[PATCH] libertas: Purge non-mesh ioctls

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

1 files changed, 0 insertions, 516 deletions

diff --git a/drivers/net/wireless/libertas/README b/drivers/net/wireless/libertas/README
index 688da4c784b1..378577200b56 100644
--- a/drivers/net/wireless/libertas/README
+++ b/drivers/net/wireless/libertas/README
@@ -40,64 +40,11 @@ NAME
 SYNOPSIS
 	iwpriv <ethX> <command> [sub-command] ...
 
-	iwpriv ethX version
-	iwpriv ethX scantype [sub-command]
-	iwpriv ethX getSNR <n>
-	iwpriv ethX getNF <n>
-	iwpriv ethX getRSSI <n>
-	iwpriv ethX setrxant <n>
-	iwpriv ethX getrxant
-	iwpriv ethX settxant <n>
-	iwpriv ethX gettxant
-	iwpriv ethX authalgs <n>
-	iwpriv ethX pre-TBTT <n>
-	iwpriv ethX 8021xauthalgs <n>
-	iwpriv ethX encryptionmode <n>
 	iwpriv ethX setregioncode <n>
 	iwpriv ethX getregioncode
-	iwpriv ethX setbcnavg <n>
-	iwpriv ethX getbcnavg
-	iwpriv ethX setdataavg <n>
-	iwpriv ethX setlisteninter <n>
-	iwpriv ethX getlisteninter
-	iwpriv ethX setmultipledtim <n>
-	iwpriv ethX getmultipledtim
-	iwpriv ethX atimwindow <n>
-	iwpriv ethX deauth
-	iwpriv ethX adhocstop
-	iwpriv ethX radioon
-	iwpriv ethX radiooff
-	iwpriv ethX reasso-on
-	iwpriv ethX reasso-off
-	iwpriv ethX scanmode  [sub-command]
-	iwpriv ethX setwpaie <n>
-	iwpriv ethX wlanidle-off
-	iwpriv ethX wlanidle-on
-	iwpriv ethX getcis
-	iwpriv ethX getlog
-	iwpriv ethX getadhocstatus
-	iwpriv ethX adhocgrate <n>
-
-Version 4 Command:
-	iwpriv ethX inactvityto <n>
-	iwpriv ethX sleeppd <n>
-	iwpriv ethX enable11d <n>
-	iwpriv ethX tpccfg <n>
-	iwpriv ethX powercfg <n>
-	iwpriv ethX setafc <n>
-	iwpriv ethX getafc
 
 Version 5 Command:
 	iwpriv ethX ledgpio <n>
-	iwpriv ethX scanprobes <n>
-	iwpriv ethX lolisteninter <n>
-	iwpriv ethX rateadapt <n> <m>
-	iwpriv ethX txcontrol <n>
-	iwpriv ethX psnullinterval <n>
-	iwpriv ethX prescan <n>
-	iwpriv ethX getrxinfo
-	iwpriv ethX gettxrate
-	iwpriv ethX beaconinterval
 
 BT Commands:
 	The blinding table (BT) contains a list of mac addresses that should be
@@ -150,114 +97,6 @@ DESCRIPTION
 	The ethX parameter specifies the network device that is to be used to
 		perform this command on. it could be eth0, eth1 etc.
 
-version
-	This is used to get the current version of the driver and the firmware.
-
-scantype
-	This command is used to set the scan type to be used by the driver in
-	the scan command. This setting will not be used while performing a scan
-	for a specific SSID, as it is always done with scan type being active.
-
-	where the sub-commands are: -
-			active 	-- to set the scan type to active
-			passive -- to set the scan type to passive
-			get 	-- to get the scan type set in the driver
-
-getSNR
-	This command gets the average and non average value of Signal to Noise
-	Ratio of Beacon and Data.
-
-	where value is:-
-			0 	-- Beacon non-average.
-			1 	-- Beacon average.
-			2 	-- Data non-average.
-			3 	-- Data average.
-
-	If no value is given, all four values are returned in the order mentioned
-	above.
-
-	Note: This command is available only when STA is connected.
-
-getRSSI
-	This command gets the average and non average value os Receive Signal
-	Strength of Beacon and Data.
-
-	where value is:-
-			0 	-- Beacon non-average.
-			1 	-- Beacon average.
-			2 	-- Data non-average.
-			3 	-- Data average.
-
-	Note: This command is available only when STA is connected.
-
-getNF
-	This command gets the average and non average value of Noise Floor of
-	Beacon and Data.
-
-	where value is:-
-			0 	-- Beacon non-average.
-			1 	-- Beacon average.
-			2 	-- Data non-average.
-			3 	-- Data average.
-
-	Note: This command is available only when STA is connected.
-
-setrxant
-	This command is used to set the mode for Rx antenna.
-
-	The options that can be sent are:-
-			1 	-- Antenna 1.
-			2 	-- Antenna 2.
-			0xFFFF 	-- Diversity.
-
-	Usage:
-		iwpriv ethX setrxant 0x01: select Antenna 1.
-
-getrxant
-	This command is used to get the mode for Rx antenna.
-
-
-settxant
-	This command is used to set the mode for Tx antenna.
-		The options that can be sent are:-
-			1 	-- Antenna 1.
-			2 	-- Antenna 2.
-			0xFFFF 	-- Diversity.
-	Usage:
-		iwpriv ethX settxant 0x01: select Antenna 1.
-
-gettxant
-	This command is used to get the mode for Tx antenna.
-
-authalgs
-	This command is used by the WPA supplicant to set the authentication
-	algorithms in the station.
-
-8021xauthalgs
-	This command is used by the WPA supplicant to set the 8021.x authentication algorithm type
-	station.
-
-	where values can be:-
-			1 	-- None
-			2 	-- LEAP
-			4 	-- TLS
-			8 	-- TTLs
-			16	-- MD5
-
-
-encryptionmode
-	This command is used by the WPA supplicant to set the encryption algorithm.
-
-	where values can be:-
-			0 	-- NONE
-			1 	-- WEP40
-			2 	-- TKIP
-			3 	-- CCMP
-			4 	-- WEP104
-
-pre-TBTT
-	This command is used to set pre-TBTT time period where value is in microseconds.
-
 setregioncode
 	This command is used to set the region code in the station.
 	where value is 'region code' for various regions like
@@ -270,114 +109,6 @@ getregioncode
 	This command is used to get the region code information set in the
 	station.
 
-setbcnavg
-	Set the weighting factor for calculating RSSI.
-
-getbcnavg
-	Get weighting factor for calculating RSSI.
-
-setdataavg
-	Set the weighting factor for calculating SNR.
-
-setlisteninter
-	This command is used to set the listen interval in the
-	station.
-
-	where the value ranges between 1 - 255
-
-getlisteninter
-	This command is used to get the listen interval value set in the
-	station.
-
-setmultipledtim
-	This command is used to set the multiple dtim value in the
-	station.
-		where the value is 1,2,3,4,5,0xfffe
-		0xfffe means the firmware will use listen interval in association
-		command for waking up
-
-getmultipledtim
-	This command is used to get the multiple dtim value set in the station.
-
-atimwindow
-	This command is used to set the atim value in the
-	station.
-
-	where the value ranges between 0 - 50
-
-deauth
-	This command is used to send the de-authentication to the AP with which
-	the station is associated. This command is valid only when
-	station is in Infrastructure mode.
-
-	Note: This command is available only when STA is connected.
-
-adhocstop
-	This command is used to stop beacon transmission from the station and
-	go into idle state in ad-hoc mode.
-
-	Note: This command is available only when STA is connected.
-
-radioon
-	This command is used to turn on the RF antenna.
-
-radiooff
-	This command is sued to turn off the RF antenna.
-
-scanmode
-	This command is used to set the station to scan for either IBSS
-	networks or BSS networks or both BSS and IBSS networks. This
-	command can be used with sub commands,
-
-	where the value for
-			bss 	-- Scan All the BSS networks.
-			ibss 	-- Scan All the IBSS networks.
-			any 	-- Scan both BSS and IBSS networks.
-
-
-
-setwpaie
-	This command is used by WPA supplicant to send the WPA-IE to the driver.
-
-wlanidle-off
-	This command is used to get into idle state.
-
-	Note: This command is available only when STA is connected.
-
-wlanidle-on
-	This command is used to get off the idle state.
-
-	Note: This command is available only when STA is connected.
-
-
-getlog
-	This command is used to get the 802.11 statistics available in the
-		station.
-
-	Note: This command is available only when STA is connected.
-
-getadhocstatus
-	This command is used to get the ad-hoc Network Status.
-
-	The various status codes are:
-		AdhocStarted
-		AdhocJoined
-		AdhocIdle
-		InfraMode
-		AutoUnknownMode
-
-	Note: This command is available only when STA is connected.
-
-adhocgrate
-	This command is used to enable(1) g_rate, Disable(0) g_rate
-	and request(2) the status which g_rate is disabled/enabled,
-	for Ad-hoc creator.
-
-	where value is:-
-		0	-- Disabled
-		1	-- Enabled
-		2	-- Get
-
 ledgpio
 	This command is used to set/get LEDs.
 
@@ -400,253 +131,6 @@ ledgpio
 	Note: LED0 is invalid
 	Note: Maximum Number of LEDs are 16.
 
-inactivityto
-	This command is used by the host to set/get the inactivity timeout value,
-	which specifies when WLAN device is put to sleep.
-
-	Usage:
-		iwpriv ethX inactivityto [<timeout>]
-
-	where the parameter are:
-		timeout: timeout value in milliseconds.
-
-	Example:
-		iwpriv eth1 inactivityto
-			"get the timeout value"
-
-		iwpriv eth1 inactivityto X
-			"set timeout value to X ms"
-
-
-sleeppd
-	This command is used to configure the sleep period of the WLAN device.
-
-	Usage:
-		iwpriv ethX sleeppd [<sleep period>]
-
-	where the parameter are:
-		Period: sleep period in milliseconds. Range 10~60.
-
-	Example:
-		iwpriv eth1 sleeppd 10
-			"set period as 10 ms"
-		iwpriv eth1 sleeppd
-			"get the sleep period configuration"
-
-enable11d
-	This command is used to control 11d
-	where value is:-
-		1	-- Enabled
-		0	-- Disabled
-		2	-- Get
-
-
-
-
-tpccfg
-	Enables or disables automatic transmit power control.
-
-	The first parameter turns this feature on (1) or off (0).  When turning
-	on, the user must also supply four more parameters in the following
-	order:
-		-UseSNR (Use SNR (in addition to PER) for TPC algorithm),
-		-P0 (P0 power level for TPC),
-		-P1 (P1 power level for TPC),
-		-P2 (P2 power level for TPC).
-
-	Usage:
-		iwpriv ethX tpccfg: Get current configuration
-		iwpriv ethX tpccfg 0: disable auto TPC
-		iwpriv ethX tpccfg 0x01 0x00 0x05 0x0a 0x0d: enable auto TPC; do not use SNR;
-							     P0=0x05; P1=0x0a; P2=0x0d;
-		iwpriv ethX tpccfg 0x01 0x01 0x05 0x0a 0x0d: enable auto TPC; use SNR;
-							     P0=0x05; P1=0x0a; P2=0x0d.
-
-powercfg
-	Enables or disables power adaptation.
-
-	The first parameter turns this feature on (1) or off (0).  When turning
-	on, the user must also supply three more parameters in the following
-	order:
-		-P0 (P0 power level for Power Adaptation),
-		-P1 (P1 power level for Power Adaptation),
-		-P2 (P2 power level for Power Adaptation).
-
-	Usage:
-		iwpriv ethX powercfg: Get current configuration
-		iwpriv ethX powercfg 0: disable power adaptation
-		iwpriv ethX powercfg 1 0x0d 0x0f 0x12: enable power adaptation;
-						       P0=0x0d; P1=0x0f; P2=0x12.
-
-getafc
-	This command returns automatic frequency control parameters.  It returns
-	three integers:
-		-P0: automatic is on (1), or off (0),
-		-P1: current timing offset in PPM (part per million), and
-		-P2: current frequency offset in PPM.
-
-setafc
-	Set automatic frequency control options.
-
-	The first parameter turns automatic on (1) or off (0).
-	The user must supply two more parameters in either case, in the following
-  order:
-
-  When auto is on:
-
-		-P0 (automatic adjustment frequency threshold in PPM),
-		-P1 (automatic adjustment period in beacon period),
-
-  When auto is off:
-
-		-P0 (manual adjustment timing offset in PPM), and
-		-P1 (manual adjustment frequency offset in PPM).
-
-	Usage:
-		iwpriv ethX setafc 0 10 10: manual adjustment, both timing and frequcncy
-    offset are 10 PPM.
-
-		iwpriv ethX setafc 1 10 10 enable afc, automatic adjustment,
-    frequency threshold 10 PPM, for every 10 beacon periods.
-
-
-
-scanprobes
-	This command sets number of probe requests per channel.
-
-	Usage:
-		iwpriv ethX scanprobes 3 (set scan probes to 3)
-		iwpriv ethX scanprobes   (get scan probes)
-
-lolisteninter
-	This command sets the value of listen interval.
-
-	Usage:
-	iwpriv ethX lolisteninter 234 (set the lolisteninter to 234)
-	iwpriv ethX lolisteninter     (get the lolisteninter value)
-
-rateadapt
-	This command sets the data rates bitmap.
-	Where <n>
-		0: Disable auto rate adapt
-		1: Enable auto rate adapt
-
-	      <m>
-		 data rate bitmap
-			Bit	Data rate
-			0	1 Mbps
-			1	2 Mbps
-			2	5.5 Mbps
-			3	11 Mbps
-			4	Reserved
-			5	6 Mbps
-			6	9 Mbps
-			7	12 Mbps
-			8	18 Mbps
-			9	24 Mbps
-			10	36 Mbps
-			11	48 Mbps
-			12	54 Mbps
-			12-15	Reserved
-
-	Usage:
-	iwpriv ethX rateadapt
-			read the currect data rate setting
-	iwpriv ethX rateadapt 1 0x07
-			enable auto data rate adapt and
-			data rates are 1Mbps, 2Mbsp and 5.5Mbps
-
-
-txcontrol
-	This command is used to set the Tx rate, ack policy, and retry limit on a per packet basis.
-
-	Where value <n> is:
-	    if bit[4] == 1:
-		bit[3:0]        -- 0   1   2   3   4   5   6   7   8   9   10   11   12   13-16
-		Data Rate(Mbps) -- 1   2   5.5 11  Rsv 6   9   12  18  24  36   48   54   Rsv
-
-	    bit[12:8]
-		if bit[12] == 1, bit[11:8] specifies the Tx retry limit.
-
-	    bit[14:13] specifies per packet ack policy:
-		bit[14:13]
-		     1  0	use immediate ack policy for this packet
-		     1  1       use no ack policy for this packet
-		     0  x	use the per-packet ack policy setting
-
-	Usage:
-	iwpriv ethX txcontrol 0x7513
-			Use no-ack policy, 5 retires for Tx, 11Mbps rate
-
-
-
-psnullinterval
-	This command is used to set/request NULL package interval for Power Save
-	under infrastructure mode.
-
-	where value is:-
-		-1	-- Disabled
-		n>0	-- Set interval as n (seconds)
-
-prescan
-	This command is used to enable (1)/disable(0) auto prescan before assoicate to the ap
-
-	where value is:-
-		0	-- Disabled
-		1	-- Enabled
-		2       -- Get
-
-getrxinfo
-	This command gets non average value of Signal to Noise Ratio of Data and rate index.
-
-	The following table shows RateIndex and Rate
-
-		     RateIndex	Data rate
-			0	1 Mbps
-			1	2 Mbps
-			2	5.5 Mbps
-			3	11 Mbps
-			4	Reserved
-			5	6 Mbps
-			6	9 Mbps
-			7	12 Mbps
-			8	18 Mbps
-			9	24 Mbps
-			10	36 Mbps
-			11	48 Mbps
-			12	54 Mbps
-			13-15	Reserved
-
-gettxrate
-	This command gets current Tx rate index of the first packet associated with Rate Adaptation.
-
-	The following table shows RateIndex and Rate
-
-		     RateIndex	Data rate
-			0	1 Mbps
-			1	2 Mbps
-			2	5.5 Mbps
-			3	11 Mbps
-			4	Reserved
-			5	6 Mbps
-			6	9 Mbps
-			7	12 Mbps
-			8	18 Mbps
-			9	24 Mbps
-			10	36 Mbps
-			11	48 Mbps
-			12	54 Mbps
-			13-15	Reserved
-
-bcninterval
-	This command is used to sets beacon interval in adhoc mode when an argument is given, and gets current adhoc
-	beacon interval when no argument is given. The valid beacon interval is between 20 - 1000,
-	default beacon interval is 100.
-
-	Usage:
-		iwpriv ethX bcninterval 100  (set adhoc beacon interval to 100)
-		iwpriv ethX bcninterval      (get adhoc beacon interval)
-
 fwt_add
 	This command is used to insert an entry into the FWT table. The list of
 	parameters must follow the following structure: