ewrk3/tulip: Move the DEC - Tulip drivers

Move the DEC - Tulip driver into drivers/net/ethernet/dec/tulip/
and make the necessary Kconfig and Makefile changes.

The Digital Equioment (DEC) driver ewrk3 was moved into
drivers/net/ethernet/dec/ and the remaining drivers (Tulip)
were moved into drivers/net/ethernet/dec/tulip/

CC: Tobias Ringstrom <tori@unhappy.mine.nu>
CC: Grant Grundler <grundler@parisc-linux.org>
CC: David Davies <davies@maniac.ultranet.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>

1 files changed, 0 insertions, 1959 deletions

diff --git a/drivers/net/ewrk3.c b/drivers/net/ewrk3.c
deleted file mode 100644
index 05a5f71451a7..000000000000
--- a/drivers/net/ewrk3.c
+++ /dev/null
@@ -1,1959 +0,0 @@
-/*  ewrk3.c: A DIGITAL EtherWORKS 3 ethernet driver for Linux.
-
-   Written 1994 by David C. Davies.
-
-   Copyright 1994 Digital Equipment Corporation.
-
-   This software may be used and distributed according to the terms of
-   the GNU General Public License, incorporated herein by reference.
-
-   This driver is written for the Digital Equipment Corporation series
-   of EtherWORKS ethernet cards:
-
-   DE203 Turbo (BNC)
-   DE204 Turbo (TP)
-   DE205 Turbo (TP BNC)
-
-   The driver has been tested on a relatively busy  network using the DE205
-   card and benchmarked with 'ttcp': it transferred 16M  of data at 975kB/s
-   (7.8Mb/s) to a DECstation 5000/200.
-
-   The author may be reached at davies@maniac.ultranet.com.
-
-   =========================================================================
-   This driver has been written  substantially  from scratch, although  its
-   inheritance of style and stack interface from 'depca.c' and in turn from
-   Donald Becker's 'lance.c' should be obvious.
-
-   The  DE203/4/5 boards  all  use a new proprietary   chip in place of the
-   LANCE chip used in prior cards  (DEPCA, DE100, DE200/1/2, DE210, DE422).
-   Use the depca.c driver in the standard distribution  for the LANCE based
-   cards from DIGITAL; this driver will not work with them.
-
-   The DE203/4/5 cards have 2  main modes: shared memory  and I/O only. I/O
-   only makes  all the card accesses through  I/O transactions and  no high
-   (shared)  memory is used. This  mode provides a >48% performance penalty
-   and  is deprecated in this  driver,  although allowed to provide initial
-   setup when hardstrapped.
-
-   The shared memory mode comes in 3 flavours: 2kB, 32kB and 64kB. There is
-   no point in using any mode other than the 2kB  mode - their performances
-   are virtually identical, although the driver has  been tested in the 2kB
-   and 32kB modes. I would suggest you uncomment the line:
-
-   FORCE_2K_MODE;
-
-   to allow the driver to configure the card as a  2kB card at your current
-   base  address, thus leaving more  room to clutter  your  system box with
-   other memory hungry boards.
-
-   As many ISA  and EISA cards  can be supported  under this driver  as you
-   wish, limited primarily  by the available IRQ lines,  rather than by the
-   available I/O addresses  (24 ISA,  16 EISA).   I have  checked different
-   configurations of  multiple  depca cards and  ewrk3 cards  and have  not
-   found a problem yet (provided you have at least depca.c v0.38) ...
-
-   The board IRQ setting   must be at  an unused  IRQ which is  auto-probed
-   using  Donald  Becker's autoprobe  routines.   All  these cards   are at
-   {5,10,11,15}.
-
-   No 16MB memory  limitation should exist with this  driver as DMA is  not
-   used and the common memory area is in low memory on the network card (my
-   current system has 20MB and I've not had problems yet).
-
-   The ability to load  this driver as a  loadable module has been included
-   and used  extensively during the  driver development (to save those long
-   reboot sequences). To utilise this ability, you have to do 8 things:
-
-   0) have a copy of the loadable modules code installed on your system.
-   1) copy ewrk3.c from the  /linux/drivers/net directory to your favourite
-   temporary directory.
-   2) edit the  source code near  line 1898 to reflect  the I/O address and
-   IRQ you're using.
-   3) compile  ewrk3.c, but include -DMODULE in  the command line to ensure
-   that the correct bits are compiled (see end of source code).
-   4) if you are wanting to add a new  card, goto 5. Otherwise, recompile a
-   kernel with the ewrk3 configuration turned off and reboot.
-   5) insmod ewrk3.o
-   [Alan Cox: Changed this so you can insmod ewrk3.o irq=x io=y]
-   [Adam Kropelin: now accepts irq=x1,x2 io=y1,y2 for multiple cards]
-   6) run the net startup bits for your new eth?? interface manually
-   (usually /etc/rc.inet[12] at boot time).
-   7) enjoy!
-
-   Note that autoprobing is not allowed in loadable modules - the system is
-   already up and running and you're messing with interrupts.
-
-   To unload a module, turn off the associated interface
-   'ifconfig eth?? down' then 'rmmod ewrk3'.
-
-   Promiscuous   mode has been  turned  off  in this driver,   but  all the
-   multicast  address bits  have been   turned on. This  improved the  send
-   performance on a busy network by about 13%.
-
-   Ioctl's have now been provided (primarily because  I wanted to grab some
-   packet size statistics). They  are patterned after 'plipconfig.c' from a
-   suggestion by Alan Cox.  Using these  ioctls, you can enable promiscuous
-   mode, add/delete multicast  addresses, change the hardware address,  get
-   packet size distribution statistics and muck around with the control and
-   status register. I'll add others if and when the need arises.
-
-   TO DO:
-   ------
-
-
-   Revision History
-   ----------------
-
-   Version   Date        Description
-
-   0.1     26-aug-94   Initial writing. ALPHA code release.
-   0.11    31-aug-94   Fixed: 2k mode memory base calc.,
-   LeMAC version calc.,
-   IRQ vector assignments during autoprobe.
-   0.12    31-aug-94   Tested working on LeMAC2 (DE20[345]-AC) card.
-   Fixed up MCA hash table algorithm.
-   0.20     4-sep-94   Added IOCTL functionality.
-   0.21    14-sep-94   Added I/O mode.
-   0.21axp 15-sep-94   Special version for ALPHA AXP Linux V1.0.
-   0.22    16-sep-94   Added more IOCTLs & tidied up.
-   0.23    21-sep-94   Added transmit cut through.
-   0.24    31-oct-94   Added uid checks in some ioctls.
-   0.30     1-nov-94   BETA code release.
-   0.31     5-dec-94   Added check/allocate region code.
-   0.32    16-jan-95   Broadcast packet fix.
-   0.33    10-Feb-95   Fix recognition bug reported by <bkm@star.rl.ac.uk>.
-   0.40    27-Dec-95   Rationalise MODULE and autoprobe code.
-   Rewrite for portability & updated.
-   ALPHA support from <jestabro@amt.tay1.dec.com>
-   Added verify_area() calls in ewrk3_ioctl() from
-   suggestion by <heiko@colossus.escape.de>.
-   Add new multicasting code.
-   0.41    20-Jan-96   Fix IRQ set up problem reported by
-   <kenneth@bbs.sas.ntu.ac.sg>.
-   0.42    22-Apr-96   Fix alloc_device() bug <jari@markkus2.fimr.fi>
-   0.43    16-Aug-96   Update alloc_device() to conform to de4x5.c
-   0.44    08-Nov-01   use library crc32 functions <Matt_Domsch@dell.com>
-   0.45    19-Jul-02   fix unaligned access on alpha <martin@bruli.net>
-   0.46    10-Oct-02   Multiple NIC support when module <akropel1@rochester.rr.com>
-   0.47    18-Oct-02   ethtool support <akropel1@rochester.rr.com>
-   0.48    18-Oct-02   cli/sti removal for 2.5 <vda@port.imtp.ilyichevsk.odessa.ua>
-   ioctl locking, signature search cleanup <akropel1@rochester.rr.com>
-
-   =========================================================================
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/crc32.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-#include <linux/ethtool.h>
-#include <linux/time.h>
-#include <linux/types.h>
-#include <linux/unistd.h>
-#include <linux/ctype.h>
-#include <linux/bitops.h>
-
-#include <asm/io.h>
-#include <asm/dma.h>
-#include <asm/uaccess.h>
-
-#include "ewrk3.h"
-
-#define DRV_NAME	"ewrk3"
-#define DRV_VERSION	"0.48"
-
-static char version[] __initdata =
-DRV_NAME ":v" DRV_VERSION " 2002/10/18 davies@maniac.ultranet.com\n";
-
-#ifdef EWRK3_DEBUG
-static int ewrk3_debug = EWRK3_DEBUG;
-#else
-static int ewrk3_debug = 1;
-#endif
-
-#define EWRK3_NDA 0xffe0	/* No Device Address */
-
-#define PROBE_LENGTH    32
-#define ETH_PROM_SIG    0xAA5500FFUL
-
-#ifndef EWRK3_SIGNATURE
-#define EWRK3_SIGNATURE {"DE203","DE204","DE205",""}
-#define EWRK3_STRLEN 8
-#endif
-
-#ifndef EWRK3_RAM_BASE_ADDRESSES
-#define EWRK3_RAM_BASE_ADDRESSES {0xc0000,0xd0000,0x00000}
-#endif
-
-/*
-   ** Sets up the I/O area for the autoprobe.
- */
-#define EWRK3_IO_BASE 0x100	/* Start address for probe search */
-#define EWRK3_IOP_INC 0x20	/* I/O address increment */
-#define EWRK3_TOTAL_SIZE 0x20	/* required I/O address length */
-
-#ifndef MAX_NUM_EWRK3S
-#define MAX_NUM_EWRK3S 21
-#endif
-
-#ifndef EWRK3_EISA_IO_PORTS
-#define EWRK3_EISA_IO_PORTS 0x0c00	/* I/O port base address, slot 0 */
-#endif
-
-#ifndef MAX_EISA_SLOTS
-#define MAX_EISA_SLOTS 16
-#define EISA_SLOT_INC 0x1000
-#endif
-
-#define QUEUE_PKT_TIMEOUT (1*HZ)	/* Jiffies */
-
-/*
-   ** EtherWORKS 3 shared memory window sizes
- */
-#define IO_ONLY         0x00
-#define SHMEM_2K        0x800
-#define SHMEM_32K       0x8000
-#define SHMEM_64K       0x10000
-
-/*
-   ** EtherWORKS 3 IRQ ENABLE/DISABLE
- */
-#define ENABLE_IRQs { \
-  icr |= lp->irq_mask;\
-  outb(icr, EWRK3_ICR);                     /* Enable the IRQs */\
-}
-
-#define DISABLE_IRQs { \
-  icr = inb(EWRK3_ICR);\
-  icr &= ~lp->irq_mask;\
-  outb(icr, EWRK3_ICR);                     /* Disable the IRQs */\
-}
-
-/*
-   ** EtherWORKS 3 START/STOP
- */
-#define START_EWRK3 { \
-  csr = inb(EWRK3_CSR);\
-  csr &= ~(CSR_TXD|CSR_RXD);\
-  outb(csr, EWRK3_CSR);                     /* Enable the TX and/or RX */\
-}
-
-#define STOP_EWRK3 { \
-  csr = (CSR_TXD|CSR_RXD);\
-  outb(csr, EWRK3_CSR);                     /* Disable the TX and/or RX */\
-}
-
-/*
-   ** The EtherWORKS 3 private structure
- */
-#define EWRK3_PKT_STAT_SZ 16
-#define EWRK3_PKT_BIN_SZ  128	/* Should be >=100 unless you
-				   increase EWRK3_PKT_STAT_SZ */
-
-struct ewrk3_stats {
-	u32 bins[EWRK3_PKT_STAT_SZ];
-	u32 unicast;
-	u32 multicast;
-	u32 broadcast;
-	u32 excessive_collisions;
-	u32 tx_underruns;
-	u32 excessive_underruns;
-};
-
-struct ewrk3_private {
-	char adapter_name[80];	/* Name exported to /proc/ioports */
-	u_long shmem_base;	/* Shared memory start address */
-	void __iomem *shmem;
-	u_long shmem_length;	/* Shared memory window length */
-	struct ewrk3_stats pktStats; /* Private stats counters */
-	u_char irq_mask;	/* Adapter IRQ mask bits */
-	u_char mPage;		/* Maximum 2kB Page number */
-	u_char lemac;		/* Chip rev. level */
-	u_char hard_strapped;	/* Don't allow a full open */
-	u_char txc;		/* Transmit cut through */
-	void __iomem *mctbl;	/* Pointer to the multicast table */
-	u_char led_mask;	/* Used to reserve LED access for ethtool */
-	spinlock_t hw_lock;
-};
-
-/*
-   ** Force the EtherWORKS 3 card to be in 2kB MODE
- */
-#define FORCE_2K_MODE { \
-  shmem_length = SHMEM_2K;\
-  outb(((mem_start - 0x80000) >> 11), EWRK3_MBR);\
-}
-
-/*
-   ** Public Functions
- */
-static int ewrk3_open(struct net_device *dev);
-static netdev_tx_t ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev);
-static irqreturn_t ewrk3_interrupt(int irq, void *dev_id);
-static int ewrk3_close(struct net_device *dev);
-static void set_multicast_list(struct net_device *dev);
-static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
-static const struct ethtool_ops ethtool_ops_203;
-static const struct ethtool_ops ethtool_ops;
-
-/*
-   ** Private functions
- */
-static int ewrk3_hw_init(struct net_device *dev, u_long iobase);
-static void ewrk3_init(struct net_device *dev);
-static int ewrk3_rx(struct net_device *dev);
-static int ewrk3_tx(struct net_device *dev);
-static void ewrk3_timeout(struct net_device *dev);
-
-static void EthwrkSignature(char *name, char *eeprom_image);
-static int DevicePresent(u_long iobase);
-static void SetMulticastFilter(struct net_device *dev);
-static int EISA_signature(char *name, s32 eisa_id);
-
-static int Read_EEPROM(u_long iobase, u_char eaddr);
-static int Write_EEPROM(short data, u_long iobase, u_char eaddr);
-static u_char get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType);
-
-static int ewrk3_probe1(struct net_device *dev, u_long iobase, int irq);
-static int isa_probe(struct net_device *dev, u_long iobase);
-static int eisa_probe(struct net_device *dev, u_long iobase);
-
-static u_char irq[MAX_NUM_EWRK3S+1] = {5, 0, 10, 3, 11, 9, 15, 12};
-
-static char name[EWRK3_STRLEN + 1];
-static int num_ewrks3s;
-
-/*
-   ** Miscellaneous defines...
- */
-#define INIT_EWRK3 {\
-    outb(EEPROM_INIT, EWRK3_IOPR);\
-    mdelay(1);\
-}
-
-#ifndef MODULE
-struct net_device * __init ewrk3_probe(int unit)
-{
-	struct net_device *dev = alloc_etherdev(sizeof(struct ewrk3_private));
-	int err;
-
-	if (!dev)
-		return ERR_PTR(-ENOMEM);
-
-	if (unit >= 0) {
-		sprintf(dev->name, "eth%d", unit);
-		netdev_boot_setup_check(dev);
-	}
-
-	err = ewrk3_probe1(dev, dev->base_addr, dev->irq);
-	if (err)
-		goto out;
-	return dev;
-out:
-	free_netdev(dev);
-	return ERR_PTR(err);
-
-}
-#endif
-
-static int __init ewrk3_probe1(struct net_device *dev, u_long iobase, int irq)
-{
-	int err;
-
-	dev->base_addr = iobase;
-	dev->irq = irq;
-
-	/* Address PROM pattern */
-	err = isa_probe(dev, iobase);
-	if (err != 0)
-		err = eisa_probe(dev, iobase);
-
-	if (err)
-		return err;
-
-	err = register_netdev(dev);
-	if (err)
-		release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
-
-	return err;
-}
-
-static const struct net_device_ops ewrk3_netdev_ops = {
-	.ndo_open		= ewrk3_open,
-	.ndo_start_xmit		= ewrk3_queue_pkt,
-	.ndo_stop		= ewrk3_close,
-	.ndo_set_multicast_list = set_multicast_list,
-	.ndo_do_ioctl		= ewrk3_ioctl,
-	.ndo_tx_timeout		= ewrk3_timeout,
-	.ndo_change_mtu		= eth_change_mtu,
-	.ndo_set_mac_address 	= eth_mac_addr,
-	.ndo_validate_addr	= eth_validate_addr,
-};
-
-static int __init
-ewrk3_hw_init(struct net_device *dev, u_long iobase)
-{
-	struct ewrk3_private *lp;
-	int i, status = 0;
-	u_long mem_start, shmem_length;
-	u_char cr, cmr, icr, nicsr, lemac, hard_strapped = 0;
-	u_char eeprom_image[EEPROM_MAX], chksum, eisa_cr = 0;
-
-	/*
-	** Stop the EWRK3. Enable the DBR ROM. Disable interrupts and remote boot.
-	** This also disables the EISA_ENABLE bit in the EISA Control Register.
-	 */
-	if (iobase > 0x400)
-		eisa_cr = inb(EISA_CR);
-	INIT_EWRK3;
-
-	nicsr = inb(EWRK3_CSR);
-
-	icr = inb(EWRK3_ICR);
-	icr &= 0x70;
-	outb(icr, EWRK3_ICR);	/* Disable all the IRQs */
-
-	if (nicsr != (CSR_TXD | CSR_RXD))
-		return -ENXIO;
-
-	/* Check that the EEPROM is alive and well and not living on Pluto... */
-	for (chksum = 0, i = 0; i < EEPROM_MAX; i += 2) {
-		union {
-			short val;
-			char c[2];
-		} tmp;
-
-		tmp.val = (short) Read_EEPROM(iobase, (i >> 1));
-		eeprom_image[i] = tmp.c[0];
-		eeprom_image[i + 1] = tmp.c[1];
-		chksum += eeprom_image[i] + eeprom_image[i + 1];
-	}
-
-	if (chksum != 0) {	/* Bad EEPROM Data! */
-		printk("%s: Device has a bad on-board EEPROM.\n", dev->name);
-		return -ENXIO;
-	}
-
-	EthwrkSignature(name, eeprom_image);
-	if (*name == '\0')
-		return -ENXIO;
-
-	dev->base_addr = iobase;
-
-	if (iobase > 0x400) {
-		outb(eisa_cr, EISA_CR);		/* Rewrite the EISA CR */
-	}
-	lemac = eeprom_image[EEPROM_CHIPVER];
-	cmr = inb(EWRK3_CMR);
-
-	if (((lemac == LeMAC) && ((cmr & CMR_NO_EEPROM) != CMR_NO_EEPROM)) ||
-	    ((lemac == LeMAC2) && !(cmr & CMR_HS))) {
-		printk("%s: %s at %#4lx", dev->name, name, iobase);
-		hard_strapped = 1;
-	} else if ((iobase & 0x0fff) == EWRK3_EISA_IO_PORTS) {
-		/* EISA slot address */
-		printk("%s: %s at %#4lx (EISA slot %ld)",
-		       dev->name, name, iobase, ((iobase >> 12) & 0x0f));
-	} else {	/* ISA port address */
-		printk("%s: %s at %#4lx", dev->name, name, iobase);
-	}
-
-	printk(", h/w address ");
-	if (lemac != LeMAC2)
-		DevicePresent(iobase);	/* need after EWRK3_INIT */
-	status = get_hw_addr(dev, eeprom_image, lemac);
-	printk("%pM\n", dev->dev_addr);
-
-	if (status) {
-		printk("      which has an EEPROM CRC error.\n");
-		return -ENXIO;
-	}
-
-	if (lemac == LeMAC2) {	/* Special LeMAC2 CMR things */
-		cmr &= ~(CMR_RA | CMR_WB | CMR_LINK | CMR_POLARITY | CMR_0WS);
-		if (eeprom_image[EEPROM_MISC0] & READ_AHEAD)
-			cmr |= CMR_RA;
-		if (eeprom_image[EEPROM_MISC0] & WRITE_BEHIND)
-			cmr |= CMR_WB;
-		if (eeprom_image[EEPROM_NETMAN0] & NETMAN_POL)
-			cmr |= CMR_POLARITY;
-		if (eeprom_image[EEPROM_NETMAN0] & NETMAN_LINK)
-			cmr |= CMR_LINK;
-		if (eeprom_image[EEPROM_MISC0] & _0WS_ENA)
-			cmr |= CMR_0WS;
-	}
-	if (eeprom_image[EEPROM_SETUP] & SETUP_DRAM)
-		cmr |= CMR_DRAM;
-	outb(cmr, EWRK3_CMR);
-
-	cr = inb(EWRK3_CR);	/* Set up the Control Register */
-	cr |= eeprom_image[EEPROM_SETUP] & SETUP_APD;
-	if (cr & SETUP_APD)
-		cr |= eeprom_image[EEPROM_SETUP] & SETUP_PS;
-	cr |= eeprom_image[EEPROM_MISC0] & FAST_BUS;
-	cr |= eeprom_image[EEPROM_MISC0] & ENA_16;
-	outb(cr, EWRK3_CR);
-
-	/*
-	** Determine the base address and window length for the EWRK3
-	** RAM from the memory base register.
-	*/
-	mem_start = inb(EWRK3_MBR);
-	shmem_length = 0;
-	if (mem_start != 0) {
-		if ((mem_start >= 0x0a) && (mem_start <= 0x0f)) {
-			mem_start *= SHMEM_64K;
-			shmem_length = SHMEM_64K;
-		} else if ((mem_start >= 0x14) && (mem_start <= 0x1f)) {
-			mem_start *= SHMEM_32K;
-			shmem_length = SHMEM_32K;
-		} else if ((mem_start >= 0x40) && (mem_start <= 0xff)) {
-			mem_start = mem_start * SHMEM_2K + 0x80000;
-			shmem_length = SHMEM_2K;
-		} else {
-			return -ENXIO;
-		}
-	}
-	/*
-	** See the top of this source code for comments about
-	** uncommenting this line.
-	*/
-/*          FORCE_2K_MODE; */
-
-	if (hard_strapped) {
-		printk("      is hard strapped.\n");
-	} else if (mem_start) {
-		printk("      has a %dk RAM window", (int) (shmem_length >> 10));
-		printk(" at 0x%.5lx", mem_start);
-	} else {
-		printk("      is in I/O only mode");
-	}
-
-	lp = netdev_priv(dev);
-	lp->shmem_base = mem_start;
-	lp->shmem = ioremap(mem_start, shmem_length);
-	if (!lp->shmem)
-		return -ENOMEM;
-	lp->shmem_length = shmem_length;
-	lp->lemac = lemac;
-	lp->hard_strapped = hard_strapped;
-	lp->led_mask = CR_LED;
-	spin_lock_init(&lp->hw_lock);
-
-	lp->mPage = 64;
-	if (cmr & CMR_DRAM)
-		lp->mPage <<= 1;	/* 2 DRAMS on module */
-
-	sprintf(lp->adapter_name, "%s (%s)", name, dev->name);
-
-	lp->irq_mask = ICR_TNEM | ICR_TXDM | ICR_RNEM | ICR_RXDM;
-
-	if (!hard_strapped) {
-		/*
-		** Enable EWRK3 board interrupts for autoprobing
-		*/
-		icr |= ICR_IE;	/* Enable interrupts */
-		outb(icr, EWRK3_ICR);
-
-		/* The DMA channel may be passed in on this parameter. */
-		dev->dma = 0;
-
-		/* To auto-IRQ we enable the initialization-done and DMA err,
-		   interrupts. For now we will always get a DMA error. */
-		if (dev->irq < 2) {
-#ifndef MODULE
-			u_char irqnum;
-			unsigned long irq_mask;
-
-
-			irq_mask = probe_irq_on();
-
-			/*
-			** Trigger a TNE interrupt.
-			*/
-			icr |= ICR_TNEM;
-			outb(1, EWRK3_TDQ);	/* Write to the TX done queue */
-			outb(icr, EWRK3_ICR);	/* Unmask the TXD interrupt */
-
-			irqnum = irq[((icr & IRQ_SEL) >> 4)];
-
-			mdelay(20);
-			dev->irq = probe_irq_off(irq_mask);
-			if ((dev->irq) && (irqnum == dev->irq)) {
-				printk(" and uses IRQ%d.\n", dev->irq);
-			} else {
-				if (!dev->irq) {
-					printk(" and failed to detect IRQ line.\n");
-				} else if ((irqnum == 1) && (lemac == LeMAC2)) {
-					printk(" and an illegal IRQ line detected.\n");
-				} else {
-					printk(", but incorrect IRQ line detected.\n");
-				}
-				iounmap(lp->shmem);
-				return -ENXIO;
-			}
-
-			DISABLE_IRQs;	/* Mask all interrupts */
-
-#endif				/* MODULE */
-		} else {
-			printk(" and requires IRQ%d.\n", dev->irq);
-		}
-	}
-
-	if (ewrk3_debug > 1) {
-		printk(version);
-	}
-	/* The EWRK3-specific entries in the device structure. */
-	dev->netdev_ops = &ewrk3_netdev_ops;
-	if (lp->adapter_name[4] == '3')
-		SET_ETHTOOL_OPS(dev, &ethtool_ops_203);
-	else
-		SET_ETHTOOL_OPS(dev, &ethtool_ops);
-	dev->watchdog_timeo = QUEUE_PKT_TIMEOUT;
-
-	dev->mem_start = 0;
-
-	return 0;
-}
-
-
-static int ewrk3_open(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_long iobase = dev->base_addr;
-	int status = 0;
-	u_char icr, csr;
-
-	/*
-	   ** Stop the TX and RX...
-	 */
-	STOP_EWRK3;
-
-	if (!lp->hard_strapped) {
-		if (request_irq(dev->irq, (void *) ewrk3_interrupt, 0, "ewrk3", dev)) {
-			printk("ewrk3_open(): Requested IRQ%d is busy\n", dev->irq);
-			status = -EAGAIN;
-		} else {
-
-			/*
-			   ** Re-initialize the EWRK3...
-			 */
-			ewrk3_init(dev);
-
-			if (ewrk3_debug > 1) {
-				printk("%s: ewrk3 open with irq %d\n", dev->name, dev->irq);
-				printk("  physical address: %pM\n", dev->dev_addr);
-				if (lp->shmem_length == 0) {
-					printk("  no shared memory, I/O only mode\n");
-				} else {
-					printk("  start of shared memory: 0x%08lx\n", lp->shmem_base);
-					printk("  window length: 0x%04lx\n", lp->shmem_length);
-				}
-				printk("  # of DRAMS: %d\n", ((inb(EWRK3_CMR) & 0x02) ? 2 : 1));
-				printk("  csr:  0x%02x\n", inb(EWRK3_CSR));
-				printk("  cr:   0x%02x\n", inb(EWRK3_CR));
-				printk("  icr:  0x%02x\n", inb(EWRK3_ICR));
-				printk("  cmr:  0x%02x\n", inb(EWRK3_CMR));
-				printk("  fmqc: 0x%02x\n", inb(EWRK3_FMQC));
-			}
-			netif_start_queue(dev);
-			/*
-			   ** Unmask EWRK3 board interrupts
-			 */
-			icr = inb(EWRK3_ICR);
-			ENABLE_IRQs;
-
-		}
-	} else {
-		printk(KERN_ERR "%s: ewrk3 available for hard strapped set up only.\n", dev->name);
-		printk(KERN_ERR "      Run the 'ewrk3setup' utility or remove the hard straps.\n");
-		return -EINVAL;
-	}
-
-	return status;
-}
-
-/*
-   ** Initialize the EtherWORKS 3 operating conditions
- */
-static void ewrk3_init(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_char csr, page;
-	u_long iobase = dev->base_addr;
-	int i;
-
-	/*
-	   ** Enable any multicasts
-	 */
-	set_multicast_list(dev);
-
-	/*
-	** Set hardware MAC address. Address is initialized from the EEPROM
-	** during startup but may have since been changed by the user.
-	*/
-	for (i=0; i<ETH_ALEN; i++)
-		outb(dev->dev_addr[i], EWRK3_PAR0 + i);
-
-	/*
-	   ** Clean out any remaining entries in all the queues here
-	 */
-	while (inb(EWRK3_TQ));
-	while (inb(EWRK3_TDQ));
-	while (inb(EWRK3_RQ));
-	while (inb(EWRK3_FMQ));
-
-	/*
-	   ** Write a clean free memory queue
-	 */
-	for (page = 1; page < lp->mPage; page++) {	/* Write the free page numbers */
-		outb(page, EWRK3_FMQ);	/* to the Free Memory Queue */
-	}
-
-	START_EWRK3;		/* Enable the TX and/or RX */
-}
-
-/*
- *  Transmit timeout
- */
-
-static void ewrk3_timeout(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_char icr, csr;
-	u_long iobase = dev->base_addr;
-
-	if (!lp->hard_strapped)
-	{
-		printk(KERN_WARNING"%s: transmit timed/locked out, status %04x, resetting.\n",
-		       dev->name, inb(EWRK3_CSR));
-
-		/*
-		   ** Mask all board interrupts
-		 */
-		DISABLE_IRQs;
-
-		/*
-		   ** Stop the TX and RX...
-		 */
-		STOP_EWRK3;
-
-		ewrk3_init(dev);
-
-		/*
-		   ** Unmask EWRK3 board interrupts
-		 */
-		ENABLE_IRQs;
-
-		dev->trans_start = jiffies; /* prevent tx timeout */
-		netif_wake_queue(dev);
-	}
-}
-
-/*
-   ** Writes a socket buffer to the free page queue
- */
-static netdev_tx_t ewrk3_queue_pkt(struct sk_buff *skb, struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_long iobase = dev->base_addr;
-	void __iomem *buf = NULL;
-	u_char icr;
-	u_char page;
-
-	spin_lock_irq (&lp->hw_lock);
-	DISABLE_IRQs;
-
-	/* if no resources available, exit, request packet be queued */
-	if (inb (EWRK3_FMQC) == 0) {
-		printk (KERN_WARNING "%s: ewrk3_queue_pkt(): No free resources...\n",
-			dev->name);
-		printk (KERN_WARNING "%s: ewrk3_queue_pkt(): CSR: %02x ICR: %02x FMQC: %02x\n",
-			dev->name, inb (EWRK3_CSR), inb (EWRK3_ICR),
-			inb (EWRK3_FMQC));
-		goto err_out;
-	}
-
-	/*
-	 ** Get a free page from the FMQ
-	 */
-	if ((page = inb (EWRK3_FMQ)) >= lp->mPage) {
-		printk ("ewrk3_queue_pkt(): Invalid free memory page (%d).\n",
-		     (u_char) page);
-		goto err_out;
-	}
-
-
-	/*
-	 ** Set up shared memory window and pointer into the window
-	 */
-	if (lp->shmem_length == IO_ONLY) {
-		outb (page, EWRK3_IOPR);
-	} else if (lp->shmem_length == SHMEM_2K) {
-		buf = lp->shmem;
-		outb (page, EWRK3_MPR);
-	} else if (lp->shmem_length == SHMEM_32K) {
-		buf = (((short) page << 11) & 0x7800) + lp->shmem;
-		outb ((page >> 4), EWRK3_MPR);
-	} else if (lp->shmem_length == SHMEM_64K) {
-		buf = (((short) page << 11) & 0xf800) + lp->shmem;
-		outb ((page >> 5), EWRK3_MPR);
-	} else {
-		printk (KERN_ERR "%s: Oops - your private data area is hosed!\n",
-			dev->name);
-		BUG ();
-	}
-
-	/*
-	 ** Set up the buffer control structures and copy the data from
-	 ** the socket buffer to the shared memory .
-	 */
-	if (lp->shmem_length == IO_ONLY) {
-		int i;
-		u_char *p = skb->data;
-		outb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), EWRK3_DATA);
-		outb ((char) (skb->len & 0xff), EWRK3_DATA);
-		outb ((char) ((skb->len >> 8) & 0xff), EWRK3_DATA);
-		outb ((char) 0x04, EWRK3_DATA);
-		for (i = 0; i < skb->len; i++) {
-			outb (*p++, EWRK3_DATA);
-		}
-		outb (page, EWRK3_TQ);	/* Start sending pkt */
-	} else {
-		writeb ((char) (TCR_QMODE | TCR_PAD | TCR_IFC), buf);	/* ctrl byte */
-		buf += 1;
-		writeb ((char) (skb->len & 0xff), buf);	/* length (16 bit xfer) */
-		buf += 1;
-		if (lp->txc) {
-			writeb(((skb->len >> 8) & 0xff) | XCT, buf);
-			buf += 1;
-			writeb (0x04, buf);	/* index byte */
-			buf += 1;
-			writeb (0x00, (buf + skb->len));	/* Write the XCT flag */
-			memcpy_toio (buf, skb->data, PRELOAD);	/* Write PRELOAD bytes */
-			outb (page, EWRK3_TQ);	/* Start sending pkt */
-			memcpy_toio (buf + PRELOAD,
-					 skb->data + PRELOAD,
-					 skb->len - PRELOAD);
-			writeb (0xff, (buf + skb->len));	/* Write the XCT flag */
-		} else {
-			writeb ((skb->len >> 8) & 0xff, buf);
-			buf += 1;
-			writeb (0x04, buf);	/* index byte */
-			buf += 1;
-			memcpy_toio (buf, skb->data, skb->len);	/* Write data bytes */
-			outb (page, EWRK3_TQ);	/* Start sending pkt */
-		}
-	}
-
-	ENABLE_IRQs;
-	spin_unlock_irq (&lp->hw_lock);
-
-	dev->stats.tx_bytes += skb->len;
-	dev_kfree_skb (skb);
-
-	/* Check for free resources: stop Tx queue if there are none */
-	if (inb (EWRK3_FMQC) == 0)
-		netif_stop_queue (dev);
-
-	return NETDEV_TX_OK;
-
-err_out:
-	ENABLE_IRQs;
-	spin_unlock_irq (&lp->hw_lock);
-	return NETDEV_TX_BUSY;
-}
-
-/*
-   ** The EWRK3 interrupt handler.
- */
-static irqreturn_t ewrk3_interrupt(int irq, void *dev_id)
-{
-	struct net_device *dev = dev_id;
-	struct ewrk3_private *lp;
-	u_long iobase;
-	u_char icr, cr, csr;
-
-	lp = netdev_priv(dev);
-	iobase = dev->base_addr;
-
-	/* get the interrupt information */
-	csr = inb(EWRK3_CSR);
-
-	/*
-	 ** Mask the EWRK3 board interrupts and turn on the LED
-	 */
-	spin_lock(&lp->hw_lock);
-	DISABLE_IRQs;
-
-	cr = inb(EWRK3_CR);
-	cr |= lp->led_mask;
-	outb(cr, EWRK3_CR);
-
-	if (csr & CSR_RNE)	/* Rx interrupt (packet[s] arrived) */
-		ewrk3_rx(dev);
-
-	if (csr & CSR_TNE)	/* Tx interrupt (packet sent) */
-		ewrk3_tx(dev);
-
-	/*
-	 ** Now deal with the TX/RX disable flags. These are set when there
-	 ** are no more resources. If resources free up then enable these
-	 ** interrupts, otherwise mask them - failure to do this will result
-	 ** in the system hanging in an interrupt loop.
-	 */
-	if (inb(EWRK3_FMQC)) {	/* any resources available? */
-		lp->irq_mask |= ICR_TXDM | ICR_RXDM;	/* enable the interrupt source */
-		csr &= ~(CSR_TXD | CSR_RXD);	/* ensure restart of a stalled TX or RX */
-		outb(csr, EWRK3_CSR);
-		netif_wake_queue(dev);
-	} else {
-		lp->irq_mask &= ~(ICR_TXDM | ICR_RXDM);		/* disable the interrupt source */
-	}
-
-	/* Unmask the EWRK3 board interrupts and turn off the LED */
-	cr &= ~(lp->led_mask);
-	outb(cr, EWRK3_CR);
-	ENABLE_IRQs;
-	spin_unlock(&lp->hw_lock);
-	return IRQ_HANDLED;
-}
-
-/* Called with lp->hw_lock held */
-static int ewrk3_rx(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_long iobase = dev->base_addr;
-	int i, status = 0;
-	u_char page;
-	void __iomem *buf = NULL;
-
-	while (inb(EWRK3_RQC) && !status) {	/* Whilst there's incoming data */
-		if ((page = inb(EWRK3_RQ)) < lp->mPage) {	/* Get next entry's buffer page */
-			/*
-			   ** Set up shared memory window and pointer into the window
-			 */
-			if (lp->shmem_length == IO_ONLY) {
-				outb(page, EWRK3_IOPR);
-			} else if (lp->shmem_length == SHMEM_2K) {
-				buf = lp->shmem;
-				outb(page, EWRK3_MPR);
-			} else if (lp->shmem_length == SHMEM_32K) {
-				buf = (((short) page << 11) & 0x7800) + lp->shmem;
-				outb((page >> 4), EWRK3_MPR);
-			} else if (lp->shmem_length == SHMEM_64K) {
-				buf = (((short) page << 11) & 0xf800) + lp->shmem;
-				outb((page >> 5), EWRK3_MPR);
-			} else {
-				status = -1;
-				printk("%s: Oops - your private data area is hosed!\n", dev->name);
-			}
-
-			if (!status) {
-				char rx_status;
-				int pkt_len;
-
-				if (lp->shmem_length == IO_ONLY) {
-					rx_status = inb(EWRK3_DATA);
-					pkt_len = inb(EWRK3_DATA);
-					pkt_len |= ((u_short) inb(EWRK3_DATA) << 8);
-				} else {
-					rx_status = readb(buf);
-					buf += 1;
-					pkt_len = readw(buf);
-					buf += 3;
-				}
-
-				if (!(rx_status & R_ROK)) {	/* There was an error. */
-					dev->stats.rx_errors++;	/* Update the error stats. */
-					if (rx_status & R_DBE)
-						dev->stats.rx_frame_errors++;
-					if (rx_status & R_CRC)
-						dev->stats.rx_crc_errors++;
-					if (rx_status & R_PLL)
-						dev->stats.rx_fifo_errors++;
-				} else {
-					struct sk_buff *skb;
-
-					if ((skb = dev_alloc_skb(pkt_len + 2)) != NULL) {
-						unsigned char *p;
-						skb_reserve(skb, 2);	/* Align to 16 bytes */
-						p = skb_put(skb, pkt_len);
-
-						if (lp->shmem_length == IO_ONLY) {
-							*p = inb(EWRK3_DATA);	/* dummy read */
-							for (i = 0; i < pkt_len; i++) {
-								*p++ = inb(EWRK3_DATA);
-							}
-						} else {
-							memcpy_fromio(p, buf, pkt_len);
-						}
-
-						for (i = 1; i < EWRK3_PKT_STAT_SZ - 1; i++) {
-							if (pkt_len < i * EWRK3_PKT_BIN_SZ) {
-								lp->pktStats.bins[i]++;
-								i = EWRK3_PKT_STAT_SZ;
-							}
-						}
-						p = skb->data;	/* Look at the dest addr */
-						if (is_multicast_ether_addr(p)) {
-							if (is_broadcast_ether_addr(p)) {
-								lp->pktStats.broadcast++;
-							} else {
-								lp->pktStats.multicast++;
-							}
-						} else if (compare_ether_addr(p, dev->dev_addr) == 0) {
-							lp->pktStats.unicast++;
-						}
-						lp->pktStats.bins[0]++;		/* Duplicates stats.rx_packets */
-						if (lp->pktStats.bins[0] == 0) {	/* Reset counters */
-							memset(&lp->pktStats, 0, sizeof(lp->pktStats));
-						}
-						/*
-						   ** Notify the upper protocol layers that there is another
-						   ** packet to handle
-						 */
-						skb->protocol = eth_type_trans(skb, dev);
-						netif_rx(skb);
-
-						/*
-						   ** Update stats
-						 */
-						dev->stats.rx_packets++;
-						dev->stats.rx_bytes += pkt_len;
-					} else {
-						printk("%s: Insufficient memory; nuking packet.\n", dev->name);
-						dev->stats.rx_dropped++;		/* Really, deferred. */
-						break;
-					}
-				}
-			}
-			/*
-			   ** Return the received buffer to the free memory queue
-			 */
-			outb(page, EWRK3_FMQ);
-		} else {
-			printk("ewrk3_rx(): Illegal page number, page %d\n", page);
-			printk("ewrk3_rx(): CSR: %02x ICR: %02x FMQC: %02x\n", inb(EWRK3_CSR), inb(EWRK3_ICR), inb(EWRK3_FMQC));
-		}
-	}
-	return status;
-}
-
-/*
-** Buffer sent - check for TX buffer errors.
-** Called with lp->hw_lock held
-*/
-static int ewrk3_tx(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_long iobase = dev->base_addr;
-	u_char tx_status;
-
-	while ((tx_status = inb(EWRK3_TDQ)) > 0) {	/* Whilst there's old buffers */
-		if (tx_status & T_VSTS) {	/* The status is valid */
-			if (tx_status & T_TXE) {
-				dev->stats.tx_errors++;
-				if (tx_status & T_NCL)
-					dev->stats.tx_carrier_errors++;
-				if (tx_status & T_LCL)
-					dev->stats.tx_window_errors++;
-				if (tx_status & T_CTU) {
-					if ((tx_status & T_COLL) ^ T_XUR) {
-						lp->pktStats.tx_underruns++;
-					} else {
-						lp->pktStats.excessive_underruns++;
-					}
-				} else if (tx_status & T_COLL) {
-					if ((tx_status & T_COLL) ^ T_XCOLL) {
-						dev->stats.collisions++;
-					} else {
-						lp->pktStats.excessive_collisions++;
-					}
-				}
-			} else {
-				dev->stats.tx_packets++;
-			}
-		}
-	}
-
-	return 0;
-}
-
-static int ewrk3_close(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_long iobase = dev->base_addr;
-	u_char icr, csr;
-
-	netif_stop_queue(dev);
-
-	if (ewrk3_debug > 1) {
-		printk("%s: Shutting down ethercard, status was %2.2x.\n",
-		       dev->name, inb(EWRK3_CSR));
-	}
-	/*
-	   ** We stop the EWRK3 here... mask interrupts and stop TX & RX
-	 */
-	DISABLE_IRQs;
-
-	STOP_EWRK3;
-
-	/*
-	   ** Clean out the TX and RX queues here (note that one entry
-	   ** may get added to either the TXD or RX queues if the TX or RX
-	   ** just starts processing a packet before the STOP_EWRK3 command
-	   ** is received. This will be flushed in the ewrk3_open() call).
-	 */
-	while (inb(EWRK3_TQ));
-	while (inb(EWRK3_TDQ));
-	while (inb(EWRK3_RQ));
-
-	if (!lp->hard_strapped) {
-		free_irq(dev->irq, dev);
-	}
-	return 0;
-}
-
-/*
-   ** Set or clear the multicast filter for this adapter.
- */
-static void set_multicast_list(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	u_long iobase = dev->base_addr;
-	u_char csr;
-
-	csr = inb(EWRK3_CSR);
-
-	if (lp->shmem_length == IO_ONLY) {
-		lp->mctbl = NULL;
-	} else {
-		lp->mctbl = lp->shmem + PAGE0_HTE;
-	}
-
-	csr &= ~(CSR_PME | CSR_MCE);
-	if (dev->flags & IFF_PROMISC) {		/* set promiscuous mode */
-		csr |= CSR_PME;
-		outb(csr, EWRK3_CSR);
-	} else {
-		SetMulticastFilter(dev);
-		csr |= CSR_MCE;
-		outb(csr, EWRK3_CSR);
-	}
-}
-
-/*
-   ** Calculate the hash code and update the logical address filter
-   ** from a list of ethernet multicast addresses.
-   ** Little endian crc one liner from Matt Thomas, DEC.
-   **
-   ** Note that when clearing the table, the broadcast bit must remain asserted
-   ** to receive broadcast messages.
- */
-static void SetMulticastFilter(struct net_device *dev)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	struct netdev_hw_addr *ha;
-	u_long iobase = dev->base_addr;
-	int i;
-	char bit, byte;
-	short __iomem *p = lp->mctbl;
-	u16 hashcode;
-	u32 crc;
-
-	spin_lock_irq(&lp->hw_lock);
-
-	if (lp->shmem_length == IO_ONLY) {
-		outb(0, EWRK3_IOPR);
-		outw(PAGE0_HTE, EWRK3_PIR1);
-	} else {
-		outb(0, EWRK3_MPR);
-	}
-
-	if (dev->flags & IFF_ALLMULTI) {
-		for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
-			if (lp->shmem_length == IO_ONLY) {
-				outb(0xff, EWRK3_DATA);
-			} else {	/* memset didn't work here */
-				writew(0xffff, p);
-				p++;
-				i++;
-			}
-		}
-	} else {
-		/* Clear table except for broadcast bit */
-		if (lp->shmem_length == IO_ONLY) {
-			for (i = 0; i < (HASH_TABLE_LEN >> 4) - 1; i++) {
-				outb(0x00, EWRK3_DATA);
-			}
-			outb(0x80, EWRK3_DATA);
-			i++;	/* insert the broadcast bit */
-			for (; i < (HASH_TABLE_LEN >> 3); i++) {
-				outb(0x00, EWRK3_DATA);
-			}
-		} else {
-			memset_io(lp->mctbl, 0, HASH_TABLE_LEN >> 3);
-			writeb(0x80, lp->mctbl + (HASH_TABLE_LEN >> 4) - 1);
-		}
-
-		/* Update table */
-		netdev_for_each_mc_addr(ha, dev) {
-			crc = ether_crc_le(ETH_ALEN, ha->addr);
-			hashcode = crc & ((1 << 9) - 1);	/* hashcode is 9 LSb of CRC */
-
-			byte = hashcode >> 3;	/* bit[3-8] -> byte in filter */
-			bit = 1 << (hashcode & 0x07);	/* bit[0-2] -> bit in byte */
-
-			if (lp->shmem_length == IO_ONLY) {
-				u_char tmp;
-
-				outw(PAGE0_HTE + byte, EWRK3_PIR1);
-				tmp = inb(EWRK3_DATA);
-				tmp |= bit;
-				outw(PAGE0_HTE + byte, EWRK3_PIR1);
-				outb(tmp, EWRK3_DATA);
-			} else {
-				writeb(readb(lp->mctbl + byte) | bit, lp->mctbl + byte);
-			}
-		}
-	}
-
-	spin_unlock_irq(&lp->hw_lock);
-}
-
-/*
-   ** ISA bus I/O device probe
- */
-static int __init isa_probe(struct net_device *dev, u_long ioaddr)
-{
-	int i = num_ewrks3s, maxSlots;
-	int ret = -ENODEV;
-
-	u_long iobase;
-
-	if (ioaddr >= 0x400)
-		goto out;
-
-	if (ioaddr == 0) {	/* Autoprobing */
-		iobase = EWRK3_IO_BASE;		/* Get the first slot address */
-		maxSlots = 24;
-	} else {		/* Probe a specific location */
-		iobase = ioaddr;
-		maxSlots = i + 1;
-	}
-
-	for (; (i < maxSlots) && (dev != NULL);
-	     iobase += EWRK3_IOP_INC, i++)
-	{
-		if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME)) {
-			if (DevicePresent(iobase) == 0) {
-				int irq = dev->irq;
-				ret = ewrk3_hw_init(dev, iobase);
-				if (!ret)
-					break;
-				dev->irq = irq;
-			}
-			release_region(iobase, EWRK3_TOTAL_SIZE);
-		}
-	}
- out:
-
-	return ret;
-}
-
-/*
-   ** EISA bus I/O device probe. Probe from slot 1 since slot 0 is usually
-   ** the motherboard.
- */
-static int __init eisa_probe(struct net_device *dev, u_long ioaddr)
-{
-	int i, maxSlots;
-	u_long iobase;
-	int ret = -ENODEV;
-
-	if (ioaddr < 0x1000)
-		goto out;
-
-	iobase = ioaddr;
-	i = (ioaddr >> 12);
-	maxSlots = i + 1;
-
-	for (i = 1; (i < maxSlots) && (dev != NULL); i++, iobase += EISA_SLOT_INC) {
-		if (EISA_signature(name, EISA_ID) == 0) {
-			if (request_region(iobase, EWRK3_TOTAL_SIZE, DRV_NAME) &&
-			    DevicePresent(iobase) == 0) {
-				int irq = dev->irq;
-				ret = ewrk3_hw_init(dev, iobase);
-				if (!ret)
-					break;
-				dev->irq = irq;
-			}
-			release_region(iobase, EWRK3_TOTAL_SIZE);
-		}
-	}
-
- out:
-	return ret;
-}
-
-
-/*
-   ** Read the EWRK3 EEPROM using this routine
- */
-static int Read_EEPROM(u_long iobase, u_char eaddr)
-{
-	int i;
-
-	outb((eaddr & 0x3f), EWRK3_PIR1);	/* set up 6 bits of address info */
-	outb(EEPROM_RD, EWRK3_IOPR);	/* issue read command */
-	for (i = 0; i < 5000; i++)
-		inb(EWRK3_CSR);	/* wait 1msec */
-
-	return inw(EWRK3_EPROM1);	/* 16 bits data return */
-}
-
-/*
-   ** Write the EWRK3 EEPROM using this routine
- */
-static int Write_EEPROM(short data, u_long iobase, u_char eaddr)
-{
-	int i;
-
-	outb(EEPROM_WR_EN, EWRK3_IOPR);		/* issue write enable command */
-	for (i = 0; i < 5000; i++)
-		inb(EWRK3_CSR);	/* wait 1msec */
-	outw(data, EWRK3_EPROM1);	/* write data to register */
-	outb((eaddr & 0x3f), EWRK3_PIR1);	/* set up 6 bits of address info */
-	outb(EEPROM_WR, EWRK3_IOPR);	/* issue write command */
-	for (i = 0; i < 75000; i++)
-		inb(EWRK3_CSR);	/* wait 15msec */
-	outb(EEPROM_WR_DIS, EWRK3_IOPR);	/* issue write disable command */
-	for (i = 0; i < 5000; i++)
-		inb(EWRK3_CSR);	/* wait 1msec */
-
-	return 0;
-}
-
-/*
-   ** Look for a particular board name in the on-board EEPROM.
- */
-static void __init EthwrkSignature(char *name, char *eeprom_image)
-{
-	int i;
-	char *signatures[] = EWRK3_SIGNATURE;
-
-	for (i=0; *signatures[i] != '\0'; i++)
-		if( !strncmp(eeprom_image+EEPROM_PNAME7, signatures[i], strlen(signatures[i])) )
-			break;
-
-	if (*signatures[i] != '\0') {
-		memcpy(name, eeprom_image+EEPROM_PNAME7, EWRK3_STRLEN);
-		name[EWRK3_STRLEN] = '\0';
-	} else
-		name[0] = '\0';
-}
-
-/*
-   ** Look for a special sequence in the Ethernet station address PROM that
-   ** is common across all EWRK3 products.
-   **
-   ** Search the Ethernet address ROM for the signature. Since the ROM address
-   ** counter can start at an arbitrary point, the search must include the entire
-   ** probe sequence length plus the (length_of_the_signature - 1).
-   ** Stop the search IMMEDIATELY after the signature is found so that the
-   ** PROM address counter is correctly positioned at the start of the
-   ** ethernet address for later read out.
- */
-
-static int __init DevicePresent(u_long iobase)
-{
-	union {
-		struct {
-			u32 a;
-			u32 b;
-		} llsig;
-		char Sig[sizeof(u32) << 1];
-	}
-	dev;
-	short sigLength;
-	char data;
-	int i, j, status = 0;
-
-	dev.llsig.a = ETH_PROM_SIG;
-	dev.llsig.b = ETH_PROM_SIG;
-	sigLength = sizeof(u32) << 1;
-
-	for (i = 0, j = 0; j < sigLength && i < PROBE_LENGTH + sigLength - 1; i++) {
-		data = inb(EWRK3_APROM);
-		if (dev.Sig[j] == data) {	/* track signature */
-			j++;
-		} else {	/* lost signature; begin search again */
-			if (data == dev.Sig[0]) {
-				j = 1;
-			} else {
-				j = 0;
-			}
-		}
-	}
-
-	if (j != sigLength) {
-		status = -ENODEV;	/* search failed */
-	}
-	return status;
-}
-
-static u_char __init get_hw_addr(struct net_device *dev, u_char * eeprom_image, char chipType)
-{
-	int i, j, k;
-	u_short chksum;
-	u_char crc, lfsr, sd, status = 0;
-	u_long iobase = dev->base_addr;
-	u16 tmp;
-
-	if (chipType == LeMAC2) {
-		for (crc = 0x6a, j = 0; j < ETH_ALEN; j++) {
-			sd = dev->dev_addr[j] = eeprom_image[EEPROM_PADDR0 + j];
-			outb(dev->dev_addr[j], EWRK3_PAR0 + j);
-			for (k = 0; k < 8; k++, sd >>= 1) {
-				lfsr = ((((crc & 0x02) >> 1) ^ (crc & 0x01)) ^ (sd & 0x01)) << 7;
-				crc = (crc >> 1) + lfsr;
-			}
-		}
-		if (crc != eeprom_image[EEPROM_PA_CRC])
-			status = -1;
-	} else {
-		for (i = 0, k = 0; i < ETH_ALEN;) {
-			k <<= 1;
-			if (k > 0xffff)
-				k -= 0xffff;
-
-			k += (u_char) (tmp = inb(EWRK3_APROM));
-			dev->dev_addr[i] = (u_char) tmp;
-			outb(dev->dev_addr[i], EWRK3_PAR0 + i);
-			i++;
-			k += (u_short) ((tmp = inb(EWRK3_APROM)) << 8);
-			dev->dev_addr[i] = (u_char) tmp;
-			outb(dev->dev_addr[i], EWRK3_PAR0 + i);
-			i++;
-
-			if (k > 0xffff)
-				k -= 0xffff;
-		}
-		if (k == 0xffff)
-			k = 0;
-		chksum = inb(EWRK3_APROM);
-		chksum |= (inb(EWRK3_APROM) << 8);
-		if (k != chksum)
-			status = -1;
-	}
-
-	return status;
-}
-
-/*
-   ** Look for a particular board name in the EISA configuration space
- */
-static int __init EISA_signature(char *name, s32 eisa_id)
-{
-	u_long i;
-	char *signatures[] = EWRK3_SIGNATURE;
-	char ManCode[EWRK3_STRLEN];
-	union {
-		s32 ID;
-		char Id[4];
-	} Eisa;
-	int status = 0;
-
-	*name = '\0';
-	for (i = 0; i < 4; i++) {
-		Eisa.Id[i] = inb(eisa_id + i);
-	}
-
-	ManCode[0] = (((Eisa.Id[0] >> 2) & 0x1f) + 0x40);
-	ManCode[1] = (((Eisa.Id[1] & 0xe0) >> 5) + ((Eisa.Id[0] & 0x03) << 3) + 0x40);
-	ManCode[2] = (((Eisa.Id[2] >> 4) & 0x0f) + 0x30);
-	ManCode[3] = ((Eisa.Id[2] & 0x0f) + 0x30);
-	ManCode[4] = (((Eisa.Id[3] >> 4) & 0x0f) + 0x30);
-	ManCode[5] = '\0';
-
-	for (i = 0; (*signatures[i] != '\0') && (*name == '\0'); i++) {
-		if (strstr(ManCode, signatures[i]) != NULL) {
-			strcpy(name, ManCode);
-			status = 1;
-		}
-	}
-
-	return status;		/* return the device name string */
-}
-
-static void ewrk3_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info)
-{
-	int fwrev = Read_EEPROM(dev->base_addr, EEPROM_REVLVL);
-
-	strcpy(info->driver, DRV_NAME);
-	strcpy(info->version, DRV_VERSION);
-	sprintf(info->fw_version, "%d", fwrev);
-	strcpy(info->bus_info, "N/A");
-	info->eedump_len = EEPROM_MAX;
-}
-
-static int ewrk3_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	unsigned long iobase = dev->base_addr;
-	u8 cr = inb(EWRK3_CR);
-
-	switch (lp->adapter_name[4]) {
-	case '3': /* DE203 */
-		ecmd->supported = SUPPORTED_BNC;
-		ecmd->port = PORT_BNC;
-		break;
-
-	case '4': /* DE204 */
-		ecmd->supported = SUPPORTED_TP;
-		ecmd->port = PORT_TP;
-		break;
-
-	case '5': /* DE205 */
-		ecmd->supported = SUPPORTED_TP | SUPPORTED_BNC | SUPPORTED_AUI;
-		ecmd->autoneg = !(cr & CR_APD);
-		/*
-		** Port is only valid if autoneg is disabled
-		** and even then we don't know if AUI is jumpered.
-		*/
-		if (!ecmd->autoneg)
-			ecmd->port = (cr & CR_PSEL) ? PORT_BNC : PORT_TP;
-		break;
-	}
-
-	ecmd->supported |= SUPPORTED_10baseT_Half;
-	ethtool_cmd_speed_set(ecmd, SPEED_10);
-	ecmd->duplex = DUPLEX_HALF;
-	return 0;
-}
-
-static int ewrk3_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	unsigned long iobase = dev->base_addr;
-	unsigned long flags;
-	u8 cr;
-
-	/* DE205 is the only card with anything to set */
-	if (lp->adapter_name[4] != '5')
-		return -EOPNOTSUPP;
-
-	/* Sanity-check parameters */
-	if (ecmd->speed != SPEED_10)
-		return -EINVAL;
-	if (ecmd->port != PORT_TP && ecmd->port != PORT_BNC)
-		return -EINVAL; /* AUI is not software-selectable */
-	if (ecmd->transceiver != XCVR_INTERNAL)
-		return -EINVAL;
-	if (ecmd->duplex != DUPLEX_HALF)
-		return -EINVAL;
-	if (ecmd->phy_address != 0)
-		return -EINVAL;
-
-	spin_lock_irqsave(&lp->hw_lock, flags);
-	cr = inb(EWRK3_CR);
-
-	/* If Autoneg is set, change to Auto Port mode */
-	/* Otherwise, disable Auto Port and set port explicitly */
-	if (ecmd->autoneg) {
-		cr &= ~CR_APD;
-	} else {
-		cr |= CR_APD;
-		if (ecmd->port == PORT_TP)
-			cr &= ~CR_PSEL;		/* Force TP */
-		else
-			cr |= CR_PSEL;		/* Force BNC */
-	}
-
-	/* Commit the changes */
-	outb(cr, EWRK3_CR);
-	spin_unlock_irqrestore(&lp->hw_lock, flags);
-	return 0;
-}
-
-static u32 ewrk3_get_link(struct net_device *dev)
-{
-	unsigned long iobase = dev->base_addr;
-	u8 cmr = inb(EWRK3_CMR);
-	/* DE203 has BNC only and link status does not apply */
-	/* On DE204 this is always valid since TP is the only port. */
-	/* On DE205 this reflects TP status even if BNC or AUI is selected. */
-	return !(cmr & CMR_LINK);
-}
-
-static int ewrk3_set_phys_id(struct net_device *dev,
-			     enum ethtool_phys_id_state state)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	unsigned long iobase = dev->base_addr;
-	u8 cr;
-
-	spin_lock_irq(&lp->hw_lock);
-
-	switch (state) {
-	case ETHTOOL_ID_ACTIVE:
-		/* Prevent ISR from twiddling the LED */
-		lp->led_mask = 0;
-		spin_unlock_irq(&lp->hw_lock);
-		return 2;	/* cycle on/off twice per second */
-
-	case ETHTOOL_ID_ON:
-		cr = inb(EWRK3_CR);
-		outb(cr | CR_LED, EWRK3_CR);
-		break;
-
-	case ETHTOOL_ID_OFF:
-		cr = inb(EWRK3_CR);
-		outb(cr & ~CR_LED, EWRK3_CR);
-		break;
-
-	case ETHTOOL_ID_INACTIVE:
-		lp->led_mask = CR_LED;
-		cr = inb(EWRK3_CR);
-		outb(cr & ~CR_LED, EWRK3_CR);
-	}
-	spin_unlock_irq(&lp->hw_lock);
-
-	return 0;
-}
-
-static const struct ethtool_ops ethtool_ops_203 = {
-	.get_drvinfo = ewrk3_get_drvinfo,
-	.get_settings = ewrk3_get_settings,
-	.set_settings = ewrk3_set_settings,
-	.set_phys_id = ewrk3_set_phys_id,
-};
-
-static const struct ethtool_ops ethtool_ops = {
-	.get_drvinfo = ewrk3_get_drvinfo,
-	.get_settings = ewrk3_get_settings,
-	.set_settings = ewrk3_set_settings,
-	.get_link = ewrk3_get_link,
-	.set_phys_id = ewrk3_set_phys_id,
-};
-
-/*
-   ** Perform IOCTL call functions here. Some are privileged operations and the
-   ** effective uid is checked in those cases.
- */
-static int ewrk3_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-{
-	struct ewrk3_private *lp = netdev_priv(dev);
-	struct ewrk3_ioctl *ioc = (struct ewrk3_ioctl *) &rq->ifr_ifru;
-	u_long iobase = dev->base_addr;
-	int i, j, status = 0;
-	u_char csr;
-	unsigned long flags;
-	union ewrk3_addr {
-		u_char addr[HASH_TABLE_LEN * ETH_ALEN];
-		u_short val[(HASH_TABLE_LEN * ETH_ALEN) >> 1];
-	};
-
-	union ewrk3_addr *tmp;
-
-	/* All we handle are private IOCTLs */
-	if (cmd != EWRK3IOCTL)
-		return -EOPNOTSUPP;
-
-	tmp = kmalloc(sizeof(union ewrk3_addr), GFP_KERNEL);
-	if(tmp==NULL)
-		return -ENOMEM;
-
-	switch (ioc->cmd) {
-	case EWRK3_GET_HWADDR:	/* Get the hardware address */
-		for (i = 0; i < ETH_ALEN; i++) {
-			tmp->addr[i] = dev->dev_addr[i];
-		}
-		ioc->len = ETH_ALEN;
-		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
-			status = -EFAULT;
-		break;
-
-	case EWRK3_SET_HWADDR:	/* Set the hardware address */
-		if (capable(CAP_NET_ADMIN)) {
-			spin_lock_irqsave(&lp->hw_lock, flags);
-			csr = inb(EWRK3_CSR);
-			csr |= (CSR_TXD | CSR_RXD);
-			outb(csr, EWRK3_CSR);	/* Disable the TX and RX */
-			spin_unlock_irqrestore(&lp->hw_lock, flags);
-
-			if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN)) {
-				status = -EFAULT;
-				break;
-			}
-			spin_lock_irqsave(&lp->hw_lock, flags);
-			for (i = 0; i < ETH_ALEN; i++) {
-				dev->dev_addr[i] = tmp->addr[i];
-				outb(tmp->addr[i], EWRK3_PAR0 + i);
-			}
-
-			csr = inb(EWRK3_CSR);
-			csr &= ~(CSR_TXD | CSR_RXD);	/* Enable the TX and RX */
-			outb(csr, EWRK3_CSR);
-			spin_unlock_irqrestore(&lp->hw_lock, flags);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_SET_PROM:	/* Set Promiscuous Mode */
-		if (capable(CAP_NET_ADMIN)) {
-			spin_lock_irqsave(&lp->hw_lock, flags);
-			csr = inb(EWRK3_CSR);
-			csr |= CSR_PME;
-			csr &= ~CSR_MCE;
-			outb(csr, EWRK3_CSR);
-			spin_unlock_irqrestore(&lp->hw_lock, flags);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_CLR_PROM:	/* Clear Promiscuous Mode */
-		if (capable(CAP_NET_ADMIN)) {
-			spin_lock_irqsave(&lp->hw_lock, flags);
-			csr = inb(EWRK3_CSR);
-			csr &= ~CSR_PME;
-			outb(csr, EWRK3_CSR);
-			spin_unlock_irqrestore(&lp->hw_lock, flags);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_GET_MCA:	/* Get the multicast address table */
-		spin_lock_irqsave(&lp->hw_lock, flags);
-		if (lp->shmem_length == IO_ONLY) {
-			outb(0, EWRK3_IOPR);
-			outw(PAGE0_HTE, EWRK3_PIR1);
-			for (i = 0; i < (HASH_TABLE_LEN >> 3); i++) {
-				tmp->addr[i] = inb(EWRK3_DATA);
-			}
-		} else {
-			outb(0, EWRK3_MPR);
-			memcpy_fromio(tmp->addr, lp->shmem + PAGE0_HTE, (HASH_TABLE_LEN >> 3));
-		}
-		spin_unlock_irqrestore(&lp->hw_lock, flags);
-
-		ioc->len = (HASH_TABLE_LEN >> 3);
-		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
-			status = -EFAULT;
-
-		break;
-	case EWRK3_SET_MCA:	/* Set a multicast address */
-		if (capable(CAP_NET_ADMIN)) {
-			if (ioc->len > HASH_TABLE_LEN) {
-				status = -EINVAL;
-				break;
-			}
-			if (copy_from_user(tmp->addr, ioc->data, ETH_ALEN * ioc->len)) {
-				status = -EFAULT;
-				break;
-			}
-			set_multicast_list(dev);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_CLR_MCA:	/* Clear all multicast addresses */
-		if (capable(CAP_NET_ADMIN)) {
-			set_multicast_list(dev);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_MCA_EN:	/* Enable multicast addressing */
-		if (capable(CAP_NET_ADMIN)) {
-			spin_lock_irqsave(&lp->hw_lock, flags);
-			csr = inb(EWRK3_CSR);
-			csr |= CSR_MCE;
-			csr &= ~CSR_PME;
-			outb(csr, EWRK3_CSR);
-			spin_unlock_irqrestore(&lp->hw_lock, flags);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_GET_STATS: { /* Get the driver statistics */
-		struct ewrk3_stats *tmp_stats =
-        		kmalloc(sizeof(lp->pktStats), GFP_KERNEL);
-		if (!tmp_stats) {
-			status = -ENOMEM;
-			break;
-		}
-
-		spin_lock_irqsave(&lp->hw_lock, flags);
-		memcpy(tmp_stats, &lp->pktStats, sizeof(lp->pktStats));
-		spin_unlock_irqrestore(&lp->hw_lock, flags);
-
-		ioc->len = sizeof(lp->pktStats);
-		if (copy_to_user(ioc->data, tmp_stats, sizeof(lp->pktStats)))
-    			status = -EFAULT;
-		kfree(tmp_stats);
-		break;
-	}
-	case EWRK3_CLR_STATS:	/* Zero out the driver statistics */
-		if (capable(CAP_NET_ADMIN)) {
-			spin_lock_irqsave(&lp->hw_lock, flags);
-			memset(&lp->pktStats, 0, sizeof(lp->pktStats));
-			spin_unlock_irqrestore(&lp->hw_lock,flags);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_GET_CSR:	/* Get the CSR Register contents */
-		tmp->addr[0] = inb(EWRK3_CSR);
-		ioc->len = 1;
-		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
-			status = -EFAULT;
-		break;
-	case EWRK3_SET_CSR:	/* Set the CSR Register contents */
-		if (capable(CAP_NET_ADMIN)) {
-			if (copy_from_user(tmp->addr, ioc->data, 1)) {
-				status = -EFAULT;
-				break;
-			}
-			outb(tmp->addr[0], EWRK3_CSR);
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_GET_EEPROM:	/* Get the EEPROM contents */
-		if (capable(CAP_NET_ADMIN)) {
-			for (i = 0; i < (EEPROM_MAX >> 1); i++) {
-				tmp->val[i] = (short) Read_EEPROM(iobase, i);
-			}
-			i = EEPROM_MAX;
-			tmp->addr[i++] = inb(EWRK3_CMR);		/* Config/Management Reg. */
-			for (j = 0; j < ETH_ALEN; j++) {
-				tmp->addr[i++] = inb(EWRK3_PAR0 + j);
-			}
-			ioc->len = EEPROM_MAX + 1 + ETH_ALEN;
-			if (copy_to_user(ioc->data, tmp->addr, ioc->len))
-				status = -EFAULT;
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_SET_EEPROM:	/* Set the EEPROM contents */
-		if (capable(CAP_NET_ADMIN)) {
-			if (copy_from_user(tmp->addr, ioc->data, EEPROM_MAX)) {
-				status = -EFAULT;
-				break;
-			}
-			for (i = 0; i < (EEPROM_MAX >> 1); i++) {
-				Write_EEPROM(tmp->val[i], iobase, i);
-			}
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_GET_CMR:	/* Get the CMR Register contents */
-		tmp->addr[0] = inb(EWRK3_CMR);
-		ioc->len = 1;
-		if (copy_to_user(ioc->data, tmp->addr, ioc->len))
-			status = -EFAULT;
-		break;
-	case EWRK3_SET_TX_CUT_THRU:	/* Set TX cut through mode */
-		if (capable(CAP_NET_ADMIN)) {
-			lp->txc = 1;
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	case EWRK3_CLR_TX_CUT_THRU:	/* Clear TX cut through mode */
-		if (capable(CAP_NET_ADMIN)) {
-			lp->txc = 0;
-		} else {
-			status = -EPERM;
-		}
-
-		break;
-	default:
-		status = -EOPNOTSUPP;
-	}
-	kfree(tmp);
-	return status;
-}
-
-#ifdef MODULE
-static struct net_device *ewrk3_devs[MAX_NUM_EWRK3S];
-static int ndevs;
-static int io[MAX_NUM_EWRK3S+1] = { 0x300, 0, };
-
-/* '21' below should really be 'MAX_NUM_EWRK3S' */
-module_param_array(io, int, NULL, 0);
-module_param_array(irq, int, NULL, 0);
-MODULE_PARM_DESC(io, "EtherWORKS 3 I/O base address(es)");
-MODULE_PARM_DESC(irq, "EtherWORKS 3 IRQ number(s)");
-
-static __exit void ewrk3_exit_module(void)
-{
-	int i;
-
-	for( i=0; i<ndevs; i++ ) {
-		struct net_device *dev = ewrk3_devs[i];
-		struct ewrk3_private *lp = netdev_priv(dev);
-		ewrk3_devs[i] = NULL;
-		unregister_netdev(dev);
-		release_region(dev->base_addr, EWRK3_TOTAL_SIZE);
-		iounmap(lp->shmem);
-		free_netdev(dev);
-	}
-}
-
-static __init int ewrk3_init_module(void)
-{
-	int i=0;
-
-	while( io[i] && irq[i] ) {
-		struct net_device *dev
-			= alloc_etherdev(sizeof(struct ewrk3_private));
-
-		if (!dev)
-			break;
-
-		if (ewrk3_probe1(dev, io[i], irq[i]) != 0) {
-			free_netdev(dev);
-			break;
-		}
-
-		ewrk3_devs[ndevs++] = dev;
-		i++;
-	}
-
-	return ndevs ? 0 : -EIO;
-}
-
-
-/* Hack for breakage in new module stuff */
-module_exit(ewrk3_exit_module);
-module_init(ewrk3_init_module);
-#endif				/* MODULE */
-MODULE_LICENSE("GPL");