Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus

ASoC: Updates for v4.13

The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:

 - The of-graph card, finally merged after a long and dedicated effort
   by Morimoto-san.
 - New widget types intended mainly for use with DSPs.
 - New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
   of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
   controllers and ZTE AUD96P22 CODECs.

40 files changed, 1586 insertions, 417 deletions

diff --git a/Documentation/acpi/acpi-lid.txt b/Documentation/acpi/acpi-lid.txt
index 22cb3091f297..effe7af3a5af 100644
--- a/Documentation/acpi/acpi-lid.txt
+++ b/Documentation/acpi/acpi-lid.txt
@@ -59,20 +59,28 @@ button driver uses the following 3 modes in order not to trigger issues.
 If the userspace hasn't been prepared to ignore the unreliable "opened"
 events and the unreliable initial state notification, Linux users can use
 the following kernel parameters to handle the possible issues:
-A. button.lid_init_state=open:
+A. button.lid_init_state=method:
+   When this option is specified, the ACPI button driver reports the
+   initial lid state using the returning value of the _LID control method
+   and whether the "opened"/"closed" events are paired fully relies on the
+   firmware implementation.
+   This option can be used to fix some platforms where the returning value
+   of the _LID control method is reliable but the initial lid state
+   notification is missing.
+   This option is the default behavior during the period the userspace
+   isn't ready to handle the buggy AML tables.
+B. button.lid_init_state=open:
    When this option is specified, the ACPI button driver always reports the
    initial lid state as "opened" and whether the "opened"/"closed" events
    are paired fully relies on the firmware implementation.
    This may fix some platforms where the returning value of the _LID
    control method is not reliable and the initial lid state notification is
    missing.
-   This option is the default behavior during the period the userspace
-   isn't ready to handle the buggy AML tables.
 
 If the userspace has been prepared to ignore the unreliable "opened" events
 and the unreliable initial state notification, Linux users should always
 use the following kernel parameter:
-B. button.lid_init_state=ignore:
+C. button.lid_init_state=ignore:
    When this option is specified, the ACPI button driver never reports the
    initial lid state and there is a compensation mechanism implemented to
    ensure that the reliable "closed" notifications can always be delievered
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt
index 15f79c27748d..7737ab5d04b2 100644
--- a/Documentation/admin-guide/kernel-parameters.txt
+++ b/Documentation/admin-guide/kernel-parameters.txt
@@ -866,6 +866,15 @@
 
 	dscc4.setup=	[NET]
 
+	dt_cpu_ftrs=	[PPC]
+			Format: {"off" | "known"}
+			Control how the dt_cpu_ftrs device-tree binding is
+			used for CPU feature discovery and setup (if it
+			exists).
+			off: Do not use it, fall back to legacy cpu table.
+			known: Do not pass through unknown features to guests
+			or userspace, only those that the kernel is aware of.
+
 	dump_apple_properties	[X86]
 			Dump name and content of EFI device properties on
 			x86 Macs.  Useful for driver authors to determine
@@ -3802,6 +3811,13 @@
 			expediting.  Set to zero to disable automatic
 			expediting.
 
+	stack_guard_gap=	[MM]
+			override the default stack gap protection. The value
+			is in page units and it defines how many pages prior
+			to (for stacks growing down) resp. after (for stacks
+			growing up) the main stack are reserved for no other
+			mapping. Default value is 256 pages.
+
 	stacktrace	[FTRACE]
 			Enabled the stack tracer on boot up.
 
diff --git a/Documentation/admin-guide/pm/cpufreq.rst b/Documentation/admin-guide/pm/cpufreq.rst
index 289c80f7760e..09aa2e949787 100644
--- a/Documentation/admin-guide/pm/cpufreq.rst
+++ b/Documentation/admin-guide/pm/cpufreq.rst
@@ -1,4 +1,5 @@
 .. |struct cpufreq_policy| replace:: :c:type:`struct cpufreq_policy <cpufreq_policy>`
+.. |intel_pstate| replace:: :doc:`intel_pstate <intel_pstate>`
 
 =======================
 CPU Performance Scaling
@@ -75,7 +76,7 @@ feedback registers, as that information is typically specific to the hardware
 interface it comes from and may not be easily represented in an abstract,
 platform-independent way.  For this reason, ``CPUFreq`` allows scaling drivers
 to bypass the governor layer and implement their own performance scaling
-algorithms.  That is done by the ``intel_pstate`` scaling driver.
+algorithms.  That is done by the |intel_pstate| scaling driver.
 
 
 ``CPUFreq`` Policy Objects
@@ -174,13 +175,13 @@ necessary to restart the scaling governor so that it can take the new online CPU
 into account.  That is achieved by invoking the governor's ``->stop`` and
 ``->start()`` callbacks, in this order, for the entire policy.
 
-As mentioned before, the ``intel_pstate`` scaling driver bypasses the scaling
+As mentioned before, the |intel_pstate| scaling driver bypasses the scaling
 governor layer of ``CPUFreq`` and provides its own P-state selection algorithms.
-Consequently, if ``intel_pstate`` is used, scaling governors are not attached to
+Consequently, if |intel_pstate| is used, scaling governors are not attached to
 new policy objects.  Instead, the driver's ``->setpolicy()`` callback is invoked
 to register per-CPU utilization update callbacks for each policy.  These
 callbacks are invoked by the CPU scheduler in the same way as for scaling
-governors, but in the ``intel_pstate`` case they both determine the P-state to
+governors, but in the |intel_pstate| case they both determine the P-state to
 use and change the hardware configuration accordingly in one go from scheduler
 context.
 
@@ -257,7 +258,7 @@ are the following:
 
 ``scaling_available_governors``
 	List of ``CPUFreq`` scaling governors present in the kernel that can
-	be attached to this policy or (if the ``intel_pstate`` scaling driver is
+	be attached to this policy or (if the |intel_pstate| scaling driver is
 	in use) list of scaling algorithms provided by the driver that can be
 	applied to this policy.
 
@@ -274,7 +275,7 @@ are the following:
 	the CPU is actually running at (due to hardware design and other
 	limitations).
 
-	Some scaling drivers (e.g. ``intel_pstate``) attempt to provide
+	Some scaling drivers (e.g. |intel_pstate|) attempt to provide
 	information more precisely reflecting the current CPU frequency through
 	this attribute, but that still may not be the exact current CPU
 	frequency as seen by the hardware at the moment.
@@ -284,13 +285,13 @@ are the following:
 
 ``scaling_governor``
 	The scaling governor currently attached to this policy or (if the
-	``intel_pstate`` scaling driver is in use) the scaling algorithm
+	|intel_pstate| scaling driver is in use) the scaling algorithm
 	provided by the driver that is currently applied to this policy.
 
 	This attribute is read-write and writing to it will cause a new scaling
 	governor to be attached to this policy or a new scaling algorithm
 	provided by the scaling driver to be applied to it (in the
-	``intel_pstate`` case), as indicated by the string written to this
+	|intel_pstate| case), as indicated by the string written to this
 	attribute (which must be one of the names listed by the
 	``scaling_available_governors`` attribute described above).
 
@@ -619,7 +620,7 @@ This file is located under :file:`/sys/devices/system/cpu/cpufreq/` and controls
 the "boost" setting for the whole system.  It is not present if the underlying
 scaling driver does not support the frequency boost mechanism (or supports it,
 but provides a driver-specific interface for controlling it, like
-``intel_pstate``).
+|intel_pstate|).
 
 If the value in this file is 1, the frequency boost mechanism is enabled.  This
 means that either the hardware can be put into states in which it is able to
diff --git a/Documentation/admin-guide/pm/index.rst b/Documentation/admin-guide/pm/index.rst
index c80f087321fc..7f148f76f432 100644
--- a/Documentation/admin-guide/pm/index.rst
+++ b/Documentation/admin-guide/pm/index.rst
@@ -6,6 +6,7 @@ Power Management
    :maxdepth: 2
 
    cpufreq
+   intel_pstate
 
 .. only::  subproject and html
 
diff --git a/Documentation/admin-guide/pm/intel_pstate.rst b/Documentation/admin-guide/pm/intel_pstate.rst
new file mode 100644
index 000000000000..33d703989ea8
--- /dev/null
+++ b/Documentation/admin-guide/pm/intel_pstate.rst
@@ -0,0 +1,755 @@
+===============================================
+``intel_pstate`` CPU Performance Scaling Driver
+===============================================
+
+::
+
+ Copyright (c) 2017 Intel Corp., Rafael J. Wysocki <rafael.j.wysocki@intel.com>
+
+
+General Information
+===================
+
+``intel_pstate`` is a part of the
+:doc:`CPU performance scaling subsystem <cpufreq>` in the Linux kernel
+(``CPUFreq``).  It is a scaling driver for the Sandy Bridge and later
+generations of Intel processors.  Note, however, that some of those processors
+may not be supported.  [To understand ``intel_pstate`` it is necessary to know
+how ``CPUFreq`` works in general, so this is the time to read :doc:`cpufreq` if
+you have not done that yet.]
+
+For the processors supported by ``intel_pstate``, the P-state concept is broader
+than just an operating frequency or an operating performance point (see the
+`LinuxCon Europe 2015 presentation by Kristen Accardi <LCEU2015_>`_ for more
+information about that).  For this reason, the representation of P-states used
+by ``intel_pstate`` internally follows the hardware specification (for details
+refer to `Intel® 64 and IA-32 Architectures Software Developer’s Manual
+Volume 3: System Programming Guide <SDM_>`_).  However, the ``CPUFreq`` core
+uses frequencies for identifying operating performance points of CPUs and
+frequencies are involved in the user space interface exposed by it, so
+``intel_pstate`` maps its internal representation of P-states to frequencies too
+(fortunately, that mapping is unambiguous).  At the same time, it would not be
+practical for ``intel_pstate`` to supply the ``CPUFreq`` core with a table of
+available frequencies due to the possible size of it, so the driver does not do
+that.  Some functionality of the core is limited by that.
+
+Since the hardware P-state selection interface used by ``intel_pstate`` is
+available at the logical CPU level, the driver always works with individual
+CPUs.  Consequently, if ``intel_pstate`` is in use, every ``CPUFreq`` policy
+object corresponds to one logical CPU and ``CPUFreq`` policies are effectively
+equivalent to CPUs.  In particular, this means that they become "inactive" every
+time the corresponding CPU is taken offline and need to be re-initialized when
+it goes back online.
+
+``intel_pstate`` is not modular, so it cannot be unloaded, which means that the
+only way to pass early-configuration-time parameters to it is via the kernel
+command line.  However, its configuration can be adjusted via ``sysfs`` to a
+great extent.  In some configurations it even is possible to unregister it via
+``sysfs`` which allows another ``CPUFreq`` scaling driver to be loaded and
+registered (see `below <status_attr_>`_).
+
+
+Operation Modes
+===============
+
+``intel_pstate`` can operate in three different modes: in the active mode with
+or without hardware-managed P-states support and in the passive mode.  Which of
+them will be in effect depends on what kernel command line options are used and
+on the capabilities of the processor.
+
+Active Mode
+-----------
+
+This is the default operation mode of ``intel_pstate``.  If it works in this
+mode, the ``scaling_driver`` policy attribute in ``sysfs`` for all ``CPUFreq``
+policies contains the string "intel_pstate".
+
+In this mode the driver bypasses the scaling governors layer of ``CPUFreq`` and
+provides its own scaling algorithms for P-state selection.  Those algorithms
+can be applied to ``CPUFreq`` policies in the same way as generic scaling
+governors (that is, through the ``scaling_governor`` policy attribute in
+``sysfs``).  [Note that different P-state selection algorithms may be chosen for
+different policies, but that is not recommended.]
+
+They are not generic scaling governors, but their names are the same as the
+names of some of those governors.  Moreover, confusingly enough, they generally
+do not work in the same way as the generic governors they share the names with.
+For example, the ``powersave`` P-state selection algorithm provided by
+``intel_pstate`` is not a counterpart of the generic ``powersave`` governor
+(roughly, it corresponds to the ``schedutil`` and ``ondemand`` governors).
+
+There are two P-state selection algorithms provided by ``intel_pstate`` in the
+active mode: ``powersave`` and ``performance``.  The way they both operate
+depends on whether or not the hardware-managed P-states (HWP) feature has been
+enabled in the processor and possibly on the processor model.
+
+Which of the P-state selection algorithms is used by default depends on the
+:c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE` kernel configuration option.
+Namely, if that option is set, the ``performance`` algorithm will be used by
+default, and the other one will be used by default if it is not set.
+
+Active Mode With HWP
+~~~~~~~~~~~~~~~~~~~~
+
+If the processor supports the HWP feature, it will be enabled during the
+processor initialization and cannot be disabled after that.  It is possible
+to avoid enabling it by passing the ``intel_pstate=no_hwp`` argument to the
+kernel in the command line.
+
+If the HWP feature has been enabled, ``intel_pstate`` relies on the processor to
+select P-states by itself, but still it can give hints to the processor's
+internal P-state selection logic.  What those hints are depends on which P-state
+selection algorithm has been applied to the given policy (or to the CPU it
+corresponds to).
+
+Even though the P-state selection is carried out by the processor automatically,
+``intel_pstate`` registers utilization update callbacks with the CPU scheduler
+in this mode.  However, they are not used for running a P-state selection
+algorithm, but for periodic updates of the current CPU frequency information to
+be made available from the ``scaling_cur_freq`` policy attribute in ``sysfs``.
+
+HWP + ``performance``
+.....................
+
+In this configuration ``intel_pstate`` will write 0 to the processor's
+Energy-Performance Preference (EPP) knob (if supported) or its
+Energy-Performance Bias (EPB) knob (otherwise), which means that the processor's
+internal P-state selection logic is expected to focus entirely on performance.
+
+This will override the EPP/EPB setting coming from the ``sysfs`` interface
+(see `Energy vs Performance Hints`_ below).
+
+Also, in this configuration the range of P-states available to the processor's
+internal P-state selection logic is always restricted to the upper boundary
+(that is, the maximum P-state that the driver is allowed to use).
+
+HWP + ``powersave``
+...................
+
+In this configuration ``intel_pstate`` will set the processor's
+Energy-Performance Preference (EPP) knob (if supported) or its
+Energy-Performance Bias (EPB) knob (otherwise) to whatever value it was
+previously set to via ``sysfs`` (or whatever default value it was
+set to by the platform firmware).  This usually causes the processor's
+internal P-state selection logic to be less performance-focused.
+
+Active Mode Without HWP
+~~~~~~~~~~~~~~~~~~~~~~~
+
+This is the default operation mode for processors that do not support the HWP
+feature.  It also is used by default with the ``intel_pstate=no_hwp`` argument
+in the kernel command line.  However, in this mode ``intel_pstate`` may refuse
+to work with the given processor if it does not recognize it.  [Note that
+``intel_pstate`` will never refuse to work with any processor with the HWP
+feature enabled.]
+
+In this mode ``intel_pstate`` registers utilization update callbacks with the
+CPU scheduler in order to run a P-state selection algorithm, either
+``powersave`` or ``performance``, depending on the ``scaling_cur_freq`` policy
+setting in ``sysfs``.  The current CPU frequency information to be made
+available from the ``scaling_cur_freq`` policy attribute in ``sysfs`` is
+periodically updated by those utilization update callbacks too.
+
+``performance``
+...............
+
+Without HWP, this P-state selection algorithm is always the same regardless of
+the processor model and platform configuration.
+
+It selects the maximum P-state it is allowed to use, subject to limits set via
+``sysfs``, every time the P-state selection computations are carried out by the
+driver's utilization update callback for the given CPU (that does not happen
+more often than every 10 ms), but the hardware configuration will not be changed
+if the new P-state is the same as the current one.
+
+This is the default P-state selection algorithm if the
+:c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE` kernel configuration option
+is set.
+
+``powersave``
+.............
+
+Without HWP, this P-state selection algorithm generally depends on the
+processor model and/or the system profile setting in the ACPI tables and there
+are two variants of it.
+
+One of them is used with processors from the Atom line and (regardless of the
+processor model) on platforms with the system profile in the ACPI tables set to
+"mobile" (laptops mostly), "tablet", "appliance PC", "desktop", or
+"workstation".  It is also used with processors supporting the HWP feature if
+that feature has not been enabled (that is, with the ``intel_pstate=no_hwp``
+argument in the kernel command line).  It is similar to the algorithm
+implemented by the generic ``schedutil`` scaling governor except that the
+utilization metric used by it is based on numbers coming from feedback
+registers of the CPU.  It generally selects P-states proportional to the
+current CPU utilization, so it is referred to as the "proportional" algorithm.
+
+The second variant of the ``powersave`` P-state selection algorithm, used in all
+of the other cases (generally, on processors from the Core line, so it is
+referred to as the "Core" algorithm), is based on the values read from the APERF
+and MPERF feedback registers and the previously requested target P-state.
+It does not really take CPU utilization into account explicitly, but as a rule
+it causes the CPU P-state to ramp up very quickly in response to increased
+utilization which is generally desirable in server environments.
+
+Regardless of the variant, this algorithm is run by the driver's utilization
+update callback for the given CPU when it is invoked by the CPU scheduler, but
+not more often than every 10 ms (that can be tweaked via ``debugfs`` in `this
+particular case <Tuning Interface in debugfs_>`_).  Like in the ``performance``
+case, the hardware configuration is not touched if the new P-state turns out to
+be the same as the current one.
+
+This is the default P-state selection algorithm if the
+:c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE` kernel configuration option
+is not set.
+
+Passive Mode
+------------
+
+This mode is used if the ``intel_pstate=passive`` argument is passed to the
+kernel in the command line (it implies the ``intel_pstate=no_hwp`` setting too).
+Like in the active mode without HWP support, in this mode ``intel_pstate`` may
+refuse to work with the given processor if it does not recognize it.
+
+If the driver works in this mode, the ``scaling_driver`` policy attribute in
+``sysfs`` for all ``CPUFreq`` policies contains the string "intel_cpufreq".
+Then, the driver behaves like a regular ``CPUFreq`` scaling driver.  That is,
+it is invoked by generic scaling governors when necessary to talk to the
+hardware in order to change the P-state of a CPU (in particular, the
+``schedutil`` governor can invoke it directly from scheduler context).
+
+While in this mode, ``intel_pstate`` can be used with all of the (generic)
+scaling governors listed by the ``scaling_available_governors`` policy attribute
+in ``sysfs`` (and the P-state selection algorithms described above are not
+used).  Then, it is responsible for the configuration of policy objects
+corresponding to CPUs and provides the ``CPUFreq`` core (and the scaling
+governors attached to the policy objects) with accurate information on the
+maximum and minimum operating frequencies supported by the hardware (including
+the so-called "turbo" frequency ranges).  In other words, in the passive mode
+the entire range of available P-states is exposed by ``intel_pstate`` to the
+``CPUFreq`` core.  However, in this mode the driver does not register
+utilization update callbacks with the CPU scheduler and the ``scaling_cur_freq``
+information comes from the ``CPUFreq`` core (and is the last frequency selected
+by the current scaling governor for the given policy).
+
+
+.. _turbo:
+
+Turbo P-states Support
+======================
+
+In the majority of cases, the entire range of P-states available to
+``intel_pstate`` can be divided into two sub-ranges that correspond to
+different types of processor behavior, above and below a boundary that
+will be referred to as the "turbo threshold" in what follows.
+
+The P-states above the turbo threshold are referred to as "turbo P-states" and
+the whole sub-range of P-states they belong to is referred to as the "turbo
+range".  These names are related to the Turbo Boost technology allowing a
+multicore processor to opportunistically increase the P-state of one or more
+cores if there is enough power to do that and if that is not going to cause the
+thermal envelope of the processor package to be exceeded.
+
+Specifically, if software sets the P-state of a CPU core within the turbo range
+(that is, above the turbo threshold), the processor is permitted to take over
+performance scaling control for that core and put it into turbo P-states of its
+choice going forward.  However, that permission is interpreted differently by
+different processor generations.  Namely, the Sandy Bridge generation of
+processors will never use any P-states above the last one set by software for
+the given core, even if it is within the turbo range, whereas all of the later
+processor generations will take it as a license to use any P-states from the
+turbo range, even above the one set by software.  In other words, on those
+processors setting any P-state from the turbo range will enable the processor
+to put the given core into all turbo P-states up to and including the maximum
+supported one as it sees fit.
+
+One important property of turbo P-states is that they are not sustainable.  More
+precisely, there is no guarantee that any CPUs will be able to stay in any of
+those states indefinitely, because the power distribution within the processor
+package may change over time  or the thermal envelope it was designed for might
+be exceeded if a turbo P-state was used for too long.
+
+In turn, the P-states below the turbo threshold generally are sustainable.  In
+fact, if one of them is set by software, the processor is not expected to change
+it to a lower one unless in a thermal stress or a power limit violation
+situation (a higher P-state may still be used if it is set for another CPU in
+the same package at the same time, for example).
+
+Some processors allow multiple cores to be in turbo P-states at the same time,
+but the maximum P-state that can be set for them generally depends on the number
+of cores running concurrently.  The maximum turbo P-state that can be set for 3
+cores at the same time usually is lower than the analogous maximum P-state for
+2 cores, which in turn usually is lower than the maximum turbo P-state that can
+be set for 1 core.  The one-core maximum turbo P-state is thus the maximum
+supported one overall.
+
+The maximum supported turbo P-state, the turbo threshold (the maximum supported
+non-turbo P-state) and the minimum supported P-state are specific to the
+processor model and can be determined by reading the processor's model-specific
+registers (MSRs).  Moreover, some processors support the Configurable TDP
+(Thermal Design Power) feature and, when that feature is enabled, the turbo
+threshold effectively becomes a configurable value that can be set by the
+platform firmware.
+
+Unlike ``_PSS`` objects in the ACPI tables, ``intel_pstate`` always exposes
+the entire range of available P-states, including the whole turbo range, to the
+``CPUFreq`` core and (in the passive mode) to generic scaling governors.  This
+generally causes turbo P-states to be set more often when ``intel_pstate`` is
+used relative to ACPI-based CPU performance scaling (see `below <acpi-cpufreq_>`_
+for more information).
+
+Moreover, since ``intel_pstate`` always knows what the real turbo threshold is
+(even if the Configurable TDP feature is enabled in the processor), its
+``no_turbo`` attribute in ``sysfs`` (described `below <no_turbo_attr_>`_) should
+work as expected in all cases (that is, if set to disable turbo P-states, it
+always should prevent ``intel_pstate`` from using them).
+
+
+Processor Support
+=================
+
+To handle a given processor ``intel_pstate`` requires a number of different
+pieces of information on it to be known, including:
+
+ * The minimum supported P-state.
+
+ * The maximum supported `non-turbo P-state <turbo_>`_.
+
+ * Whether or not turbo P-states are supported at all.
+
+ * The maximum supported `one-core turbo P-state <turbo_>`_ (if turbo P-states
+   are supported).
+
+ * The scaling formula to translate the driver's internal representation
+   of P-states into frequencies and the other way around.
+
+Generally, ways to obtain that information are specific to the processor model
+or family.  Although it often is possible to obtain all of it from the processor
+itself (using model-specific registers), there are cases in which hardware
+manuals need to be consulted to get to it too.
+
+For this reason, there is a list of supported processors in ``intel_pstate`` and
+the driver initialization will fail if the detected processor is not in that
+list, unless it supports the `HWP feature <Active Mode_>`_.  [The interface to
+obtain all of the information listed above is the same for all of the processors
+supporting the HWP feature, which is why they all are supported by
+``intel_pstate``.]
+
+
+User Space Interface in ``sysfs``
+=================================
+
+Global Attributes
+-----------------
+
+``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
+control its functionality at the system level.  They are located in the
+``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
+CPUs.
+
+Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
+argument is passed to the kernel in the command line.
+
+``max_perf_pct``
+	Maximum P-state the driver is allowed to set in percent of the
+	maximum supported performance level (the highest supported `turbo
+	P-state <turbo_>`_).
+
+	This attribute will not be exposed if the
+	``intel_pstate=per_cpu_perf_limits`` argument is present in the kernel
+	command line.
+
+``min_perf_pct``
+	Minimum P-state the driver is allowed to set in percent of the
+	maximum supported performance level (the highest supported `turbo
+	P-state <turbo_>`_).
+
+	This attribute will not be exposed if the
+	``intel_pstate=per_cpu_perf_limits`` argument is present in the kernel
+	command line.
+
+``num_pstates``
+	Number of P-states supported by the processor (between 0 and 255
+	inclusive) including both turbo and non-turbo P-states (see
+	`Turbo P-states Support`_).
+
+	The value of this attribute is not affected by the ``no_turbo``
+	setting described `below <no_turbo_attr_>`_.
+
+	This attribute is read-only.
+
+``turbo_pct``
+	Ratio of the `turbo range <turbo_>`_ size to the size of the entire
+	range of supported P-states, in percent.
+
+	This attribute is read-only.
+
+.. _no_turbo_attr:
+
+``no_turbo``
+	If set (equal to 1), the driver is not allowed to set any turbo P-states
+	(see `Turbo P-states Support`_).  If unset (equalt to 0, which is the
+	default), turbo P-states can be set by the driver.
+	[Note that ``intel_pstate`` does not support the general ``boost``
+	attribute (supported by some other scaling drivers) which is replaced
+	by this one.]
+
+	This attrubute does not affect the maximum supported frequency value
+	supplied to the ``CPUFreq`` core and exposed via the policy interface,
+	but it affects the maximum possible value of per-policy P-state	limits
+	(see `Interpretation of Policy Attributes`_ below for details).
+
+.. _status_attr:
+
+``status``
+	Operation mode of the driver: "active", "passive" or "off".
+
+	"active"
+		The driver is functional and in the `active mode
+		<Active Mode_>`_.
+
+	"passive"
+		The driver is functional and in the `passive mode
+		<Passive Mode_>`_.
+
+	"off"
+		The driver is not functional (it is not registered as a scaling
+		driver with the ``CPUFreq`` core).
+
+	This attribute can be written to in order to change the driver's
+	operation mode or to unregister it.  The string written to it must be
+	one of the possible values of it and, if successful, the write will
+	cause the driver to switch over to the operation mode represented by
+	that string - or to be unregistered in the "off" case.  [Actually,
+	switching over from the active mode to the passive mode or the other
+	way around causes the driver to be unregistered and registered again
+	with a different set of callbacks, so all of its settings (the global
+	as well as the per-policy ones) are then reset to their default
+	values, possibly depending on the target operation mode.]
+
+	That only is supported in some configurations, though (for example, if
+	the `HWP feature is enabled in the processor <Active Mode With HWP_>`_,
+	the operation mode of the driver cannot be changed), and if it is not
+	supported in the current configuration, writes to this attribute with
+	fail with an appropriate error.
+
+Interpretation of Policy Attributes
+-----------------------------------
+
+The interpretation of some ``CPUFreq`` policy attributes described in
+:doc:`cpufreq` is special with ``intel_pstate`` as the current scaling driver
+and it generally depends on the driver's `operation mode <Operation Modes_>`_.
+
+First of all, the values of the ``cpuinfo_max_freq``, ``cpuinfo_min_freq`` and
+``scaling_cur_freq`` attributes are produced by applying a processor-specific
+multiplier to the internal P-state representation used by ``intel_pstate``.
+Also, the values of the ``scaling_max_freq`` and ``scaling_min_freq``
+attributes are capped by the frequency corresponding to the maximum P-state that
+the driver is allowed to set.
+
+If the ``no_turbo`` `global attribute <no_turbo_attr_>`_ is set, the driver is
+not allowed to use turbo P-states, so the maximum value of ``scaling_max_freq``
+and ``scaling_min_freq`` is limited to the maximum non-turbo P-state frequency.
+Accordingly, setting ``no_turbo`` causes ``scaling_max_freq`` and
+``scaling_min_freq`` to go down to that value if they were above it before.
+However, the old values of ``scaling_max_freq`` and ``scaling_min_freq`` will be
+restored after unsetting ``no_turbo``, unless these attributes have been written
+to after ``no_turbo`` was set.
+
+If ``no_turbo`` is not set, the maximum possible value of ``scaling_max_freq``
+and ``scaling_min_freq`` corresponds to the maximum supported turbo P-state,
+which also is the value of ``cpuinfo_max_freq`` in either case.
+
+Next, the following policy attributes have special meaning if
+``intel_pstate`` works in the `active mode <Active Mode_>`_:
+
+``scaling_available_governors``
+	List of P-state selection algorithms provided by ``intel_pstate``.
+
+``scaling_governor``
+	P-state selection algorithm provided by ``intel_pstate`` currently in
+	use with the given policy.
+
+``scaling_cur_freq``
+	Frequency of the average P-state of the CPU represented by the given
+	policy for the time interval between the last two invocations of the
+	driver's utilization update callback by the CPU scheduler for that CPU.
+
+The meaning of these attributes in the `passive mode <Passive Mode_>`_ is the
+same as for other scaling drivers.
+
+Additionally, the value of the ``scaling_driver`` attribute for ``intel_pstate``
+depends on the operation mode of the driver.  Namely, it is either
+"intel_pstate" (in the `active mode <Active Mode_>`_) or "intel_cpufreq" (in the
+`passive mode <Passive Mode_>`_).
+
+Coordination of P-State Limits
+------------------------------
+
+``intel_pstate`` allows P-state limits to be set in two ways: with the help of
+the ``max_perf_pct`` and ``min_perf_pct`` `global attributes
+<Global Attributes_>`_ or via the ``scaling_max_freq`` and ``scaling_min_freq``
+``CPUFreq`` policy attributes.  The coordination between those limits is based
+on the following rules, regardless of the current operation mode of the driver:
+
+ 1. All CPUs are affected by the global limits (that is, none of them can be
+    requested to run faster than the global maximum and none of them can be
+    requested to run slower than the global minimum).
+
+ 2. Each individual CPU is affected by its own per-policy limits (that is, it
+    cannot be requested to run faster than its own per-policy maximum and it
+    cannot be requested to run slower than its own per-policy minimum).
+
+ 3. The global and per-policy limits can be set independently.
+
+If the `HWP feature is enabled in the processor <Active Mode With HWP_>`_, the
+resulting effective values are written into its registers whenever the limits
+change in order to request its internal P-state selection logic to always set
+P-states within these limits.  Otherwise, the limits are taken into account by
+scaling governors (in the `passive mode <Passive Mode_>`_) and by the driver
+every time before setting a new P-state for a CPU.
+
+Additionally, if the ``intel_pstate=per_cpu_perf_limits`` command line argument
+is passed to the kernel, ``max_perf_pct`` and ``min_perf_pct`` are not exposed
+at all and the only way to set the limits is by using the policy attributes.
+
+
+Energy vs Performance Hints
+---------------------------
+
+If ``intel_pstate`` works in the `active mode with the HWP feature enabled
+<Active Mode With HWP_>`_ in the processor, additional attributes are present
+in every ``CPUFreq`` policy directory in ``sysfs``.  They are intended to allow
+user space to help ``intel_pstate`` to adjust the processor's internal P-state
+selection logic by focusing it on performance or on energy-efficiency, or
+somewhere between the two extremes:
+
+``energy_performance_preference``
+	Current value of the energy vs performance hint for the given policy
+	(or the CPU represented by it).
+
+	The hint can be changed by writing to this attribute.
+
+``energy_performance_available_preferences``
+	List of strings that can be written to the
+	``energy_performance_preference`` attribute.
+
+	They represent different energy vs performance hints and should be
+	self-explanatory, except that ``default`` represents whatever hint
+	value was set by the platform firmware.
+
+Strings written to the ``energy_performance_preference`` attribute are
+internally translated to integer values written to the processor's
+Energy-Performance Preference (EPP) knob (if supported) or its
+Energy-Performance Bias (EPB) knob.
+
+[Note that tasks may by migrated from one CPU to another by the scheduler's
+load-balancing algorithm and if different energy vs performance hints are
+set for those CPUs, that may lead to undesirable outcomes.  To avoid such
+issues it is better to set the same energy vs performance hint for all CPUs
+or to pin every task potentially sensitive to them to a specific CPU.]
+
+.. _acpi-cpufreq:
+
+``intel_pstate`` vs ``acpi-cpufreq``
+====================================
+
+On the majority of systems supported by ``intel_pstate``, the ACPI tables
+provided by the platform firmware contain ``_PSS`` objects returning information
+that can be used for CPU performance scaling (refer to the `ACPI specification`_
+for details on the ``_PSS`` objects and the format of the information returned
+by them).
+
+The information returned by the ACPI ``_PSS`` objects is used by the
+``acpi-cpufreq`` scaling driver.  On systems supported by ``intel_pstate``
+the ``acpi-cpufreq`` driver uses the same hardware CPU performance scaling
+interface, but the set of P-states it can use is limited by the ``_PSS``
+output.
+
+On those systems each ``_PSS`` object returns a list of P-states supported by
+the corresponding CPU which basically is a subset of the P-states range that can
+be used by ``intel_pstate`` on the same system, with one exception: the whole
+`turbo range <turbo_>`_ is represented by one item in it (the topmost one).  By
+convention, the frequency returned by ``_PSS`` for that item is greater by 1 MHz
+than the frequency of the highest non-turbo P-state listed by it, but the
+corresponding P-state representation (following the hardware specification)
+returned for it matches the maximum supported turbo P-state (or is the
+special value 255 meaning essentially "go as high as you can get").
+
+The list of P-states returned by ``_PSS`` is reflected by the table of
+available frequencies supplied by ``acpi-cpufreq`` to the ``CPUFreq`` core and
+scaling governors and the minimum and maximum supported frequencies reported by
+it come from that list as well.  In particular, given the special representation
+of the turbo range described above, this means that the maximum supported
+frequency reported by ``acpi-cpufreq`` is higher by 1 MHz than the frequency
+of the highest supported non-turbo P-state listed by ``_PSS`` which, of course,
+affects decisions made by the scaling governors, except for ``powersave`` and
+``performance``.
+
+For example, if a given governor attempts to select a frequency proportional to
+estimated CPU load and maps the load of 100% to the maximum supported frequency
+(possibly multiplied by a constant), then it will tend to choose P-states below
+the turbo threshold if ``acpi-cpufreq`` is used as the scaling driver, because
+in that case the turbo range corresponds to a small fraction of the frequency
+band it can use (1 MHz vs 1 GHz or more).  In consequence, it will only go to
+the turbo range for the highest loads and the other loads above 50% that might
+benefit from running at turbo frequencies will be given non-turbo P-states
+instead.
+
+One more issue related to that may appear on systems supporting the
+`Configurable TDP feature <turbo_>`_ allowing the platform firmware to set the
+turbo threshold.  Namely, if that is not coordinated with the lists of P-states
+returned by ``_PSS`` properly, there may be more than one item corresponding to
+a turbo P-state in those lists and there may be a problem with avoiding the
+turbo range (if desirable or necessary).  Usually, to avoid using turbo
+P-states overall, ``acpi-cpufreq`` simply avoids using the topmost state listed
+by ``_PSS``, but that is not sufficient when there are other turbo P-states in
+the list returned by it.
+
+Apart from the above, ``acpi-cpufreq`` works like ``intel_pstate`` in the
+`passive mode <Passive Mode_>`_, except that the number of P-states it can set
+is limited to the ones listed by the ACPI ``_PSS`` objects.
+
+
+Kernel Command Line Options for ``intel_pstate``
+================================================
+
+Several kernel command line options can be used to pass early-configuration-time
+parameters to ``intel_pstate`` in order to enforce specific behavior of it.  All
+of them have to be prepended with the ``intel_pstate=`` prefix.
+
+``disable``
+	Do not register ``intel_pstate`` as the scaling driver even if the
+	processor is supported by it.
+
+``passive``
+	Register ``intel_pstate`` in the `passive mode <Passive Mode_>`_ to
+	start with.
+
+	This option implies the ``no_hwp`` one described below.
+
+``force``
+	Register ``intel_pstate`` as the scaling driver instead of
+	``acpi-cpufreq`` even if the latter is preferred on the given system.
+
+	This may prevent some platform features (such as thermal controls and
+	power capping) that rely on the availability of ACPI P-states
+	information from functioning as expected, so it should be used with
+	caution.
+
+	This option does not work with processors that are not supported by
+	``intel_pstate`` and on platforms where the ``pcc-cpufreq`` scaling
+	driver is used instead of ``acpi-cpufreq``.
+
+``no_hwp``
+	Do not enable the `hardware-managed P-states (HWP) feature
+	<Active Mode With HWP_>`_ even if it is supported by the processor.
+
+``hwp_only``
+	Register ``intel_pstate`` as the scaling driver only if the
+	`hardware-managed P-states (HWP) feature <Active Mode With HWP_>`_ is
+	supported by the processor.
+
+``support_acpi_ppc``
+	Take ACPI ``_PPC`` performance limits into account.
+
+	If the preferred power management profile in the FADT (Fixed ACPI
+	Description Table) is set to "Enterprise Server" or "Performance
+	Server", the ACPI ``_PPC`` limits are taken into account by default
+	and this option has no effect.
+
+``per_cpu_perf_limits``
+	Use per-logical-CPU P-State limits (see `Coordination of P-state
+	Limits`_ for details).
+
+
+Diagnostics and Tuning
+======================
+
+Trace Events
+------------
+
+There are two static trace events that can be used for ``intel_pstate``
+diagnostics.  One of them is the ``cpu_frequency`` trace event generally used
+by ``CPUFreq``, and the other one is the ``pstate_sample`` trace event specific
+to ``intel_pstate``.  Both of them are triggered by ``intel_pstate`` only if
+it works in the `active mode <Active Mode_>`_.
+
+The following sequence of shell commands can be used to enable them and see
+their output (if the kernel is generally configured to support event tracing)::
+
+ # cd /sys/kernel/debug/tracing/
+ # echo 1 > events/power/pstate_sample/enable
+ # echo 1 > events/power/cpu_frequency/enable
+ # cat trace
+ gnome-terminal--4510  [001] ..s.  1177.680733: pstate_sample: core_busy=107 scaled=94 from=26 to=26 mperf=1143818 aperf=1230607 tsc=29838618 freq=2474476
+ cat-5235  [002] ..s.  1177.681723: cpu_frequency: state=2900000 cpu_id=2
+
+If ``intel_pstate`` works in the `passive mode <Passive Mode_>`_, the
+``cpu_frequency`` trace event will be triggered either by the ``schedutil``
+scaling governor (for the policies it is attached to), or by the ``CPUFreq``
+core (for the policies with other scaling governors).
+
+``ftrace``
+----------
+
+The ``ftrace`` interface can be used for low-level diagnostics of
+``intel_pstate``.  For example, to check how often the function to set a
+P-state is called, the ``ftrace`` filter can be set to to
+:c:func:`intel_pstate_set_pstate`::
+
+ # cd /sys/kernel/debug/tracing/
+ # cat available_filter_functions | grep -i pstate
+ intel_pstate_set_pstate
+ intel_pstate_cpu_init
+ ...
+ # echo intel_pstate_set_pstate > set_ftrace_filter
+ # echo function > current_tracer
+ # cat trace | head -15
+ # tracer: function
+ #
+ # entries-in-buffer/entries-written: 80/80   #P:4
+ #
+ #                              _-----=> irqs-off
+ #                             / _----=> need-resched
+ #                            | / _---=> hardirq/softirq
+ #                            || / _--=> preempt-depth
+ #                            ||| /     delay
+ #           TASK-PID   CPU#  ||||    TIMESTAMP  FUNCTION
+ #              | |       |   ||||       |         |
+             Xorg-3129  [000] ..s.  2537.644844: intel_pstate_set_pstate <-intel_pstate_timer_func
+  gnome-terminal--4510  [002] ..s.  2537.649844: intel_pstate_set_pstate <-intel_pstate_timer_func
+      gnome-shell-3409  [001] ..s.  2537.650850: intel_pstate_set_pstate <-intel_pstate_timer_func
+           <idle>-0     [000] ..s.  2537.654843: intel_pstate_set_pstate <-intel_pstate_timer_func
+
+Tuning Interface in ``debugfs``
+-------------------------------
+
+The ``powersave`` algorithm provided by ``intel_pstate`` for `the Core line of
+processors in the active mode <powersave_>`_ is based on a `PID controller`_
+whose parameters were chosen to address a number of different use cases at the
+same time.  However, it still is possible to fine-tune it to a specific workload
+and the ``debugfs`` interface under ``/sys/kernel/debug/pstate_snb/`` is
+provided for this purpose.  [Note that the ``pstate_snb`` directory will be
+present only if the specific P-state selection algorithm matching the interface
+in it actually is in use.]
+
+The following files present in that directory can be used to modify the PID
+controller parameters at run time:
+
+| ``deadband``
+| ``d_gain_pct``
+| ``i_gain_pct``
+| ``p_gain_pct``
+| ``sample_rate_ms``
+| ``setpoint``
+
+Note, however, that achieving desirable results this way generally requires
+expert-level understanding of the power vs performance tradeoff, so extra care
+is recommended when attempting to do that.
+
+
+.. _LCEU2015: http://events.linuxfoundation.org/sites/events/files/slides/LinuxConEurope_2015.pdf
+.. _SDM: http://www.intel.com/content/www/us/en/architecture-and-technology/64-ia-32-architectures-software-developer-system-programming-manual-325384.html
+.. _ACPI specification: http://www.uefi.org/sites/default/files/resources/ACPI_6_1.pdf
+.. _PID controller: https://en.wikipedia.org/wiki/PID_controller
diff --git a/Documentation/cpu-freq/intel-pstate.txt b/Documentation/cpu-freq/intel-pstate.txt
deleted file mode 100644
index 3fdcdfd968ba..000000000000
--- a/Documentation/cpu-freq/intel-pstate.txt
+++ /dev/null
@@ -1,281 +0,0 @@
-Intel P-State driver
---------------------
-
-This driver provides an interface to control the P-State selection for the
-SandyBridge+ Intel processors.
-
-The following document explains P-States:
-http://events.linuxfoundation.org/sites/events/files/slides/LinuxConEurope_2015.pdf
-As stated in the document, P-State doesn’t exactly mean a frequency. However, for
-the sake of the relationship with cpufreq, P-State and frequency are used
-interchangeably.
-
-Understanding the cpufreq core governors and policies are important before
-discussing more details about the Intel P-State driver. Based on what callbacks
-a cpufreq driver provides to the cpufreq core, it can support two types of
-drivers:
-- with target_index() callback: In this mode, the drivers using cpufreq core
-simply provide the minimum and maximum frequency limits and an additional
-interface target_index() to set the current frequency. The cpufreq subsystem
-has a number of scaling governors ("performance", "powersave", "ondemand",
-etc.). Depending on which governor is in use, cpufreq core will call for
-transitions to a specific frequency using target_index() callback.
-- setpolicy() callback: In this mode, drivers do not provide target_index()
-callback, so cpufreq core can't request a transition to a specific frequency.
-The driver provides minimum and maximum frequency limits and callbacks to set a
-policy. The policy in cpufreq sysfs is referred to as the "scaling governor".
-The cpufreq core can request the driver to operate in any of the two policies:
-"performance" and "powersave". The driver decides which frequency to use based
-on the above policy selection considering minimum and maximum frequency limits.
-
-The Intel P-State driver falls under the latter category, which implements the
-setpolicy() callback. This driver decides what P-State to use based on the
-requested policy from the cpufreq core. If the processor is capable of
-selecting its next P-State internally, then the driver will offload this
-responsibility to the processor (aka HWP: Hardware P-States). If not, the
-driver implements algorithms to select the next P-State.
-
-Since these policies are implemented in the driver, they are not same as the
-cpufreq scaling governors implementation, even if they have the same name in
-the cpufreq sysfs (scaling_governors). For example the "performance" policy is
-similar to cpufreq’s "performance" governor, but "powersave" is completely
-different than the cpufreq "powersave" governor. The strategy here is similar
-to cpufreq "ondemand", where the requested P-State is related to the system load.
-
-Sysfs Interface
-
-In addition to the frequency-controlling interfaces provided by the cpufreq
-core, the driver provides its own sysfs files to control the P-State selection.
-These files have been added to /sys/devices/system/cpu/intel_pstate/.
-Any changes made to these files are applicable to all CPUs (even in a
-multi-package system, Refer to later section on placing "Per-CPU limits").
-
-      max_perf_pct: Limits the maximum P-State that will be requested by
-      the driver. It states it as a percentage of the available performance. The
-      available (P-State) performance may be reduced by the no_turbo
-      setting described below.
-
-      min_perf_pct: Limits the minimum P-State that will be requested by
-      the driver. It states it as a percentage of the max (non-turbo)
-      performance level.
-
-      no_turbo: Limits the driver to selecting P-State below the turbo
-      frequency range.
-
-      turbo_pct: Displays the percentage of the total performance that
-      is supported by hardware that is in the turbo range. This number
-      is independent of whether turbo has been disabled or not.
-
-      num_pstates: Displays the number of P-States that are supported
-      by hardware. This number is independent of whether turbo has
-      been disabled or not.
-
-For example, if a system has these parameters:
-	Max 1 core turbo ratio: 0x21 (Max 1 core ratio is the maximum P-State)
-	Max non turbo ratio: 0x17
-	Minimum ratio : 0x08 (Here the ratio is called max efficiency ratio)
-
-Sysfs will show :
-	max_perf_pct:100, which corresponds to 1 core ratio
-	min_perf_pct:24, max_efficiency_ratio / max 1 Core ratio
-	no_turbo:0, turbo is not disabled
-	num_pstates:26 = (max 1 Core ratio - Max Efficiency Ratio + 1)
-	turbo_pct:39 = (max 1 core ratio - max non turbo ratio) / num_pstates
-
-Refer to "Intel® 64 and IA-32 Architectures Software Developer’s Manual
-Volume 3: System Programming Guide" to understand ratios.
-
-There is one more sysfs attribute in /sys/devices/system/cpu/intel_pstate/
-that can be used for controlling the operation mode of the driver:
-
-      status: Three settings are possible:
-      "off"     - The driver is not in use at this time.
-      "active"  - The driver works as a P-state governor (default).
-      "passive" - The driver works as a regular cpufreq one and collaborates
-                  with the generic cpufreq governors (it sets P-states as
-                  requested by those governors).
-      The current setting is returned by reads from this attribute.  Writing one
-      of the above strings to it changes the operation mode as indicated by that
-      string, if possible.  If HW-managed P-states (HWP) are enabled, it is not
-      possible to change the driver's operation mode and attempts to write to
-      this attribute will fail.
-
-cpufreq sysfs for Intel P-State
-
-Since this driver registers with cpufreq, cpufreq sysfs is also presented.
-There are some important differences, which need to be considered.
-
-scaling_cur_freq: This displays the real frequency which was used during
-the last sample period instead of what is requested. Some other cpufreq driver,
-like acpi-cpufreq, displays what is requested (Some changes are on the
-way to fix this for acpi-cpufreq driver). The same is true for frequencies
-displayed at /proc/cpuinfo.
-
-scaling_governor: This displays current active policy. Since each CPU has a
-cpufreq sysfs, it is possible to set a scaling governor to each CPU. But this
-is not possible with Intel P-States, as there is one common policy for all
-CPUs. Here, the last requested policy will be applicable to all CPUs. It is
-suggested that one use the cpupower utility to change policy to all CPUs at the
-same time.
-
-scaling_setspeed: This attribute can never be used with Intel P-State.
-
-scaling_max_freq/scaling_min_freq: This interface can be used similarly to
-the max_perf_pct/min_perf_pct of Intel P-State sysfs. However since frequencies
-are converted to nearest possible P-State, this is prone to rounding errors.
-This method is not preferred to limit performance.
-
-affected_cpus: Not used
-related_cpus: Not used
-
-For contemporary Intel processors, the frequency is controlled by the
-processor itself and the P-State exposed to software is related to
-performance levels.  The idea that frequency can be set to a single
-frequency is fictional for Intel Core processors. Even if the scaling
-driver selects a single P-State, the actual frequency the processor
-will run at is selected by the processor itself.
-
-Per-CPU limits
-
-The kernel command line option "intel_pstate=per_cpu_perf_limits" forces
-the intel_pstate driver to use per-CPU performance limits.  When it is set,
-the sysfs control interface described above is subject to limitations.
-- The following controls are not available for both read and write
-	/sys/devices/system/cpu/intel_pstate/max_perf_pct
-	/sys/devices/system/cpu/intel_pstate/min_perf_pct
-- The following controls can be used to set performance limits, as far as the
-architecture of the processor permits:
-	/sys/devices/system/cpu/cpu*/cpufreq/scaling_max_freq
-	/sys/devices/system/cpu/cpu*/cpufreq/scaling_min_freq
-	/sys/devices/system/cpu/cpu*/cpufreq/scaling_governor
-- User can still observe turbo percent and number of P-States from
-	/sys/devices/system/cpu/intel_pstate/turbo_pct
-	/sys/devices/system/cpu/intel_pstate/num_pstates
-- User can read write system wide turbo status
-	/sys/devices/system/cpu/no_turbo
-
-Support of energy performance hints
-It is possible to provide hints to the HWP algorithms in the processor
-to be more performance centric to more energy centric. When the driver
-is using HWP, two additional cpufreq sysfs attributes are presented for
-each logical CPU.
-These attributes are:
-	- energy_performance_available_preferences
-	- energy_performance_preference
-
-To get list of supported hints:
-$ cat energy_performance_available_preferences
-    default performance balance_performance balance_power power
-
-The current preference can be read or changed via cpufreq sysfs
-attribute "energy_performance_preference". Reading from this attribute
-will display current effective setting. User can write any of the valid
-preference string to this attribute. User can always restore to power-on
-default by writing "default".
-
-Since threads can migrate to different CPUs, this is possible that the
-new CPU may have different energy performance preference than the previous
-one. To avoid such issues, either threads can be pinned to specific CPUs
-or set the same energy performance preference value to all CPUs.
-
-Tuning Intel P-State driver
-
-When the performance can be tuned using PID (Proportional Integral
-Derivative) controller, debugfs files are provided for adjusting performance.
-They are presented under:
-/sys/kernel/debug/pstate_snb/
-
-The PID tunable parameters are:
-      deadband
-      d_gain_pct
-      i_gain_pct
-      p_gain_pct
-      sample_rate_ms
-      setpoint
-
-To adjust these parameters, some understanding of driver implementation is
-necessary. There are some tweeks described here, but be very careful. Adjusting
-them requires expert level understanding of power and performance relationship.
-These limits are only useful when the "powersave" policy is active.
-
--To make the system more responsive to load changes, sample_rate_ms can
-be adjusted  (current default is 10ms).
--To make the system use higher performance, even if the load is lower, setpoint
-can be adjusted to a lower number. This will also lead to faster ramp up time
-to reach the maximum P-State.
-If there are no derivative and integral coefficients, The next P-State will be
-equal to:
-	current P-State - ((setpoint - current cpu load) * p_gain_pct)
-
-For example, if the current PID parameters are (Which are defaults for the core
-processors like SandyBridge):
-      deadband = 0
-      d_gain_pct = 0
-      i_gain_pct = 0
-      p_gain_pct = 20
-      sample_rate_ms = 10
-      setpoint = 97
-
-If the current P-State = 0x08 and current load = 100, this will result in the
-next P-State = 0x08 - ((97 - 100) * 0.2) = 8.6 (rounded to 9). Here the P-State
-goes up by only 1. If during next sample interval the current load doesn't
-change and still 100, then P-State goes up by one again. This process will
-continue as long as the load is more than the setpoint until the maximum P-State
-is reached.
-
-For the same load at setpoint = 60, this will result in the next P-State
-= 0x08 - ((60 - 100) * 0.2) = 16
-So by changing the setpoint from 97 to 60, there is an increase of the
-next P-State from 9 to 16. So this will make processor execute at higher
-P-State for the same CPU load. If the load continues to be more than the
-setpoint during next sample intervals, then P-State will go up again till the
-maximum P-State is reached. But the ramp up time to reach the maximum P-State
-will be much faster when the setpoint is 60 compared to 97.
-
-Debugging Intel P-State driver
-
-Event tracing
-To debug P-State transition, the Linux event tracing interface can be used.
-There are two specific events, which can be enabled (Provided the kernel
-configs related to event tracing are enabled).
-
-# cd /sys/kernel/debug/tracing/
-# echo 1 > events/power/pstate_sample/enable
-# echo 1 > events/power/cpu_frequency/enable
-# cat trace
-gnome-terminal--4510  [001] ..s.  1177.680733: pstate_sample: core_busy=107
-	scaled=94 from=26 to=26 mperf=1143818 aperf=1230607 tsc=29838618
-		freq=2474476
-cat-5235  [002] ..s.  1177.681723: cpu_frequency: state=2900000 cpu_id=2
-
-
-Using ftrace
-
-If function level tracing is required, the Linux ftrace interface can be used.
-For example if we want to check how often a function to set a P-State is
-called, we can set ftrace filter to intel_pstate_set_pstate.
-
-# cd /sys/kernel/debug/tracing/
-# cat available_filter_functions | grep -i pstate
-intel_pstate_set_pstate
-intel_pstate_cpu_init
-...
-
-# echo intel_pstate_set_pstate > set_ftrace_filter
-# echo function > current_tracer
-# cat trace | head -15
-# tracer: function
-#
-# entries-in-buffer/entries-written: 80/80   #P:4
-#
-#                              _-----=> irqs-off
-#                             / _----=> need-resched
-#                            | / _---=> hardirq/softirq
-#                            || / _--=> preempt-depth
-#                            ||| /     delay
-#           TASK-PID   CPU#  ||||    TIMESTAMP  FUNCTION
-#              | |       |   ||||       |         |
-            Xorg-3129  [000] ..s.  2537.644844: intel_pstate_set_pstate <-intel_pstate_timer_func
- gnome-terminal--4510  [002] ..s.  2537.649844: intel_pstate_set_pstate <-intel_pstate_timer_func
-     gnome-shell-3409  [001] ..s.  2537.650850: intel_pstate_set_pstate <-intel_pstate_timer_func
-          <idle>-0     [000] ..s.  2537.654843: intel_pstate_set_pstate <-intel_pstate_timer_func
diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
index e9c5a1d9834a..f465647a4dd2 100644
--- a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
+++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt
@@ -22,7 +22,8 @@ Required properties :
 - #clock-cells : must contain 1
 - #reset-cells : must contain 1
 
-For the PRCM CCUs on H3/A64, one more clock is needed:
+For the PRCM CCUs on H3/A64, two more clocks are needed:
+- "pll-periph": the SoC's peripheral PLL from the main CCU
 - "iosc": the SoC's internal frequency oscillator
 
 Example for generic CCU:
@@ -39,8 +40,8 @@ Example for PRCM CCU:
 r_ccu: clock@01f01400 {
 	compatible = "allwinner,sun50i-a64-r-ccu";
 	reg = <0x01f01400 0x100>;
-	clocks = <&osc24M>, <&osc32k>, <&iosc>;
-	clock-names = "hosc", "losc", "iosc";
+	clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>;
+	clock-names = "hosc", "losc", "iosc", "pll-periph";
 	#clock-cells = <1>;
 	#reset-cells = <1>;
 };
diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
index 00ea670b8c4d..06668bca7ffc 100644
--- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
+++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
@@ -78,6 +78,7 @@ graph bindings specified in Documentation/devicetree/bindings/graph.txt.
   remote endpoint phandle should be a reference to a valid mipi_dsi_host device
   node.
 - Video port 1 for the HDMI output
+- Audio port 2 for the HDMI audio input
 
 
 Example
@@ -112,5 +113,12 @@ Example
 					remote-endpoint = <&hdmi_connector_in>;
 				};
 			};
+
+			port@2 {
+				reg = <2>;
+				codec_endpoint: endpoint {
+					remote-endpoint = <&i2s0_cpu_endpoint>;
+				};
+			};
 		};
 	};
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
index f6b3f36d422b..81b68580e199 100644
--- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
@@ -25,7 +25,8 @@ Required properties:
 - clock-names: Shall contain "iahb" and "isfr" as defined in dw_hdmi.txt.
 - ports: See dw_hdmi.txt. The DWC HDMI shall have one port numbered 0
   corresponding to the video input of the controller and one port numbered 1
-  corresponding to its HDMI output. Each port shall have a single endpoint.
+  corresponding to its HDMI output, and one port numbered 2 corresponding to
+  sound input of the controller. Each port shall have a single endpoint.
 
 Optional properties:
 
@@ -59,6 +60,12 @@ Example:
 					remote-endpoint = <&hdmi0_con>;
 				};
 			};
+			port@2 {
+				reg = <2>;
+				rcar_dw_hdmi0_sound_in: endpoint {
+					remote-endpoint = <&hdmi_sound_out>;
+				};
+			};
 		};
 	};
 
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
index 42c3bb2d53e8..01e331a5f3e7 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
@@ -41,9 +41,9 @@ Required properties:
 Optional properties:
 
 In order to use the GPIO lines in PWM mode, some additional optional
-properties are required. Only Armada 370 and XP support these properties.
+properties are required.
 
-- compatible: Must contain "marvell,armada-370-xp-gpio"
+- compatible: Must contain "marvell,armada-370-gpio"
 
 - reg: an additional register set is needed, for the GPIO Blink
   Counter on/off registers.
@@ -71,7 +71,7 @@ Example:
 		};
 
 		gpio1: gpio@18140 {
-			compatible = "marvell,armada-370-xp-gpio";
+			compatible = "marvell,armada-370-gpio";
 			reg = <0x18140 0x40>, <0x181c8 0x08>;
 			reg-names = "gpio", "pwm";
 			ngpios = <17>;
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
index 6db22103e2dd..025cf8c9324a 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
@@ -36,7 +36,7 @@ Optional properties:
                 control gpios
 
  - threshold:   allows setting the "click"-threshold in the range
-                from 20 to 80.
+                from 0 to 80.
 
  - gain:        allows setting the sensitivity in the range from 0 to
                 31. Note that lower values indicate higher
diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
index 05485699d70e..9630ac0e4b56 100644
--- a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
+++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
@@ -16,6 +16,11 @@ Required properties:
 - reg:                  Base address of PMIC on Hi6220 SoC.
 - interrupt-controller: Hi655x has internal IRQs (has own IRQ domain).
 - pmic-gpios:           The GPIO used by PMIC IRQ.
+- #clock-cells:		From common clock binding; shall be set to 0
+
+Optional properties:
+- clock-output-names: From common clock binding to override the
+  default output clock name
 
 Example:
 	pmic: pmic@f8000000 {
@@ -24,4 +29,5 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		#clock-cells = <0>;
 	}
diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt
index bbd083f5600a..1db6e0057a63 100644
--- a/Documentation/devicetree/bindings/mfd/stm32-timers.txt
+++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt
@@ -31,7 +31,7 @@ Example:
 		compatible = "st,stm32-timers";
 		reg = <0x40010000 0x400>;
 		clocks = <&rcc 0 160>;
-		clock-names = "clk_int";
+		clock-names = "int";
 
 		pwm {
 			compatible = "st,stm32-pwm";
diff --git a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt
index e25436861867..9029b45b8a22 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt
+++ b/Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.txt
@@ -18,6 +18,8 @@ Optional properties:
   "ext_clock" (External clock provided to the card).
 - post-power-on-delay-ms : Delay in ms after powering the card and
 	de-asserting the reset-gpios (if any)
+- power-off-delay-us : Delay in us after asserting the reset-gpios (if any)
+	during power off of the card.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt
index d6c6e41648d4..8ec2ca21adeb 100644
--- a/Documentation/devicetree/bindings/net/dsa/b53.txt
+++ b/Documentation/devicetree/bindings/net/dsa/b53.txt
@@ -34,7 +34,7 @@ Required properties:
       "brcm,bcm6328-switch"
       "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
 
-See Documentation/devicetree/bindings/dsa/dsa.txt for a list of additional
+See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required and optional properties.
 
 Examples:
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt
index 7ef9dbb08957..1d4d0f49c9d0 100644
--- a/Documentation/devicetree/bindings/net/dsa/marvell.txt
+++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt
@@ -26,6 +26,10 @@ Optional properties:
 - interrupt-controller	: Indicates the switch is itself an interrupt
 			  controller. This is used for the PHY interrupts.
 #interrupt-cells = <2>	: Controller uses two cells, number and flag
+- eeprom-length		: Set to the length of an EEPROM connected to the
+			  switch. Must be set if the switch can not detect
+			  the presence and/or size of a connected EEPROM,
+			  otherwise optional.
 - mdio			: Container of PHY and devices on the switches MDIO
 			  bus.
 - mdio?		: Container of PHYs and devices on the external MDIO
diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt
index a1e3693cca16..6f55bdd52f8a 100644
--- a/Documentation/devicetree/bindings/net/fsl-fec.txt
+++ b/Documentation/devicetree/bindings/net/fsl-fec.txt
@@ -15,6 +15,10 @@ Optional properties:
 - phy-reset-active-high : If present then the reset sequence using the GPIO
   specified in the "phy-reset-gpios" property is reversed (H=reset state,
   L=operation state).
+- phy-reset-post-delay : Post reset delay in milliseconds. If present then
+  a delay of phy-reset-post-delay milliseconds will be observed after the
+  phy-reset-gpios has been toggled. Can be omitted thus no delay is
+  observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
 - phy-supply : regulator that powers the Ethernet PHY.
 - phy-handle : phandle to the PHY device connected to this device.
 - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt
index 16c3a9501f5d..acfafc8e143c 100644
--- a/Documentation/devicetree/bindings/net/smsc911x.txt
+++ b/Documentation/devicetree/bindings/net/smsc911x.txt
@@ -27,6 +27,7 @@ Optional properties:
   of the device. On many systems this is wired high so the device goes
   out of reset at power-on, but if it is under program control, this
   optional GPIO can wake up in response to it.
+- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies
 
 Examples:
 
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index 71a3c134af1b..f01d154090da 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -247,7 +247,6 @@ bias-bus-hold		- latch weakly
 bias-pull-up		- pull up the pin
 bias-pull-down		- pull down the pin
 bias-pull-pin-default	- use pin-default pull state
-bi-directional		- pin supports simultaneous input/output operations
 drive-push-pull		- drive actively high and low
 drive-open-drain	- drive with open drain
 drive-open-source	- drive with open source
@@ -260,7 +259,6 @@ input-debounce		- debounce mode with debound time X
 power-source		- select between different power supplies
 low-power-enable	- enable low power mode
 low-power-disable	- disable low power mode
-output-enable		- enable output on pin regardless of output value
 output-low		- set the pin to output mode with low level
 output-high		- set the pin to output mode with high level
 slew-rate		- set the slew rate
diff --git a/Documentation/devicetree/bindings/sound/audio-graph-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
new file mode 100644
index 000000000000..6e6720aa33f1
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/audio-graph-card.txt
@@ -0,0 +1,129 @@
+Audio Graph Card:
+
+Audio Graph Card specifies audio DAI connections of SoC <-> codec.
+It is based on common bindings for device graphs.
+see ${LINUX}/Documentation/devicetree/bindings/graph.txt
+
+Basically, Audio Graph Card property is same as Simple Card.
+see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt
+
+Below are same as Simple-Card.
+
+- label
+- widgets
+- routing
+- dai-format
+- frame-master
+- bitclock-master
+- bitclock-inversion
+- frame-inversion
+- dai-tdm-slot-num
+- dai-tdm-slot-width
+- clocks / system-clock-frequency
+
+Required properties:
+
+- compatible				: "audio-graph-card";
+- dais					: list of CPU DAI port{s}
+
+Optional properties:
+- pa-gpios: GPIO used to control external amplifier.
+
+Example: Single DAI case
+
+	sound_card {
+		compatible = "audio-graph-card";
+
+		dais = <&cpu_port>;
+	};
+
+	dai-controller {
+		...
+		cpu_port: port {
+			cpu_endpoint: endpoint {
+				remote-endpoint = <&codec_endpoint>;
+
+				dai-format = "left_j";
+				...
+			};
+		};
+	};
+
+	audio-codec {
+		...
+		port {
+			codec_endpoint: endpoint {
+				remote-endpoint = <&cpu_endpoint>;
+			};
+		};
+	};
+
+Example: Multi DAI case
+
+	sound-card {
+		compatible = "audio-graph-card";
+
+		label = "sound-card";
+
+		dais = <&cpu_port0
+			&cpu_port1
+			&cpu_port2>;
+	};
+
+	audio-codec@0 {
+		...
+		port {
+			codec0_endpoint: endpoint {
+				remote-endpoint = <&cpu_endpoint0>;
+			};
+		};
+	};
+
+	audio-codec@1 {
+		...
+		port {
+			codec1_endpoint: endpoint {
+				remote-endpoint = <&cpu_endpoint1>;
+			};
+		};
+	};
+
+	audio-codec@2 {
+		...
+		port {
+			codec2_endpoint: endpoint {
+				remote-endpoint = <&cpu_endpoint2>;
+			};
+		};
+	};
+
+	dai-controller {
+		...
+		ports {
+			cpu_port0: port@0 {
+				cpu_endpoint0: endpoint {
+					remote-endpoint = <&codec0_endpoint>;
+
+					dai-format = "left_j";
+					...
+				};
+			};
+			cpu_port1: port@1 {
+				cpu_endpoint1: endpoint {
+					remote-endpoint = <&codec1_endpoint>;
+
+					dai-format = "i2s";
+					...
+				};
+			};
+			cpu_port2: port@2 {
+				cpu_endpoint2: endpoint {
+					remote-endpoint = <&codec2_endpoint>;
+
+					dai-format = "i2s";
+					...
+				};
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt
new file mode 100644
index 000000000000..8b8afe9fcb31
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/audio-graph-scu-card.txt
@@ -0,0 +1,122 @@
+Audio-Graph-SCU-Card:
+
+Audio-Graph-SCU-Card is "Audio-Graph-Card" + "ALSA DPCM".
+
+It is based on common bindings for device graphs.
+see ${LINUX}/Documentation/devicetree/bindings/graph.txt
+
+Basically, Audio-Graph-SCU-Card property is same as
+Simple-Card / Simple-SCU-Card / Audio-Graph-Card.
+see ${LINUX}/Documentation/devicetree/bindings/sound/simple-card.txt
+    ${LINUX}/Documentation/devicetree/bindings/sound/simple-scu-card.txt
+    ${LINUX}/Documentation/devicetree/bindings/sound/audio-graph-card.txt
+
+Below are same as Simple-Card / Audio-Graph-Card.
+
+- label
+- dai-format
+- frame-master
+- bitclock-master
+- bitclock-inversion
+- frame-inversion
+- dai-tdm-slot-num
+- dai-tdm-slot-width
+- clocks / system-clock-frequency
+
+Below are same as Simple-SCU-Card.
+
+- convert-rate
+- convert-channels
+- prefix
+- routing
+
+Required properties:
+
+- compatible				: "audio-graph-scu-card";
+- dais					: list of CPU DAI port{s}
+
+Example 1. Sampling Rate Conversion
+
+	sound_card {
+		compatible = "audio-graph-scu-card";
+
+		label = "sound-card";
+		prefix = "codec";
+		routing = "codec Playback", "DAI0 Playback",
+			"codec Playback", "DAI1 Playback";
+		convert-rate = <48000>;
+
+		dais = <&cpu_port>;
+	};
+
+	audio-codec {
+		...
+
+		port {
+			codec_endpoint: endpoint {
+				remote-endpoint = <&cpu_endpoint>;
+			};
+		};
+	};
+
+	dai-controller {
+		...
+		cpu_port: port {
+			cpu_endpoint: endpoint {
+				remote-endpoint = <&codec_endpoint>;
+
+				dai-format = "left_j";
+				...
+			};
+		};
+	};
+
+Example 2. 2 CPU 1 Codec (Mixing)
+
+	sound_card {
+		compatible = "audio-graph-scu-card";
+
+		label = "sound-card";
+		prefix = "codec";
+		routing = "codec Playback", "DAI0 Playback",
+			"codec Playback", "DAI1 Playback";
+		convert-rate = <48000>;
+
+		dais = <&cpu_port0
+			&cpu_port1>;
+	};
+
+	audio-codec {
+		...
+
+		port {
+			codec_endpoint0: endpoint {
+				remote-endpoint = <&cpu_endpoint0>;
+			};
+			codec_endpoint1: endpoint {
+				remote-endpoint = <&cpu_endpoint1>;
+			};
+		};
+	};
+
+	dai-controller {
+		...
+		ports {
+			cpu_port0: port {
+				cpu_endpoint0: endpoint {
+					remote-endpoint = <&codec_endpoint0>;
+
+					dai-format = "left_j";
+					...
+				};
+			};
+			cpu_port1: port {
+				cpu_endpoint1: endpoint {
+					remote-endpoint = <&codec_endpoint1>;
+
+					dai-format = "left_j";
+					...
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/sound/cs35l35.txt b/Documentation/devicetree/bindings/sound/cs35l35.txt
index 016b768bc722..77ee75c39233 100644
--- a/Documentation/devicetree/bindings/sound/cs35l35.txt
+++ b/Documentation/devicetree/bindings/sound/cs35l35.txt
@@ -16,6 +16,9 @@ Required properties:
     (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
     for further information relating to interrupt properties)
 
+ - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
+    in nH and they can be values of 1000nH, 1200nH, 1500nH, and 2200nH.
+
 Optional properties:
   - reset-gpios : gpio used to reset the amplifier
 
diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt
index d3374231c871..2f5e973285a6 100644
--- a/Documentation/devicetree/bindings/sound/nau8825.txt
+++ b/Documentation/devicetree/bindings/sound/nau8825.txt
@@ -69,6 +69,8 @@ Optional properties:
   - nuvoton,jack-insert-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
   - nuvoton,jack-eject-debounce: number from 0 to 7 that sets debounce time to 2^(n+2) ms
 
+  - nuvoton,crosstalk-bypass: make crosstalk function bypass if set.
+
   - clocks: list of phandle and clock specifier pairs according to common clock bindings for the
       clocks described in clock-names
   - clock-names: should include "mclk" for the MCLK master clock
@@ -96,6 +98,7 @@ Example:
       nuvoton,short-key-debounce = <2>;
       nuvoton,jack-insert-debounce = <7>;
       nuvoton,jack-eject-debounce = <7>;
+      nuvoton,crosstalk-bypass;
 
       clock-names = "mclk";
       clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>;
diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
index 15a7316e4c91..7246bb268bf9 100644
--- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
+++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt
@@ -83,11 +83,11 @@ SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes
 **     Asynchronous mode
 ------------------
 
-You need to use "renesas,rsrc-card" sound card for it.
+You need to use "simple-scu-audio-card" sound card for it.
 example)
 
 	sound {
-		compatible = "renesas,rsrc-card";
+		compatible = "simple-scu-audio-card";
 		...
 		/*
 		 * SRC Asynchronous mode setting
@@ -97,12 +97,12 @@ example)
 		 * Inputed 48kHz data will be converted to
 		 * system specified Hz
 		 */
-		convert-rate = <48000>;
+		simple-audio-card,convert-rate = <48000>;
 		...
-		cpu {
+		simple-audio-card,cpu {
 			sound-dai = <&rcar_sound>;
 		};
-		codec {
+		simple-audio-card,codec {
 			...
 		};
 	};
@@ -141,23 +141,23 @@ For more detail information, see below
 	${LINUX}/sound/soc/sh/rcar/ctu.c
 	 - comment of header
 
-You need to use "renesas,rsrc-card" sound card for it.
+You need to use "simple-scu-audio-card" sound card for it.
 example)
 
 	sound {
-		compatible = "renesas,rsrc-card";
+		compatible = "simple-scu-audio-card";
 		...
 		/*
 		 * CTU setting
 		 * All input data will be converted to 2ch
 		 * as output data
 		 */
-		convert-channels = <2>;
+		simple-audio-card,convert-channels = <2>;
 		...
-		cpu {
+		simple-audio-card,cpu {
 			sound-dai = <&rcar_sound>;
 		};
-		codec {
+		simple-audio-card,codec {
 			...
 		};
 	};
@@ -190,22 +190,22 @@ and these sounds will be merged by MIX.
 	aplay -D plughw:0,0 xxxx.wav &
 	aplay -D plughw:0,1 yyyy.wav
 
-You need to use "renesas,rsrc-card" sound card for it.
+You need to use "simple-scu-audio-card" sound card for it.
 Ex)
 	[MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0]
 	                            |
 	[MEM] -> [SRC2] -> [CTU03] -+
 
 	sound {
-		compatible = "renesas,rsrc-card";
+		compatible = "simple-scu-audio-card";
 		...
-		cpu@0 {
+		simple-audio-card,cpu@0 {
 			sound-dai = <&rcar_sound 0>;
 		};
-		cpu@1 {
+		simple-audio-card,cpu@1 {
 			sound-dai = <&rcar_sound 1>;
 		};
-		codec {
+		simple-audio-card,codec {
 			...
 		};
 	};
@@ -368,6 +368,10 @@ Required properties:
 				  see below for detail.
 - #sound-dai-cells		: it must be 0 if your system is using single DAI
 				  it must be 1 if your system is using multi  DAI
+- clocks			: References to SSI/SRC/MIX/CTU/DVC/AUDIO_CLK clocks.
+- clock-names			: List of necessary clock names.
+				  "ssi-all", "ssi.X", "src.X", "mix.X", "ctu.X",
+				  "dvc.X", "clk_a", "clk_b", "clk_c", "clk_i"
 
 Optional properties:
 - #clock-cells			: it must be 0 if your system has audio_clkout
@@ -375,6 +379,9 @@ Optional properties:
 - clock-frequency		: for all audio_clkout0/1/2/3
 - clkout-lr-asynchronous	: boolean property. it indicates that audio_clkoutn
 				  is asynchronizes with lr-clock.
+- resets			: References to SSI resets.
+- reset-names			: List of valid reset names.
+				  "ssi-all", "ssi.X"
 
 SSI subnode properties:
 - interrupts			: Should contain SSI interrupt for PIO transfer
diff --git a/Documentation/devicetree/bindings/sound/rockchip,pdm.txt b/Documentation/devicetree/bindings/sound/rockchip,pdm.txt
new file mode 100644
index 000000000000..921729de7346
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/rockchip,pdm.txt
@@ -0,0 +1,39 @@
+* Rockchip PDM controller
+
+Required properties:
+
+- compatible: "rockchip,pdm"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- dmas: DMA specifiers for rx dma. See the DMA client binding,
+	Documentation/devicetree/bindings/dma/dma.txt
+- dma-names: should include "rx".
+- clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names.
+- clock-names: should contain following:
+   - "pdm_hclk": clock for PDM BUS
+   - "pdm_clk" : clock for PDM controller
+- pinctrl-names: Must contain a "default" entry.
+- pinctrl-N: One property must exist for each entry in
+	     pinctrl-names. See ../pinctrl/pinctrl-bindings.txt
+	     for details of the property values.
+
+Example for rk3328 PDM controller:
+
+pdm: pdm@ff040000 {
+	compatible = "rockchip,pdm";
+	reg = <0x0 0xff040000 0x0 0x1000>;
+	clocks = <&clk_pdm>, <&clk_gates28 0>;
+	clock-names = "pdm_clk", "pdm_hclk";
+	dmas = <&pdma 16>;
+	#dma-cells = <1>;
+	dma-names = "rx";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pdmm0_clk
+		     &pdmm0_fsync
+		     &pdmm0_sdi0
+		     &pdmm0_sdi1
+		     &pdmm0_sdi2
+		     &pdmm0_sdi3>;
+	pinctrl-1 = <&pdmm0_sleep>;
+	status = "disabled";
+};
diff --git a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt
index 11046429a118..4706b96d450b 100644
--- a/Documentation/devicetree/bindings/sound/rockchip-spdif.txt
+++ b/Documentation/devicetree/bindings/sound/rockchip-spdif.txt
@@ -9,7 +9,9 @@ Required properties:
 - compatible: should be one of the following:
    - "rockchip,rk3066-spdif"
    - "rockchip,rk3188-spdif"
+   - "rockchip,rk3228-spdif"
    - "rockchip,rk3288-spdif"
+   - "rockchip,rk3328-spdif"
    - "rockchip,rk3366-spdif"
    - "rockchip,rk3368-spdif"
    - "rockchip,rk3399-spdif"
diff --git a/Documentation/devicetree/bindings/sound/samsung,odroid.txt b/Documentation/devicetree/bindings/sound/samsung,odroid.txt
index c1ac70cb0afb..c30934dd975b 100644
--- a/Documentation/devicetree/bindings/sound/samsung,odroid.txt
+++ b/Documentation/devicetree/bindings/sound/samsung,odroid.txt
@@ -5,11 +5,6 @@ Required properties:
  - compatible - "samsung,odroidxu3-audio" - for Odroid XU3 board,
 		"samsung,odroidxu4-audio" - for Odroid XU4 board
  - model - the user-visible name of this sound complex
- - 'cpu' subnode with a 'sound-dai' property containing the phandle of the I2S
-    controller
- - 'codec' subnode with a 'sound-dai' property containing list of phandles
-    to the CODEC nodes, first entry must be corresponding to the MAX98090
-    CODEC and the second entry must be the phandle of the HDMI IP block node
  - clocks - should contain entries matching clock names in the clock-names
     property
  - clock-names - should contain following entries:
@@ -32,12 +27,18 @@ Required properties:
    For Odroid XU4:
      no entries
 
+Required sub-nodes:
+
+ - 'cpu' subnode with a 'sound-dai' property containing the phandle of the I2S
+    controller
+ - 'codec' subnode with a 'sound-dai' property containing list of phandles
+    to the CODEC nodes, first entry must be corresponding to the MAX98090
+    CODEC and the second entry must be the phandle of the HDMI IP block node
+
 Example:
 
 sound {
 	compatible = "samsung,odroidxu3-audio";
-	samsung,cpu-dai = <&i2s0>;
-	samsung,codec-dai = <&max98090>;
 	model = "Odroid-XU3";
 	samsung,audio-routing =
 		"Headphone Jack", "HPL",
diff --git a/Documentation/devicetree/bindings/sound/simple-scu-card.txt b/Documentation/devicetree/bindings/sound/simple-scu-card.txt
index d6fe47ed09af..327d229a51b2 100644
--- a/Documentation/devicetree/bindings/sound/simple-scu-card.txt
+++ b/Documentation/devicetree/bindings/sound/simple-scu-card.txt
@@ -1,35 +1,29 @@
-ASoC simple SCU Sound Card
+ASoC Simple SCU Sound Card
 
-Simple-Card specifies audio DAI connections of SoC <-> codec.
+Simple SCU Sound Card is "Simple Sound Card" + "ALSA DPCM".
+For example, you can use this driver if you want to exchange sampling rate convert,
+Mixing, etc...
 
 Required properties:
 
 - compatible				: "simple-scu-audio-card"
 					  "renesas,rsrc-card"
-
 Optional properties:
 
-- simple-audio-card,name		: User specified audio sound card name, one string
-					  property.
-- simple-audio-card,cpu			: CPU   sub-node
-- simple-audio-card,codec		: CODEC sub-node
+- simple-audio-card,name		: see simple-audio-card.txt
+- simple-audio-card,cpu			: see simple-audio-card.txt
+- simple-audio-card,codec		: see simple-audio-card.txt
 
 Optional subnode properties:
 
-- simple-audio-card,format		: CPU/CODEC common audio format.
-					  "i2s", "right_j", "left_j" , "dsp_a"
-					  "dsp_b", "ac97", "pdm", "msb", "lsb"
-- simple-audio-card,frame-master	: Indicates dai-link frame master.
-					  phandle to a cpu or codec subnode.
-- simple-audio-card,bitclock-master	: Indicates dai-link bit clock master.
-					  phandle to a cpu or codec subnode.
-- simple-audio-card,bitclock-inversion	: bool property. Add this if the
-					  dai-link uses bit clock inversion.
-- simple-audio-card,frame-inversion	: bool property. Add this if the
-					  dai-link uses frame clock inversion.
+- simple-audio-card,format		: see simple-audio-card.txt
+- simple-audio-card,frame-master	: see simple-audio-card.txt
+- simple-audio-card,bitclock-master	: see simple-audio-card.txt
+- simple-audio-card,bitclock-inversion	: see simple-audio-card.txt
+- simple-audio-card,frame-inversion	: see simple-audio-card.txt
 - simple-audio-card,convert-rate	: platform specified sampling rate convert
 - simple-audio-card,convert-channels	: platform specified converted channel size (2 - 8 ch)
-- simple-audio-card,prefix		: see audio-routing
+- simple-audio-card,prefix		: see routing
 - simple-audio-card,routing		: A list of the connections between audio components.
 					  Each entry is a pair of strings, the first being the connection's sink,
 					  the second being the connection's source. Valid names for sources.
@@ -38,32 +32,23 @@ Optional subnode properties:
 
 Required CPU/CODEC subnodes properties:
 
-- sound-dai				: phandle and port of CPU/CODEC
+- sound-dai				: see simple-audio-card.txt
 
 Optional CPU/CODEC subnodes properties:
 
-- clocks / system-clock-frequency	: specify subnode's clock if needed.
-					  it can be specified via "clocks" if system has
-					  clock node (= common clock), or "system-clock-frequency"
-					  (if system doens't support common clock)
-					  If a clock is specified, it is
-					  enabled with clk_prepare_enable()
-					  in dai startup() and disabled with
-					  clk_disable_unprepare() in dai
-					  shutdown().
+- clocks / system-clock-frequency	: see simple-audio-card.txt
 
-Example 1. Sampling Rate Covert
+Example 1. Sampling Rate Conversion
 
 sound {
 	compatible = "simple-scu-audio-card";
 
 	simple-audio-card,name = "rsnd-ak4643";
 	simple-audio-card,format = "left_j";
-	simple-audio-card,format = "left_j";
 	simple-audio-card,bitclock-master = <&sndcodec>;
 	simple-audio-card,frame-master = <&sndcodec>;
 
-	simple-audio-card,convert-rate = <48000>; /* see audio_clk_a */
+	simple-audio-card,convert-rate = <48000>;
 
 	simple-audio-card,prefix = "ak4642";
 	simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback",
@@ -79,20 +64,18 @@ sound {
 	};
 };
 
-Example 2. 2 CPU 1 Codec
+Example 2. 2 CPU 1 Codec (Mixing)
 
 sound {
-	compatible = "renesas,rsrc-card";
-
-	card-name = "rsnd-ak4643";
-	format = "left_j";
-	bitclock-master = <&dpcmcpu>;
-	frame-master = <&dpcmcpu>;
+	compatible = "simple-scu-audio-card";
 
-	convert-rate = <48000>;  /* see audio_clk_a */
+	simple-audio-card,name = "rsnd-ak4643";
+	simple-audio-card,format = "left_j";
+	simple-audio-card,bitclock-master = <&dpcmcpu>;
+	simple-audio-card,frame-master = <&dpcmcpu>;
 
-	audio-prefix = "ak4642";
-	audio-routing = "ak4642 Playback", "DAI0 Playback",
+	simple-audio-card,prefix = "ak4642";
+	simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback",
 			"ak4642 Playback", "DAI1 Playback";
 
 	dpcmcpu: cpu@0 {
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt b/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt
new file mode 100644
index 000000000000..4bda52042402
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,stm32-i2s.txt
@@ -0,0 +1,62 @@
+STMicroelectronics STM32 SPI/I2S Controller
+
+The SPI/I2S block supports I2S/PCM protocols when configured on I2S mode.
+Only some SPI instances support I2S.
+
+Required properties:
+  - compatible: Must be "st,stm32h7-i2s"
+  - reg: Offset and length of the device's register set.
+  - interrupts: Must contain the interrupt line id.
+  - clocks: Must contain phandle and clock specifier pairs for each entry
+	in clock-names.
+  - clock-names: Must contain "i2sclk", "pclk", "x8k" and "x11k".
+	"i2sclk": clock which feeds the internal clock generator
+	"pclk": clock which feeds the peripheral bus interface
+	"x8k": I2S parent clock for sampling rates multiple of 8kHz.
+	"x11k": I2S parent clock for sampling rates multiple of 11.025kHz.
+  - dmas: DMA specifiers for tx and rx dma.
+    See Documentation/devicetree/bindings/dma/stm32-dma.txt.
+  - dma-names: Identifier for each DMA request line. Must be "tx" and "rx".
+  - pinctrl-names: should contain only value "default"
+  - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt
+
+Optional properties:
+  - resets: Reference to a reset controller asserting the reset controller
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+graph.txt.
+
+Example:
+sound_card {
+	compatible = "audio-graph-card";
+	dais = <&i2s2_port>;
+};
+
+i2s2: audio-controller@40003800 {
+	compatible = "st,stm32h7-i2s";
+	reg = <0x40003800 0x400>;
+	interrupts = <36>;
+	clocks = <&rcc PCLK1>, <&rcc SPI2_CK>, <&rcc PLL1_Q>, <&rcc PLL2_P>;
+	clock-names = "pclk", "i2sclk",  "x8k", "x11k";
+	dmas = <&dmamux2 2 39 0x400 0x1>,
+           <&dmamux2 3 40 0x400 0x1>;
+	dma-names = "rx", "tx";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2s2>;
+
+	i2s2_port: port@0 {
+		cpu_endpoint: endpoint {
+			remote-endpoint = <&codec_endpoint>;
+			format = "i2s";
+		};
+	};
+};
+
+audio-codec {
+	codec_port: port@0 {
+		codec_endpoint: endpoint {
+			remote-endpoint = <&cpu_endpoint>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt
index c59a3d779e06..f1c5ae59e7c9 100644
--- a/Documentation/devicetree/bindings/sound/st,stm32-sai.txt
+++ b/Documentation/devicetree/bindings/sound/st,stm32-sai.txt
@@ -6,7 +6,7 @@ The SAI contains two independent audio sub-blocks. Each sub-block has
 its own clock generator and I/O lines controller.
 
 Required properties:
-  - compatible: Should be "st,stm32f4-sai"
+  - compatible: Should be "st,stm32f4-sai" or "st,stm32h7-sai"
   - reg: Base address and size of SAI common register set.
   - clocks: Must contain phandle and clock specifier pairs for each entry
 	in clock-names.
@@ -36,6 +36,10 @@ SAI subnodes required properties:
   - pinctrl-names: should contain only value "default"
   - pinctrl-0: see Documentation/devicetree/bindings/pinctrl/pinctrl-stm32.txt
 
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+graph.txt.
+
 Example:
 sound_card {
 	compatible = "audio-graph-card";
@@ -43,38 +47,29 @@ sound_card {
 };
 
 sai1: sai1@40015800 {
-	compatible = "st,stm32f4-sai";
+	compatible = "st,stm32h7-sai";
 	#address-cells = <1>;
 	#size-cells = <1>;
-	ranges;
+	ranges = <0 0x40015800 0x400>;
 	reg = <0x40015800 0x4>;
-	clocks = <&rcc 1 CLK_SAIQ_PDIV>, <&rcc 1 CLK_I2SQ_PDIV>;
+	clocks = <&rcc PLL1_Q>, <&rcc PLL2_P>;
 	clock-names = "x8k", "x11k";
 	interrupts = <87>;
 
-	sai1b: audio-controller@40015824 {
-		#sound-dai-cells = <0>;
-		compatible = "st,stm32-sai-sub-b";
-		reg = <0x40015824 0x1C>;
-		clocks = <&rcc 1 CLK_SAI2>;
+	sai1a: audio-controller@40015804 {
+		compatible = "st,stm32-sai-sub-a";
+		reg = <0x4 0x1C>;
+		clocks = <&rcc SAI1_CK>;
 		clock-names = "sai_ck";
-		dmas = <&dma2 5 0 0x400 0x0>;
+		dmas = <&dmamux1 1 87 0x400 0x0>;
 		dma-names = "tx";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_sai1b>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
+		pinctrl-0 = <&pinctrl_sai1a>;
 
-			sai1b_port: port@0 {
-				reg = <0>;
-				cpu_endpoint: endpoint {
-					remote-endpoint = <&codec_endpoint>;
-					audio-graph-card,format = "i2s";
-					audio-graph-card,bitclock-master = <&codec_endpoint>;
-					audio-graph-card,frame-master = <&codec_endpoint>;
-				};
+		sai1b_port: port {
+			cpu_endpoint: endpoint {
+				remote-endpoint = <&codec_endpoint>;
+				format = "i2s";
 			};
 		};
 	};
diff --git a/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
new file mode 100644
index 000000000000..33826f2459fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,stm32-spdifrx.txt
@@ -0,0 +1,56 @@
+STMicroelectronics STM32 S/PDIF receiver (SPDIFRX).
+
+The SPDIFRX peripheral, is designed to receive an S/PDIF flow compliant with
+IEC-60958 and IEC-61937.
+
+Required properties:
+  - compatible: should be "st,stm32h7-spdifrx"
+  - reg: cpu DAI IP base address and size
+  - clocks: must contain an entry for kclk (used as S/PDIF signal reference)
+  - clock-names: must contain "kclk"
+  - interrupts: cpu DAI interrupt line
+  - dmas: DMA specifiers for audio data DMA and iec control flow DMA
+    See STM32 DMA bindings, Documentation/devicetree/bindings/dma/stm32-dma.txt
+  - dma-names: two dmas have to be defined, "rx" and "rx-ctrl"
+
+Optional properties:
+  - resets: Reference to a reset controller asserting the SPDIFRX
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+graph.txt.
+
+Example:
+spdifrx: spdifrx@40004000 {
+	compatible = "st,stm32h7-spdifrx";
+	reg = <0x40004000 0x400>;
+	clocks = <&rcc SPDIFRX_CK>;
+	clock-names = "kclk";
+	interrupts = <97>;
+	dmas = <&dmamux1 2 93 0x400 0x0>,
+	       <&dmamux1 3 94 0x400 0x0>;
+	dma-names = "rx", "rx-ctrl";
+	pinctrl-0 = <&spdifrx_pins>;
+	pinctrl-names = "default";
+
+	spdifrx_port: port {
+		cpu_endpoint: endpoint {
+			remote-endpoint = <&codec_endpoint>;
+		};
+	};
+};
+
+spdif_in: spdif-in {
+	compatible = "linux,spdif-dir";
+
+	codec_port: port {
+		codec_endpoint: endpoint {
+			remote-endpoint = <&cpu_endpoint>;
+		};
+	};
+};
+
+soundcard {
+	compatible = "audio-graph-card";
+	dais = <&spdifrx_port>;
+};
diff --git a/Documentation/devicetree/bindings/sound/sun4i-codec.txt b/Documentation/devicetree/bindings/sound/sun4i-codec.txt
index 3863531d1e6d..2d4e10deb6f4 100644
--- a/Documentation/devicetree/bindings/sound/sun4i-codec.txt
+++ b/Documentation/devicetree/bindings/sound/sun4i-codec.txt
@@ -7,6 +7,7 @@ Required properties:
 		- "allwinner,sun7i-a20-codec"
 		- "allwinner,sun8i-a23-codec"
 		- "allwinner,sun8i-h3-codec"
+		- "allwinner,sun8i-v3s-codec"
 - reg: must contain the registers location and length
 - interrupts: must contain the codec interrupt
 - dmas: DMA channels for tx and rx dma. See the DMA client binding,
@@ -25,6 +26,7 @@ Required properties for the following compatibles:
 		- "allwinner,sun6i-a31-codec"
 		- "allwinner,sun8i-a23-codec"
 		- "allwinner,sun8i-h3-codec"
+		- "allwinner,sun8i-v3s-codec"
 - resets: phandle to the reset control for this device
 - allwinner,audio-routing: A list of the connections between audio components.
 			   Each entry is a pair of strings, the first being the
@@ -34,15 +36,15 @@ Required properties for the following compatibles:
 			   Audio pins on the SoC:
 			   "HP"
 			   "HPCOM"
-			   "LINEIN"
-			   "LINEOUT"	(not on sun8i-a23)
+			   "LINEIN"	(not on sun8i-v3s)
+			   "LINEOUT"	(not on sun8i-a23 or sun8i-v3s)
 			   "MIC1"
-			   "MIC2"
+			   "MIC2"	(not on sun8i-v3s)
 			   "MIC3"	(sun6i-a31 only)
 
 			   Microphone biases from the SoC:
 			   "HBIAS"
-			   "MBIAS"
+			   "MBIAS"	(not on sun8i-v3s)
 
 			   Board connectors:
 			   "Headphone"
@@ -55,6 +57,7 @@ Required properties for the following compatibles:
 Required properties for the following compatibles:
 		- "allwinner,sun8i-a23-codec"
 		- "allwinner,sun8i-h3-codec"
+		- "allwinner,sun8i-v3s-codec"
 - allwinner,codec-analog-controls: A phandle to the codec analog controls
 				   block in the PRCM.
 
diff --git a/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt
index 779b735781ba..1b6e7c4e50ab 100644
--- a/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt
+++ b/Documentation/devicetree/bindings/sound/sun8i-codec-analog.txt
@@ -4,6 +4,7 @@ Required properties:
 - compatible: must be one of the following compatibles:
 		- "allwinner,sun8i-a23-codec-analog"
 		- "allwinner,sun8i-h3-codec-analog"
+		- "allwinner,sun8i-v3s-codec-analog"
 
 Required properties if not a sub-node of the PRCM node:
 - reg: must contain the registers location and length
diff --git a/Documentation/devicetree/bindings/sound/zte,zx-aud96p22.txt b/Documentation/devicetree/bindings/sound/zte,zx-aud96p22.txt
new file mode 100644
index 000000000000..41bb1040eb71
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/zte,zx-aud96p22.txt
@@ -0,0 +1,24 @@
+ZTE ZX AUD96P22 Audio Codec
+
+Required properties:
+ - compatible: Must be "zte,zx-aud96p22"
+ - #sound-dai-cells: Should be 0
+ - reg: I2C bus slave address of AUD96P22
+
+Example:
+
+	i2c0: i2c@1486000 {
+		compatible = "zte,zx296718-i2c";
+		reg = <0x01486000 0x1000>;
+		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&audiocrm AUDIO_I2C0_WCLK>;
+		clock-frequency = <1600000>;
+
+		aud96p22: codec@22 {
+			compatible = "zte,zx-aud96p22";
+			#sound-dai-cells = <0>;
+			reg = <0x22>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index 00bea038639e..fcf199b64d3d 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -10,6 +10,7 @@ Required properties:
   - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
   - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
   - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs;
+  - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs;
   - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs;
   - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs;
   - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs;
diff --git a/Documentation/input/devices/edt-ft5x06.rst b/Documentation/input/devices/edt-ft5x06.rst
index 2032f0b7a8fa..1ccc94b192b7 100644
--- a/Documentation/input/devices/edt-ft5x06.rst
+++ b/Documentation/input/devices/edt-ft5x06.rst
@@ -15,7 +15,7 @@ It has been tested with the following devices:
 The driver allows configuration of the touch screen via a set of sysfs files:
 
 /sys/class/input/eventX/device/device/threshold:
-    allows setting the "click"-threshold in the range from 20 to 80.
+    allows setting the "click"-threshold in the range from 0 to 80.
 
 /sys/class/input/eventX/device/device/gain:
     allows setting the sensitivity in the range from 0 to 31. Note that
diff --git a/Documentation/networking/dpaa.txt b/Documentation/networking/dpaa.txt
new file mode 100644
index 000000000000..76e016d4d344
--- /dev/null
+++ b/Documentation/networking/dpaa.txt
@@ -0,0 +1,194 @@
+The QorIQ DPAA Ethernet Driver
+==============================
+
+Authors:
+Madalin Bucur <madalin.bucur@nxp.com>
+Camelia Groza <camelia.groza@nxp.com>
+
+Contents
+========
+
+	- DPAA Ethernet Overview
+	- DPAA Ethernet Supported SoCs
+	- Configuring DPAA Ethernet in your kernel
+	- DPAA Ethernet Frame Processing
+	- DPAA Ethernet Features
+	- Debugging
+
+DPAA Ethernet Overview
+======================
+
+DPAA stands for Data Path Acceleration Architecture and it is a
+set of networking acceleration IPs that are available on several
+generations of SoCs, both on PowerPC and ARM64.
+
+The Freescale DPAA architecture consists of a series of hardware blocks
+that support Ethernet connectivity. The Ethernet driver depends upon the
+following drivers in the Linux kernel:
+
+ - Peripheral Access Memory Unit (PAMU) (* needed only for PPC platforms)
+    drivers/iommu/fsl_*
+ - Frame Manager (FMan)
+    drivers/net/ethernet/freescale/fman
+ - Queue Manager (QMan), Buffer Manager (BMan)
+    drivers/soc/fsl/qbman
+
+A simplified view of the dpaa_eth interfaces mapped to FMan MACs:
+
+  dpaa_eth       /eth0\     ...       /ethN\
+  driver        |      |             |      |
+  -------------   ----   -----------   ----   -------------
+       -Ports  / Tx  Rx \    ...    / Tx  Rx \
+  FMan        |          |         |          |
+       -MACs  |   MAC0   |         |   MACN   |
+             /   dtsec0   \  ...  /   dtsecN   \ (or tgec)
+            /              \     /              \(or memac)
+  ---------  --------------  ---  --------------  ---------
+      FMan, FMan Port, FMan SP, FMan MURAM drivers
+  ---------------------------------------------------------
+      FMan HW blocks: MURAM, MACs, Ports, SP
+  ---------------------------------------------------------
+
+The dpaa_eth relation to the QMan, BMan and FMan:
+              ________________________________
+  dpaa_eth   /            eth0                \
+  driver    /                                  \
+  ---------   -^-   -^-   -^-   ---    ---------
+  QMan driver / \   / \   / \  \   /  | BMan    |
+             |Rx | |Rx | |Tx | |Tx |  | driver  |
+  ---------  |Dfl| |Err| |Cnf| |FQs|  |         |
+  QMan HW    |FQ | |FQ | |FQs| |   |  |         |
+             /   \ /   \ /   \  \ /   |         |
+  ---------   ---   ---   ---   -v-    ---------
+            |        FMan QMI         |         |
+            | FMan HW       FMan BMI  | BMan HW |
+              -----------------------   --------
+
+where the acronyms used above (and in the code) are:
+DPAA = Data Path Acceleration Architecture
+FMan = DPAA Frame Manager
+QMan = DPAA Queue Manager
+BMan = DPAA Buffers Manager
+QMI = QMan interface in FMan
+BMI = BMan interface in FMan
+FMan SP = FMan Storage Profiles
+MURAM = Multi-user RAM in FMan
+FQ = QMan Frame Queue
+Rx Dfl FQ = default reception FQ
+Rx Err FQ = Rx error frames FQ
+Tx Cnf FQ = Tx confirmation FQs
+Tx FQs = transmission frame queues
+dtsec = datapath three speed Ethernet controller (10/100/1000 Mbps)
+tgec = ten gigabit Ethernet controller (10 Gbps)
+memac = multirate Ethernet MAC (10/100/1000/10000)
+
+DPAA Ethernet Supported SoCs
+============================
+
+The DPAA drivers enable the Ethernet controllers present on the following SoCs:
+
+# PPC
+P1023
+P2041
+P3041
+P4080
+P5020
+P5040
+T1023
+T1024
+T1040
+T1042
+T2080
+T4240
+B4860
+
+# ARM
+LS1043A
+LS1046A
+
+Configuring DPAA Ethernet in your kernel
+========================================
+
+To enable the DPAA Ethernet driver, the following Kconfig options are required:
+
+# common for arch/arm64 and arch/powerpc platforms
+CONFIG_FSL_DPAA=y
+CONFIG_FSL_FMAN=y
+CONFIG_FSL_DPAA_ETH=y
+CONFIG_FSL_XGMAC_MDIO=y
+
+# for arch/powerpc only
+CONFIG_FSL_PAMU=y
+
+# common options needed for the PHYs used on the RDBs
+CONFIG_VITESSE_PHY=y
+CONFIG_REALTEK_PHY=y
+CONFIG_AQUANTIA_PHY=y
+
+DPAA Ethernet Frame Processing
+==============================
+
+On Rx, buffers for the incoming frames are retrieved from one of the three
+existing buffers pools. The driver initializes and seeds these, each with
+buffers of different sizes: 1KB, 2KB and 4KB.
+
+On Tx, all transmitted frames are returned to the driver through Tx
+confirmation frame queues. The driver is then responsible for freeing the
+buffers. In order to do this properly, a backpointer is added to the buffer
+before transmission that points to the skb. When the buffer returns to the
+driver on a confirmation FQ, the skb can be correctly consumed.
+
+DPAA Ethernet Features
+======================
+
+Currently the DPAA Ethernet driver enables the basic features required for
+a Linux Ethernet driver. The support for advanced features will be added
+gradually.
+
+The driver has Rx and Tx checksum offloading for UDP and TCP. Currently the Rx
+checksum offload feature is enabled by default and cannot be controlled through
+ethtool.
+
+The driver has support for multiple prioritized Tx traffic classes. Priorities
+range from 0 (lowest) to 3 (highest). These are mapped to HW workqueues with
+strict priority levels. Each traffic class contains NR_CPU TX queues. By
+default, only one traffic class is enabled and the lowest priority Tx queues
+are used. Higher priority traffic classes can be enabled with the mqprio
+qdisc. For example, all four traffic classes are enabled on an interface with
+the following command. Furthermore, skb priority levels are mapped to traffic
+classes as follows:
+
+	* priorities 0 to 3 - traffic class 0 (low priority)
+	* priorities 4 to 7 - traffic class 1 (medium-low priority)
+	* priorities 8 to 11 - traffic class 2 (medium-high priority)
+	* priorities 12 to 15 - traffic class 3 (high priority)
+
+tc qdisc add dev <int> root handle 1: \
+	 mqprio num_tc 4 map 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 hw 1
+
+Debugging
+=========
+
+The following statistics are exported for each interface through ethtool:
+
+	- interrupt count per CPU
+	- Rx packets count per CPU
+	- Tx packets count per CPU
+	- Tx confirmed packets count per CPU
+	- Tx S/G frames count per CPU
+	- Tx error count per CPU
+	- Rx error count per CPU
+	- Rx error count per type
+	- congestion related statistics:
+		- congestion status
+		- time spent in congestion
+		- number of time the device entered congestion
+		- dropped packets count per cause
+
+The driver also exports the following information in sysfs:
+
+	- the FQ IDs for each FQ type
+	/sys/devices/platform/dpaa-ethernet.0/net/<int>/fqids
+
+	- the IDs of the buffer pools in use
+	/sys/devices/platform/dpaa-ethernet.0/net/<int>/bpids
diff --git a/Documentation/networking/scaling.txt b/Documentation/networking/scaling.txt
index 59f4db2a0c85..f55639d71d35 100644
--- a/Documentation/networking/scaling.txt
+++ b/Documentation/networking/scaling.txt
@@ -122,7 +122,7 @@ associated flow of the packet. The hash is either provided by hardware
 or will be computed in the stack. Capable hardware can pass the hash in
 the receive descriptor for the packet; this would usually be the same
 hash used for RSS (e.g. computed Toeplitz hash). The hash is saved in
-skb->rx_hash and can be used elsewhere in the stack as a hash of the
+skb->hash and can be used elsewhere in the stack as a hash of the
 packet’s flow.
 
 Each receive hardware queue has an associated list of CPUs to which
diff --git a/Documentation/networking/tcp.txt b/Documentation/networking/tcp.txt
index bdc4c0db51e1..9c7139d57e57 100644
--- a/Documentation/networking/tcp.txt
+++ b/Documentation/networking/tcp.txt
@@ -1,7 +1,7 @@
 TCP protocol
 ============
 
-Last updated: 9 February 2008
+Last updated: 3 June 2017
 
 Contents
 ========
@@ -29,18 +29,19 @@ As of 2.6.13, Linux supports pluggable congestion control algorithms.
 A congestion control mechanism can be registered through functions in
 tcp_cong.c. The functions used by the congestion control mechanism are
 registered via passing a tcp_congestion_ops struct to
-tcp_register_congestion_control. As a minimum name, ssthresh,
-cong_avoid must be valid.
+tcp_register_congestion_control. As a minimum, the congestion control
+mechanism must provide a valid name and must implement either ssthresh,
+cong_avoid and undo_cwnd hooks or the "omnipotent" cong_control hook.
 
 Private data for a congestion control mechanism is stored in tp->ca_priv.
 tcp_ca(tp) returns a pointer to this space.  This is preallocated space - it
 is important to check the size of your private data will fit this space, or
-alternatively space could be allocated elsewhere and a pointer to it could
+alternatively, space could be allocated elsewhere and a pointer to it could
 be stored here.
 
 There are three kinds of congestion control algorithms currently: The
 simplest ones are derived from TCP reno (highspeed, scalable) and just
-provide an alternative the congestion window calculation. More complex
+provide an alternative congestion window calculation. More complex
 ones like BIC try to look at other events to provide better
 heuristics.  There are also round trip time based algorithms like
 Vegas and Westwood+.
@@ -49,21 +50,15 @@ Good TCP congestion control is a complex problem because the algorithm
 needs to maintain fairness and performance. Please review current
 research and RFC's before developing new modules.
 
-The method that is used to determine which congestion control mechanism is
-determined by the setting of the sysctl net.ipv4.tcp_congestion_control.
-The default congestion control will be the last one registered (LIFO);
-so if you built everything as modules, the default will be reno. If you
-build with the defaults from Kconfig, then CUBIC will be builtin (not a
-module) and it will end up the default.
+The default congestion control mechanism is chosen based on the
+DEFAULT_TCP_CONG Kconfig parameter. If you really want a particular default
+value then you can set it using sysctl net.ipv4.tcp_congestion_control. The
+module will be autoloaded if needed and you will get the expected protocol. If
+you ask for an unknown congestion method, then the sysctl attempt will fail.
 
-If you really want a particular default value then you will need
-to set it with the sysctl.  If you use a sysctl, the module will be autoloaded
-if needed and you will get the expected protocol. If you ask for an
-unknown congestion method, then the sysctl attempt will fail.
-
-If you remove a tcp congestion control module, then you will get the next
+If you remove a TCP congestion control module, then you will get the next
 available one. Since reno cannot be built as a module, and cannot be
-deleted, it will always be available.
+removed, it will always be available.
 
 How the new TCP output machine [nyi] works.
 ===========================================
diff --git a/Documentation/sound/soc/dapm.rst b/Documentation/sound/soc/dapm.rst
index a27f42befa4d..8e44107933ab 100644
--- a/Documentation/sound/soc/dapm.rst
+++ b/Documentation/sound/soc/dapm.rst
@@ -105,6 +105,24 @@ Pre
 	Special PRE widget (exec before all others)
 Post
 	Special POST widget (exec after all others)
+Buffer
+	Inter widget audio data buffer within a DSP.
+Scheduler
+	DSP internal scheduler that schedules component/pipeline processing
+	work.
+Effect
+	Widget that performs an audio processing effect.
+SRC
+	Sample Rate Converter within DSP or CODEC
+ASRC
+	Asynchronous Sample Rate Converter within DSP or CODEC
+Encoder
+	Widget that encodes audio data from one format (usually PCM) to another
+	usually more compressed format.
+Decoder
+	Widget that decodes audio data from a compressed format to an
+	uncompressed format like PCM.
+
 
 (Widgets are defined in include/sound/soc-dapm.h)