Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 272 insertions, 0 deletions

diff --git a/drivers/serial/sunzilog.h b/drivers/serial/sunzilog.h
new file mode 100644
index 000000000000..7939b6d71270
--- /dev/null
+++ b/drivers/serial/sunzilog.h
@@ -0,0 +1,272 @@
+#ifndef _SUNZILOG_H
+#define _SUNZILOG_H
+
+struct zilog_channel {
+	volatile unsigned char control;
+	volatile unsigned char __pad1;
+	volatile unsigned char data;
+	volatile unsigned char __pad2;
+};
+
+struct zilog_layout {
+	struct zilog_channel channelB;
+	struct zilog_channel channelA;
+};
+
+#define NUM_ZSREGS    16
+
+/* Conversion routines to/from brg time constants from/to bits
+ * per second.
+ */
+#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
+#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
+
+/* The Zilog register set */
+
+#define	FLAG	0x7e
+
+/* Write Register 0 */
+#define	R0	0		/* Register selects */
+#define	R1	1
+#define	R2	2
+#define	R3	3
+#define	R4	4
+#define	R5	5
+#define	R6	6
+#define	R7	7
+#define	R8	8
+#define	R9	9
+#define	R10	10
+#define	R11	11
+#define	R12	12
+#define	R13	13
+#define	R14	14
+#define	R15	15
+
+#define	NULLCODE	0	/* Null Code */
+#define	POINT_HIGH	0x8	/* Select upper half of registers */
+#define	RES_EXT_INT	0x10	/* Reset Ext. Status Interrupts */
+#define	SEND_ABORT	0x18	/* HDLC Abort */
+#define	RES_RxINT_FC	0x20	/* Reset RxINT on First Character */
+#define	RES_Tx_P	0x28	/* Reset TxINT Pending */
+#define	ERR_RES		0x30	/* Error Reset */
+#define	RES_H_IUS	0x38	/* Reset highest IUS */
+
+#define	RES_Rx_CRC	0x40	/* Reset Rx CRC Checker */
+#define	RES_Tx_CRC	0x80	/* Reset Tx CRC Checker */
+#define	RES_EOM_L	0xC0	/* Reset EOM latch */
+
+/* Write Register 1 */
+
+#define	EXT_INT_ENAB	0x1	/* Ext Int Enable */
+#define	TxINT_ENAB	0x2	/* Tx Int Enable */
+#define	PAR_SPEC	0x4	/* Parity is special condition */
+
+#define	RxINT_DISAB	0	/* Rx Int Disable */
+#define	RxINT_FCERR	0x8	/* Rx Int on First Character Only or Error */
+#define	INT_ALL_Rx	0x10	/* Int on all Rx Characters or error */
+#define	INT_ERR_Rx	0x18	/* Int on error only */
+#define RxINT_MASK	0x18
+
+#define	WT_RDY_RT	0x20	/* Wait/Ready on R/T */
+#define	WT_FN_RDYFN	0x40	/* Wait/FN/Ready FN */
+#define	WT_RDY_ENAB	0x80	/* Wait/Ready Enable */
+
+/* Write Register #2 (Interrupt Vector) */
+
+/* Write Register 3 */
+
+#define	RxENAB  	0x1	/* Rx Enable */
+#define	SYNC_L_INH	0x2	/* Sync Character Load Inhibit */
+#define	ADD_SM		0x4	/* Address Search Mode (SDLC) */
+#define	RxCRC_ENAB	0x8	/* Rx CRC Enable */
+#define	ENT_HM		0x10	/* Enter Hunt Mode */
+#define	AUTO_ENAB	0x20	/* Auto Enables */
+#define	Rx5		0x0	/* Rx 5 Bits/Character */
+#define	Rx7		0x40	/* Rx 7 Bits/Character */
+#define	Rx6		0x80	/* Rx 6 Bits/Character */
+#define	Rx8		0xc0	/* Rx 8 Bits/Character */
+#define RxN_MASK	0xc0
+
+/* Write Register 4 */
+
+#define	PAR_ENAB	0x1	/* Parity Enable */
+#define	PAR_EVEN	0x2	/* Parity Even/Odd* */
+
+#define	SYNC_ENAB	0	/* Sync Modes Enable */
+#define	SB1		0x4	/* 1 stop bit/char */
+#define	SB15		0x8	/* 1.5 stop bits/char */
+#define	SB2		0xc	/* 2 stop bits/char */
+
+#define	MONSYNC		0	/* 8 Bit Sync character */
+#define	BISYNC		0x10	/* 16 bit sync character */
+#define	SDLC		0x20	/* SDLC Mode (01111110 Sync Flag) */
+#define	EXTSYNC		0x30	/* External Sync Mode */
+
+#define	X1CLK		0x0	/* x1 clock mode */
+#define	X16CLK		0x40	/* x16 clock mode */
+#define	X32CLK		0x80	/* x32 clock mode */
+#define	X64CLK		0xC0	/* x64 clock mode */
+#define XCLK_MASK	0xC0
+
+/* Write Register 5 */
+
+#define	TxCRC_ENAB	0x1	/* Tx CRC Enable */
+#define	RTS		0x2	/* RTS */
+#define	SDLC_CRC	0x4	/* SDLC/CRC-16 */
+#define	TxENAB		0x8	/* Tx Enable */
+#define	SND_BRK		0x10	/* Send Break */
+#define	Tx5		0x0	/* Tx 5 bits (or less)/character */
+#define	Tx7		0x20	/* Tx 7 bits/character */
+#define	Tx6		0x40	/* Tx 6 bits/character */
+#define	Tx8		0x60	/* Tx 8 bits/character */
+#define TxN_MASK	0x60
+#define	DTR		0x80	/* DTR */
+
+/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
+
+/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
+
+/* Write Register 8 (transmit buffer) */
+
+/* Write Register 9 (Master interrupt control) */
+#define	VIS	1	/* Vector Includes Status */
+#define	NV	2	/* No Vector */
+#define	DLC	4	/* Disable Lower Chain */
+#define	MIE	8	/* Master Interrupt Enable */
+#define	STATHI	0x10	/* Status high */
+#define	NORESET	0	/* No reset on write to R9 */
+#define	CHRB	0x40	/* Reset channel B */
+#define	CHRA	0x80	/* Reset channel A */
+#define	FHWRES	0xc0	/* Force hardware reset */
+
+/* Write Register 10 (misc control bits) */
+#define	BIT6	1	/* 6 bit/8bit sync */
+#define	LOOPMODE 2	/* SDLC Loop mode */
+#define	ABUNDER	4	/* Abort/flag on SDLC xmit underrun */
+#define	MARKIDLE 8	/* Mark/flag on idle */
+#define	GAOP	0x10	/* Go active on poll */
+#define	NRZ	0	/* NRZ mode */
+#define	NRZI	0x20	/* NRZI mode */
+#define	FM1	0x40	/* FM1 (transition = 1) */
+#define	FM0	0x60	/* FM0 (transition = 0) */
+#define	CRCPS	0x80	/* CRC Preset I/O */
+
+/* Write Register 11 (Clock Mode control) */
+#define	TRxCXT	0	/* TRxC = Xtal output */
+#define	TRxCTC	1	/* TRxC = Transmit clock */
+#define	TRxCBR	2	/* TRxC = BR Generator Output */
+#define	TRxCDP	3	/* TRxC = DPLL output */
+#define	TRxCOI	4	/* TRxC O/I */
+#define	TCRTxCP	0	/* Transmit clock = RTxC pin */
+#define	TCTRxCP	8	/* Transmit clock = TRxC pin */
+#define	TCBR	0x10	/* Transmit clock = BR Generator output */
+#define	TCDPLL	0x18	/* Transmit clock = DPLL output */
+#define	RCRTxCP	0	/* Receive clock = RTxC pin */
+#define	RCTRxCP	0x20	/* Receive clock = TRxC pin */
+#define	RCBR	0x40	/* Receive clock = BR Generator output */
+#define	RCDPLL	0x60	/* Receive clock = DPLL output */
+#define	RTxCX	0x80	/* RTxC Xtal/No Xtal */
+
+/* Write Register 12 (lower byte of baud rate generator time constant) */
+
+/* Write Register 13 (upper byte of baud rate generator time constant) */
+
+/* Write Register 14 (Misc control bits) */
+#define	BRENAB 	1	/* Baud rate generator enable */
+#define	BRSRC	2	/* Baud rate generator source */
+#define	DTRREQ	4	/* DTR/Request function */
+#define	AUTOECHO 8	/* Auto Echo */
+#define	LOOPBAK	0x10	/* Local loopback */
+#define	SEARCH	0x20	/* Enter search mode */
+#define	RMC	0x40	/* Reset missing clock */
+#define	DISDPLL	0x60	/* Disable DPLL */
+#define	SSBR	0x80	/* Set DPLL source = BR generator */
+#define	SSRTxC	0xa0	/* Set DPLL source = RTxC */
+#define	SFMM	0xc0	/* Set FM mode */
+#define	SNRZI	0xe0	/* Set NRZI mode */
+
+/* Write Register 15 (external/status interrupt control) */
+#define	ZCIE	2	/* Zero count IE */
+#define	DCDIE	8	/* DCD IE */
+#define	SYNCIE	0x10	/* Sync/hunt IE */
+#define	CTSIE	0x20	/* CTS IE */
+#define	TxUIE	0x40	/* Tx Underrun/EOM IE */
+#define	BRKIE	0x80	/* Break/Abort IE */
+
+
+/* Read Register 0 */
+#define	Rx_CH_AV	0x1	/* Rx Character Available */
+#define	ZCOUNT		0x2	/* Zero count */
+#define	Tx_BUF_EMP	0x4	/* Tx Buffer empty */
+#define	DCD		0x8	/* DCD */
+#define	SYNC		0x10	/* Sync/hunt */
+#define	CTS		0x20	/* CTS */
+#define	TxEOM		0x40	/* Tx underrun */
+#define	BRK_ABRT	0x80	/* Break/Abort */
+
+/* Read Register 1 */
+#define	ALL_SNT		0x1	/* All sent */
+/* Residue Data for 8 Rx bits/char programmed */
+#define	RES3		0x8	/* 0/3 */
+#define	RES4		0x4	/* 0/4 */
+#define	RES5		0xc	/* 0/5 */
+#define	RES6		0x2	/* 0/6 */
+#define	RES7		0xa	/* 0/7 */
+#define	RES8		0x6	/* 0/8 */
+#define	RES18		0xe	/* 1/8 */
+#define	RES28		0x0	/* 2/8 */
+/* Special Rx Condition Interrupts */
+#define	PAR_ERR		0x10	/* Parity error */
+#define	Rx_OVR		0x20	/* Rx Overrun Error */
+#define	CRC_ERR		0x40	/* CRC/Framing Error */
+#define	END_FR		0x80	/* End of Frame (SDLC) */
+
+/* Read Register 2 (channel b only) - Interrupt vector */
+#define CHB_Tx_EMPTY	0x00
+#define CHB_EXT_STAT	0x02
+#define CHB_Rx_AVAIL	0x04
+#define CHB_SPECIAL	0x06
+#define CHA_Tx_EMPTY	0x08
+#define CHA_EXT_STAT	0x0a
+#define CHA_Rx_AVAIL	0x0c
+#define CHA_SPECIAL	0x0e
+#define STATUS_MASK	0x0e
+
+/* Read Register 3 (interrupt pending register) ch a only */
+#define	CHBEXT	0x1		/* Channel B Ext/Stat IP */
+#define	CHBTxIP	0x2		/* Channel B Tx IP */
+#define	CHBRxIP	0x4		/* Channel B Rx IP */
+#define	CHAEXT	0x8		/* Channel A Ext/Stat IP */
+#define	CHATxIP	0x10		/* Channel A Tx IP */
+#define	CHARxIP	0x20		/* Channel A Rx IP */
+
+/* Read Register 8 (receive data register) */
+
+/* Read Register 10  (misc status bits) */
+#define	ONLOOP	2		/* On loop */
+#define	LOOPSEND 0x10		/* Loop sending */
+#define	CLK2MIS	0x40		/* Two clocks missing */
+#define	CLK1MIS	0x80		/* One clock missing */
+
+/* Read Register 12 (lower byte of baud rate generator constant) */
+
+/* Read Register 13 (upper byte of baud rate generator constant) */
+
+/* Read Register 15 (value of WR 15) */
+
+/* Misc macros */
+#define ZS_CLEARERR(channel)    do { sbus_writeb(ERR_RES, &channel->control); \
+				     udelay(5); } while(0)
+
+#define ZS_CLEARSTAT(channel)   do { sbus_writeb(RES_EXT_INT, &channel->control); \
+				     udelay(5); } while(0)
+
+#define ZS_CLEARFIFO(channel)   do { sbus_readb(&channel->data); \
+				     udelay(2); \
+				     sbus_readb(&channel->data); \
+				     udelay(2); \
+				     sbus_readb(&channel->data); \
+				     udelay(2); } while(0)
+
+#endif /* _SUNZILOG_H */