Merge tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull gpio updates from Linus Walleij:
 "This is the bulk of the GPIO changes for the v5.2 kernel cycle. A bit
  later than usual because I was ironing out my own mistakes. I'm
  holding some stuff back for the next kernel as a result, and this
  should be a healthy and well tested batch.

  Core changes:

   - The gpiolib MMIO driver has been enhanced to handle two direction
     registers, i.e. one register to set lines as input and one register
     to set lines as output. It turns out some silicon engineer thinks
     the ability to configure a line as input and output at the same
     time makes sense, this can be debated but includes a lot of analog
     electronics reasoning, and the registers are there and need to be
     handled consistently. Unsurprisingly, we enforce the lines to be
     either inputs or outputs in such schemes.

   - Send in the proper argument value to .set_config() dispatched to
     the pin control subsystem. Nobody used it before, now someone does,
     so fix it to work as expected.

   - The ACPI gpiolib portions can now handle pin bias setting (pull up
     or pull down). This has been in the ACPI spec for years and we
     finally have it properly integrated with Linux GPIOs. It was based
     on an observation from Andy Schevchenko that Thomas Petazzoni's
     changes to the core for biasing the PCA950x GPIO expander actually
     happen to fit hand-in-glove with what the ACPI core needed. Such
     nice synergies happen sometimes.

  New drivers:

   - A new driver for the Mellanox BlueField GPIO controller. This is
     using 64bit MMIO registers and can configure lines as inputs and
     outputs at the same time and after improving the MMIO library we
     handle it just fine. Interesting.

   - A new IXP4xx proper gpiochip driver with hierarchical interrupts
     should be coming in from the ARM SoC tree as well.

  Driver enhancements:

   - The PCA053x driver handles the CAT9554 GPIO expander.

   - The PCA053x driver handles the NXP PCAL6416 GPIO expander.

   - Wake-up support on PCA053x GPIO lines.

   - OMAP now does a nice asynchronous IRQ handling on wake-ups by
     letting everything wake up on edges, and this makes runtime PM work
     as expected too.

  Misc:

   - Several cleanups such as devres fixes.

   - Get rid of some languager comstructs that cause problems when
     compiling with LLVMs clang.

   - Documentation review and update"

* tag 'gpio-v5.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
  gpio: Update documentation
  docs: gpio: convert docs to ReST and rename to *.rst
  gpio: sch: Remove write-only core_base
  gpio: pxa: Make two symbols static
  gpiolib: acpi: Respect pin bias setting
  gpiolib: acpi: Add acpi_gpio_update_gpiod_lookup_flags() helper
  gpiolib: acpi: Set pin value, based on bias, more accurately
  gpiolib: acpi: Change type of dflags
  gpiolib: Introduce GPIO_LOOKUP_FLAGS_DEFAULT
  gpiolib: Make use of enum gpio_lookup_flags consistent
  gpiolib: Indent entry values of enum gpio_lookup_flags
  gpio: pca953x: add support for pca6416
  dt-bindings: gpio: pca953x: document the nxp,pca6416
  gpio: pca953x: add pcal6416 to the of_device_id table
  gpio: gpio-omap: Remove conditional pm_runtime handling for GPIO interrupts
  gpio: gpio-omap: configure edge detection for level IRQs for idle wakeup
  tracing: stop making gpio tracing configurable
  gpio: pca953x: Configure wake-up path when wake-up is enabled
  gpio: of: Optimize quirk checks
  gpio: mmio: Drop bgpio_dir_inverted
  ...

1 files changed, 44 insertions, 39 deletions

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 0f91600c27ae..9370276fe7fe 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -26,12 +26,12 @@ config GPIOLIB_FASTPATH_LIMIT
 	range 32 512
 	default 512
 	help
-	   This adjusts the point at which certain APIs will switch from
-	   using a stack allocated buffer to a dynamically allocated buffer.
+	  This adjusts the point at which certain APIs will switch from
+	  using a stack allocated buffer to a dynamically allocated buffer.
 
-	   You shouldn't need to change this unless you really need to
-	   optimize either stack space or performance. Change this carefully
-	   since setting an incorrect value could cause stack corruption.
+	  You shouldn't need to change this unless you really need to
+	  optimize either stack space or performance. Change this carefully
+	  since setting an incorrect value could cause stack corruption.
 
 config OF_GPIO
 	def_bool y
@@ -319,7 +319,7 @@ config GPIO_MENZ127
 	depends on MCB
 	select GPIO_GENERIC
 	help
-	 Say yes here to support the MEN 16Z127 GPIO Controller
+	  Say yes here to support the MEN 16Z127 GPIO Controller
 
 config GPIO_MM_LANTIQ
 	bool "Lantiq Memory mapped GPIOs"
@@ -329,20 +329,6 @@ config GPIO_MM_LANTIQ
 	  (EBU) found on Lantiq SoCs. The gpios are output only as they are
 	  created by attaching a 16bit latch to the bus.
 
-config GPIO_MOCKUP
-	tristate "GPIO Testing Driver"
-	depends on GPIOLIB && SYSFS
-	select GPIO_SYSFS
-	select GPIOLIB_IRQCHIP
-	select IRQ_SIM
-	help
-	  This enables GPIO Testing driver, which provides a way to test GPIO
-	  subsystem through sysfs(or char device) and debugfs. GPIO_SYSFS
-	  must be selected for this test.
-	  User could use it through the script in
-	  tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
-	  it.
-
 config GPIO_MPC5200
 	def_bool y
 	depends on PPC_MPC52xx
@@ -861,11 +847,11 @@ config GPIO_MAX732X
 	  Input and Output (designed by 'P'). The combinations are listed
 	  below:
 
-	  8 bits:	max7319 (8I), max7320 (8O), max7321 (8P),
-		  	max7322 (4I4O), max7323 (4P4O)
+	  8 bits:       max7319 (8I), max7320 (8O), max7321 (8P),
+	                max7322 (4I4O), max7323 (4P4O)
 
-	  16 bits:	max7324 (8I8O), max7325 (8P8O),
-		  	max7326 (4I12O), max7327 (4P12O)
+	  16 bits:      max7324 (8I8O), max7325 (8P8O),
+	                max7326 (4I12O), max7327 (4P12O)
 
 	  Board setup code must specify the model to use, and the start
 	  number for these GPIOs.
@@ -892,17 +878,17 @@ config GPIO_PCA953X
 	  SMBus I/O expanders, made mostly by NXP or TI.  Compatible
 	  models include:
 
-	  4 bits:	pca9536, pca9537
+	  4 bits:       pca9536, pca9537
 
-	  8 bits:	max7310, max7315, pca6107, pca9534, pca9538, pca9554,
-			pca9556, pca9557, pca9574, tca6408, tca9554, xra1202
+	  8 bits:       max7310, max7315, pca6107, pca9534, pca9538, pca9554,
+	                pca9556, pca9557, pca9574, tca6408, tca9554, xra1202
 
-	  16 bits:	max7312, max7313, pca9535, pca9539, pca9555, pca9575,
-			tca6416
+	  16 bits:      max7312, max7313, pca9535, pca9539, pca9555, pca9575,
+	                tca6416
 
-	  24 bits:	tca6424
+	  24 bits:      tca6424
 
-	  40 bits:	pca9505, pca9698
+	  40 bits:      pca9505, pca9698
 
 config GPIO_PCA953X_IRQ
 	bool "Interrupt controller support for PCA953x"
@@ -924,7 +910,7 @@ config GPIO_PCF857X
 
 	  8 bits:   pcf8574, pcf8574a, pca8574, pca8574a,
 	            pca9670, pca9672, pca9674, pca9674a,
-	  	    max7328, max7329
+	            max7328, max7329
 
 	  16 bits:  pcf8575, pcf8575c, pca8575,
 	            pca9671, pca9673, pca9675
@@ -1046,9 +1032,9 @@ config HTC_EGPIO
 	bool "HTC EGPIO support"
 	depends on GPIOLIB && ARM
 	help
-	    This driver supports the CPLD egpio chip present on
-	    several HTC phones.  It provides basic support for input
-	    pins, output pins, and irqs.
+	  This driver supports the CPLD egpio chip present on
+	  several HTC phones.  It provides basic support for input
+	  pins, output pins, and irqs.
 
 config GPIO_JANZ_TTL
 	tristate "Janz VMOD-TTL Digital IO Module"
@@ -1084,7 +1070,7 @@ config GPIO_LP873X
 	  on LP873X PMICs.
 
 	  This driver can also be built as a module. If so, the module will be
-          called gpio-lp873x.
+	  called gpio-lp873x.
 
 config GPIO_LP87565
 	tristate "TI LP87565 GPIO"
@@ -1315,6 +1301,13 @@ config GPIO_MERRIFIELD
 	help
 	  Say Y here to support Intel Merrifield GPIO.
 
+config GPIO_MLXBF
+	tristate "Mellanox BlueField SoC GPIO"
+	depends on (MELLANOX_PLATFORM && ARM64 && ACPI) || (64BIT && COMPILE_TEST)
+	select GPIO_GENERIC
+	help
+	  Say Y here if you want GPIO support on Mellanox BlueField SoC.
+
 config GPIO_ML_IOH
 	tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
 	depends on X86 || COMPILE_TEST
@@ -1435,10 +1428,22 @@ config GPIO_VIPERBOARD
 	  Say yes here to access the GPIO signals of Nano River
 	  Technologies Viperboard. There are two GPIO chips on the
 	  board: gpioa and gpiob.
-          See viperboard API specification and Nano
-          River Tech's viperboard.h for detailed meaning
-          of the module parameters.
+	  See viperboard API specification and Nano
+	  River Tech's viperboard.h for detailed meaning
+	  of the module parameters.
 
 endmenu
 
+config GPIO_MOCKUP
+	tristate "GPIO Testing Driver"
+	depends on GPIOLIB
+	select IRQ_SIM
+	help
+	  This enables GPIO Testing driver, which provides a way to test GPIO
+	  subsystem through sysfs(or char device) and debugfs. GPIO_SYSFS
+	  must be selected for this test.
+	  User could use it through the script in
+	  tools/testing/selftests/gpio/gpio-mockup.sh. Reference the usage in
+	  it.
+
 endif