illegal network debugging calls are reported to
 					  the log.
 					- Defined a set of allowed commands, all other denied.
 					
@@ -451,7 +451,7 @@ beta1-2.1.5 	Nov 15 2000
 
 				o Keyboard Led Monitor/Debugger
 					- A new utilty /usr/sbin/wpkbdmon uses keyboard leds
-					  to convey operatinal statistic information of the 
+					  to convey operational statistic information of the 
 					  Sangoma WANPIPE cards.
 					NUM_LOCK    = Line State  (On=connected,    Off=disconnected)
 					CAPS_LOCK   = Tx data     (On=transmitting, Off=no tx data)
@@ -470,7 +470,7 @@ beta1-2.1.5 	Nov 15 2000
 				o Fixed the Frame Relay and Chdlc network interfaces so they are
 				  compatible with libpcap libraries.  Meaning, tcpdump, snort,
 				  ethereal, and all other packet sniffers and debuggers work on
-				  all WANPIPE netowrk interfaces.
+				  all WANPIPE network interfaces.
 					- Set the network interface encoding type to ARPHRD_PPP.
 					  This tell the sniffers that data obtained from the
 					  network interface is in pure IP format.