Merge tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Merge "wireless wl12xx and omap device tree changes for v4.1" from Tony
Lindgren:

Wireless and omap changes to make wl12xx driver to use device tree
data instead of platform data from Eliad Peller <eliad@wizery.com>:

- Add device-tree support to the wlcore (wl12xx/wl18xx) driver.

- Update the current users to use the bindings instead of pdata-quirks.

- Finally, remove the deprecated wl12xx_platform_data struct

Note that da850 board file code that still uses the platform data,
but we have da850.dtsi that can be used instead. So it was decided
that we should try to remove the wl12xx support from the da850
board file as suggested by Sekhar Nori <nsekhar@ti.com>. As it's
the last patch in the series, the last patch can be simply reverted
if needed.

As this series touches quite a bit of arch code, it was suggested
by Kalle Valo <kvalo@codeaurora.org> that the whole series should
be merged via the arm-soc tree.

* tag 'omap-for-v4.1/wl12xx-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  wlcore: remove wl12xx_platform_data
  ARM: dts: add wl12xx/wl18xx bindings
  wlcore: add device-tree support
  dt: bindings: add TI's wilink wireless device
  wl12xx: use frequency instead of enumerations for pdata clocks
  wlcore: set irq_trigger in board files instead of hiding behind a quirk
  + Linux 4.0-rc4

Signed-off-by: Olof Johansson <olof@lixom.net>

14 files changed, 175 insertions, 6 deletions

diff --git a/Documentation/CodeOfConflict b/Documentation/CodeOfConflict
new file mode 100644
index 000000000000..1684d0b4efa6
--- /dev/null
+++ b/Documentation/CodeOfConflict
@@ -0,0 +1,27 @@
+Code of Conflict
+----------------
+
+The Linux kernel development effort is a very personal process compared
+to "traditional" ways of developing software.  Your code and ideas
+behind it will be carefully reviewed, often resulting in critique and
+criticism.  The review will almost always require improvements to the
+code before it can be included in the kernel.  Know that this happens
+because everyone involved wants to see the best possible solution for
+the overall success of Linux.  This development process has been proven
+to create the most robust operating system kernel ever, and we do not
+want to do anything to cause the quality of submission and eventual
+result to ever decrease.
+
+If however, anyone feels personally abused, threatened, or otherwise
+uncomfortable due to this process, that is not acceptable.  If so,
+please contact the Linux Foundation's Technical Advisory Board at
+<tab@lists.linux-foundation.org>, or the individual members, and they
+will work to resolve the issue to the best of their ability.  For more
+information on who is on the Technical Advisory Board and what their
+role is, please see:
+	http://www.linuxfoundation.org/programs/advisory-councils/tab
+
+As a reviewer of code, please strive to keep things civil and focused on
+the technical issues involved.  We are all humans, and frustrations can
+be high on both sides of the process.  Try to keep in mind the immortal
+words of Bill and Ted, "Be excellent to each other."
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
index f4445e5a2bbb..1e097037349c 100644
--- a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
+++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt
@@ -22,6 +22,8 @@ Optional Properties:
 	- pclkN, clkN: Pairs of parent of input clock and input clock to the
 		devices in this power domain. Maximum of 4 pairs (N = 0 to 3)
 		are supported currently.
+- power-domains: phandle pointing to the parent power domain, for more details
+		 see Documentation/devicetree/bindings/power/power_domain.txt
 
 Node of a device using power domains must have a power-domains property
 defined with a phandle to respective power domain.
diff --git a/Documentation/devicetree/bindings/arm/sti.txt b/Documentation/devicetree/bindings/arm/sti.txt
index d70ec358736c..8d27f6b084c7 100644
--- a/Documentation/devicetree/bindings/arm/sti.txt
+++ b/Documentation/devicetree/bindings/arm/sti.txt
@@ -13,6 +13,10 @@ Boards with the ST STiH407 SoC shall have the following properties:
 Required root node property:
 compatible = "st,stih407";
 
+Boards with the ST STiH410 SoC shall have the following properties:
+Required root node property:
+compatible = "st,stih410";
+
 Boards with the ST STiH418 SoC shall have the following properties:
 Required root node property:
 compatible = "st,stih418";
diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
index 52d37fd8d3e5..ce4311d726ae 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-imx.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
@@ -7,6 +7,7 @@ Required properties:
   - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC
 - reg : Should contain I2C/HS-I2C registers location and length
 - interrupts : Should contain I2C/HS-I2C interrupt
+- clocks : Should contain the I2C/HS-I2C clock specifier
 
 Optional properties:
 - clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
diff --git a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
index 33df3932168e..8db32384a486 100644
--- a/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
+++ b/Documentation/devicetree/bindings/net/amd-xgbe-phy.txt
@@ -27,6 +27,8 @@ property is used.
 - amd,serdes-cdr-rate: CDR rate speed selection
 - amd,serdes-pq-skew: PQ (data sampling) skew
 - amd,serdes-tx-amp: TX amplitude boost
+- amd,serdes-dfe-tap-config: DFE taps available to run
+- amd,serdes-dfe-tap-enable: DFE taps to enable
 
 Example:
 	xgbe_phy@e1240800 {
@@ -41,4 +43,6 @@ Example:
 		amd,serdes-cdr-rate = <2>, <2>, <7>;
 		amd,serdes-pq-skew = <10>, <10>, <30>;
 		amd,serdes-tx-amp = <15>, <15>, <10>;
+		amd,serdes-dfe-tap-config = <3>, <3>, <1>;
+		amd,serdes-dfe-tap-enable = <0>, <0>, <127>;
 	};
diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
index cfcc52705ed8..6151999c5dca 100644
--- a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
+++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt
@@ -4,7 +4,10 @@ Ethernet nodes are defined to describe on-chip ethernet interfaces in
 APM X-Gene SoC.
 
 Required properties for all the ethernet interfaces:
-- compatible: Should be "apm,xgene-enet"
+- compatible: Should state binding information from the following list,
+  - "apm,xgene-enet":    RGMII based 1G interface
+  - "apm,xgene1-sgenet": SGMII based 1G interface
+  - "apm,xgene1-xgenet": XFI based 10G interface
 - reg: Address and length of the register set for the device. It contains the
   information of registers in the same order as described by reg-names
 - reg-names: Should contain the register set names
diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
new file mode 100644
index 000000000000..2a3d90de18ee
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
@@ -0,0 +1,47 @@
+TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices
+
+This node provides properties for controlling the wilink wireless device. The
+node is expected to be specified as a child node to the SDIO controller that
+connects the device to the system.
+
+Required properties:
+ - compatible: should be one of the following:
+    * "ti,wl1271"
+    * "ti,wl1273"
+    * "ti,wl1281"
+    * "ti,wl1283"
+    * "ti,wl1801"
+    * "ti,wl1805"
+    * "ti,wl1807"
+    * "ti,wl1831"
+    * "ti,wl1835"
+    * "ti,wl1837"
+ - interrupts : specifies attributes for the out-of-band interrupt.
+
+Optional properties:
+ - interrupt-parent : the phandle for the interrupt controller to which the
+	device interrupts are connected.
+ - ref-clock-frequency : ref clock frequency in Hz
+ - tcxo-clock-frequency : tcxo clock frequency in Hz
+
+Note: the *-clock-frequency properties assume internal clocks. In case of external
+clock, new bindings (for parsing the clock nodes) have to be added.
+
+Example:
+
+&mmc3 {
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt
index 98c16672ab5f..0f8ed3710c66 100644
--- a/Documentation/devicetree/bindings/power/power_domain.txt
+++ b/Documentation/devicetree/bindings/power/power_domain.txt
@@ -19,6 +19,16 @@ Required properties:
    providing multiple PM domains (e.g. power controllers), but can be any value
    as specified by device tree binding documentation of particular provider.
 
+Optional properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+   Some power domains might be powered from another power domain (or have
+   other hardware specific dependencies). For representing such dependency
+   a standard PM domain consumer binding is used. When provided, all domains
+   created by the given provider should be subdomains of the domain
+   specified by this binding. More details about power domain specifier are
+   available in the next section.
+
 Example:
 
 	power: power-controller@12340000 {
@@ -30,6 +40,25 @@ Example:
 The node above defines a power controller that is a PM domain provider and
 expects one cell as its phandle argument.
 
+Example 2:
+
+	parent: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12340000 0x1000>;
+		#power-domain-cells = <1>;
+	};
+
+	child: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12341000 0x1000>;
+		power-domains = <&parent 0>;
+		#power-domain-cells = <1>;
+	};
+
+The nodes above define two power controllers: 'parent' and 'child'.
+Domains created by the 'child' power controller are subdomains of '0' power
+domain provided by the 'parent' power controller.
+
 ==PM domain consumers==
 
 Required properties:
diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/8250.txt
index 91d5ab0e60fc..91d5ab0e60fc 100644
--- a/Documentation/devicetree/bindings/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/serial/8250.txt
diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
new file mode 100644
index 000000000000..ebcbb62c0a76
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt
@@ -0,0 +1,19 @@
+ETRAX FS UART
+
+Required properties:
+- compatible : "axis,etraxfs-uart"
+- reg: offset and length of the register set for the device.
+- interrupts: device interrupt
+
+Optional properties:
+- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD
+  line respectively.
+
+Example:
+
+serial@b00260000 {
+	compatible = "axis,etraxfs-uart";
+	reg = <0xb0026000 0x1000>;
+	interrupts = <68>;
+	status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
index 7f76214f728a..289c40ed7470 100644
--- a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
+++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt
@@ -21,6 +21,18 @@ Optional properties:
 - reg-io-width : the size (in bytes) of the IO accesses that should be
   performed on the device.  If this property is not present then single byte
   accesses are used.
+- dcd-override : Override the DCD modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- dsr-override : Override the DTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- cts-override : Override the CTS modem status signal. This signal will always
+  be reported as active instead of being obtained from the modem status
+  register. Define this if your serial port does not use this pin.
+- ri-override : Override the RI modem status signal. This signal will always be
+  reported as inactive instead of being obtained from the modem status register.
+  Define this if your serial port does not use this pin.
 
 Example:
 
@@ -31,6 +43,10 @@ Example:
 		interrupts = <10>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		dcd-override;
+		dsr-override;
+		cts-override;
+		ri-override;
 	};
 
 Example with one clock:
diff --git a/Documentation/devicetree/bindings/submitting-patches.txt b/Documentation/devicetree/bindings/submitting-patches.txt
index 56742bc70218..7d44eae7ab0b 100644
--- a/Documentation/devicetree/bindings/submitting-patches.txt
+++ b/Documentation/devicetree/bindings/submitting-patches.txt
@@ -12,6 +12,9 @@ I. For patch submitters
 
        devicetree@vger.kernel.org
 
+     and Cc: the DT maintainers. Use scripts/get_maintainer.pl to identify
+     all of the DT maintainers.
+
   3) The Documentation/ portion of the patch should come in the series before
      the code implementing the binding.
 
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index f6a9f2593c74..cc393faecc8f 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -20,6 +20,7 @@ amlogic	Amlogic, Inc.
 ams	AMS AG
 amstaos	AMS-Taos Inc.
 apm	Applied Micro Circuits Corporation (APM)
+arasan	Arasan Chip Systems
 arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
 asahi-kasei	Asahi Kasei Corp.
@@ -27,6 +28,7 @@ atmel	Atmel Corporation
 auo	AU Optronics Corporation
 avago	Avago Technologies
 avic	Shanghai AVIC Optoelectronics Co., Ltd.
+axis	Axis Communications AB
 bosch	Bosch Sensortec GmbH
 brcm	Broadcom Corporation
 buffalo	Buffalo, Inc.
diff --git a/Documentation/power/suspend-and-interrupts.txt b/Documentation/power/suspend-and-interrupts.txt
index 2f9c5a5fcb25..8afb29a8604a 100644
--- a/Documentation/power/suspend-and-interrupts.txt
+++ b/Documentation/power/suspend-and-interrupts.txt
@@ -40,8 +40,10 @@ but also to IPIs and to some other special-purpose interrupts.
 
 The IRQF_NO_SUSPEND flag is used to indicate that to the IRQ subsystem when
 requesting a special-purpose interrupt.  It causes suspend_device_irqs() to
-leave the corresponding IRQ enabled so as to allow the interrupt to work all
-the time as expected.
+leave the corresponding IRQ enabled so as to allow the interrupt to work as
+expected during the suspend-resume cycle, but does not guarantee that the
+interrupt will wake the system from a suspended state -- for such cases it is
+necessary to use enable_irq_wake().
 
 Note that the IRQF_NO_SUSPEND flag affects the entire IRQ and not just one
 user of it.  Thus, if the IRQ is shared, all of the interrupt handlers installed
@@ -110,8 +112,9 @@ any special interrupt handling logic for it to work.
 IRQF_NO_SUSPEND and enable_irq_wake()
 -------------------------------------
 
-There are no valid reasons to use both enable_irq_wake() and the IRQF_NO_SUSPEND
-flag on the same IRQ.
+There are very few valid reasons to use both enable_irq_wake() and the
+IRQF_NO_SUSPEND flag on the same IRQ, and it is never valid to use both for the
+same device.
 
 First of all, if the IRQ is not shared, the rules for handling IRQF_NO_SUSPEND
 interrupts (interrupt handlers are invoked after suspend_device_irqs()) are
@@ -120,4 +123,13 @@ handlers are not invoked after suspend_device_irqs()).
 
 Second, both enable_irq_wake() and IRQF_NO_SUSPEND apply to entire IRQs and not
 to individual interrupt handlers, so sharing an IRQ between a system wakeup
-interrupt source and an IRQF_NO_SUSPEND interrupt source does not make sense.
+interrupt source and an IRQF_NO_SUSPEND interrupt source does not generally
+make sense.
+
+In rare cases an IRQ can be shared between a wakeup device driver and an
+IRQF_NO_SUSPEND user. In order for this to be safe, the wakeup device driver
+must be able to discern spurious IRQs from genuine wakeup events (signalling
+the latter to the core with pm_system_wakeup()), must use enable_irq_wake() to
+ensure that the IRQ will function as a wakeup source, and must request the IRQ
+with IRQF_COND_SUSPEND to tell the core that it meets these requirements. If
+these requirements are not met, it is not valid to use IRQF_COND_SUSPEND.