Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 - new driver for eGalaxTouch serial touchscreen
 - new driver for TS-4800 touchscreen
 - an update for Goodix touchscreen driver
 - PS/2 mouse module was reworked to limit number of protocols we try on
   pass-through ports to speed up their detection time
 - wacom_w8001 touchscreen driver now reports pen and touch via separate
   instances of input devices
 - other driver changes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
  Input: elantech - mark protocols v2 and v3 as semi-mt
  Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
  Input: gpio-keys - fix check for disabling unsupported keys
  Input: omap-keypad - remove dead check
  Input: ti_am335x_tsc - fix HWPEN interrupt handling
  Input: omap-keypad - set tasklet data earlier
  Input: rohm_bu21023 - fix handling of retrying firmware update
  Input: ALPS - report v3 pinnacle trackstick device only if is present
  Input: ALPS - detect trackstick presence for v7 protocol
  Input: pcap_ts - use to_delayed_work
  Input: bma150 - constify bma150_cfg structure
  Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
  Input: egalax_ts_serial - fix potential NULL dereference on error
  Input: uinput - sanity check on ff_effects_max and EV_FF
  Input: uinput - rework ABS validation
  Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
  Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
  Input: goodix - add axis swapping and axis inversion support
  Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
  Input: goodix - add power management support
  ...

10 files changed, 1162 insertions, 162 deletions

diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
index ae33da7ab51f..53a97b379c9f 100644
--- a/drivers/input/touchscreen/Kconfig
+++ b/drivers/input/touchscreen/Kconfig
@@ -295,6 +295,16 @@ config TOUCHSCREEN_EGALAX
 	  To compile this driver as a module, choose M here: the
 	  module will be called egalax_ts.
 
+config TOUCHSCREEN_EGALAX_SERIAL
+	tristate "EETI eGalax serial touchscreen"
+	select SERIO
+	help
+	  Say Y here to enable support for serial connected EETI
+	  eGalax touch panels.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called egalax_ts_serial.
+
 config TOUCHSCREEN_FT6236
 	tristate "FT6236 I2C touchscreen"
 	depends on I2C
@@ -324,6 +334,7 @@ config TOUCHSCREEN_FUJITSU
 config TOUCHSCREEN_GOODIX
 	tristate "Goodix I2C touchscreen"
 	depends on I2C
+	depends on GPIOLIB
 	help
 	  Say Y here if you have the Goodix touchscreen (such as one
 	  installed in Onda v975w tablets) connected to your
@@ -927,6 +938,22 @@ config TOUCHSCREEN_TOUCHIT213
 	  To compile this driver as a module, choose M here: the
 	  module will be called touchit213.
 
+config TOUCHSCREEN_TS4800
+	tristate "TS-4800 touchscreen"
+	depends on HAS_IOMEM && OF
+	select MFD_SYSCON
+	select INPUT_POLLDEV
+	help
+	  Say Y here if you have a touchscreen on a TS-4800 board.
+
+	  On TS-4800, the touchscreen is not handled directly by Linux but by
+	  a companion FPGA.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ts4800_ts.
+
 config TOUCHSCREEN_TSC_SERIO
 	tristate "TSC-10/25/40 serial touchscreen support"
 	select SERIO
diff --git a/drivers/input/touchscreen/Makefile b/drivers/input/touchscreen/Makefile
index cbaa6abb08da..968ff12e3132 100644
--- a/drivers/input/touchscreen/Makefile
+++ b/drivers/input/touchscreen/Makefile
@@ -35,6 +35,7 @@ obj-$(CONFIG_TOUCHSCREEN_EETI)		+= eeti_ts.o
 obj-$(CONFIG_TOUCHSCREEN_ELAN)		+= elants_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ELO)		+= elo.o
 obj-$(CONFIG_TOUCHSCREEN_EGALAX)	+= egalax_ts.o
+obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL)	+= egalax_ts_serial.o
 obj-$(CONFIG_TOUCHSCREEN_FT6236)	+= ft6236.o
 obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
 obj-$(CONFIG_TOUCHSCREEN_GOODIX)	+= goodix.o
@@ -68,6 +69,7 @@ obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC)	+= ti_am335x_tsc.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
+obj-$(CONFIG_TOUCHSCREEN_TS4800)	+= ts4800-ts.o
 obj-$(CONFIG_TOUCHSCREEN_TSC_SERIO)	+= tsc40.o
 obj-$(CONFIG_TOUCHSCREEN_TSC200X_CORE)	+= tsc200x-core.o
 obj-$(CONFIG_TOUCHSCREEN_TSC2004)	+= tsc2004.o
diff --git a/drivers/input/touchscreen/egalax_ts_serial.c b/drivers/input/touchscreen/egalax_ts_serial.c
new file mode 100644
index 000000000000..657bbae608c8
--- /dev/null
+++ b/drivers/input/touchscreen/egalax_ts_serial.c
@@ -0,0 +1,194 @@
+/*
+ * EETI Egalax serial touchscreen driver
+ *
+ * Copyright (c) 2015 Zoltán Böszörményi <zboszor@pr.hu>
+ *
+ * based on the
+ *
+ * Hampshire serial touchscreen driver (Copyright (c) 2010 Adam Bennett)
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/serio.h>
+
+#define DRIVER_DESC	"EETI Egalax serial touchscreen driver"
+
+/*
+ * Definitions & global arrays.
+ */
+
+#define EGALAX_FORMAT_MAX_LENGTH	6
+#define EGALAX_FORMAT_START_BIT		BIT(7)
+#define EGALAX_FORMAT_PRESSURE_BIT	BIT(6)
+#define EGALAX_FORMAT_TOUCH_BIT		BIT(0)
+#define EGALAX_FORMAT_RESOLUTION_MASK	0x06
+
+#define EGALAX_MIN_XC			0
+#define EGALAX_MAX_XC			0x4000
+#define EGALAX_MIN_YC			0
+#define EGALAX_MAX_YC			0x4000
+
+/*
+ * Per-touchscreen data.
+ */
+struct egalax {
+	struct input_dev *input;
+	struct serio *serio;
+	int idx;
+	u8 data[EGALAX_FORMAT_MAX_LENGTH];
+	char phys[32];
+};
+
+static void egalax_process_data(struct egalax *egalax)
+{
+	struct input_dev *dev = egalax->input;
+	u8 *data = egalax->data;
+	u16 x, y;
+	u8 shift;
+	u8 mask;
+
+	shift = 3 - ((data[0] & EGALAX_FORMAT_RESOLUTION_MASK) >> 1);
+	mask = 0xff >> (shift + 1);
+
+	x = (((u16)(data[1] & mask) << 7) | (data[2] & 0x7f)) << shift;
+	y = (((u16)(data[3] & mask) << 7) | (data[4] & 0x7f)) << shift;
+
+	input_report_key(dev, BTN_TOUCH, data[0] & EGALAX_FORMAT_TOUCH_BIT);
+	input_report_abs(dev, ABS_X, x);
+	input_report_abs(dev, ABS_Y, y);
+	input_sync(dev);
+}
+
+static irqreturn_t egalax_interrupt(struct serio *serio,
+				    unsigned char data, unsigned int flags)
+{
+	struct egalax *egalax = serio_get_drvdata(serio);
+	int pkt_len;
+
+	egalax->data[egalax->idx++] = data;
+
+	if (likely(egalax->data[0] & EGALAX_FORMAT_START_BIT)) {
+		pkt_len = egalax->data[0] & EGALAX_FORMAT_PRESSURE_BIT ? 6 : 5;
+		if (pkt_len == egalax->idx) {
+			egalax_process_data(egalax);
+			egalax->idx = 0;
+		}
+	} else {
+		dev_dbg(&serio->dev, "unknown/unsynchronized data: %x\n",
+			egalax->data[0]);
+		egalax->idx = 0;
+	}
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * egalax_connect() is the routine that is called when someone adds a
+ * new serio device that supports egalax protocol and registers it as
+ * an input device. This is usually accomplished using inputattach.
+ */
+static int egalax_connect(struct serio *serio, struct serio_driver *drv)
+{
+	struct egalax *egalax;
+	struct input_dev *input_dev;
+	int error;
+
+	egalax = kzalloc(sizeof(struct egalax), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!egalax || !input_dev) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	egalax->serio = serio;
+	egalax->input = input_dev;
+	snprintf(egalax->phys, sizeof(egalax->phys),
+		 "%s/input0", serio->phys);
+
+	input_dev->name = "EETI eGalaxTouch Serial TouchScreen";
+	input_dev->phys = egalax->phys;
+	input_dev->id.bustype = BUS_RS232;
+	input_dev->id.vendor = SERIO_EGALAX;
+	input_dev->id.product = 0;
+	input_dev->id.version = 0x0001;
+	input_dev->dev.parent = &serio->dev;
+
+	input_set_capability(input_dev, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(input_dev, ABS_X,
+			     EGALAX_MIN_XC, EGALAX_MAX_XC, 0, 0);
+	input_set_abs_params(input_dev, ABS_Y,
+			     EGALAX_MIN_YC, EGALAX_MAX_YC, 0, 0);
+
+	serio_set_drvdata(serio, egalax);
+
+	error = serio_open(serio, drv);
+	if (error)
+		goto err_reset_drvdata;
+
+	error = input_register_device(input_dev);
+	if (error)
+		goto err_close_serio;
+
+	return 0;
+
+err_close_serio:
+	serio_close(serio);
+err_reset_drvdata:
+	serio_set_drvdata(serio, NULL);
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(egalax);
+	return error;
+}
+
+static void egalax_disconnect(struct serio *serio)
+{
+	struct egalax *egalax = serio_get_drvdata(serio);
+
+	serio_close(serio);
+	serio_set_drvdata(serio, NULL);
+	input_unregister_device(egalax->input);
+	kfree(egalax);
+}
+
+/*
+ * The serio driver structure.
+ */
+
+static const struct serio_device_id egalax_serio_ids[] = {
+	{
+		.type	= SERIO_RS232,
+		.proto	= SERIO_EGALAX,
+		.id	= SERIO_ANY,
+		.extra	= SERIO_ANY,
+	},
+	{ 0 }
+};
+
+MODULE_DEVICE_TABLE(serio, egalax_serio_ids);
+
+static struct serio_driver egalax_drv = {
+	.driver		= {
+		.name	= "egalax",
+	},
+	.description	= DRIVER_DESC,
+	.id_table	= egalax_serio_ids,
+	.interrupt	= egalax_interrupt,
+	.connect	= egalax_connect,
+	.disconnect	= egalax_disconnect,
+};
+module_serio_driver(egalax_drv);
+
+MODULE_AUTHOR("Zoltán Böszörményi <zboszor@pr.hu>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/input/touchscreen/goodix.c b/drivers/input/touchscreen/goodix.c
index 4d113c9e4b77..240b16f3ee97 100644
--- a/drivers/input/touchscreen/goodix.c
+++ b/drivers/input/touchscreen/goodix.c
@@ -2,6 +2,7 @@
  *  Driver for Goodix Touchscreens
  *
  *  Copyright (c) 2014 Red Hat Inc.
+ *  Copyright (c) 2015 K. Merker <merker@debian.org>
  *
  *  This code is based on gt9xx.c authored by andrew@goodix.com:
  *
@@ -16,6 +17,8 @@
 
 #include <linux/kernel.h>
 #include <linux/dmi.h>
+#include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/input/mt.h>
@@ -33,11 +36,24 @@ struct goodix_ts_data {
 	struct input_dev *input_dev;
 	int abs_x_max;
 	int abs_y_max;
+	bool swapped_x_y;
+	bool inverted_x;
+	bool inverted_y;
 	unsigned int max_touch_num;
 	unsigned int int_trigger_type;
-	bool rotated_screen;
+	int cfg_len;
+	struct gpio_desc *gpiod_int;
+	struct gpio_desc *gpiod_rst;
+	u16 id;
+	u16 version;
+	const char *cfg_name;
+	struct completion firmware_loading_complete;
+	unsigned long irq_flags;
 };
 
+#define GOODIX_GPIO_INT_NAME		"irq"
+#define GOODIX_GPIO_RST_NAME		"reset"
+
 #define GOODIX_MAX_HEIGHT		4096
 #define GOODIX_MAX_WIDTH		4096
 #define GOODIX_INT_TRIGGER		1
@@ -45,8 +61,13 @@ struct goodix_ts_data {
 #define GOODIX_MAX_CONTACTS		10
 
 #define GOODIX_CONFIG_MAX_LENGTH	240
+#define GOODIX_CONFIG_911_LENGTH	186
+#define GOODIX_CONFIG_967_LENGTH	228
 
 /* Register defines */
+#define GOODIX_REG_COMMAND		0x8040
+#define GOODIX_CMD_SCREEN_OFF		0x05
+
 #define GOODIX_READ_COOR_ADDR		0x814E
 #define GOODIX_REG_CONFIG_DATA		0x8047
 #define GOODIX_REG_ID			0x8140
@@ -115,6 +136,63 @@ static int goodix_i2c_read(struct i2c_client *client,
 	return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
 }
 
+/**
+ * goodix_i2c_write - write data to a register of the i2c slave device.
+ *
+ * @client: i2c device.
+ * @reg: the register to write to.
+ * @buf: raw data buffer to write.
+ * @len: length of the buffer to write
+ */
+static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
+			    unsigned len)
+{
+	u8 *addr_buf;
+	struct i2c_msg msg;
+	int ret;
+
+	addr_buf = kmalloc(len + 2, GFP_KERNEL);
+	if (!addr_buf)
+		return -ENOMEM;
+
+	addr_buf[0] = reg >> 8;
+	addr_buf[1] = reg & 0xFF;
+	memcpy(&addr_buf[2], buf, len);
+
+	msg.flags = 0;
+	msg.addr = client->addr;
+	msg.buf = addr_buf;
+	msg.len = len + 2;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	kfree(addr_buf);
+	return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
+}
+
+static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
+{
+	return goodix_i2c_write(client, reg, &value, sizeof(value));
+}
+
+static int goodix_get_cfg_len(u16 id)
+{
+	switch (id) {
+	case 911:
+	case 9271:
+	case 9110:
+	case 927:
+	case 928:
+		return GOODIX_CONFIG_911_LENGTH;
+
+	case 912:
+	case 967:
+		return GOODIX_CONFIG_967_LENGTH;
+
+	default:
+		return GOODIX_CONFIG_MAX_LENGTH;
+	}
+}
+
 static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
 {
 	int touch_num;
@@ -155,10 +233,13 @@ static void goodix_ts_report_touch(struct goodix_ts_data *ts, u8 *coor_data)
 	int input_y = get_unaligned_le16(&coor_data[3]);
 	int input_w = get_unaligned_le16(&coor_data[5]);
 
-	if (ts->rotated_screen) {
+	/* Inversions have to happen before axis swapping */
+	if (ts->inverted_x)
 		input_x = ts->abs_x_max - input_x;
+	if (ts->inverted_y)
 		input_y = ts->abs_y_max - input_y;
-	}
+	if (ts->swapped_x_y)
+		swap(input_x, input_y);
 
 	input_mt_slot(ts->input_dev, id);
 	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
@@ -202,21 +283,195 @@ static void goodix_process_events(struct goodix_ts_data *ts)
  */
 static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 {
-	static const u8 end_cmd[] = {
-		GOODIX_READ_COOR_ADDR >> 8,
-		GOODIX_READ_COOR_ADDR & 0xff,
-		0
-	};
 	struct goodix_ts_data *ts = dev_id;
 
 	goodix_process_events(ts);
 
-	if (i2c_master_send(ts->client, end_cmd, sizeof(end_cmd)) < 0)
+	if (goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0) < 0)
 		dev_err(&ts->client->dev, "I2C write end_cmd error\n");
 
 	return IRQ_HANDLED;
 }
 
+static void goodix_free_irq(struct goodix_ts_data *ts)
+{
+	devm_free_irq(&ts->client->dev, ts->client->irq, ts);
+}
+
+static int goodix_request_irq(struct goodix_ts_data *ts)
+{
+	return devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+					 NULL, goodix_ts_irq_handler,
+					 ts->irq_flags, ts->client->name, ts);
+}
+
+/**
+ * goodix_check_cfg - Checks if config fw is valid
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: firmware config data
+ */
+static int goodix_check_cfg(struct goodix_ts_data *ts,
+			    const struct firmware *cfg)
+{
+	int i, raw_cfg_len;
+	u8 check_sum = 0;
+
+	if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
+		dev_err(&ts->client->dev,
+			"The length of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	raw_cfg_len = cfg->size - 2;
+	for (i = 0; i < raw_cfg_len; i++)
+		check_sum += cfg->data[i];
+	check_sum = (~check_sum) + 1;
+	if (check_sum != cfg->data[raw_cfg_len]) {
+		dev_err(&ts->client->dev,
+			"The checksum of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	if (cfg->data[raw_cfg_len + 1] != 1) {
+		dev_err(&ts->client->dev,
+			"Config fw must have Config_Fresh register set");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_send_cfg - Write fw config to device
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: config firmware to write to device
+ */
+static int goodix_send_cfg(struct goodix_ts_data *ts,
+			   const struct firmware *cfg)
+{
+	int error;
+
+	error = goodix_check_cfg(ts, cfg);
+	if (error)
+		return error;
+
+	error = goodix_i2c_write(ts->client, GOODIX_REG_CONFIG_DATA, cfg->data,
+				 cfg->size);
+	if (error) {
+		dev_err(&ts->client->dev, "Failed to write config data: %d",
+			error);
+		return error;
+	}
+	dev_dbg(&ts->client->dev, "Config sent successfully.");
+
+	/* Let the firmware reconfigure itself, so sleep for 10ms */
+	usleep_range(10000, 11000);
+
+	return 0;
+}
+
+static int goodix_int_sync(struct goodix_ts_data *ts)
+{
+	int error;
+
+	error = gpiod_direction_output(ts->gpiod_int, 0);
+	if (error)
+		return error;
+
+	msleep(50);				/* T5: 50ms */
+
+	error = gpiod_direction_input(ts->gpiod_int);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
+{
+	int error;
+
+	/* begin select I2C slave addr */
+	error = gpiod_direction_output(ts->gpiod_rst, 0);
+	if (error)
+		return error;
+
+	msleep(20);				/* T2: > 10ms */
+
+	/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
+	error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+	if (error)
+		return error;
+
+	usleep_range(100, 2000);		/* T3: > 100us */
+
+	error = gpiod_direction_output(ts->gpiod_rst, 1);
+	if (error)
+		return error;
+
+	usleep_range(6000, 10000);		/* T4: > 5ms */
+
+	/* end select I2C slave addr */
+	error = gpiod_direction_input(ts->gpiod_rst);
+	if (error)
+		return error;
+
+	error = goodix_int_sync(ts);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+/**
+ * goodix_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_get_gpio_config(struct goodix_ts_data *ts)
+{
+	int error;
+	struct device *dev;
+	struct gpio_desc *gpiod;
+
+	if (!ts->client)
+		return -EINVAL;
+	dev = &ts->client->dev;
+
+	/* Get the interrupt GPIO pin number */
+	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
+	if (IS_ERR(gpiod)) {
+		error = PTR_ERR(gpiod);
+		if (error != -EPROBE_DEFER)
+			dev_dbg(dev, "Failed to get %s GPIO: %d\n",
+				GOODIX_GPIO_INT_NAME, error);
+		return error;
+	}
+
+	ts->gpiod_int = gpiod;
+
+	/* Get the reset line GPIO pin number */
+	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN);
+	if (IS_ERR(gpiod)) {
+		error = PTR_ERR(gpiod);
+		if (error != -EPROBE_DEFER)
+			dev_dbg(dev, "Failed to get %s GPIO: %d\n",
+				GOODIX_GPIO_RST_NAME, error);
+		return error;
+	}
+
+	ts->gpiod_rst = gpiod;
+
+	return 0;
+}
+
 /**
  * goodix_read_config - Read the embedded configuration of the panel
  *
@@ -230,14 +485,15 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 	int error;
 
 	error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
-				config,
-				GOODIX_CONFIG_MAX_LENGTH);
+				config, ts->cfg_len);
 	if (error) {
 		dev_warn(&ts->client->dev,
 			 "Error reading config (%d), using defaults\n",
 			 error);
 		ts->abs_x_max = GOODIX_MAX_WIDTH;
 		ts->abs_y_max = GOODIX_MAX_HEIGHT;
+		if (ts->swapped_x_y)
+			swap(ts->abs_x_max, ts->abs_y_max);
 		ts->int_trigger_type = GOODIX_INT_TRIGGER;
 		ts->max_touch_num = GOODIX_MAX_CONTACTS;
 		return;
@@ -245,6 +501,8 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 
 	ts->abs_x_max = get_unaligned_le16(&config[RESOLUTION_LOC]);
 	ts->abs_y_max = get_unaligned_le16(&config[RESOLUTION_LOC + 2]);
+	if (ts->swapped_x_y)
+		swap(ts->abs_x_max, ts->abs_y_max);
 	ts->int_trigger_type = config[TRIGGER_LOC] & 0x03;
 	ts->max_touch_num = config[MAX_CONTACTS_LOC] & 0x0f;
 	if (!ts->abs_x_max || !ts->abs_y_max || !ts->max_touch_num) {
@@ -252,42 +510,45 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 			"Invalid config, using defaults\n");
 		ts->abs_x_max = GOODIX_MAX_WIDTH;
 		ts->abs_y_max = GOODIX_MAX_HEIGHT;
+		if (ts->swapped_x_y)
+			swap(ts->abs_x_max, ts->abs_y_max);
 		ts->max_touch_num = GOODIX_MAX_CONTACTS;
 	}
 
-	ts->rotated_screen = dmi_check_system(rotated_screen);
-	if (ts->rotated_screen)
+	if (dmi_check_system(rotated_screen)) {
+		ts->inverted_x = true;
+		ts->inverted_y = true;
 		dev_dbg(&ts->client->dev,
 			 "Applying '180 degrees rotated screen' quirk\n");
+	}
 }
 
 /**
  * goodix_read_version - Read goodix touchscreen version
  *
- * @client: the i2c client
- * @version: output buffer containing the version on success
- * @id: output buffer containing the id on success
+ * @ts: our goodix_ts_data pointer
  */
-static int goodix_read_version(struct i2c_client *client, u16 *version, u16 *id)
+static int goodix_read_version(struct goodix_ts_data *ts)
 {
 	int error;
 	u8 buf[6];
 	char id_str[5];
 
-	error = goodix_i2c_read(client, GOODIX_REG_ID, buf, sizeof(buf));
+	error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
 	if (error) {
-		dev_err(&client->dev, "read version failed: %d\n", error);
+		dev_err(&ts->client->dev, "read version failed: %d\n", error);
 		return error;
 	}
 
 	memcpy(id_str, buf, 4);
 	id_str[4] = 0;
-	if (kstrtou16(id_str, 10, id))
-		*id = 0x1001;
+	if (kstrtou16(id_str, 10, &ts->id))
+		ts->id = 0x1001;
 
-	*version = get_unaligned_le16(&buf[4]);
+	ts->version = get_unaligned_le16(&buf[4]);
 
-	dev_info(&client->dev, "ID %d, version: %04x\n", *id, *version);
+	dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id,
+		 ts->version);
 
 	return 0;
 }
@@ -321,13 +582,10 @@ static int goodix_i2c_test(struct i2c_client *client)
  * goodix_request_input_dev - Allocate, populate and register the input device
  *
  * @ts: our goodix_ts_data pointer
- * @version: device firmware version
- * @id: device ID
  *
  * Must be called during probe
  */
-static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
-				    u16 id)
+static int goodix_request_input_dev(struct goodix_ts_data *ts)
 {
 	int error;
 
@@ -351,8 +609,8 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	ts->input_dev->phys = "input/ts";
 	ts->input_dev->id.bustype = BUS_I2C;
 	ts->input_dev->id.vendor = 0x0416;
-	ts->input_dev->id.product = id;
-	ts->input_dev->id.version = version;
+	ts->input_dev->id.product = ts->id;
+	ts->input_dev->id.version = ts->version;
 
 	error = input_register_device(ts->input_dev);
 	if (error) {
@@ -364,13 +622,75 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	return 0;
 }
 
+/**
+ * goodix_configure_dev - Finish device initialization
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called from probe to finish initialization of the device.
+ * Contains the common initialization code for both devices that
+ * declare gpio pins and devices that do not. It is either called
+ * directly from probe or from request_firmware_wait callback.
+ */
+static int goodix_configure_dev(struct goodix_ts_data *ts)
+{
+	int error;
+
+	ts->swapped_x_y = device_property_read_bool(&ts->client->dev,
+						    "touchscreen-swapped-x-y");
+	ts->inverted_x = device_property_read_bool(&ts->client->dev,
+						   "touchscreen-inverted-x");
+	ts->inverted_y = device_property_read_bool(&ts->client->dev,
+						   "touchscreen-inverted-y");
+
+	goodix_read_config(ts);
+
+	error = goodix_request_input_dev(ts);
+	if (error)
+		return error;
+
+	ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+	error = goodix_request_irq(ts);
+	if (error) {
+		dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_config_cb - Callback to finish device init
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * request_firmware_wait callback that finishes
+ * initialization of the device.
+ */
+static void goodix_config_cb(const struct firmware *cfg, void *ctx)
+{
+	struct goodix_ts_data *ts = ctx;
+	int error;
+
+	if (cfg) {
+		/* send device configuration to the firmware */
+		error = goodix_send_cfg(ts, cfg);
+		if (error)
+			goto err_release_cfg;
+	}
+
+	goodix_configure_dev(ts);
+
+err_release_cfg:
+	release_firmware(cfg);
+	complete_all(&ts->firmware_loading_complete);
+}
+
 static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
 	struct goodix_ts_data *ts;
-	unsigned long irq_flags;
 	int error;
-	u16 version_info, id_info;
 
 	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
 
@@ -385,6 +705,20 @@ static int goodix_ts_probe(struct i2c_client *client,
 
 	ts->client = client;
 	i2c_set_clientdata(client, ts);
+	init_completion(&ts->firmware_loading_complete);
+
+	error = goodix_get_gpio_config(ts);
+	if (error)
+		return error;
+
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* reset the controller */
+		error = goodix_reset(ts);
+		if (error) {
+			dev_err(&client->dev, "Controller reset failed.\n");
+			return error;
+		}
+	}
 
 	error = goodix_i2c_test(client);
 	if (error) {
@@ -392,30 +726,125 @@ static int goodix_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
-	error = goodix_read_version(client, &version_info, &id_info);
+	error = goodix_read_version(ts);
 	if (error) {
 		dev_err(&client->dev, "Read version failed.\n");
 		return error;
 	}
 
-	goodix_read_config(ts);
+	ts->cfg_len = goodix_get_cfg_len(ts->id);
+
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* update device config */
+		ts->cfg_name = devm_kasprintf(&client->dev, GFP_KERNEL,
+					      "goodix_%d_cfg.bin", ts->id);
+		if (!ts->cfg_name)
+			return -ENOMEM;
+
+		error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
+						&client->dev, GFP_KERNEL, ts,
+						goodix_config_cb);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to invoke firmware loader: %d\n",
+				error);
+			return error;
+		}
 
-	error = goodix_request_input_dev(ts, version_info, id_info);
-	if (error)
-		return error;
+		return 0;
+	} else {
+		error = goodix_configure_dev(ts);
+		if (error)
+			return error;
+	}
+
+	return 0;
+}
+
+static int goodix_ts_remove(struct i2c_client *client)
+{
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+
+	if (ts->gpiod_int && ts->gpiod_rst)
+		wait_for_completion(&ts->firmware_loading_complete);
+
+	return 0;
+}
+
+static int __maybe_unused goodix_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+	int error;
 
-	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
-	error = devm_request_threaded_irq(&ts->client->dev, client->irq,
-					  NULL, goodix_ts_irq_handler,
-					  irq_flags, client->name, ts);
+	/* We need gpio pins to suspend/resume */
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	wait_for_completion(&ts->firmware_loading_complete);
+
+	/* Free IRQ as IRQ pin is used as output in the suspend sequence */
+	goodix_free_irq(ts);
+
+	/* Output LOW on the INT pin for 5 ms */
+	error = gpiod_direction_output(ts->gpiod_int, 0);
 	if (error) {
-		dev_err(&client->dev, "request IRQ failed: %d\n", error);
+		goodix_request_irq(ts);
 		return error;
 	}
 
+	usleep_range(5000, 6000);
+
+	error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND,
+				    GOODIX_CMD_SCREEN_OFF);
+	if (error) {
+		dev_err(&ts->client->dev, "Screen off command failed\n");
+		gpiod_direction_input(ts->gpiod_int);
+		goodix_request_irq(ts);
+		return -EAGAIN;
+	}
+
+	/*
+	 * The datasheet specifies that the interval between sending screen-off
+	 * command and wake-up should be longer than 58 ms. To avoid waking up
+	 * sooner, delay 58ms here.
+	 */
+	msleep(58);
+	return 0;
+}
+
+static int __maybe_unused goodix_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	/*
+	 * Exit sleep mode by outputting HIGH level to INT pin
+	 * for 2ms~5ms.
+	 */
+	error = gpiod_direction_output(ts->gpiod_int, 1);
+	if (error)
+		return error;
+
+	usleep_range(2000, 5000);
+
+	error = goodix_int_sync(ts);
+	if (error)
+		return error;
+
+	error = goodix_request_irq(ts);
+	if (error)
+		return error;
+
 	return 0;
 }
 
+static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
+
 static const struct i2c_device_id goodix_ts_id[] = {
 	{ "GDIX1001:00", 0 },
 	{ }
@@ -446,11 +875,13 @@ MODULE_DEVICE_TABLE(of, goodix_of_match);
 
 static struct i2c_driver goodix_ts_driver = {
 	.probe = goodix_ts_probe,
+	.remove = goodix_ts_remove,
 	.id_table = goodix_ts_id,
 	.driver = {
 		.name = "Goodix-TS",
 		.acpi_match_table = ACPI_PTR(goodix_acpi_match),
 		.of_match_table = of_match_ptr(goodix_of_match),
+		.pm = &goodix_pm_ops,
 	},
 };
 module_i2c_driver(goodix_ts_driver);
diff --git a/drivers/input/touchscreen/pcap_ts.c b/drivers/input/touchscreen/pcap_ts.c
index 23a354a392ae..0e3fc419a3cf 100644
--- a/drivers/input/touchscreen/pcap_ts.c
+++ b/drivers/input/touchscreen/pcap_ts.c
@@ -87,7 +87,7 @@ static void pcap_ts_read_xy(void *data, u16 res[2])
 
 static void pcap_ts_work(struct work_struct *work)
 {
-	struct delayed_work *dw = container_of(work, struct delayed_work, work);
+	struct delayed_work *dw = to_delayed_work(work);
 	struct pcap_ts *pcap_ts = container_of(dw, struct pcap_ts, work);
 	u8 ch[2];
 
diff --git a/drivers/input/touchscreen/pixcir_i2c_ts.c b/drivers/input/touchscreen/pixcir_i2c_ts.c
index 4b961ad9f0b5..09523a3d3f23 100644
--- a/drivers/input/touchscreen/pixcir_i2c_ts.c
+++ b/drivers/input/touchscreen/pixcir_i2c_ts.c
@@ -38,6 +38,8 @@ struct pixcir_i2c_ts_data {
 	struct input_dev *input;
 	struct gpio_desc *gpio_attb;
 	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_enable;
+	struct gpio_desc *gpio_wake;
 	const struct pixcir_i2c_chip_data *chip;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;
@@ -208,6 +210,11 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 	struct device *dev = &ts->client->dev;
 	int ret;
 
+	if (mode == PIXCIR_POWER_ACTIVE || mode == PIXCIR_POWER_IDLE) {
+		if (ts->gpio_wake)
+			gpiod_set_value_cansleep(ts->gpio_wake, 1);
+	}
+
 	ret = i2c_smbus_read_byte_data(ts->client, PIXCIR_REG_POWER_MODE);
 	if (ret < 0) {
 		dev_err(dev, "%s: can't read reg 0x%x : %d\n",
@@ -228,6 +235,11 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 		return ret;
 	}
 
+	if (mode == PIXCIR_POWER_HALT) {
+		if (ts->gpio_wake)
+			gpiod_set_value_cansleep(ts->gpio_wake, 0);
+	}
+
 	return 0;
 }
 
@@ -302,6 +314,11 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 	struct device *dev = &ts->client->dev;
 	int error;
 
+	if (ts->gpio_enable) {
+		gpiod_set_value_cansleep(ts->gpio_enable, 1);
+		msleep(100);
+	}
+
 	/* LEVEL_TOUCH interrupt with active low polarity */
 	error = pixcir_set_int_mode(ts, PIXCIR_INT_LEVEL_TOUCH, 0);
 	if (error) {
@@ -343,6 +360,9 @@ static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 	/* Wait till running ISR is complete */
 	synchronize_irq(ts->client->irq);
 
+	if (ts->gpio_enable)
+		gpiod_set_value_cansleep(ts->gpio_enable, 0);
+
 	return 0;
 }
 
@@ -534,6 +554,27 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+	tsdata->gpio_wake = devm_gpiod_get_optional(dev, "wake",
+						    GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_wake)) {
+		error = PTR_ERR(tsdata->gpio_wake);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get wake gpio: %d\n", error);
+		return error;
+	}
+
+	tsdata->gpio_enable = devm_gpiod_get_optional(dev, "enable",
+						      GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_enable)) {
+		error = PTR_ERR(tsdata->gpio_enable);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get enable gpio: %d\n", error);
+		return error;
+	}
+
+	if (tsdata->gpio_enable)
+		msleep(100);
+
 	error = devm_request_threaded_irq(dev, client->irq, NULL, pixcir_ts_isr,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 					  client->name, tsdata);
diff --git a/drivers/input/touchscreen/rohm_bu21023.c b/drivers/input/touchscreen/rohm_bu21023.c
index ba6024f93469..611156a2ef80 100644
--- a/drivers/input/touchscreen/rohm_bu21023.c
+++ b/drivers/input/touchscreen/rohm_bu21023.c
@@ -725,7 +725,7 @@ static int rohm_ts_load_firmware(struct i2c_client *client,
 			break;
 
 		error = -EIO;
-	} while (++retry >= FIRMWARE_RETRY_MAX);
+	} while (++retry <= FIRMWARE_RETRY_MAX);
 
 out:
 	error2 = i2c_smbus_write_byte_data(client, INT_MASK, INT_ALL);
diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 191a1b87895f..a21a07c3ab6d 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -273,8 +273,6 @@ static irqreturn_t titsc_irq(int irq, void *dev)
 	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
 	if (status & IRQENB_HW_PEN) {
 		ts_dev->pen_down = true;
-		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
-		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
 		irqclr |= IRQENB_HW_PEN;
 	}
 
diff --git a/drivers/input/touchscreen/ts4800-ts.c b/drivers/input/touchscreen/ts4800-ts.c
new file mode 100644
index 000000000000..3c3dd78303be
--- /dev/null
+++ b/drivers/input/touchscreen/ts4800-ts.c
@@ -0,0 +1,216 @@
+/*
+ * Touchscreen driver for the TS-4800 board
+ *
+ * Copyright (c) 2015 - Savoir-faire Linux
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/bitops.h>
+#include <linux/input.h>
+#include <linux/input-polldev.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* polling interval in ms */
+#define POLL_INTERVAL		3
+
+#define DEBOUNCE_COUNT		1
+
+/* sensor values are 12-bit wide */
+#define MAX_12BIT		((1 << 12) - 1)
+
+#define PENDOWN_MASK		0x1
+
+#define X_OFFSET		0x0
+#define Y_OFFSET		0x2
+
+struct ts4800_ts {
+	struct input_polled_dev *poll_dev;
+	struct device           *dev;
+	char                    phys[32];
+
+	void __iomem            *base;
+	struct regmap           *regmap;
+	unsigned int            reg;
+	unsigned int            bit;
+
+	bool                    pendown;
+	int                     debounce;
+};
+
+static void ts4800_ts_open(struct input_polled_dev *dev)
+{
+	struct ts4800_ts *ts = dev->private;
+	int ret;
+
+	ts->pendown = false;
+	ts->debounce = DEBOUNCE_COUNT;
+
+	ret = regmap_update_bits(ts->regmap, ts->reg, ts->bit, ts->bit);
+	if (ret)
+		dev_warn(ts->dev, "Failed to enable touchscreen\n");
+}
+
+static void ts4800_ts_close(struct input_polled_dev *dev)
+{
+	struct ts4800_ts *ts = dev->private;
+	int ret;
+
+	ret = regmap_update_bits(ts->regmap, ts->reg, ts->bit, 0);
+	if (ret)
+		dev_warn(ts->dev, "Failed to disable touchscreen\n");
+
+}
+
+static void ts4800_ts_poll(struct input_polled_dev *dev)
+{
+	struct input_dev *input_dev = dev->input;
+	struct ts4800_ts *ts = dev->private;
+	u16 last_x = readw(ts->base + X_OFFSET);
+	u16 last_y = readw(ts->base + Y_OFFSET);
+	bool pendown = last_x & PENDOWN_MASK;
+
+	if (pendown) {
+		if (ts->debounce) {
+			ts->debounce--;
+			return;
+		}
+
+		if (!ts->pendown) {
+			input_report_key(input_dev, BTN_TOUCH, 1);
+			ts->pendown = true;
+		}
+
+		last_x = ((~last_x) >> 4) & MAX_12BIT;
+		last_y = ((~last_y) >> 4) & MAX_12BIT;
+
+		input_report_abs(input_dev, ABS_X, last_x);
+		input_report_abs(input_dev, ABS_Y, last_y);
+		input_sync(input_dev);
+	} else if (ts->pendown) {
+		ts->pendown = false;
+		ts->debounce = DEBOUNCE_COUNT;
+		input_report_key(input_dev, BTN_TOUCH, 0);
+		input_sync(input_dev);
+	}
+}
+
+static int ts4800_parse_dt(struct platform_device *pdev,
+			   struct ts4800_ts *ts)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *syscon_np;
+	u32 reg, bit;
+	int error;
+
+	syscon_np = of_parse_phandle(np, "syscon", 0);
+	if (!syscon_np) {
+		dev_err(dev, "no syscon property\n");
+		return -ENODEV;
+	}
+
+	error = of_property_read_u32_index(np, "syscon", 1, &reg);
+	if (error < 0) {
+		dev_err(dev, "no offset in syscon\n");
+		return error;
+	}
+
+	ts->reg = reg;
+
+	error = of_property_read_u32_index(np, "syscon", 2, &bit);
+	if (error < 0) {
+		dev_err(dev, "no bit in syscon\n");
+		return error;
+	}
+
+	ts->bit = BIT(bit);
+
+	ts->regmap = syscon_node_to_regmap(syscon_np);
+	if (IS_ERR(ts->regmap)) {
+		dev_err(dev, "cannot get parent's regmap\n");
+		return PTR_ERR(ts->regmap);
+	}
+
+	return 0;
+}
+
+static int ts4800_ts_probe(struct platform_device *pdev)
+{
+	struct input_polled_dev *poll_dev;
+	struct ts4800_ts *ts;
+	struct resource *res;
+	int error;
+
+	ts = devm_kzalloc(&pdev->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	error = ts4800_parse_dt(pdev, ts);
+	if (error)
+		return error;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ts->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ts->base))
+		return PTR_ERR(ts->base);
+
+	poll_dev = devm_input_allocate_polled_device(&pdev->dev);
+	if (!poll_dev)
+		return -ENOMEM;
+
+	snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&pdev->dev));
+	ts->poll_dev = poll_dev;
+	ts->dev = &pdev->dev;
+
+	poll_dev->private = ts;
+	poll_dev->poll_interval = POLL_INTERVAL;
+	poll_dev->open = ts4800_ts_open;
+	poll_dev->close = ts4800_ts_close;
+	poll_dev->poll = ts4800_ts_poll;
+
+	poll_dev->input->name = "TS-4800 Touchscreen";
+	poll_dev->input->phys = ts->phys;
+
+	input_set_capability(poll_dev->input, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(poll_dev->input, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(poll_dev->input, ABS_Y, 0, MAX_12BIT, 0, 0);
+
+	error = input_register_polled_device(poll_dev);
+	if (error) {
+		dev_err(&pdev->dev,
+			"Unabled to register polled input device (%d)\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id ts4800_ts_of_match[] = {
+	{ .compatible = "technologic,ts4800-ts", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ts4800_ts_of_match);
+
+static struct platform_driver ts4800_ts_driver = {
+	.driver = {
+		.name = "ts4800-ts",
+		.of_match_table = ts4800_ts_of_match,
+	},
+	.probe = ts4800_ts_probe,
+};
+module_platform_driver(ts4800_ts_driver);
+
+MODULE_AUTHOR("Damien Riegel <damien.riegel@savoirfairelinux.com>");
+MODULE_DESCRIPTION("TS-4800 Touchscreen Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ts4800_ts");
diff --git a/drivers/input/touchscreen/wacom_w8001.c b/drivers/input/touchscreen/wacom_w8001.c
index 2792ca397dd0..bab3c6acf6a2 100644
--- a/drivers/input/touchscreen/wacom_w8001.c
+++ b/drivers/input/touchscreen/wacom_w8001.c
@@ -80,7 +80,8 @@ struct w8001_touch_query {
  */
 
 struct w8001 {
-	struct input_dev *dev;
+	struct input_dev *pen_dev;
+	struct input_dev *touch_dev;
 	struct serio *serio;
 	struct completion cmd_done;
 	int id;
@@ -95,7 +96,10 @@ struct w8001 {
 	u16 max_touch_y;
 	u16 max_pen_x;
 	u16 max_pen_y;
-	char name[64];
+	char pen_name[64];
+	char touch_name[64];
+	int open_count;
+	struct mutex mutex;
 };
 
 static void parse_pen_data(u8 *data, struct w8001_coord *coord)
@@ -141,7 +145,7 @@ static void scale_touch_coordinates(struct w8001 *w8001,
 
 static void parse_multi_touch(struct w8001 *w8001)
 {
-	struct input_dev *dev = w8001->dev;
+	struct input_dev *dev = w8001->touch_dev;
 	unsigned char *data = w8001->data;
 	unsigned int x, y;
 	int i;
@@ -151,7 +155,6 @@ static void parse_multi_touch(struct w8001 *w8001)
 		bool touch = data[0] & (1 << i);
 
 		input_mt_slot(dev, i);
-		input_mt_report_slot_state(dev, MT_TOOL_FINGER, touch);
 		if (touch) {
 			x = (data[6 * i + 1] << 7) | data[6 * i + 2];
 			y = (data[6 * i + 3] << 7) | data[6 * i + 4];
@@ -207,7 +210,7 @@ static void parse_touchquery(u8 *data, struct w8001_touch_query *query)
 
 static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
 {
-	struct input_dev *dev = w8001->dev;
+	struct input_dev *dev = w8001->pen_dev;
 
 	/*
 	 * We have 1 bit for proximity (rdy) and 3 bits for tip, side,
@@ -233,11 +236,6 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
 		break;
 
 	case BTN_TOOL_FINGER:
-		input_report_key(dev, BTN_TOUCH, 0);
-		input_report_key(dev, BTN_TOOL_FINGER, 0);
-		input_sync(dev);
-		/* fall through */
-
 	case KEY_RESERVED:
 		w8001->type = coord->f2 ? BTN_TOOL_RUBBER : BTN_TOOL_PEN;
 		break;
@@ -261,7 +259,7 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
 
 static void report_single_touch(struct w8001 *w8001, struct w8001_coord *coord)
 {
-	struct input_dev *dev = w8001->dev;
+	struct input_dev *dev = w8001->touch_dev;
 	unsigned int x = coord->x;
 	unsigned int y = coord->y;
 
@@ -271,7 +269,6 @@ static void report_single_touch(struct w8001 *w8001, struct w8001_coord *coord)
 	input_report_abs(dev, ABS_X, x);
 	input_report_abs(dev, ABS_Y, y);
 	input_report_key(dev, BTN_TOUCH, coord->tsw);
-	input_report_key(dev, BTN_TOOL_FINGER, coord->tsw);
 
 	input_sync(dev);
 
@@ -369,22 +366,36 @@ static int w8001_command(struct w8001 *w8001, unsigned char command,
 static int w8001_open(struct input_dev *dev)
 {
 	struct w8001 *w8001 = input_get_drvdata(dev);
+	int err;
 
-	return w8001_command(w8001, W8001_CMD_START, false);
+	err = mutex_lock_interruptible(&w8001->mutex);
+	if (err)
+		return err;
+
+	if (w8001->open_count++ == 0) {
+		err = w8001_command(w8001, W8001_CMD_START, false);
+		if (err)
+			w8001->open_count--;
+	}
+
+	mutex_unlock(&w8001->mutex);
+	return err;
 }
 
 static void w8001_close(struct input_dev *dev)
 {
 	struct w8001 *w8001 = input_get_drvdata(dev);
 
-	w8001_command(w8001, W8001_CMD_STOP, false);
+	mutex_lock(&w8001->mutex);
+
+	if (--w8001->open_count == 0)
+		w8001_command(w8001, W8001_CMD_STOP, false);
+
+	mutex_unlock(&w8001->mutex);
 }
 
-static int w8001_setup(struct w8001 *w8001)
+static int w8001_detect(struct w8001 *w8001)
 {
-	struct input_dev *dev = w8001->dev;
-	struct w8001_coord coord;
-	struct w8001_touch_query touch;
 	int error;
 
 	error = w8001_command(w8001, W8001_CMD_STOP, false);
@@ -393,105 +404,145 @@ static int w8001_setup(struct w8001 *w8001)
 
 	msleep(250);	/* wait 250ms before querying the device */
 
-	dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
-	strlcat(w8001->name, "Wacom Serial", sizeof(w8001->name));
+	return 0;
+}
 
-	__set_bit(INPUT_PROP_DIRECT, dev->propbit);
+static int w8001_setup_pen(struct w8001 *w8001, char *basename,
+			   size_t basename_sz)
+{
+	struct input_dev *dev = w8001->pen_dev;
+	struct w8001_coord coord;
+	int error;
 
 	/* penabled? */
 	error = w8001_command(w8001, W8001_CMD_QUERY, true);
-	if (!error) {
-		__set_bit(BTN_TOUCH, dev->keybit);
-		__set_bit(BTN_TOOL_PEN, dev->keybit);
-		__set_bit(BTN_TOOL_RUBBER, dev->keybit);
-		__set_bit(BTN_STYLUS, dev->keybit);
-		__set_bit(BTN_STYLUS2, dev->keybit);
-
-		parse_pen_data(w8001->response, &coord);
-		w8001->max_pen_x = coord.x;
-		w8001->max_pen_y = coord.y;
-
-		input_set_abs_params(dev, ABS_X, 0, coord.x, 0, 0);
-		input_set_abs_params(dev, ABS_Y, 0, coord.y, 0, 0);
-		input_abs_set_res(dev, ABS_X, W8001_PEN_RESOLUTION);
-		input_abs_set_res(dev, ABS_Y, W8001_PEN_RESOLUTION);
-		input_set_abs_params(dev, ABS_PRESSURE, 0, coord.pen_pressure, 0, 0);
-		if (coord.tilt_x && coord.tilt_y) {
-			input_set_abs_params(dev, ABS_TILT_X, 0, coord.tilt_x, 0, 0);
-			input_set_abs_params(dev, ABS_TILT_Y, 0, coord.tilt_y, 0, 0);
-		}
-		w8001->id = 0x90;
-		strlcat(w8001->name, " Penabled", sizeof(w8001->name));
+	if (error)
+		return error;
+
+	__set_bit(EV_KEY, dev->evbit);
+	__set_bit(EV_ABS, dev->evbit);
+	__set_bit(BTN_TOUCH, dev->keybit);
+	__set_bit(BTN_TOOL_PEN, dev->keybit);
+	__set_bit(BTN_TOOL_RUBBER, dev->keybit);
+	__set_bit(BTN_STYLUS, dev->keybit);
+	__set_bit(BTN_STYLUS2, dev->keybit);
+	__set_bit(INPUT_PROP_DIRECT, dev->propbit);
+
+	parse_pen_data(w8001->response, &coord);
+	w8001->max_pen_x = coord.x;
+	w8001->max_pen_y = coord.y;
+
+	input_set_abs_params(dev, ABS_X, 0, coord.x, 0, 0);
+	input_set_abs_params(dev, ABS_Y, 0, coord.y, 0, 0);
+	input_abs_set_res(dev, ABS_X, W8001_PEN_RESOLUTION);
+	input_abs_set_res(dev, ABS_Y, W8001_PEN_RESOLUTION);
+	input_set_abs_params(dev, ABS_PRESSURE, 0, coord.pen_pressure, 0, 0);
+	if (coord.tilt_x && coord.tilt_y) {
+		input_set_abs_params(dev, ABS_TILT_X, 0, coord.tilt_x, 0, 0);
+		input_set_abs_params(dev, ABS_TILT_Y, 0, coord.tilt_y, 0, 0);
 	}
 
+	w8001->id = 0x90;
+	strlcat(basename, " Penabled", basename_sz);
+
+	return 0;
+}
+
+static int w8001_setup_touch(struct w8001 *w8001, char *basename,
+			     size_t basename_sz)
+{
+	struct input_dev *dev = w8001->touch_dev;
+	struct w8001_touch_query touch;
+	int error;
+
+
 	/* Touch enabled? */
 	error = w8001_command(w8001, W8001_CMD_TOUCHQUERY, true);
-
+	if (error)
+		return error;
 	/*
 	 * Some non-touch devices may reply to the touch query. But their
 	 * second byte is empty, which indicates touch is not supported.
 	 */
-	if (!error && w8001->response[1]) {
-		__set_bit(BTN_TOUCH, dev->keybit);
-		__set_bit(BTN_TOOL_FINGER, dev->keybit);
-
-		parse_touchquery(w8001->response, &touch);
-		w8001->max_touch_x = touch.x;
-		w8001->max_touch_y = touch.y;
-
-		if (w8001->max_pen_x && w8001->max_pen_y) {
-			/* if pen is supported scale to pen maximum */
-			touch.x = w8001->max_pen_x;
-			touch.y = w8001->max_pen_y;
-			touch.panel_res = W8001_PEN_RESOLUTION;
-		}
+	if (!w8001->response[1])
+		return -ENXIO;
 
-		input_set_abs_params(dev, ABS_X, 0, touch.x, 0, 0);
-		input_set_abs_params(dev, ABS_Y, 0, touch.y, 0, 0);
-		input_abs_set_res(dev, ABS_X, touch.panel_res);
-		input_abs_set_res(dev, ABS_Y, touch.panel_res);
-
-		switch (touch.sensor_id) {
-		case 0:
-		case 2:
-			w8001->pktlen = W8001_PKTLEN_TOUCH93;
-			w8001->id = 0x93;
-			strlcat(w8001->name, " 1FG", sizeof(w8001->name));
-			break;
+	__set_bit(EV_KEY, dev->evbit);
+	__set_bit(EV_ABS, dev->evbit);
+	__set_bit(BTN_TOUCH, dev->keybit);
+	__set_bit(INPUT_PROP_DIRECT, dev->propbit);
 
-		case 1:
-		case 3:
-		case 4:
-			w8001->pktlen = W8001_PKTLEN_TOUCH9A;
-			strlcat(w8001->name, " 1FG", sizeof(w8001->name));
-			w8001->id = 0x9a;
-			break;
+	parse_touchquery(w8001->response, &touch);
+	w8001->max_touch_x = touch.x;
+	w8001->max_touch_y = touch.y;
 
-		case 5:
-			w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
-
-			input_mt_init_slots(dev, 2, 0);
-			input_set_abs_params(dev, ABS_MT_POSITION_X,
-						0, touch.x, 0, 0);
-			input_set_abs_params(dev, ABS_MT_POSITION_Y,
-						0, touch.y, 0, 0);
-			input_set_abs_params(dev, ABS_MT_TOOL_TYPE,
-						0, MT_TOOL_MAX, 0, 0);
-
-			strlcat(w8001->name, " 2FG", sizeof(w8001->name));
-			if (w8001->max_pen_x && w8001->max_pen_y)
-				w8001->id = 0xE3;
-			else
-				w8001->id = 0xE2;
-			break;
-		}
+	if (w8001->max_pen_x && w8001->max_pen_y) {
+		/* if pen is supported scale to pen maximum */
+		touch.x = w8001->max_pen_x;
+		touch.y = w8001->max_pen_y;
+		touch.panel_res = W8001_PEN_RESOLUTION;
+	}
+
+	input_set_abs_params(dev, ABS_X, 0, touch.x, 0, 0);
+	input_set_abs_params(dev, ABS_Y, 0, touch.y, 0, 0);
+	input_abs_set_res(dev, ABS_X, touch.panel_res);
+	input_abs_set_res(dev, ABS_Y, touch.panel_res);
+
+	switch (touch.sensor_id) {
+	case 0:
+	case 2:
+		w8001->pktlen = W8001_PKTLEN_TOUCH93;
+		w8001->id = 0x93;
+		strlcat(basename, " 1FG", basename_sz);
+		break;
+
+	case 1:
+	case 3:
+	case 4:
+		w8001->pktlen = W8001_PKTLEN_TOUCH9A;
+		strlcat(basename, " 1FG", basename_sz);
+		w8001->id = 0x9a;
+		break;
+
+	case 5:
+		w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
+
+		__set_bit(BTN_TOOL_DOUBLETAP, dev->keybit);
+		input_mt_init_slots(dev, 2, 0);
+		input_set_abs_params(dev, ABS_MT_POSITION_X,
+					0, touch.x, 0, 0);
+		input_set_abs_params(dev, ABS_MT_POSITION_Y,
+					0, touch.y, 0, 0);
+
+		strlcat(basename, " 2FG", basename_sz);
+		if (w8001->max_pen_x && w8001->max_pen_y)
+			w8001->id = 0xE3;
+		else
+			w8001->id = 0xE2;
+		break;
 	}
 
-	strlcat(w8001->name, " Touchscreen", sizeof(w8001->name));
+	strlcat(basename, " Touchscreen", basename_sz);
 
 	return 0;
 }
 
+static void w8001_set_devdata(struct input_dev *dev, struct w8001 *w8001,
+			      struct serio *serio)
+{
+	dev->phys = w8001->phys;
+	dev->id.bustype = BUS_RS232;
+	dev->id.product = w8001->id;
+	dev->id.vendor = 0x056a;
+	dev->id.version = 0x0100;
+	dev->open = w8001_open;
+	dev->close = w8001_close;
+
+	dev->dev.parent = &serio->dev;
+
+	input_set_drvdata(dev, w8001);
+}
+
 /*
  * w8001_disconnect() is the opposite of w8001_connect()
  */
@@ -502,7 +553,10 @@ static void w8001_disconnect(struct serio *serio)
 
 	serio_close(serio);
 
-	input_unregister_device(w8001->dev);
+	if (w8001->pen_dev)
+		input_unregister_device(w8001->pen_dev);
+	if (w8001->touch_dev)
+		input_unregister_device(w8001->touch_dev);
 	kfree(w8001);
 
 	serio_set_drvdata(serio, NULL);
@@ -517,18 +571,23 @@ static void w8001_disconnect(struct serio *serio)
 static int w8001_connect(struct serio *serio, struct serio_driver *drv)
 {
 	struct w8001 *w8001;
-	struct input_dev *input_dev;
-	int err;
+	struct input_dev *input_dev_pen;
+	struct input_dev *input_dev_touch;
+	char basename[64];
+	int err, err_pen, err_touch;
 
 	w8001 = kzalloc(sizeof(struct w8001), GFP_KERNEL);
-	input_dev = input_allocate_device();
-	if (!w8001 || !input_dev) {
+	input_dev_pen = input_allocate_device();
+	input_dev_touch = input_allocate_device();
+	if (!w8001 || !input_dev_pen || !input_dev_touch) {
 		err = -ENOMEM;
 		goto fail1;
 	}
 
 	w8001->serio = serio;
-	w8001->dev = input_dev;
+	w8001->pen_dev = input_dev_pen;
+	w8001->touch_dev = input_dev_touch;
+	mutex_init(&w8001->mutex);
 	init_completion(&w8001->cmd_done);
 	snprintf(w8001->phys, sizeof(w8001->phys), "%s/input0", serio->phys);
 
@@ -537,35 +596,67 @@ static int w8001_connect(struct serio *serio, struct serio_driver *drv)
 	if (err)
 		goto fail2;
 
-	err = w8001_setup(w8001);
+	err = w8001_detect(w8001);
 	if (err)
 		goto fail3;
 
-	input_dev->name = w8001->name;
-	input_dev->phys = w8001->phys;
-	input_dev->id.product = w8001->id;
-	input_dev->id.bustype = BUS_RS232;
-	input_dev->id.vendor = 0x056a;
-	input_dev->id.version = 0x0100;
-	input_dev->dev.parent = &serio->dev;
+	/* For backwards-compatibility we compose the basename based on
+	 * capabilities and then just append the tool type
+	 */
+	strlcpy(basename, "Wacom Serial", sizeof(basename));
+
+	err_pen = w8001_setup_pen(w8001, basename, sizeof(basename));
+	err_touch = w8001_setup_touch(w8001, basename, sizeof(basename));
+	if (err_pen && err_touch) {
+		err = -ENXIO;
+		goto fail3;
+	}
+
+	if (!err_pen) {
+		strlcpy(w8001->pen_name, basename, sizeof(w8001->pen_name));
+		strlcat(w8001->pen_name, " Pen", sizeof(w8001->pen_name));
+		input_dev_pen->name = w8001->pen_name;
 
-	input_dev->open = w8001_open;
-	input_dev->close = w8001_close;
+		w8001_set_devdata(input_dev_pen, w8001, serio);
 
-	input_set_drvdata(input_dev, w8001);
+		err = input_register_device(w8001->pen_dev);
+		if (err)
+			goto fail3;
+	} else {
+		input_free_device(input_dev_pen);
+		input_dev_pen = NULL;
+		w8001->pen_dev = NULL;
+	}
 
-	err = input_register_device(w8001->dev);
-	if (err)
-		goto fail3;
+	if (!err_touch) {
+		strlcpy(w8001->touch_name, basename, sizeof(w8001->touch_name));
+		strlcat(w8001->touch_name, " Finger",
+			sizeof(w8001->touch_name));
+		input_dev_touch->name = w8001->touch_name;
+
+		w8001_set_devdata(input_dev_touch, w8001, serio);
+
+		err = input_register_device(w8001->touch_dev);
+		if (err)
+			goto fail4;
+	} else {
+		input_free_device(input_dev_touch);
+		input_dev_touch = NULL;
+		w8001->touch_dev = NULL;
+	}
 
 	return 0;
 
+fail4:
+	if (w8001->pen_dev)
+		input_unregister_device(w8001->pen_dev);
 fail3:
 	serio_close(serio);
 fail2:
 	serio_set_drvdata(serio, NULL);
 fail1:
-	input_free_device(input_dev);
+	input_free_device(input_dev_pen);
+	input_free_device(input_dev_touch);
 	kfree(w8001);
 	return err;
 }