Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 461 insertions, 0 deletions

diff --git a/drivers/macintosh/macserial.h b/drivers/macintosh/macserial.h
new file mode 100644
index 000000000000..bade11a7a5c3
--- /dev/null
+++ b/drivers/macintosh/macserial.h
@@ -0,0 +1,461 @@
+/*
+ * macserial.h: Definitions for the Macintosh Z8530 serial driver.
+ *
+ * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras.
+ *
+ * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au)
+ * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu)
+ */
+#ifndef _MACSERIAL_H
+#define _MACSERIAL_H
+
+#include <linux/spinlock.h>
+
+#define NUM_ZSREGS    16
+
+struct serial_struct {
+	int	type;
+	int	line;
+	int	port;
+	int	irq;
+	int	flags;
+	int	xmit_fifo_size;
+	int	custom_divisor;
+	int	baud_base;
+	unsigned short	close_delay;
+	char	reserved_char[2];
+	int	hub6;
+	unsigned short	closing_wait; /* time to wait before closing */
+	unsigned short	closing_wait2; /* no longer used... */
+	int	reserved[4];
+};
+
+/*
+ * For the close wait times, 0 means wait forever for serial port to
+ * flush its output.  65535 means don't wait at all.
+ */
+#define ZILOG_CLOSING_WAIT_INF	0
+#define ZILOG_CLOSING_WAIT_NONE	65535
+
+/*
+ * Definitions for ZILOG_struct (and serial_struct) flags field
+ */
+#define ZILOG_HUP_NOTIFY	0x0001	/* Notify getty on hangups and closes 
+				   	 * on the callout port */
+#define ZILOG_FOURPORT 		0x0002	/* Set OU1, OUT2 per AST Fourport settings */
+#define ZILOG_SAK		0x0004	/* Secure Attention Key (Orange book) */
+#define ZILOG_SPLIT_TERMIOS	0x0008	/* Separate termios for dialin/callout */
+
+#define ZILOG_SPD_MASK		0x0030
+#define ZILOG_SPD_HI		0x0010	/* Use 56000 instead of 38400 bps */
+
+#define ZILOG_SPD_VHI		0x0020  /* Use 115200 instead of 38400 bps */
+#define ZILOG_SPD_CUST		0x0030  /* Use user-specified divisor */
+
+#define ZILOG_SKIP_TEST		0x0040	/* Skip UART test during autoconfiguration */
+#define ZILOG_AUTO_IRQ 		0x0080	/* Do automatic IRQ during autoconfiguration */
+#define ZILOG_SESSION_LOCKOUT	0x0100	/* Lock out cua opens based on session */
+#define ZILOG_PGRP_LOCKOUT	0x0200	/* Lock out cua opens based on pgrp */
+#define ZILOG_CALLOUT_NOHUP	0x0400	/* Don't do hangups for cua device */
+
+#define ZILOG_FLAGS		0x0FFF	/* Possible legal ZILOG flags */
+#define ZILOG_USR_MASK		0x0430	/* Legal flags that non-privileged
+					 * users can set or reset */
+
+/* Internal flags used only by kernel/chr_drv/serial.c */
+#define ZILOG_INITIALIZED	0x80000000 /* Serial port was initialized */
+#define ZILOG_CALLOUT_ACTIVE	0x40000000 /* Call out device is active */
+#define ZILOG_NORMAL_ACTIVE	0x20000000 /* Normal device is active */
+#define ZILOG_BOOT_AUTOCONF	0x10000000 /* Autoconfigure port on bootup */
+#define ZILOG_CLOSING		0x08000000 /* Serial port is closing */
+#define ZILOG_CTS_FLOW		0x04000000 /* Do CTS flow control */
+#define ZILOG_CHECK_CD		0x02000000 /* i.e., CLOCAL */
+#define ZILOG_SLEEPING		0x01000000 /* have shut it down for sleep */
+
+/* Software state per channel */
+
+#ifdef __KERNEL__
+/*
+ * This is our internal structure for each serial port's state.
+ * 
+ * Many fields are paralleled by the structure used by the serial_struct
+ * structure.
+ *
+ * For definitions of the flags field, see tty.h
+ */
+
+struct mac_serial;
+
+struct mac_zschannel {
+	volatile unsigned char*	control;
+	volatile unsigned char*	data;
+	spinlock_t		lock;
+	/* Used for debugging */
+	struct mac_serial*	parent;
+};
+
+struct mac_dma {
+	volatile struct dbdma_regs	dma;
+	volatile unsigned short		res_count;
+	volatile unsigned short		command;
+	volatile unsigned int		buf_addr;
+};
+
+struct mac_serial {
+	struct mac_serial *zs_next;	/* For IRQ servicing chain */
+	struct mac_zschannel *zs_channel; /* Channel registers */
+	struct mac_zschannel *zs_chan_a;	/* A side registers */
+	unsigned char read_reg_zero;
+	struct device_node* dev_node;
+	spinlock_t lock;
+
+	char soft_carrier;  /* Use soft carrier on this channel */
+	char break_abort;   /* Is serial console in, so process brk/abrt */
+	char kgdb_channel;  /* Kgdb is running on this channel */
+	char is_cons;       /* Is this our console. */
+	char is_internal_modem; /* is connected to an internal modem */
+	char is_irda;		/* is connected to an IrDA codec */
+	int port_type;		/* Port type for pmac_feature */
+	unsigned char tx_active; /* character is being xmitted */
+	unsigned char tx_stopped; /* output is suspended */
+	unsigned char power_wait; /* waiting for power-up delay to expire */
+
+	/* We need to know the current clock divisor
+	 * to read the bps rate the chip has currently
+	 * loaded.
+	 */
+	unsigned char clk_divisor;  /* May be 1, 16, 32, or 64 */
+	int zs_baud;
+
+	/* Current write register values */
+	unsigned char curregs[NUM_ZSREGS];
+
+	/* Values we need to set next opportunity */
+	unsigned char pendregs[NUM_ZSREGS];
+
+	char change_needed;
+
+	int			magic;
+	int			baud_base;
+	int			port;
+	int			irq;
+	int			flags; 		/* defined in tty.h */
+	int			type; 		/* UART type */
+	struct tty_struct 	*tty;
+	int			read_status_mask;
+	int			ignore_status_mask;
+	int			timeout;
+	int			xmit_fifo_size;
+	int			custom_divisor;
+	int			x_char;	/* xon/xoff character */
+	int			close_delay;
+	unsigned short		closing_wait;
+	unsigned short		closing_wait2;
+	unsigned long		event;
+	unsigned long		last_active;
+	int			line;
+	int			count;	    /* # of fd on device */
+	int			blocked_open; /* # of blocked opens */
+	unsigned char 		*xmit_buf;
+	int			xmit_head;
+	int			xmit_tail;
+	int			xmit_cnt;
+	struct work_struct	tqueue;
+	wait_queue_head_t	open_wait;
+	wait_queue_head_t	close_wait;
+
+	volatile struct dbdma_regs *tx_dma;
+	int			tx_dma_irq;
+	volatile struct dbdma_cmd *tx_cmds;
+	volatile struct mac_dma *rx;
+	int 			rx_dma_irq;
+	volatile struct dbdma_cmd **rx_cmds;
+	unsigned char		**rx_char_buf;
+	unsigned char		**rx_flag_buf;
+#define	RX_BUF_SIZE	256
+	int			rx_nbuf;
+	int			rx_done_bytes;
+	int			rx_ubuf;
+	int			rx_fbuf;
+#define	RX_NO_FBUF	(-1)
+	int			rx_cbuf;
+	spinlock_t		rx_dma_lock;
+	int			has_dma;
+	int			dma_initted;
+	void			*dma_priv;
+	struct timer_list	poll_dma_timer;
+#define RX_DMA_TIMER	(jiffies + 10*HZ/1000)
+
+	struct timer_list	powerup_timer;
+};
+
+
+#define SERIAL_MAGIC 0x5301
+
+/*
+ * The size of the serial xmit buffer is 1 page, or 4096 bytes
+ */
+#define SERIAL_XMIT_SIZE 4096
+
+/*
+ * Events are used to schedule things to happen at timer-interrupt
+ * time, instead of at rs interrupt time.
+ */
+#define RS_EVENT_WRITE_WAKEUP	0
+
+#endif /* __KERNEL__ */
+
+/* Conversion routines to/from brg time constants from/to bits
+ * per second.
+ */
+#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+/* The Zilog register set */
+
+#define	FLAG	0x7e
+
+/* Write Register 0 */
+#define	R0	0		/* Register selects */
+#define	R1	1
+#define	R2	2
+#define	R3	3
+#define	R4	4
+#define	R5	5
+#define	R6	6
+#define	R7	7
+#define	R8	8
+#define	R9	9
+#define	R10	10
+#define	R11	11
+#define	R12	12
+#define	R13	13
+#define	R14	14
+#define	R15	15
+
+#define	NULLCODE	0	/* Null Code */
+#define	POINT_HIGH	0x8	/* Select upper half of registers */
+#define	RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
+#define	SEND_ABORT	0x18	/* HDLC Abort */
+#define	RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
+#define	RES_Tx_P	0x28	/* Reset TxINT Pending */
+#define	ERR_RES		0x30	/* Error Reset */
+#define	RES_H_IUS	0x38	/* Reset highest IUS */
+
+#define	RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
+#define	RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
+#define	RES_EOM_L	0xC0	/* Reset EOM latch */
+
+/* Write Register 1 */
+
+#define	EXT_INT_ENAB	0x1	/* Ext Int Enable */
+#define	TxINT_ENAB	0x2	/* Tx Int Enable */
+#define	PAR_SPEC	0x4	/* Parity is special condition */
+
+#define	RxINT_DISAB	0	/* Rx Int Disable */
+#define	RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
+#define	INT_ALL_Rx	0x10	/* Int on all Rx Characters or error */
+#define	INT_ERR_Rx	0x18	/* Int on error only */
+
+#define	WT_RDY_RT	0x20	/* W/Req reflects recv if 1, xmit if 0 */
+#define	WT_FN_RDYFN	0x40	/* W/Req pin is DMA request if 1, wait if 0 */
+#define	WT_RDY_ENAB	0x80	/* Enable W/Req pin */
+
+/* Write Register #2 (Interrupt Vector) */
+
+/* Write Register 3 */
+
+#define	RxENABLE	0x1	/* Rx Enable */
+#define	SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
+#define	ADD_SM		0x4	/* Address Search Mode (SDLC) */
+#define	RxCRC_ENAB	0x8	/* Rx CRC Enable */
+#define	ENT_HM		0x10	/* Enter Hunt Mode */
+#define	AUTO_ENAB	0x20	/* Auto Enables */
+#define	Rx5		0x0	/* Rx 5 Bits/Character */
+#define	Rx7		0x40	/* Rx 7 Bits/Character */
+#define	Rx6		0x80	/* Rx 6 Bits/Character */
+#define	Rx8		0xc0	/* Rx 8 Bits/Character */
+#define RxNBITS_MASK	0xc0
+
+/* Write Register 4 */
+
+#define	PAR_ENA		0x1	/* Parity Enable */
+#define	PAR_EVEN	0x2	/* Parity Even/Odd* */
+
+#define	SYNC_ENAB	0	/* Sync Modes Enable */
+#define	SB1		0x4	/* 1 stop bit/char */
+#define	SB15		0x8	/* 1.5 stop bits/char */
+#define	SB2		0xc	/* 2 stop bits/char */
+#define SB_MASK		0xc
+
+#define	MONSYNC		0	/* 8 Bit Sync character */
+#define	BISYNC		0x10	/* 16 bit sync character */
+#define	SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
+#define	EXTSYNC		0x30	/* External Sync Mode */
+
+#define	X1CLK		0x0	/* x1 clock mode */
+#define	X16CLK		0x40	/* x16 clock mode */
+#define	X32CLK		0x80	/* x32 clock mode */
+#define	X64CLK		0xC0	/* x64 clock mode */
+#define XCLK_MASK	0xC0
+
+/* Write Register 5 */
+
+#define	TxCRC_ENAB	0x1	/* Tx CRC Enable */
+#define	RTS		0x2	/* RTS */
+#define	SDLC_CRC	0x4	/* SDLC/CRC-16 */
+#define	TxENAB		0x8	/* Tx Enable */
+#define	SND_BRK		0x10	/* Send Break */
+#define	Tx5		0x0	/* Tx 5 bits (or less)/character */
+#define	Tx7		0x20	/* Tx 7 bits/character */
+#define	Tx6		0x40	/* Tx 6 bits/character */
+#define	Tx8		0x60	/* Tx 8 bits/character */
+#define TxNBITS_MASK	0x60
+#define	DTR		0x80	/* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 7' (Some enhanced feature control) */
+#define	ENEXREAD	0x40	/* Enable read of some write registers */
+
+/* Write Register 8 (transmit buffer) */
+
+/* Write Register 9 (Master interrupt control) */
+#define	VIS	1	/* Vector Includes Status */
+#define	NV	2	/* No Vector */
+#define	DLC	4	/* Disable Lower Chain */
+#define	MIE	8	/* Master Interrupt Enable */
+#define	STATHI	0x10	/* Status high */
+#define	NORESET	0	/* No reset on write to R9 */
+#define	CHRB	0x40	/* Reset channel B */
+#define	CHRA	0x80	/* Reset channel A */
+#define	FHWRES	0xc0	/* Force hardware reset */
+
+/* Write Register 10 (misc control bits) */
+#define	BIT6	1	/* 6 bit/8bit sync */
+#define	LOOPMODE 2	/* SDLC Loop mode */
+#define	ABUNDER	4	/* Abort/flag on SDLC xmit underrun */
+#define	MARKIDLE 8	/* Mark/flag on idle */
+#define	GAOP	0x10	/* Go active on poll */
+#define	NRZ	0	/* NRZ mode */
+#define	NRZI	0x20	/* NRZI mode */
+#define	FM1	0x40	/* FM1 (transition = 1) */
+#define	FM0	0x60	/* FM0 (transition = 0) */
+#define	CRCPS	0x80	/* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode control) */
+#define	TRxCXT	0	/* TRxC = Xtal output */
+#define	TRxCTC	1	/* TRxC = Transmit clock */
+#define	TRxCBR	2	/* TRxC = BR Generator Output */
+#define	TRxCDP	3	/* TRxC = DPLL output */
+#define	TRxCOI	4	/* TRxC O/I */
+#define	TCRTxCP	0	/* Transmit clock = RTxC pin */
+#define	TCTRxCP	8	/* Transmit clock = TRxC pin */
+#define	TCBR	0x10	/* Transmit clock = BR Generator output */
+#define	TCDPLL	0x18	/* Transmit clock = DPLL output */
+#define	RCRTxCP	0	/* Receive clock = RTxC pin */
+#define	RCTRxCP	0x20	/* Receive clock = TRxC pin */
+#define	RCBR	0x40	/* Receive clock = BR Generator output */
+#define	RCDPLL	0x60	/* Receive clock = DPLL output */
+#define	RTxCX	0x80	/* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (lower byte of baud rate generator time constant) */
+
+/* Write Register 13 (upper byte of baud rate generator time constant) */
+
+/* Write Register 14 (Misc control bits) */
+#define	BRENABL	1	/* Baud rate generator enable */
+#define	BRSRC	2	/* Baud rate generator source */
+#define	DTRREQ	4	/* DTR/Request function */
+#define	AUTOECHO 8	/* Auto Echo */
+#define	LOOPBAK	0x10	/* Local loopback */
+#define	SEARCH	0x20	/* Enter search mode */
+#define	RMC	0x40	/* Reset missing clock */
+#define	DISDPLL	0x60	/* Disable DPLL */
+#define	SSBR	0x80	/* Set DPLL source = BR generator */
+#define	SSRTxC	0xa0	/* Set DPLL source = RTxC */
+#define	SFMM	0xc0	/* Set FM mode */
+#define	SNRZI	0xe0	/* Set NRZI mode */
+
+/* Write Register 15 (external/status interrupt control) */
+#define	EN85C30	1	/* Enable some 85c30-enhanced registers */
+#define	ZCIE	2	/* Zero count IE */
+#define	ENSTFIFO 4	/* Enable status FIFO (SDLC) */
+#define	DCDIE	8	/* DCD IE */
+#define	SYNCIE	0x10	/* Sync/hunt IE */
+#define	CTSIE	0x20	/* CTS IE */
+#define	TxUIE	0x40	/* Tx Underrun/EOM IE */
+#define	BRKIE	0x80	/* Break/Abort IE */
+
+
+/* Read Register 0 */
+#define	Rx_CH_AV	0x1	/* Rx Character Available */
+#define	ZCOUNT		0x2	/* Zero count */
+#define	Tx_BUF_EMP	0x4	/* Tx Buffer empty */
+#define	DCD		0x8	/* DCD */
+#define	SYNC_HUNT	0x10	/* Sync/hunt */
+#define	CTS		0x20	/* CTS */
+#define	TxEOM		0x40	/* Tx underrun */
+#define	BRK_ABRT	0x80	/* Break/Abort */
+
+/* Read Register 1 */
+#define	ALL_SNT		0x1	/* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define	RES3		0x8	/* 0/3 */
+#define	RES4		0x4	/* 0/4 */
+#define	RES5		0xc	/* 0/5 */
+#define	RES6		0x2	/* 0/6 */
+#define	RES7		0xa	/* 0/7 */
+#define	RES8		0x6	/* 0/8 */
+#define	RES18		0xe	/* 1/8 */
+#define	RES28		0x0	/* 2/8 */
+/* Special Rx Condition Interrupts */
+#define	PAR_ERR		0x10	/* Parity error */
+#define	Rx_OVR		0x20	/* Rx Overrun Error */
+#define	FRM_ERR		0x40	/* CRC/Framing Error */
+#define	END_FR		0x80	/* End of Frame (SDLC) */
+
+/* Read Register 2 (channel b only) - Interrupt vector */
+#define	CHB_Tx_EMPTY	0x00
+#define	CHB_EXT_STAT	0x02
+#define	CHB_Rx_AVAIL	0x04
+#define	CHB_SPECIAL	0x06
+#define	CHA_Tx_EMPTY	0x08
+#define	CHA_EXT_STAT	0x0a
+#define	CHA_Rx_AVAIL	0x0c
+#define	CHA_SPECIAL	0x0e
+#define	STATUS_MASK	0x06
+
+/* Read Register 3 (interrupt pending register) ch a only */
+#define	CHBEXT	0x1		/* Channel B Ext/Stat IP */
+#define	CHBTxIP	0x2		/* Channel B Tx IP */
+#define	CHBRxIP	0x4		/* Channel B Rx IP */
+#define	CHAEXT	0x8		/* Channel A Ext/Stat IP */
+#define	CHATxIP	0x10		/* Channel A Tx IP */
+#define	CHARxIP	0x20		/* Channel A Rx IP */
+
+/* Read Register 8 (receive data register) */
+
+/* Read Register 10  (misc status bits) */
+#define	ONLOOP	2		/* On loop */
+#define	LOOPSEND 0x10		/* Loop sending */
+#define	CLK2MIS	0x40		/* Two clocks missing */
+#define	CLK1MIS	0x80		/* One clock missing */
+
+/* Read Register 12 (lower byte of baud rate generator constant) */
+
+/* Read Register 13 (upper byte of baud rate generator constant) */
+
+/* Read Register 15 (value of WR 15) */
+
+/* Misc macros */
+#define ZS_CLEARERR(channel)    (write_zsreg(channel, 0, ERR_RES))
+#define ZS_CLEARFIFO(channel)   do { volatile unsigned char garbage; \
+				     garbage = read_zsdata(channel); \
+				     garbage = read_zsdata(channel); \
+				     garbage = read_zsdata(channel); \
+				} while(0)
+
+#endif /* !(_MACSERIAL_H) */