[ARM] 5130/4: Support for the at91sam9g20

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 218 insertions, 0 deletions

diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
new file mode 100644
index 000000000000..45617c201240
--- /dev/null
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -0,0 +1,218 @@
+/*
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2008 Atmel
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/at73c213.h>
+#include <linux/clk.h>
+
+#include <asm/hardware.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/arch/board.h>
+#include <asm/arch/gpio.h>
+
+#include "generic.h"
+
+
+static void __init ek_map_io(void)
+{
+	/* Initialize processor: 18.432 MHz crystal */
+	at91sam9260_initialize(18432000);
+
+	/* DGBU on ttyS0. (Rx & Tx only) */
+	at91_register_uart(0, 0, 0);
+
+	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
+	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
+			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
+			   | ATMEL_UART_RI);
+
+	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
+	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
+
+	/* set serial console to ttyS0 (ie, DBGU) */
+	at91_set_serial_console(0);
+}
+
+static void __init ek_init_irq(void)
+{
+	at91sam9260_init_interrupts(NULL);
+}
+
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PC5,
+	.pullup_pin	= 0,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if !defined(CONFIG_MMC_AT91)
+	{	/* DataFlash chip */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 1,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+#endif
+};
+
+
+/*
+ * MACB Ethernet device
+ */
+static struct at91_eth_data __initdata ek_macb_data = {
+	.phy_irq_pin	= AT91_PIN_PA7,
+	.is_rmii	= 1,
+};
+
+
+/*
+ * NAND flash
+ */
+static struct mtd_partition __initdata ek_nand_partition[] = {
+	{
+		.name   = "Bootstrap",
+		.offset = 0,
+		.size   = 4 * 1024 * 1024,
+	},
+	{
+		.name	= "Partition 1",
+		.offset	= 4 * 1024 * 1024,
+		.size	= 60 * 1024 * 1024,
+	},
+	{
+		.name	= "Partition 2",
+		.offset	= 64 * 1024 * 1024,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
+{
+	*num_partitions = ARRAY_SIZE(ek_nand_partition);
+	return ek_nand_partition;
+}
+
+/* det_pin is not connected */
+static struct at91_nand_data __initdata ek_nand_data = {
+	.ale		= 21,
+	.cle		= 22,
+	.rdy_pin	= AT91_PIN_PC13,
+	.enable_pin	= AT91_PIN_PC14,
+	.partition_info	= nand_partitions,
+#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+	.bus_width_16	= 1,
+#else
+	.bus_width_16	= 0,
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ * det_pin, wp_pin and vcc_pin are not connected
+ */
+static struct at91_mmc_data __initdata ek_mmc_data = {
+	.slot_b		= 1,
+	.wire4		= 1,
+};
+
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+	{	/* "bottom" led, green, userled1 to be defined */
+		.name			= "ds5",
+		.gpio			= AT91_PIN_PA6,
+		.active_low		= 1,
+		.default_trigger	= "none",
+	},
+	{	/* "power" led, yellow */
+		.name			= "ds1",
+		.gpio			= AT91_PIN_PA9,
+		.default_trigger	= "heartbeat",
+	}
+};
+
+static void __init ek_board_init(void)
+{
+	/* Serial */
+	at91_add_device_serial();
+	/* USB Host */
+	at91_add_device_usbh(&ek_usbh_data);
+	/* USB Device */
+	at91_add_device_udc(&ek_udc_data);
+	/* SPI */
+	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
+	/* NAND */
+	at91_add_device_nand(&ek_nand_data);
+	/* Ethernet */
+	at91_add_device_eth(&ek_macb_data);
+	/* MMC */
+	at91_add_device_mmc(0, &ek_mmc_data);
+	/* I2C */
+	at91_add_device_i2c(NULL, 0);
+	/* LEDs */
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
+
+MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
+	/* Maintainer: Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END