Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6

1 files changed, 1415 insertions, 0 deletions

diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c
new file mode 100644
index 000000000000..59122cc0a50a
--- /dev/null
+++ b/drivers/hwmon/abituguru.c
@@ -0,0 +1,1415 @@
+/*
+    abituguru.c Copyright (c) 2005-2006 Hans de Goede <j.w.r.degoede@hhs.nl>
+
+    This program is free software; you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation; either version 2 of the License, or
+    (at your option) any later version.
+
+    This program is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program; if not, write to the Free Software
+    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+*/
+/*
+    This driver supports the sensor part of the custom Abit uGuru chip found
+    on Abit uGuru motherboards. Note: because of lack of specs the CPU / RAM /
+    etc voltage & frequency control is not supported!
+*/
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/jiffies.h>
+#include <linux/mutex.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <asm/io.h>
+
+/* Banks */
+#define ABIT_UGURU_ALARM_BANK			0x20 /* 1x 3 bytes */
+#define ABIT_UGURU_SENSOR_BANK1			0x21 /* 16x volt and temp */
+#define ABIT_UGURU_FAN_PWM			0x24 /* 3x 5 bytes */
+#define ABIT_UGURU_SENSOR_BANK2			0x26 /* fans */
+/* max nr of sensors in bank1, a bank1 sensor can be in, temp or nc */
+#define ABIT_UGURU_MAX_BANK1_SENSORS		16
+/* Warning if you increase one of the 2 MAX defines below to 10 or higher you
+   should adjust the belonging _NAMES_LENGTH macro for the 2 digit number! */
+/* max nr of sensors in bank2, currently mb's with max 6 fans are known */
+#define ABIT_UGURU_MAX_BANK2_SENSORS		6
+/* max nr of pwm outputs, currently mb's with max 5 pwm outputs are known */
+#define ABIT_UGURU_MAX_PWMS			5
+/* uGuru sensor bank 1 flags */			     /* Alarm if: */
+#define ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE	0x01 /*  temp over warn */
+#define ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE	0x02 /*  volt over max */
+#define ABIT_UGURU_VOLT_LOW_ALARM_ENABLE	0x04 /*  volt under min */
+#define ABIT_UGURU_TEMP_HIGH_ALARM_FLAG		0x10 /* temp is over warn */
+#define ABIT_UGURU_VOLT_HIGH_ALARM_FLAG		0x20 /* volt is over max */
+#define ABIT_UGURU_VOLT_LOW_ALARM_FLAG		0x40 /* volt is under min */
+/* uGuru sensor bank 2 flags */			     /* Alarm if: */
+#define ABIT_UGURU_FAN_LOW_ALARM_ENABLE		0x01 /*   fan under min */
+/* uGuru sensor bank common flags */
+#define ABIT_UGURU_BEEP_ENABLE			0x08 /* beep if alarm */
+#define ABIT_UGURU_SHUTDOWN_ENABLE		0x80 /* shutdown if alarm */
+/* uGuru fan PWM (speed control) flags */
+#define ABIT_UGURU_FAN_PWM_ENABLE		0x80 /* enable speed control */
+/* Values used for conversion */
+#define ABIT_UGURU_FAN_MAX			15300 /* RPM */
+/* Bank1 sensor types */
+#define ABIT_UGURU_IN_SENSOR			0
+#define ABIT_UGURU_TEMP_SENSOR			1
+#define ABIT_UGURU_NC				2
+/* Timeouts / Retries, if these turn out to need a lot of fiddling we could
+   convert them to params. */
+/* 250 was determined by trial and error, 200 works most of the time, but not
+   always. I assume this is cpu-speed independent, since the ISA-bus and not
+   the CPU should be the bottleneck. Note that 250 sometimes is still not
+   enough (only reported on AN7 mb) this is handled by a higher layer. */
+#define ABIT_UGURU_WAIT_TIMEOUT			250
+/* Normally all expected status in abituguru_ready, are reported after the
+   first read, but sometimes not and we need to poll, 5 polls was not enough
+   50 sofar is. */
+#define ABIT_UGURU_READY_TIMEOUT		50
+/* Maximum 3 retries on timedout reads/writes, delay 200 ms before retrying */
+#define ABIT_UGURU_MAX_RETRIES			3
+#define ABIT_UGURU_RETRY_DELAY			(HZ/5)
+/* Maximum 2 timeouts in abituguru_update_device, iow 3 in a row is an error */
+#define ABIT_UGURU_MAX_TIMEOUTS			2
+/* utility macros */
+#define ABIT_UGURU_NAME				"abituguru"
+#define ABIT_UGURU_DEBUG(level, format, arg...)				\
+	if (level <= verbose)						\
+		printk(KERN_DEBUG ABIT_UGURU_NAME ": "	format , ## arg)
+/* Macros to help calculate the sysfs_names array length */
+/* sum of strlen of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0,
+   in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0 */
+#define ABITUGURU_IN_NAMES_LENGTH	(11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14)
+/* sum of strlen of: temp??_input\0, temp??_max\0, temp??_crit\0,
+   temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0 */
+#define ABITUGURU_TEMP_NAMES_LENGTH	(13 + 11 + 12 + 13 + 20 + 12 + 16)
+/* sum of strlen of: fan?_input\0, fan?_min\0, fan?_alarm\0,
+   fan?_alarm_enable\0, fan?_beep\0, fan?_shutdown\0 */
+#define ABITUGURU_FAN_NAMES_LENGTH	(11 + 9 + 11 + 18 + 10 + 14)
+/* sum of strlen of: pwm?_enable\0, pwm?_auto_channels_temp\0,
+   pwm?_auto_point{1,2}_pwm\0, pwm?_auto_point{1,2}_temp\0 */
+#define ABITUGURU_PWM_NAMES_LENGTH	(12 + 24 + 2 * 21 + 2 * 22)
+/* IN_NAMES_LENGTH > TEMP_NAMES_LENGTH so assume all bank1 sensors are in */
+#define ABITUGURU_SYSFS_NAMES_LENGTH	( \
+	ABIT_UGURU_MAX_BANK1_SENSORS * ABITUGURU_IN_NAMES_LENGTH + \
+	ABIT_UGURU_MAX_BANK2_SENSORS * ABITUGURU_FAN_NAMES_LENGTH + \
+	ABIT_UGURU_MAX_PWMS * ABITUGURU_PWM_NAMES_LENGTH)
+
+/* All the macros below are named identical to the oguru and oguru2 programs
+   reverse engineered by Olle Sandberg, hence the names might not be 100%
+   logical. I could come up with better names, but I prefer keeping the names
+   identical so that this driver can be compared with his work more easily. */
+/* Two i/o-ports are used by uGuru */
+#define ABIT_UGURU_BASE				0x00E0
+/* Used to tell uGuru what to read and to read the actual data */
+#define ABIT_UGURU_CMD				0x00
+/* Mostly used to check if uGuru is busy */
+#define ABIT_UGURU_DATA				0x04
+#define ABIT_UGURU_REGION_LENGTH		5
+/* uGuru status' */
+#define ABIT_UGURU_STATUS_WRITE			0x00 /* Ready to be written */
+#define ABIT_UGURU_STATUS_READ			0x01 /* Ready to be read */
+#define ABIT_UGURU_STATUS_INPUT			0x08 /* More input */
+#define ABIT_UGURU_STATUS_READY			0x09 /* Ready to be written */
+
+/* Constants */
+/* in (Volt) sensors go up to 3494 mV, temp to 255000 millidegrees Celsius */
+static const int abituguru_bank1_max_value[2] = { 3494, 255000 };
+/* Min / Max allowed values for sensor2 (fan) alarm threshold, these values
+   correspond to 300-3000 RPM */
+static const u8 abituguru_bank2_min_threshold = 5;
+static const u8 abituguru_bank2_max_threshold = 50;
+/* Register 0 is a bitfield, 1 and 2 are pwm settings (255 = 100%), 3 and 4
+   are temperature trip points. */
+static const int abituguru_pwm_settings_multiplier[5] = { 0, 1, 1, 1000, 1000 };
+/* Min / Max allowed values for pwm_settings. Note: pwm1 (CPU fan) is a
+   special case the minium allowed pwm% setting for this is 30% (77) on
+   some MB's this special case is handled in the code! */
+static const u8 abituguru_pwm_min[5] = { 0, 170, 170, 25, 25 };
+static const u8 abituguru_pwm_max[5] = { 0, 255, 255, 75, 75 };
+
+
+/* Insmod parameters */
+static int force;
+module_param(force, bool, 0);
+MODULE_PARM_DESC(force, "Set to one to force detection.");
+static int fan_sensors;
+module_param(fan_sensors, int, 0);
+MODULE_PARM_DESC(fan_sensors, "Number of fan sensors on the uGuru "
+	"(0 = autodetect)");
+static int pwms;
+module_param(pwms, int, 0);
+MODULE_PARM_DESC(pwms, "Number of PWMs on the uGuru "
+	"(0 = autodetect)");
+
+/* Default verbose is 2, since this driver is still in the testing phase */
+static int verbose = 2;
+module_param(verbose, int, 0644);
+MODULE_PARM_DESC(verbose, "How verbose should the driver be? (0-3):\n"
+	"   0 normal output\n"
+	"   1 + verbose error reporting\n"
+	"   2 + sensors type probing info\n"
+	"   3 + retryable error reporting");
+
+
+/* For the Abit uGuru, we need to keep some data in memory.
+   The structure is dynamically allocated, at the same time when a new
+   abituguru device is allocated. */
+struct abituguru_data {
+	struct class_device *class_dev; /* hwmon registered device */
+	struct mutex update_lock;	/* protect access to data and uGuru */
+	unsigned long last_updated;	/* In jiffies */
+	unsigned short addr;		/* uguru base address */
+	char uguru_ready;		/* is the uguru in ready state? */
+	unsigned char update_timeouts;	/* number of update timeouts since last
+					   successful update */
+
+	/* The sysfs attr and their names are generated automatically, for bank1
+	   we cannot use a predefined array because we don't know beforehand
+	   of a sensor is a volt or a temp sensor, for bank2 and the pwms its
+	   easier todo things the same way.  For in sensors we have 9 (temp 7)
+	   sysfs entries per sensor, for bank2 and pwms 6. */
+	struct sensor_device_attribute_2 sysfs_attr[
+		ABIT_UGURU_MAX_BANK1_SENSORS * 9 +
+		ABIT_UGURU_MAX_BANK2_SENSORS * 6 + ABIT_UGURU_MAX_PWMS * 6];
+	/* Buffer to store the dynamically generated sysfs names */
+	char sysfs_names[ABITUGURU_SYSFS_NAMES_LENGTH];
+
+	/* Bank 1 data */
+	/* number of and addresses of [0] in, [1] temp sensors */
+	u8 bank1_sensors[2];
+	u8 bank1_address[2][ABIT_UGURU_MAX_BANK1_SENSORS];
+	u8 bank1_value[ABIT_UGURU_MAX_BANK1_SENSORS];
+	/* This array holds 3 entries per sensor for the bank 1 sensor settings
+	   (flags, min, max for voltage / flags, warn, shutdown for temp). */
+	u8 bank1_settings[ABIT_UGURU_MAX_BANK1_SENSORS][3];
+	/* Maximum value for each sensor used for scaling in mV/millidegrees
+	   Celsius. */
+	int bank1_max_value[ABIT_UGURU_MAX_BANK1_SENSORS];
+
+	/* Bank 2 data, ABIT_UGURU_MAX_BANK2_SENSORS entries for bank2 */
+	u8 bank2_sensors; /* actual number of bank2 sensors found */
+	u8 bank2_value[ABIT_UGURU_MAX_BANK2_SENSORS];
+	u8 bank2_settings[ABIT_UGURU_MAX_BANK2_SENSORS][2]; /* flags, min */
+
+	/* Alarms 2 bytes for bank1, 1 byte for bank2 */
+	u8 alarms[3];
+
+	/* Fan PWM (speed control) 5 bytes per PWM */
+	u8 pwms; /* actual number of pwms found */
+	u8 pwm_settings[ABIT_UGURU_MAX_PWMS][5];
+};
+
+/* wait till the uguru is in the specified state */
+static int abituguru_wait(struct abituguru_data *data, u8 state)
+{
+	int timeout = ABIT_UGURU_WAIT_TIMEOUT;
+
+	while (inb_p(data->addr + ABIT_UGURU_DATA) != state) {
+		timeout--;
+		if (timeout == 0)
+			return -EBUSY;
+	}
+	return 0;
+}
+
+/* Put the uguru in ready for input state */
+static int abituguru_ready(struct abituguru_data *data)
+{
+	int timeout = ABIT_UGURU_READY_TIMEOUT;
+
+	if (data->uguru_ready)
+		return 0;
+
+	/* Reset? / Prepare for next read/write cycle */
+	outb(0x00, data->addr + ABIT_UGURU_DATA);
+
+	/* Wait till the uguru is ready */
+	if (abituguru_wait(data, ABIT_UGURU_STATUS_READY)) {
+		ABIT_UGURU_DEBUG(1,
+			"timeout exceeded waiting for ready state\n");
+		return -EIO;
+	}
+
+	/* Cmd port MUST be read now and should contain 0xAC */
+	while (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
+		timeout--;
+		if (timeout == 0) {
+			ABIT_UGURU_DEBUG(1,
+			   "CMD reg does not hold 0xAC after ready command\n");
+			return -EIO;
+		}
+	}
+
+	/* After this the ABIT_UGURU_DATA port should contain
+	   ABIT_UGURU_STATUS_INPUT */
+	timeout = ABIT_UGURU_READY_TIMEOUT;
+	while (inb_p(data->addr + ABIT_UGURU_DATA) != ABIT_UGURU_STATUS_INPUT) {
+		timeout--;
+		if (timeout == 0) {
+			ABIT_UGURU_DEBUG(1,
+				"state != more input after ready command\n");
+			return -EIO;
+		}
+	}
+
+	data->uguru_ready = 1;
+	return 0;
+}
+
+/* Send the bank and then sensor address to the uGuru for the next read/write
+   cycle. This function gets called as the first part of a read/write by
+   abituguru_read and abituguru_write. This function should never be
+   called by any other function. */
+static int abituguru_send_address(struct abituguru_data *data,
+	u8 bank_addr, u8 sensor_addr, int retries)
+{
+	/* assume the caller does error handling itself if it has not requested
+	   any retries, and thus be quiet. */
+	int report_errors = retries;
+
+	for (;;) {
+		/* Make sure the uguru is ready and then send the bank address,
+		   after this the uguru is no longer "ready". */
+		if (abituguru_ready(data) != 0)
+			return -EIO;
+		outb(bank_addr, data->addr + ABIT_UGURU_DATA);
+		data->uguru_ready = 0;
+
+		/* Wait till the uguru is ABIT_UGURU_STATUS_INPUT state again
+		   and send the sensor addr */
+		if (abituguru_wait(data, ABIT_UGURU_STATUS_INPUT)) {
+			if (retries) {
+				ABIT_UGURU_DEBUG(3, "timeout exceeded "
+					"waiting for more input state, %d "
+					"tries remaining\n", retries);
+				set_current_state(TASK_UNINTERRUPTIBLE);
+				schedule_timeout(ABIT_UGURU_RETRY_DELAY);
+				retries--;
+				continue;
+			}
+			if (report_errors)
+				ABIT_UGURU_DEBUG(1, "timeout exceeded "
+					"waiting for more input state "
+					"(bank: %d)\n", (int)bank_addr);
+			return -EBUSY;
+		}
+		outb(sensor_addr, data->addr + ABIT_UGURU_CMD);
+		return 0;
+	}
+}
+
+/* Read count bytes from sensor sensor_addr in bank bank_addr and store the
+   result in buf, retry the send address part of the read retries times. */
+static int abituguru_read(struct abituguru_data *data,
+	u8 bank_addr, u8 sensor_addr, u8 *buf, int count, int retries)
+{
+	int i;
+
+	/* Send the address */
+	i = abituguru_send_address(data, bank_addr, sensor_addr, retries);
+	if (i)
+		return i;
+
+	/* And read the data */
+	for (i = 0; i < count; i++) {
+		if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
+			ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
+				"read state (bank: %d, sensor: %d)\n",
+				(int)bank_addr, (int)sensor_addr);
+			break;
+		}
+		buf[i] = inb(data->addr + ABIT_UGURU_CMD);
+	}
+
+	/* Last put the chip back in ready state */
+	abituguru_ready(data);
+
+	return i;
+}
+
+/* Write count bytes from buf to sensor sensor_addr in bank bank_addr, the send
+   address part of the write is always retried ABIT_UGURU_MAX_RETRIES times. */
+static int abituguru_write(struct abituguru_data *data,
+	u8 bank_addr, u8 sensor_addr, u8 *buf, int count)
+{
+	int i;
+
+	/* Send the address */
+	i = abituguru_send_address(data, bank_addr, sensor_addr,
+		ABIT_UGURU_MAX_RETRIES);
+	if (i)
+		return i;
+
+	/* And write the data */
+	for (i = 0; i < count; i++) {
+		if (abituguru_wait(data, ABIT_UGURU_STATUS_WRITE)) {
+			ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for "
+				"write state (bank: %d, sensor: %d)\n",
+				(int)bank_addr, (int)sensor_addr);
+			break;
+		}
+		outb(buf[i], data->addr + ABIT_UGURU_CMD);
+	}
+
+	/* Now we need to wait till the chip is ready to be read again,
+	   don't ask why */
+	if (abituguru_wait(data, ABIT_UGURU_STATUS_READ)) {
+		ABIT_UGURU_DEBUG(1, "timeout exceeded waiting for read state "
+			"after write (bank: %d, sensor: %d)\n", (int)bank_addr,
+			(int)sensor_addr);
+		return -EIO;
+	}
+
+	/* Cmd port MUST be read now and should contain 0xAC */
+	if (inb_p(data->addr + ABIT_UGURU_CMD) != 0xAC) {
+		ABIT_UGURU_DEBUG(1, "CMD reg does not hold 0xAC after write "
+			"(bank: %d, sensor: %d)\n", (int)bank_addr,
+			(int)sensor_addr);
+		return -EIO;
+	}
+
+	/* Last put the chip back in ready state */
+	abituguru_ready(data);
+
+	return i;
+}
+
+/* Detect sensor type. Temp and Volt sensors are enabled with
+   different masks and will ignore enable masks not meant for them.
+   This enables us to test what kind of sensor we're dealing with.
+   By setting the alarm thresholds so that we will always get an
+   alarm for sensor type X and then enabling the sensor as sensor type
+   X, if we then get an alarm it is a sensor of type X. */
+static int __devinit
+abituguru_detect_bank1_sensor_type(struct abituguru_data *data,
+				   u8 sensor_addr)
+{
+	u8 val, buf[3];
+	int ret = ABIT_UGURU_NC;
+
+	/* First read the sensor and the current settings */
+	if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, sensor_addr, &val,
+			1, ABIT_UGURU_MAX_RETRIES) != 1)
+		return -ENODEV;
+
+	/* Test val is sane / usable for sensor type detection. */
+	if ((val < 10u) || (val > 240u)) {
+		printk(KERN_WARNING ABIT_UGURU_NAME
+			": bank1-sensor: %d reading (%d) too close to limits, "
+			"unable to determine sensor type, skipping sensor\n",
+			(int)sensor_addr, (int)val);
+		/* assume no sensor is there for sensors for which we can't
+		   determine the sensor type because their reading is too close
+		   to their limits, this usually means no sensor is there. */
+		return ABIT_UGURU_NC;
+	}
+
+	ABIT_UGURU_DEBUG(2, "testing bank1 sensor %d\n", (int)sensor_addr);
+	/* Volt sensor test, enable volt low alarm, set min value ridicously
+	   high. If its a volt sensor this should always give us an alarm. */
+	buf[0] = ABIT_UGURU_VOLT_LOW_ALARM_ENABLE;
+	buf[1] = 245;
+	buf[2] = 250;
+	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
+			buf, 3) != 3)
+		return -ENODEV;
+	/* Now we need 20 ms to give the uguru time to read the sensors
+	   and raise a voltage alarm */
+	set_current_state(TASK_UNINTERRUPTIBLE);
+	schedule_timeout(HZ/50);
+	/* Check for alarm and check the alarm is a volt low alarm. */
+	if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
+			ABIT_UGURU_MAX_RETRIES) != 3)
+		return -ENODEV;
+	if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
+				sensor_addr, buf, 3,
+				ABIT_UGURU_MAX_RETRIES) != 3)
+			return -ENODEV;
+		if (buf[0] & ABIT_UGURU_VOLT_LOW_ALARM_FLAG) {
+			/* Restore original settings */
+			if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
+					sensor_addr,
+					data->bank1_settings[sensor_addr],
+					3) != 3)
+				return -ENODEV;
+			ABIT_UGURU_DEBUG(2, "  found volt sensor\n");
+			return ABIT_UGURU_IN_SENSOR;
+		} else
+			ABIT_UGURU_DEBUG(2, "  alarm raised during volt "
+				"sensor test, but volt low flag not set\n");
+	} else
+		ABIT_UGURU_DEBUG(2, "  alarm not raised during volt sensor "
+			"test\n");
+
+	/* Temp sensor test, enable sensor as a temp sensor, set beep value
+	   ridicously low (but not too low, otherwise uguru ignores it).
+	   If its a temp sensor this should always give us an alarm. */
+	buf[0] = ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE;
+	buf[1] = 5;
+	buf[2] = 10;
+	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
+			buf, 3) != 3)
+		return -ENODEV;
+	/* Now we need 50 ms to give the uguru time to read the sensors
+	   and raise a temp alarm */
+	set_current_state(TASK_UNINTERRUPTIBLE);
+	schedule_timeout(HZ/20);
+	/* Check for alarm and check the alarm is a temp high alarm. */
+	if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0, buf, 3,
+			ABIT_UGURU_MAX_RETRIES) != 3)
+		return -ENODEV;
+	if (buf[sensor_addr/8] & (0x01 << (sensor_addr % 8))) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1 + 1,
+				sensor_addr, buf, 3,
+				ABIT_UGURU_MAX_RETRIES) != 3)
+			return -ENODEV;
+		if (buf[0] & ABIT_UGURU_TEMP_HIGH_ALARM_FLAG) {
+			ret = ABIT_UGURU_TEMP_SENSOR;
+			ABIT_UGURU_DEBUG(2, "  found temp sensor\n");
+		} else
+			ABIT_UGURU_DEBUG(2, "  alarm raised during temp "
+				"sensor test, but temp high flag not set\n");
+	} else
+		ABIT_UGURU_DEBUG(2, "  alarm not raised during temp sensor "
+			"test\n");
+
+	/* Restore original settings */
+	if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2, sensor_addr,
+			data->bank1_settings[sensor_addr], 3) != 3)
+		return -ENODEV;
+
+	return ret;
+}
+
+/* These functions try to find out how many sensors there are in bank2 and how
+   many pwms there are. The purpose of this is to make sure that we don't give
+   the user the possibility to change settings for non-existent sensors / pwm.
+   The uGuru will happily read / write whatever memory happens to be after the
+   memory storing the PWM settings when reading/writing to a PWM which is not
+   there. Notice even if we detect a PWM which doesn't exist we normally won't
+   write to it, unless the user tries to change the settings.
+
+   Although the uGuru allows reading (settings) from non existing bank2
+   sensors, my version of the uGuru does seem to stop writing to them, the
+   write function above aborts in this case with:
+   "CMD reg does not hold 0xAC after write"
+
+   Notice these 2 tests are non destructive iow read-only tests, otherwise
+   they would defeat their purpose. Although for the bank2_sensors detection a
+   read/write test would be feasible because of the reaction above, I've
+   however opted to stay on the safe side. */
+static void __devinit
+abituguru_detect_no_bank2_sensors(struct abituguru_data *data)
+{
+	int i;
+
+	if (fan_sensors) {
+		data->bank2_sensors = fan_sensors;
+		ABIT_UGURU_DEBUG(2, "assuming %d fan sensors because of "
+			"\"fan_sensors\" module param\n",
+			(int)data->bank2_sensors);
+		return;
+	}
+
+	ABIT_UGURU_DEBUG(2, "detecting number of fan sensors\n");
+	for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
+		/* 0x89 are the known used bits:
+		   -0x80 enable shutdown
+		   -0x08 enable beep
+		   -0x01 enable alarm
+		   All other bits should be 0, but on some motherboards
+		   0x40 (bit 6) is also high for some of the fans?? */
+		if (data->bank2_settings[i][0] & ~0xC9) {
+			ABIT_UGURU_DEBUG(2, "  bank2 sensor %d does not seem "
+				"to be a fan sensor: settings[0] = %02X\n",
+				i, (unsigned int)data->bank2_settings[i][0]);
+			break;
+		}
+
+		/* check if the threshold is within the allowed range */
+		if (data->bank2_settings[i][1] <
+				abituguru_bank2_min_threshold) {
+			ABIT_UGURU_DEBUG(2, "  bank2 sensor %d does not seem "
+				"to be a fan sensor: the threshold (%d) is "
+				"below the minimum (%d)\n", i,
+				(int)data->bank2_settings[i][1],
+				(int)abituguru_bank2_min_threshold);
+			break;
+		}
+		if (data->bank2_settings[i][1] >
+				abituguru_bank2_max_threshold) {
+			ABIT_UGURU_DEBUG(2, "  bank2 sensor %d does not seem "
+				"to be a fan sensor: the threshold (%d) is "
+				"above the maximum (%d)\n", i,
+				(int)data->bank2_settings[i][1],
+				(int)abituguru_bank2_max_threshold);
+			break;
+		}
+	}
+
+	data->bank2_sensors = i;
+	ABIT_UGURU_DEBUG(2, " found: %d fan sensors\n",
+		(int)data->bank2_sensors);
+}
+
+static void __devinit
+abituguru_detect_no_pwms(struct abituguru_data *data)
+{
+	int i, j;
+
+	if (pwms) {
+		data->pwms = pwms;
+		ABIT_UGURU_DEBUG(2, "assuming %d PWM outputs because of "
+			"\"pwms\" module param\n", (int)data->pwms);
+		return;
+	}
+
+	ABIT_UGURU_DEBUG(2, "detecting number of PWM outputs\n");
+	for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
+		/* 0x80 is the enable bit and the low
+		   nibble is which temp sensor to use,
+		   the other bits should be 0 */
+		if (data->pwm_settings[i][0] & ~0x8F) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: settings[0] = %02X\n",
+				i, (unsigned int)data->pwm_settings[i][0]);
+			break;
+		}
+
+		/* the low nibble must correspond to one of the temp sensors
+		   we've found */
+		for (j = 0; j < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR];
+				j++) {
+			if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][j] ==
+					(data->pwm_settings[i][0] & 0x0F))
+				break;
+		}
+		if (j == data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: %d is not a valid temp "
+				"sensor address\n", i,
+				data->pwm_settings[i][0] & 0x0F);
+			break;
+		}
+
+		/* check if all other settings are within the allowed range */
+		for (j = 1; j < 5; j++) {
+			u8 min;
+			/* special case pwm1 min pwm% */
+			if ((i == 0) && ((j == 1) || (j == 2)))
+				min = 77;
+			else
+				min = abituguru_pwm_min[j];
+			if (data->pwm_settings[i][j] < min) {
+				ABIT_UGURU_DEBUG(2, "  pwm channel %d does "
+					"not seem to be a pwm channel: "
+					"setting %d (%d) is below the minimum "
+					"value (%d)\n", i, j,
+					(int)data->pwm_settings[i][j],
+					(int)min);
+				goto abituguru_detect_no_pwms_exit;
+			}
+			if (data->pwm_settings[i][j] > abituguru_pwm_max[j]) {
+				ABIT_UGURU_DEBUG(2, "  pwm channel %d does "
+					"not seem to be a pwm channel: "
+					"setting %d (%d) is above the maximum "
+					"value (%d)\n", i, j,
+					(int)data->pwm_settings[i][j],
+					(int)abituguru_pwm_max[j]);
+				goto abituguru_detect_no_pwms_exit;
+			}
+		}
+
+		/* check that min temp < max temp and min pwm < max pwm */
+		if (data->pwm_settings[i][1] >= data->pwm_settings[i][2]) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: min pwm (%d) >= "
+				"max pwm (%d)\n", i,
+				(int)data->pwm_settings[i][1],
+				(int)data->pwm_settings[i][2]);
+			break;
+		}
+		if (data->pwm_settings[i][3] >= data->pwm_settings[i][4]) {
+			ABIT_UGURU_DEBUG(2, "  pwm channel %d does not seem "
+				"to be a pwm channel: min temp (%d) >= "
+				"max temp (%d)\n", i,
+				(int)data->pwm_settings[i][3],
+				(int)data->pwm_settings[i][4]);
+			break;
+		}
+	}
+
+abituguru_detect_no_pwms_exit:
+	data->pwms = i;
+	ABIT_UGURU_DEBUG(2, " found: %d PWM outputs\n", (int)data->pwms);
+}
+
+/* Following are the sysfs callback functions. These functions expect:
+   sensor_device_attribute_2->index:   sensor address/offset in the bank
+   sensor_device_attribute_2->nr:      register offset, bitmask or NA. */
+static struct abituguru_data *abituguru_update_device(struct device *dev);
+
+static ssize_t show_bank1_value(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	return sprintf(buf, "%d\n", (data->bank1_value[attr->index] *
+		data->bank1_max_value[attr->index] + 128) / 255);
+}
+
+static ssize_t show_bank1_setting(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n",
+		(data->bank1_settings[attr->index][attr->nr] *
+		data->bank1_max_value[attr->index] + 128) / 255);
+}
+
+static ssize_t show_bank2_value(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	return sprintf(buf, "%d\n", (data->bank2_value[attr->index] *
+		ABIT_UGURU_FAN_MAX + 128) / 255);
+}
+
+static ssize_t show_bank2_setting(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n",
+		(data->bank2_settings[attr->index][attr->nr] *
+		ABIT_UGURU_FAN_MAX + 128) / 255);
+}
+
+static ssize_t store_bank1_setting(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 val = (simple_strtoul(buf, NULL, 10) * 255 +
+		data->bank1_max_value[attr->index]/2) /
+		data->bank1_max_value[attr->index];
+	ssize_t ret = count;
+
+	mutex_lock(&data->update_lock);
+	if (data->bank1_settings[attr->index][attr->nr] != val) {
+		u8 orig_val = data->bank1_settings[attr->index][attr->nr];
+		data->bank1_settings[attr->index][attr->nr] = val;
+		if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK1 + 2,
+				attr->index, data->bank1_settings[attr->index],
+				3) <= attr->nr) {
+			data->bank1_settings[attr->index][attr->nr] = orig_val;
+			ret = -EIO;
+		}
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t store_bank2_setting(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 val = (simple_strtoul(buf, NULL, 10)*255 + ABIT_UGURU_FAN_MAX/2) /
+		ABIT_UGURU_FAN_MAX;
+	ssize_t ret = count;
+
+	/* this check can be done before taking the lock */
+	if ((val < abituguru_bank2_min_threshold) ||
+			(val > abituguru_bank2_max_threshold))
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	if (data->bank2_settings[attr->index][attr->nr] != val) {
+		u8 orig_val = data->bank2_settings[attr->index][attr->nr];
+		data->bank2_settings[attr->index][attr->nr] = val;
+		if (abituguru_write(data, ABIT_UGURU_SENSOR_BANK2 + 2,
+				attr->index, data->bank2_settings[attr->index],
+				2) <= attr->nr) {
+			data->bank2_settings[attr->index][attr->nr] = orig_val;
+			ret = -EIO;
+		}
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_bank1_alarm(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	/* See if the alarm bit for this sensor is set, and if the
+	   alarm matches the type of alarm we're looking for (for volt
+	   it can be either low or high). The type is stored in a few
+	   readonly bits in the settings part of the relevant sensor.
+	   The bitmask of the type is passed to us in attr->nr. */
+	if ((data->alarms[attr->index / 8] & (0x01 << (attr->index % 8))) &&
+			(data->bank1_settings[attr->index][0] & attr->nr))
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_bank2_alarm(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = abituguru_update_device(dev);
+	if (!data)
+		return -EIO;
+	if (data->alarms[2] & (0x01 << attr->index))
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_bank1_mask(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	if (data->bank1_settings[attr->index][0] & attr->nr)
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t show_bank2_mask(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	if (data->bank2_settings[attr->index][0] & attr->nr)
+		return sprintf(buf, "1\n");
+	else
+		return sprintf(buf, "0\n");
+}
+
+static ssize_t store_bank1_mask(struct device *dev,
+	struct device_attribute *devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int mask = simple_strtoul(buf, NULL, 10);
+	ssize_t ret = count;
+	u8 orig_val;
+
+	mutex_lock(&data->update_lock);
+	orig_val = data->bank1_settings[attr->index][0];
+
+	if (mask)
+		data->bank1_settings[attr->index][0] |= attr->nr;
+	else
+		data->bank1_settings[attr->index][0] &= ~attr->nr;
+
+	if ((data->bank1_settings[attr->index][0] != orig_val) &&
+			(abituguru_write(data,
+			ABIT_UGURU_SENSOR_BANK1 + 2, attr->index,
+			data->bank1_settings[attr->index], 3) < 1)) {
+		data->bank1_settings[attr->index][0] = orig_val;
+		ret = -EIO;
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t store_bank2_mask(struct device *dev,
+	struct device_attribute *devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int mask = simple_strtoul(buf, NULL, 10);
+	ssize_t ret = count;
+	u8 orig_val;
+
+	mutex_lock(&data->update_lock);
+	orig_val = data->bank2_settings[attr->index][0];
+
+	if (mask)
+		data->bank2_settings[attr->index][0] |= attr->nr;
+	else
+		data->bank2_settings[attr->index][0] &= ~attr->nr;
+
+	if ((data->bank2_settings[attr->index][0] != orig_val) &&
+			(abituguru_write(data,
+			ABIT_UGURU_SENSOR_BANK2 + 2, attr->index,
+			data->bank2_settings[attr->index], 2) < 1)) {
+		data->bank2_settings[attr->index][0] = orig_val;
+		ret = -EIO;
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+/* Fan PWM (speed control) */
+static ssize_t show_pwm_setting(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	return sprintf(buf, "%d\n", data->pwm_settings[attr->index][attr->nr] *
+		abituguru_pwm_settings_multiplier[attr->nr]);
+}
+
+static ssize_t store_pwm_setting(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 min, val = (simple_strtoul(buf, NULL, 10) +
+		abituguru_pwm_settings_multiplier[attr->nr]/2) /
+		abituguru_pwm_settings_multiplier[attr->nr];
+	ssize_t ret = count;
+
+	/* special case pwm1 min pwm% */
+	if ((attr->index == 0) && ((attr->nr == 1) || (attr->nr == 2)))
+		min = 77;
+	else
+		min = abituguru_pwm_min[attr->nr];
+
+	/* this check can be done before taking the lock */
+	if ((val < min) || (val > abituguru_pwm_max[attr->nr]))
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	/* this check needs to be done after taking the lock */
+	if ((attr->nr & 1) &&
+			(val >= data->pwm_settings[attr->index][attr->nr + 1]))
+		ret = -EINVAL;
+	else if (!(attr->nr & 1) &&
+			(val <= data->pwm_settings[attr->index][attr->nr - 1]))
+		ret = -EINVAL;
+	else if (data->pwm_settings[attr->index][attr->nr] != val) {
+		u8 orig_val = data->pwm_settings[attr->index][attr->nr];
+		data->pwm_settings[attr->index][attr->nr] = val;
+		if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
+				attr->index, data->pwm_settings[attr->index],
+				5) <= attr->nr) {
+			data->pwm_settings[attr->index][attr->nr] =
+				orig_val;
+			ret = -EIO;
+		}
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_pwm_sensor(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int i;
+	/* We need to walk to the temp sensor addresses to find what
+	   the userspace id of the configured temp sensor is. */
+	for (i = 0; i < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]; i++)
+		if (data->bank1_address[ABIT_UGURU_TEMP_SENSOR][i] ==
+				(data->pwm_settings[attr->index][0] & 0x0F))
+			return sprintf(buf, "%d\n", i+1);
+
+	return -ENXIO;
+}
+
+static ssize_t store_pwm_sensor(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	unsigned long val = simple_strtoul(buf, NULL, 10) - 1;
+	ssize_t ret = count;
+
+	mutex_lock(&data->update_lock);
+	if (val < data->bank1_sensors[ABIT_UGURU_TEMP_SENSOR]) {
+		u8 orig_val = data->pwm_settings[attr->index][0];
+		u8 address = data->bank1_address[ABIT_UGURU_TEMP_SENSOR][val];
+		data->pwm_settings[attr->index][0] &= 0xF0;
+		data->pwm_settings[attr->index][0] |= address;
+		if (data->pwm_settings[attr->index][0] != orig_val) {
+			if (abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
+					attr->index,
+					data->pwm_settings[attr->index],
+					5) < 1) {
+				data->pwm_settings[attr->index][0] = orig_val;
+				ret = -EIO;
+			}
+		}
+	}
+	else
+		ret = -EINVAL;
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_pwm_enable(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	int res = 0;
+	if (data->pwm_settings[attr->index][0] & ABIT_UGURU_FAN_PWM_ENABLE)
+		res = 2;
+	return sprintf(buf, "%d\n", res);
+}
+
+static ssize_t store_pwm_enable(struct device *dev, struct device_attribute
+	*devattr, const char *buf, size_t count)
+{
+	struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr);
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	u8 orig_val, user_val = simple_strtoul(buf, NULL, 10);
+	ssize_t ret = count;
+
+	mutex_lock(&data->update_lock);
+	orig_val = data->pwm_settings[attr->index][0];
+	switch (user_val) {
+		case 0:
+			data->pwm_settings[attr->index][0] &=
+				~ABIT_UGURU_FAN_PWM_ENABLE;
+			break;
+		case 2:
+			data->pwm_settings[attr->index][0] |=
+				ABIT_UGURU_FAN_PWM_ENABLE;
+			break;
+		default:
+			ret = -EINVAL;
+	}
+	if ((data->pwm_settings[attr->index][0] != orig_val) &&
+			(abituguru_write(data, ABIT_UGURU_FAN_PWM + 1,
+			attr->index, data->pwm_settings[attr->index],
+			5) < 1)) {
+		data->pwm_settings[attr->index][0] = orig_val;
+		ret = -EIO;
+	}
+	mutex_unlock(&data->update_lock);
+	return ret;
+}
+
+static ssize_t show_name(struct device *dev,
+	struct device_attribute *devattr, char *buf)
+{
+	return sprintf(buf, "%s\n", ABIT_UGURU_NAME);
+}
+
+/* Sysfs attr templates, the real entries are generated automatically. */
+static const
+struct sensor_device_attribute_2 abituguru_sysfs_bank1_templ[2][9] = {
+	{
+	SENSOR_ATTR_2(in%d_input, 0444, show_bank1_value, NULL, 0, 0),
+	SENSOR_ATTR_2(in%d_min, 0644, show_bank1_setting,
+		store_bank1_setting, 1, 0),
+	SENSOR_ATTR_2(in%d_min_alarm, 0444, show_bank1_alarm, NULL,
+		ABIT_UGURU_VOLT_LOW_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(in%d_max, 0644, show_bank1_setting,
+		store_bank1_setting, 2, 0),
+	SENSOR_ATTR_2(in%d_max_alarm, 0444, show_bank1_alarm, NULL,
+		ABIT_UGURU_VOLT_HIGH_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(in%d_beep, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_shutdown, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_min_alarm_enable, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_VOLT_LOW_ALARM_ENABLE, 0),
+	SENSOR_ATTR_2(in%d_max_alarm_enable, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_VOLT_HIGH_ALARM_ENABLE, 0),
+	}, {
+	SENSOR_ATTR_2(temp%d_input, 0444, show_bank1_value, NULL, 0, 0),
+	SENSOR_ATTR_2(temp%d_alarm, 0444, show_bank1_alarm, NULL,
+		ABIT_UGURU_TEMP_HIGH_ALARM_FLAG, 0),
+	SENSOR_ATTR_2(temp%d_max, 0644, show_bank1_setting,
+		store_bank1_setting, 1, 0),
+	SENSOR_ATTR_2(temp%d_crit, 0644, show_bank1_setting,
+		store_bank1_setting, 2, 0),
+	SENSOR_ATTR_2(temp%d_beep, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_shutdown, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(temp%d_alarm_enable, 0644, show_bank1_mask,
+		store_bank1_mask, ABIT_UGURU_TEMP_HIGH_ALARM_ENABLE, 0),
+	}
+};
+
+static const struct sensor_device_attribute_2 abituguru_sysfs_fan_templ[6] = {
+	SENSOR_ATTR_2(fan%d_input, 0444, show_bank2_value, NULL, 0, 0),
+	SENSOR_ATTR_2(fan%d_alarm, 0444, show_bank2_alarm, NULL, 0, 0),
+	SENSOR_ATTR_2(fan%d_min, 0644, show_bank2_setting,
+		store_bank2_setting, 1, 0),
+	SENSOR_ATTR_2(fan%d_beep, 0644, show_bank2_mask,
+		store_bank2_mask, ABIT_UGURU_BEEP_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_shutdown, 0644, show_bank2_mask,
+		store_bank2_mask, ABIT_UGURU_SHUTDOWN_ENABLE, 0),
+	SENSOR_ATTR_2(fan%d_alarm_enable, 0644, show_bank2_mask,
+		store_bank2_mask, ABIT_UGURU_FAN_LOW_ALARM_ENABLE, 0),
+};
+
+static const struct sensor_device_attribute_2 abituguru_sysfs_pwm_templ[6] = {
+	SENSOR_ATTR_2(pwm%d_enable, 0644, show_pwm_enable,
+		store_pwm_enable, 0, 0),
+	SENSOR_ATTR_2(pwm%d_auto_channels_temp, 0644, show_pwm_sensor,
+		store_pwm_sensor, 0, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point1_pwm, 0644, show_pwm_setting,
+		store_pwm_setting, 1, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point2_pwm, 0644, show_pwm_setting,
+		store_pwm_setting, 2, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point1_temp, 0644, show_pwm_setting,
+		store_pwm_setting, 3, 0),
+	SENSOR_ATTR_2(pwm%d_auto_point2_temp, 0644, show_pwm_setting,
+		store_pwm_setting, 4, 0),
+};
+
+static struct sensor_device_attribute_2 abituguru_sysfs_attr[] = {
+	SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0),
+};
+
+static int __devinit abituguru_probe(struct platform_device *pdev)
+{
+	struct abituguru_data *data;
+	int i, j, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV;
+	char *sysfs_filename;
+
+	/* El weirdo probe order, to keep the sysfs order identical to the
+	   BIOS and window-appliction listing order. */
+	const u8 probe_order[ABIT_UGURU_MAX_BANK1_SENSORS] = {
+		0x00, 0x01, 0x03, 0x04, 0x0A, 0x08, 0x0E, 0x02,
+		0x09, 0x06, 0x05, 0x0B, 0x0F, 0x0D, 0x07, 0x0C };
+
+	if (!(data = kzalloc(sizeof(struct abituguru_data), GFP_KERNEL)))
+		return -ENOMEM;
+
+	data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start;
+	mutex_init(&data->update_lock);
+	platform_set_drvdata(pdev, data);
+
+	/* See if the uGuru is ready */
+	if (inb_p(data->addr + ABIT_UGURU_DATA) == ABIT_UGURU_STATUS_INPUT)
+		data->uguru_ready = 1;
+
+	/* Completely read the uGuru this has 2 purposes:
+	   - testread / see if one really is there.
+	   - make an in memory copy of all the uguru settings for future use. */
+	if (abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
+			data->alarms, 3, ABIT_UGURU_MAX_RETRIES) != 3)
+		goto abituguru_probe_error;
+
+	for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1, i,
+				&data->bank1_value[i], 1,
+				ABIT_UGURU_MAX_RETRIES) != 1)
+			goto abituguru_probe_error;
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK1+1, i,
+				data->bank1_settings[i], 3,
+				ABIT_UGURU_MAX_RETRIES) != 3)
+			goto abituguru_probe_error;
+	}
+	/* Note: We don't know how many bank2 sensors / pwms there really are,
+	   but in order to "detect" this we need to read the maximum amount
+	   anyways. If we read sensors/pwms not there we'll just read crap
+	   this can't hurt. We need the detection because we don't want
+	   unwanted writes, which will hurt! */
+	for (i = 0; i < ABIT_UGURU_MAX_BANK2_SENSORS; i++) {
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2, i,
+				&data->bank2_value[i], 1,
+				ABIT_UGURU_MAX_RETRIES) != 1)
+			goto abituguru_probe_error;
+		if (abituguru_read(data, ABIT_UGURU_SENSOR_BANK2+1, i,
+				data->bank2_settings[i], 2,
+				ABIT_UGURU_MAX_RETRIES) != 2)
+			goto abituguru_probe_error;
+	}
+	for (i = 0; i < ABIT_UGURU_MAX_PWMS; i++) {
+		if (abituguru_read(data, ABIT_UGURU_FAN_PWM, i,
+				data->pwm_settings[i], 5,
+				ABIT_UGURU_MAX_RETRIES) != 5)
+			goto abituguru_probe_error;
+	}
+	data->last_updated = jiffies;
+
+	/* Detect sensor types and fill the sysfs attr for bank1 */
+	sysfs_attr_i = 0;
+	sysfs_filename = data->sysfs_names;
+	sysfs_names_free = ABITUGURU_SYSFS_NAMES_LENGTH;
+	for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
+		res = abituguru_detect_bank1_sensor_type(data, probe_order[i]);
+		if (res < 0)
+			goto abituguru_probe_error;
+		if (res == ABIT_UGURU_NC)
+			continue;
+
+		/* res 1 (temp) sensors have 7 sysfs entries, 0 (in) 9 */
+		for (j = 0; j < (res ? 7 : 9); j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru_sysfs_bank1_templ[res][j].dev_attr.
+				attr.name, data->bank1_sensors[res] + res)
+				+ 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru_sysfs_bank1_templ[res][j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = probe_order[i];
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+		data->bank1_max_value[probe_order[i]] =
+			abituguru_bank1_max_value[res];
+		data->bank1_address[res][data->bank1_sensors[res]] =
+			probe_order[i];
+		data->bank1_sensors[res]++;
+	}
+	/* Detect number of sensors and fill the sysfs attr for bank2 (fans) */
+	abituguru_detect_no_bank2_sensors(data);
+	for (i = 0; i < data->bank2_sensors; i++) {
+		for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_fan_templ); j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru_sysfs_fan_templ[j].dev_attr.attr.name,
+				i + 1) + 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru_sysfs_fan_templ[j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = i;
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+	}
+	/* Detect number of sensors and fill the sysfs attr for pwms */
+	abituguru_detect_no_pwms(data);
+	for (i = 0; i < data->pwms; i++) {
+		for (j = 0; j < ARRAY_SIZE(abituguru_sysfs_pwm_templ); j++) {
+			used = snprintf(sysfs_filename, sysfs_names_free,
+				abituguru_sysfs_pwm_templ[j].dev_attr.attr.name,
+				i + 1) + 1;
+			data->sysfs_attr[sysfs_attr_i] =
+				abituguru_sysfs_pwm_templ[j];
+			data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name =
+				sysfs_filename;
+			data->sysfs_attr[sysfs_attr_i].index = i;
+			sysfs_filename += used;
+			sysfs_names_free -= used;
+			sysfs_attr_i++;
+		}
+	}
+	/* Fail safe check, this should never happen! */
+	if (sysfs_names_free < 0) {
+		printk(KERN_ERR ABIT_UGURU_NAME ": Fatal error ran out of "
+		       "space for sysfs attr names. This should never "
+		       "happen please report to the abituguru maintainer "
+		       "(see MAINTAINERS)\n");
+		res = -ENAMETOOLONG;
+		goto abituguru_probe_error;
+	}
+	printk(KERN_INFO ABIT_UGURU_NAME ": found Abit uGuru\n");
+
+	/* Register sysfs hooks */
+	data->class_dev = hwmon_device_register(&pdev->dev);
+	if (IS_ERR(data->class_dev)) {
+		res = PTR_ERR(data->class_dev);
+		goto abituguru_probe_error;
+	}
+	for (i = 0; i < sysfs_attr_i; i++)
+		device_create_file(&pdev->dev, &data->sysfs_attr[i].dev_attr);
+	for (i = 0; i < ARRAY_SIZE(abituguru_sysfs_attr); i++)
+		device_create_file(&pdev->dev,
+			&abituguru_sysfs_attr[i].dev_attr);
+
+	return 0;
+
+abituguru_probe_error:
+	kfree(data);
+	return res;
+}
+
+static int __devexit abituguru_remove(struct platform_device *pdev)
+{
+	struct abituguru_data *data = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+	hwmon_device_unregister(data->class_dev);
+	kfree(data);
+
+	return 0;
+}
+
+static struct abituguru_data *abituguru_update_device(struct device *dev)
+{
+	int i, err;
+	struct abituguru_data *data = dev_get_drvdata(dev);
+	/* fake a complete successful read if no update necessary. */
+	char success = 1;
+
+	mutex_lock(&data->update_lock);
+	if (time_after(jiffies, data->last_updated + HZ)) {
+		success = 0;
+		if ((err = abituguru_read(data, ABIT_UGURU_ALARM_BANK, 0,
+				data->alarms, 3, 0)) != 3)
+			goto LEAVE_UPDATE;
+		for (i = 0; i < ABIT_UGURU_MAX_BANK1_SENSORS; i++) {
+			if ((err = abituguru_read(data,
+					ABIT_UGURU_SENSOR_BANK1, i,
+					&data->bank1_value[i], 1, 0)) != 1)
+				goto LEAVE_UPDATE;
+			if ((err = abituguru_read(data,
+					ABIT_UGURU_SENSOR_BANK1 + 1, i,
+					data->bank1_settings[i], 3, 0)) != 3)
+				goto LEAVE_UPDATE;
+		}
+		for (i = 0; i < data->bank2_sensors; i++)
+			if ((err = abituguru_read(data,
+					ABIT_UGURU_SENSOR_BANK2, i,
+					&data->bank2_value[i], 1, 0)) != 1)
+				goto LEAVE_UPDATE;
+		/* success! */
+		success = 1;
+		data->update_timeouts = 0;
+LEAVE_UPDATE:
+		/* handle timeout condition */
+		if (err == -EBUSY) {
+			/* No overflow please */
+			if (data->update_timeouts < 255u)
+				data->update_timeouts++;
+			if (data->update_timeouts <= ABIT_UGURU_MAX_TIMEOUTS) {
+				ABIT_UGURU_DEBUG(3, "timeout exceeded, will "
+					"try again next update\n");
+				/* Just a timeout, fake a successful read */
+				success = 1;
+			} else
+				ABIT_UGURU_DEBUG(1, "timeout exceeded %d "
+					"times waiting for more input state\n",
+					(int)data->update_timeouts);
+		}
+		/* On success set last_updated */
+		if (success)
+			data->last_updated = jiffies;
+	}
+	mutex_unlock(&data->update_lock);
+
+	if (success)
+		return data;
+	else
+		return NULL;
+}
+
+static struct platform_driver abituguru_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= ABIT_UGURU_NAME,
+	},
+	.probe	= abituguru_probe,
+	.remove	= __devexit_p(abituguru_remove),
+};
+
+static int __init abituguru_detect(void)
+{
+	/* See if there is an uguru there. After a reboot uGuru will hold 0x00
+	   at DATA and 0xAC, when this driver has already been loaded once
+	   DATA will hold 0x08. For most uGuru's CMD will hold 0xAC in either
+	   scenario but some will hold 0x00.
+	   Some uGuru's initally hold 0x09 at DATA and will only hold 0x08
+	   after reading CMD first, so CMD must be read first! */
+	u8 cmd_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_CMD);
+	u8 data_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_DATA);
+	if (((data_val == 0x00) || (data_val == 0x08)) &&
+	    ((cmd_val == 0x00) || (cmd_val == 0xAC)))
+		return ABIT_UGURU_BASE;
+
+	ABIT_UGURU_DEBUG(2, "no Abit uGuru found, data = 0x%02X, cmd = "
+		"0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val);
+
+	if (force) {
+		printk(KERN_INFO ABIT_UGURU_NAME ": Assuming Abit uGuru is "
+				"present because of \"force\" parameter\n");
+		return ABIT_UGURU_BASE;
+	}
+
+	/* No uGuru found */
+	return -ENODEV;
+}
+
+static struct platform_device *abituguru_pdev;
+
+static int __init abituguru_init(void)
+{
+	int address, err;
+	struct resource res = { .flags = IORESOURCE_IO };
+
+	address = abituguru_detect();
+	if (address < 0)
+		return address;
+
+	err = platform_driver_register(&abituguru_driver);
+	if (err)
+		goto exit;
+
+	abituguru_pdev = platform_device_alloc(ABIT_UGURU_NAME, address);
+	if (!abituguru_pdev) {
+		printk(KERN_ERR ABIT_UGURU_NAME
+			": Device allocation failed\n");
+		err = -ENOMEM;
+		goto exit_driver_unregister;
+	}
+
+	res.start = address;
+	res.end = address + ABIT_UGURU_REGION_LENGTH - 1;
+	res.name = ABIT_UGURU_NAME;
+
+	err = platform_device_add_resources(abituguru_pdev, &res, 1);
+	if (err) {
+		printk(KERN_ERR ABIT_UGURU_NAME
+			": Device resource addition failed (%d)\n", err);
+		goto exit_device_put;
+	}
+
+	err = platform_device_add(abituguru_pdev);
+	if (err) {
+		printk(KERN_ERR ABIT_UGURU_NAME
+			": Device addition failed (%d)\n", err);
+		goto exit_device_put;
+	}
+
+	return 0;
+
+exit_device_put:
+	platform_device_put(abituguru_pdev);
+exit_driver_unregister:
+	platform_driver_unregister(&abituguru_driver);
+exit:
+	return err;
+}
+
+static void __exit abituguru_exit(void)
+{
+	platform_device_unregister(abituguru_pdev);
+	platform_driver_unregister(&abituguru_driver);
+}
+
+MODULE_AUTHOR("Hans de Goede <j.w.r.degoede@hhs.nl>");
+MODULE_DESCRIPTION("Abit uGuru Sensor device");
+MODULE_LICENSE("GPL");
+
+module_init(abituguru_init);
+module_exit(abituguru_exit);