Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
  eHEA: Fix bonding support
  Blackfin ethernet driver: on chip ethernet MAC controller driver
  fix wrong argument of tc35815_read_plat_dev_addr()
  ARM/ETHER3: Handle multicast frames.
  SAA9730: Handle multicast frames.
  NI5010: Handle multicast frames.
  NS83820: Handle multicast frames.
  Fix RGMII-ID handling in gianfar
  Fix Vitesse RGMII-ID support
  Add phy-connection-type to gianfar nodes
  Fix Vitesse 824x PHY interrupt acking
  [PATCH] zd1211rw: Add ID for Siemens Gigaset USB Stick 54
  [PATCH] zd1211rw: Add ID for Planex GW-US54GXS
  [PATCH] Update version ipw2200 stamp to 1.2.2
  [PATCH] ipw2200: Fix ipw_isr() comments error on shared IRQ
  [PATCH] Fix ipw2200 set wrong power parameter causing firmware error
  [PATCH] ipw2100: Fix `iwpriv set_power` error
  [PATCH] softmac: Channel is listed twice in scan output

16 files changed, 1279 insertions, 51 deletions

diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 5fb659f8b20e..3073f679584b 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -838,6 +838,50 @@ config ULTRA32
 	  <file:Documentation/networking/net-modules.txt>. The module
 	  will be called smc-ultra32.
 
+config BFIN_MAC
+	tristate "Blackfin 536/537 on-chip mac support"
+	depends on NET_ETHERNET && (BF537 || BF536) && (!BF537_PORT_H)
+	select CRC32
+	select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
+	help
+	  This is the driver for blackfin on-chip mac device. Say Y if you want it
+	  compiled into the kernel. This driver is also available as a module
+	  ( = code which can be inserted in and removed from the running kernel
+	  whenever you want). The module will be called bfin_mac.
+
+config BFIN_MAC_USE_L1
+	bool "Use L1 memory for rx/tx packets"
+	depends on BFIN_MAC && BF537
+	default y
+	help
+	  To get maximum network performace, you should use L1 memory as rx/tx buffers.
+	  Say N here if you want to reserve L1 memory for other uses.
+
+config BFIN_TX_DESC_NUM
+	int "Number of transmit buffer packets"
+	depends on BFIN_MAC
+	range 6 10 if BFIN_MAC_USE_L1
+	range 10 100
+	default "10"
+	help
+	  Set the number of buffer packets used in driver.
+
+config BFIN_RX_DESC_NUM
+	int "Number of receive buffer packets"
+	depends on BFIN_MAC
+	range 20 100 if BFIN_MAC_USE_L1
+	range 20 800
+	default "20"
+	help
+	  Set the number of buffer packets used in driver.
+
+config BFIN_MAC_RMII
+	bool "RMII PHY Interface (EXPERIMENTAL)"
+	depends on BFIN_MAC && EXPERIMENTAL
+	default n
+	help
+	  Use Reduced PHY MII Interface
+
 config SMC9194
 	tristate "SMC 9194 support"
 	depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN)
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 0e286ab8855a..aaaa0a04bb46 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -200,6 +200,7 @@ obj-$(CONFIG_S2IO) += s2io.o
 obj-$(CONFIG_MYRI10GE) += myri10ge/
 obj-$(CONFIG_SMC91X) += smc91x.o
 obj-$(CONFIG_SMC911X) += smc911x.o
+obj-$(CONFIG_BFIN_MAC) += bfin_mac.o
 obj-$(CONFIG_DM9000) += dm9000.o
 obj-$(CONFIG_FEC_8XX) += fec_8xx/
 obj-$(CONFIG_PASEMI_MAC) += pasemi_mac.o
diff --git a/drivers/net/arm/ether3.c b/drivers/net/arm/ether3.c
index da713500654d..a7cac695a9bd 100644
--- a/drivers/net/arm/ether3.c
+++ b/drivers/net/arm/ether3.c
@@ -464,7 +464,7 @@ static void ether3_setmulticastlist(struct net_device *dev)
 	if (dev->flags & IFF_PROMISC) {
 		/* promiscuous mode */
 		priv(dev)->regs.config1 |= CFG1_RECVPROMISC;
-	} else if (dev->flags & IFF_ALLMULTI) {
+	} else if (dev->flags & IFF_ALLMULTI || dev->mc_count) {
 		priv(dev)->regs.config1 |= CFG1_RECVSPECBRMULTI;
 	} else
 		priv(dev)->regs.config1 |= CFG1_RECVSPECBROAD;
diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c
new file mode 100644
index 000000000000..9a08d656f1ce
--- /dev/null
+++ b/drivers/net/bfin_mac.c
@@ -0,0 +1,1009 @@
+/*
+ * File:	drivers/net/bfin_mac.c
+ * Based on:
+ * Maintainer:
+ * 		Bryan Wu <bryan.wu@analog.com>
+ *
+ * Original author:
+ * 		Luke Yang <luke.yang@analog.com>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ *		Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs:	Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software ;  you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation ;  either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY ;  without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program ;  see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/errno.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/crc32.h>
+#include <linux/device.h>
+#include <linux/spinlock.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+
+#include <linux/platform_device.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+
+#include <asm/dma.h>
+#include <linux/dma-mapping.h>
+
+#include <asm/blackfin.h>
+#include <asm/cacheflush.h>
+#include <asm/portmux.h>
+
+#include "bfin_mac.h"
+
+#define DRV_NAME	"bfin_mac"
+#define DRV_VERSION	"1.1"
+#define DRV_AUTHOR	"Bryan Wu, Luke Yang"
+#define DRV_DESC	"Blackfin BF53[67] on-chip Ethernet MAC driver"
+
+MODULE_AUTHOR(DRV_AUTHOR);
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION(DRV_DESC);
+
+#if defined(CONFIG_BFIN_MAC_USE_L1)
+# define bfin_mac_alloc(dma_handle, size)  l1_data_sram_zalloc(size)
+# define bfin_mac_free(dma_handle, ptr)    l1_data_sram_free(ptr)
+#else
+# define bfin_mac_alloc(dma_handle, size) \
+	dma_alloc_coherent(NULL, size, dma_handle, GFP_KERNEL)
+# define bfin_mac_free(dma_handle, ptr) \
+	dma_free_coherent(NULL, sizeof(*ptr), ptr, dma_handle)
+#endif
+
+#define PKT_BUF_SZ 1580
+
+#define MAX_TIMEOUT_CNT	500
+
+/* pointers to maintain transmit list */
+static struct net_dma_desc_tx *tx_list_head;
+static struct net_dma_desc_tx *tx_list_tail;
+static struct net_dma_desc_rx *rx_list_head;
+static struct net_dma_desc_rx *rx_list_tail;
+static struct net_dma_desc_rx *current_rx_ptr;
+static struct net_dma_desc_tx *current_tx_ptr;
+static struct net_dma_desc_tx *tx_desc;
+static struct net_dma_desc_rx *rx_desc;
+
+static void desc_list_free(void)
+{
+	struct net_dma_desc_rx *r;
+	struct net_dma_desc_tx *t;
+	int i;
+#if !defined(CONFIG_BFIN_MAC_USE_L1)
+	dma_addr_t dma_handle = 0;
+#endif
+
+	if (tx_desc) {
+		t = tx_list_head;
+		for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) {
+			if (t) {
+				if (t->skb) {
+					dev_kfree_skb(t->skb);
+					t->skb = NULL;
+				}
+				t = t->next;
+			}
+		}
+		bfin_mac_free(dma_handle, tx_desc);
+	}
+
+	if (rx_desc) {
+		r = rx_list_head;
+		for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) {
+			if (r) {
+				if (r->skb) {
+					dev_kfree_skb(r->skb);
+					r->skb = NULL;
+				}
+				r = r->next;
+			}
+		}
+		bfin_mac_free(dma_handle, rx_desc);
+	}
+}
+
+static int desc_list_init(void)
+{
+	int i;
+	struct sk_buff *new_skb;
+#if !defined(CONFIG_BFIN_MAC_USE_L1)
+	/*
+	 * This dma_handle is useless in Blackfin dma_alloc_coherent().
+	 * The real dma handler is the return value of dma_alloc_coherent().
+	 */
+	dma_addr_t dma_handle;
+#endif
+
+	tx_desc = bfin_mac_alloc(&dma_handle,
+				sizeof(struct net_dma_desc_tx) *
+				CONFIG_BFIN_TX_DESC_NUM);
+	if (tx_desc == NULL)
+		goto init_error;
+
+	rx_desc = bfin_mac_alloc(&dma_handle,
+				sizeof(struct net_dma_desc_rx) *
+				CONFIG_BFIN_RX_DESC_NUM);
+	if (rx_desc == NULL)
+		goto init_error;
+
+	/* init tx_list */
+	tx_list_head = tx_list_tail = tx_desc;
+
+	for (i = 0; i < CONFIG_BFIN_TX_DESC_NUM; i++) {
+		struct net_dma_desc_tx *t = tx_desc + i;
+		struct dma_descriptor *a = &(t->desc_a);
+		struct dma_descriptor *b = &(t->desc_b);
+
+		/*
+		 * disable DMA
+		 * read from memory WNR = 0
+		 * wordsize is 32 bits
+		 * 6 half words is desc size
+		 * large desc flow
+		 */
+		a->config = WDSIZE_32 | NDSIZE_6 | DMAFLOW_LARGE;
+		a->start_addr = (unsigned long)t->packet;
+		a->x_count = 0;
+		a->next_dma_desc = b;
+
+		/*
+		 * enabled DMA
+		 * write to memory WNR = 1
+		 * wordsize is 32 bits
+		 * disable interrupt
+		 * 6 half words is desc size
+		 * large desc flow
+		 */
+		b->config = DMAEN | WNR | WDSIZE_32 | NDSIZE_6 | DMAFLOW_LARGE;
+		b->start_addr = (unsigned long)(&(t->status));
+		b->x_count = 0;
+
+		t->skb = NULL;
+		tx_list_tail->desc_b.next_dma_desc = a;
+		tx_list_tail->next = t;
+		tx_list_tail = t;
+	}
+	tx_list_tail->next = tx_list_head;	/* tx_list is a circle */
+	tx_list_tail->desc_b.next_dma_desc = &(tx_list_head->desc_a);
+	current_tx_ptr = tx_list_head;
+
+	/* init rx_list */
+	rx_list_head = rx_list_tail = rx_desc;
+
+	for (i = 0; i < CONFIG_BFIN_RX_DESC_NUM; i++) {
+		struct net_dma_desc_rx *r = rx_desc + i;
+		struct dma_descriptor *a = &(r->desc_a);
+		struct dma_descriptor *b = &(r->desc_b);
+
+		/* allocate a new skb for next time receive */
+		new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
+		if (!new_skb) {
+			printk(KERN_NOTICE DRV_NAME
+			       ": init: low on mem - packet dropped\n");
+			goto init_error;
+		}
+		skb_reserve(new_skb, 2);
+		r->skb = new_skb;
+
+		/*
+		 * enabled DMA
+		 * write to memory WNR = 1
+		 * wordsize is 32 bits
+		 * disable interrupt
+		 * 6 half words is desc size
+		 * large desc flow
+		 */
+		a->config = DMAEN | WNR | WDSIZE_32 | NDSIZE_6 | DMAFLOW_LARGE;
+		/* since RXDWA is enabled */
+		a->start_addr = (unsigned long)new_skb->data - 2;
+		a->x_count = 0;
+		a->next_dma_desc = b;
+
+		/*
+		 * enabled DMA
+		 * write to memory WNR = 1
+		 * wordsize is 32 bits
+		 * enable interrupt
+		 * 6 half words is desc size
+		 * large desc flow
+		 */
+		b->config = DMAEN | WNR | WDSIZE_32 | DI_EN |
+				NDSIZE_6 | DMAFLOW_LARGE;
+		b->start_addr = (unsigned long)(&(r->status));
+		b->x_count = 0;
+
+		rx_list_tail->desc_b.next_dma_desc = a;
+		rx_list_tail->next = r;
+		rx_list_tail = r;
+	}
+	rx_list_tail->next = rx_list_head;	/* rx_list is a circle */
+	rx_list_tail->desc_b.next_dma_desc = &(rx_list_head->desc_a);
+	current_rx_ptr = rx_list_head;
+
+	return 0;
+
+init_error:
+	desc_list_free();
+	printk(KERN_ERR DRV_NAME ": kmalloc failed\n");
+	return -ENOMEM;
+}
+
+
+/*---PHY CONTROL AND CONFIGURATION-----------------------------------------*/
+
+/* Set FER regs to MUX in Ethernet pins */
+static int setup_pin_mux(int action)
+{
+#if defined(CONFIG_BFIN_MAC_RMII)
+	u16 pin_req[] = P_RMII0;
+#else
+	u16 pin_req[] = P_MII0;
+#endif
+
+	if (action) {
+		if (peripheral_request_list(pin_req, DRV_NAME)) {
+			printk(KERN_ERR DRV_NAME
+			": Requesting Peripherals failed\n");
+			return -EFAULT;
+		}
+	} else
+		peripheral_free_list(pin_req);
+
+	return 0;
+}
+
+/* Wait until the previous MDC/MDIO transaction has completed */
+static void poll_mdc_done(void)
+{
+	int timeout_cnt = MAX_TIMEOUT_CNT;
+
+	/* poll the STABUSY bit */
+	while ((bfin_read_EMAC_STAADD()) & STABUSY) {
+		mdelay(10);
+		if (timeout_cnt-- < 0) {
+			printk(KERN_ERR DRV_NAME
+			": wait MDC/MDIO transaction to complete timeout\n");
+			break;
+		}
+	}
+}
+
+/* Read an off-chip register in a PHY through the MDC/MDIO port */
+static u16 read_phy_reg(u16 PHYAddr, u16 RegAddr)
+{
+	poll_mdc_done();
+	/* read mode */
+	bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) |
+				SET_REGAD(RegAddr) |
+				STABUSY);
+	poll_mdc_done();
+
+	return (u16) bfin_read_EMAC_STADAT();
+}
+
+/* Write an off-chip register in a PHY through the MDC/MDIO port */
+static void raw_write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
+{
+	bfin_write_EMAC_STADAT(Data);
+
+	/* write mode */
+	bfin_write_EMAC_STAADD(SET_PHYAD(PHYAddr) |
+				SET_REGAD(RegAddr) |
+				STAOP |
+				STABUSY);
+
+	poll_mdc_done();
+}
+
+static void write_phy_reg(u16 PHYAddr, u16 RegAddr, u32 Data)
+{
+	poll_mdc_done();
+	raw_write_phy_reg(PHYAddr, RegAddr, Data);
+}
+
+/* set up the phy */
+static void bf537mac_setphy(struct net_device *dev)
+{
+	u16 phydat;
+	struct bf537mac_local *lp = netdev_priv(dev);
+
+	/* Program PHY registers */
+	pr_debug("start setting up phy\n");
+
+	/* issue a reset */
+	raw_write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, 0x8000);
+
+	/* wait half a second */
+	msleep(500);
+
+	phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
+
+	/* advertise flow control supported */
+	phydat = read_phy_reg(lp->PhyAddr, PHYREG_ANAR);
+	phydat |= (1 << 10);
+	write_phy_reg(lp->PhyAddr, PHYREG_ANAR, phydat);
+
+	phydat = 0;
+	if (lp->Negotiate)
+		phydat |= 0x1000;	/* enable auto negotiation */
+	else {
+		if (lp->FullDuplex)
+			phydat |= (1 << 8);	/* full duplex */
+		else
+			phydat &= (~(1 << 8));	/* half duplex */
+
+		if (!lp->Port10)
+			phydat |= (1 << 13);	/* 100 Mbps */
+		else
+			phydat &= (~(1 << 13));	/* 10 Mbps */
+	}
+
+	if (lp->Loopback)
+		phydat |= (1 << 14);	/* enable TX->RX loopback */
+
+	write_phy_reg(lp->PhyAddr, PHYREG_MODECTL, phydat);
+	msleep(500);
+
+	phydat = read_phy_reg(lp->PhyAddr, PHYREG_MODECTL);
+	/* check for SMSC PHY */
+	if ((read_phy_reg(lp->PhyAddr, PHYREG_PHYID1) == 0x7) &&
+	((read_phy_reg(lp->PhyAddr, PHYREG_PHYID2) & 0xfff0) == 0xC0A0)) {
+		/*
+		 * we have SMSC PHY so reqest interrupt
+		 * on link down condition
+		 */
+
+		/* enable interrupts */
+		write_phy_reg(lp->PhyAddr, 30, 0x0ff);
+	}
+}
+
+/**************************************************************************/
+void setup_system_regs(struct net_device *dev)
+{
+	int phyaddr;
+	unsigned short sysctl, phydat;
+	u32 opmode;
+	struct bf537mac_local *lp = netdev_priv(dev);
+	int count = 0;
+
+	phyaddr = lp->PhyAddr;
+
+	/* Enable PHY output */
+	if (!(bfin_read_VR_CTL() & PHYCLKOE))
+		bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
+
+	/* MDC  = 2.5 MHz */
+	sysctl = SET_MDCDIV(24);
+	/* Odd word alignment for Receive Frame DMA word */
+	/* Configure checksum support and rcve frame word alignment */
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+	sysctl |= RXDWA | RXCKS;
+#else
+	sysctl |= RXDWA;
+#endif
+	bfin_write_EMAC_SYSCTL(sysctl);
+	/* auto negotiation on  */
+	/* full duplex          */
+	/* 100 Mbps             */
+	phydat = PHY_ANEG_EN | PHY_DUPLEX | PHY_SPD_SET;
+	write_phy_reg(phyaddr, PHYREG_MODECTL, phydat);
+
+	/* test if full duplex supported */
+	do {
+		msleep(100);
+		phydat = read_phy_reg(phyaddr, PHYREG_MODESTAT);
+		if (count > 30) {
+			printk(KERN_NOTICE DRV_NAME ": Link is down\n");
+			printk(KERN_NOTICE DRV_NAME
+				 "please check your network connection\n");
+			break;
+		}
+		count++;
+	} while (!(phydat & 0x0004));
+
+	phydat = read_phy_reg(phyaddr, PHYREG_ANLPAR);
+
+	if ((phydat & 0x0100) || (phydat & 0x0040)) {
+		opmode = FDMODE;
+	} else {
+		opmode = 0;
+		printk(KERN_INFO DRV_NAME
+			": Network is set to half duplex\n");
+	}
+
+#if defined(CONFIG_BFIN_MAC_RMII)
+	opmode |= RMII; /* For Now only 100MBit are supported */
+#endif
+
+	bfin_write_EMAC_OPMODE(opmode);
+
+	bfin_write_EMAC_MMC_CTL(RSTC | CROLL);
+
+	/* Initialize the TX DMA channel registers */
+	bfin_write_DMA2_X_COUNT(0);
+	bfin_write_DMA2_X_MODIFY(4);
+	bfin_write_DMA2_Y_COUNT(0);
+	bfin_write_DMA2_Y_MODIFY(0);
+
+	/* Initialize the RX DMA channel registers */
+	bfin_write_DMA1_X_COUNT(0);
+	bfin_write_DMA1_X_MODIFY(4);
+	bfin_write_DMA1_Y_COUNT(0);
+	bfin_write_DMA1_Y_MODIFY(0);
+}
+
+void setup_mac_addr(u8 * mac_addr)
+{
+	u32 addr_low = le32_to_cpu(*(__le32 *) & mac_addr[0]);
+	u16 addr_hi = le16_to_cpu(*(__le16 *) & mac_addr[4]);
+
+	/* this depends on a little-endian machine */
+	bfin_write_EMAC_ADDRLO(addr_low);
+	bfin_write_EMAC_ADDRHI(addr_hi);
+}
+
+static void adjust_tx_list(void)
+{
+	int timeout_cnt = MAX_TIMEOUT_CNT;
+
+	if (tx_list_head->status.status_word != 0
+	    && current_tx_ptr != tx_list_head) {
+		goto adjust_head;	/* released something, just return; */
+	}
+
+	/*
+	 * if nothing released, check wait condition
+	 * current's next can not be the head,
+	 * otherwise the dma will not stop as we want
+	 */
+	if (current_tx_ptr->next->next == tx_list_head) {
+		while (tx_list_head->status.status_word == 0) {
+			mdelay(10);
+			if (tx_list_head->status.status_word != 0
+			    || !(bfin_read_DMA2_IRQ_STATUS() & 0x08)) {
+				goto adjust_head;
+			}
+			if (timeout_cnt-- < 0) {
+				printk(KERN_ERR DRV_NAME
+				": wait for adjust tx list head timeout\n");
+				break;
+			}
+		}
+		if (tx_list_head->status.status_word != 0) {
+			goto adjust_head;
+		}
+	}
+
+	return;
+
+adjust_head:
+	do {
+		tx_list_head->desc_a.config &= ~DMAEN;
+		tx_list_head->status.status_word = 0;
+		if (tx_list_head->skb) {
+			dev_kfree_skb(tx_list_head->skb);
+			tx_list_head->skb = NULL;
+		} else {
+			printk(KERN_ERR DRV_NAME
+			       ": no sk_buff in a transmitted frame!\n");
+		}
+		tx_list_head = tx_list_head->next;
+	} while (tx_list_head->status.status_word != 0
+		 && current_tx_ptr != tx_list_head);
+	return;
+
+}
+
+static int bf537mac_hard_start_xmit(struct sk_buff *skb,
+				struct net_device *dev)
+{
+	struct bf537mac_local *lp = netdev_priv(dev);
+	unsigned int data;
+
+	current_tx_ptr->skb = skb;
+
+	/*
+	 * Is skb->data always 16-bit aligned?
+	 * Do we need to memcpy((char *)(tail->packet + 2), skb->data, len)?
+	 */
+	if ((((unsigned int)(skb->data)) & 0x02) == 2) {
+		/* move skb->data to current_tx_ptr payload */
+		data = (unsigned int)(skb->data) - 2;
+		*((unsigned short *)data) = (unsigned short)(skb->len);
+		current_tx_ptr->desc_a.start_addr = (unsigned long)data;
+		/* this is important! */
+		blackfin_dcache_flush_range(data, (data + (skb->len)) + 2);
+
+	} else {
+		*((unsigned short *)(current_tx_ptr->packet)) =
+		    (unsigned short)(skb->len);
+		memcpy((char *)(current_tx_ptr->packet + 2), skb->data,
+		       (skb->len));
+		current_tx_ptr->desc_a.start_addr =
+		    (unsigned long)current_tx_ptr->packet;
+		if (current_tx_ptr->status.status_word != 0)
+			current_tx_ptr->status.status_word = 0;
+		blackfin_dcache_flush_range((unsigned int)current_tx_ptr->
+					    packet,
+					    (unsigned int)(current_tx_ptr->
+							   packet + skb->len) +
+					    2);
+	}
+
+	/* enable this packet's dma */
+	current_tx_ptr->desc_a.config |= DMAEN;
+
+	/* tx dma is running, just return */
+	if (bfin_read_DMA2_IRQ_STATUS() & 0x08)
+		goto out;
+
+	/* tx dma is not running */
+	bfin_write_DMA2_NEXT_DESC_PTR(&(current_tx_ptr->desc_a));
+	/* dma enabled, read from memory, size is 6 */
+	bfin_write_DMA2_CONFIG(current_tx_ptr->desc_a.config);
+	/* Turn on the EMAC tx */
+	bfin_write_EMAC_OPMODE(bfin_read_EMAC_OPMODE() | TE);
+
+out:
+	adjust_tx_list();
+	current_tx_ptr = current_tx_ptr->next;
+	dev->trans_start = jiffies;
+	lp->stats.tx_packets++;
+	lp->stats.tx_bytes += (skb->len);
+	return 0;
+}
+
+static void bf537mac_rx(struct net_device *dev)
+{
+	struct sk_buff *skb, *new_skb;
+	struct bf537mac_local *lp = netdev_priv(dev);
+	unsigned short len;
+
+	/* allocate a new skb for next time receive */
+	skb = current_rx_ptr->skb;
+	new_skb = dev_alloc_skb(PKT_BUF_SZ + 2);
+	if (!new_skb) {
+		printk(KERN_NOTICE DRV_NAME
+		       ": rx: low on mem - packet dropped\n");
+		lp->stats.rx_dropped++;
+		goto out;
+	}
+	/* reserve 2 bytes for RXDWA padding */
+	skb_reserve(new_skb, 2);
+	current_rx_ptr->skb = new_skb;
+	current_rx_ptr->desc_a.start_addr = (unsigned long)new_skb->data - 2;
+
+	len = (unsigned short)((current_rx_ptr->status.status_word) & RX_FRLEN);
+	skb_put(skb, len);
+	blackfin_dcache_invalidate_range((unsigned long)skb->head,
+					 (unsigned long)skb->tail);
+
+	dev->last_rx = jiffies;
+	skb->dev = dev;
+	skb->protocol = eth_type_trans(skb, dev);
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+	skb->csum = current_rx_ptr->status.ip_payload_csum;
+	skb->ip_summed = CHECKSUM_PARTIAL;
+#endif
+
+	netif_rx(skb);
+	lp->stats.rx_packets++;
+	lp->stats.rx_bytes += len;
+	current_rx_ptr->status.status_word = 0x00000000;
+	current_rx_ptr = current_rx_ptr->next;
+
+out:
+	return;
+}
+
+/* interrupt routine to handle rx and error signal */
+static irqreturn_t bf537mac_interrupt(int irq, void *dev_id)
+{
+	struct net_device *dev = dev_id;
+	int number = 0;
+
+get_one_packet:
+	if (current_rx_ptr->status.status_word == 0) {
+		/* no more new packet received */
+		if (number == 0) {
+			if (current_rx_ptr->next->status.status_word != 0) {
+				current_rx_ptr = current_rx_ptr->next;
+				goto real_rx;
+			}
+		}
+		bfin_write_DMA1_IRQ_STATUS(bfin_read_DMA1_IRQ_STATUS() |
+					   DMA_DONE | DMA_ERR);
+		return IRQ_HANDLED;
+	}
+
+real_rx:
+	bf537mac_rx(dev);
+	number++;
+	goto get_one_packet;
+}
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+static void bf537mac_poll(struct net_device *dev)
+{
+	disable_irq(IRQ_MAC_RX);
+	bf537mac_interrupt(IRQ_MAC_RX, dev);
+	enable_irq(IRQ_MAC_RX);
+}
+#endif				/* CONFIG_NET_POLL_CONTROLLER */
+
+static void bf537mac_reset(void)
+{
+	unsigned int opmode;
+
+	opmode = bfin_read_EMAC_OPMODE();
+	opmode &= (~RE);
+	opmode &= (~TE);
+	/* Turn off the EMAC */
+	bfin_write_EMAC_OPMODE(opmode);
+}
+
+/*
+ * Enable Interrupts, Receive, and Transmit
+ */
+static int bf537mac_enable(struct net_device *dev)
+{
+	u32 opmode;
+
+	pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+	/* Set RX DMA */
+	bfin_write_DMA1_NEXT_DESC_PTR(&(rx_list_head->desc_a));
+	bfin_write_DMA1_CONFIG(rx_list_head->desc_a.config);
+
+	/* Wait MII done */
+	poll_mdc_done();
+
+	/* We enable only RX here */
+	/* ASTP   : Enable Automatic Pad Stripping
+	   PR     : Promiscuous Mode for test
+	   PSF    : Receive frames with total length less than 64 bytes.
+	   FDMODE : Full Duplex Mode
+	   LB     : Internal Loopback for test
+	   RE     : Receiver Enable */
+	opmode = bfin_read_EMAC_OPMODE();
+	if (opmode & FDMODE)
+		opmode |= PSF;
+	else
+		opmode |= DRO | DC | PSF;
+	opmode |= RE;
+
+#if defined(CONFIG_BFIN_MAC_RMII)
+	opmode |= RMII; /* For Now only 100MBit are supported */
+#ifdef CONFIG_BF_REV_0_2
+	opmode |= TE;
+#endif
+#endif
+	/* Turn on the EMAC rx */
+	bfin_write_EMAC_OPMODE(opmode);
+
+	return 0;
+}
+
+/* Our watchdog timed out. Called by the networking layer */
+static void bf537mac_timeout(struct net_device *dev)
+{
+	pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+	bf537mac_reset();
+
+	/* reset tx queue */
+	tx_list_tail = tx_list_head->next;
+
+	bf537mac_enable(dev);
+
+	/* We can accept TX packets again */
+	dev->trans_start = jiffies;
+	netif_wake_queue(dev);
+}
+
+/*
+ * Get the current statistics.
+ * This may be called with the card open or closed.
+ */
+static struct net_device_stats *bf537mac_query_statistics(struct net_device
+							  *dev)
+{
+	struct bf537mac_local *lp = netdev_priv(dev);
+
+	pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+	return &lp->stats;
+}
+
+/*
+ * This routine will, depending on the values passed to it,
+ * either make it accept multicast packets, go into
+ * promiscuous mode (for TCPDUMP and cousins) or accept
+ * a select set of multicast packets
+ */
+static void bf537mac_set_multicast_list(struct net_device *dev)
+{
+	u32 sysctl;
+
+	if (dev->flags & IFF_PROMISC) {
+		printk(KERN_INFO "%s: set to promisc mode\n", dev->name);
+		sysctl = bfin_read_EMAC_OPMODE();
+		sysctl |= RAF;
+		bfin_write_EMAC_OPMODE(sysctl);
+	} else if (dev->flags & IFF_ALLMULTI || dev->mc_count) {
+		/* accept all multicast */
+		sysctl = bfin_read_EMAC_OPMODE();
+		sysctl |= PAM;
+		bfin_write_EMAC_OPMODE(sysctl);
+	} else {
+		/* clear promisc or multicast mode */
+		sysctl = bfin_read_EMAC_OPMODE();
+		sysctl &= ~(RAF | PAM);
+		bfin_write_EMAC_OPMODE(sysctl);
+	}
+}
+
+/*
+ * this puts the device in an inactive state
+ */
+static void bf537mac_shutdown(struct net_device *dev)
+{
+	/* Turn off the EMAC */
+	bfin_write_EMAC_OPMODE(0x00000000);
+	/* Turn off the EMAC RX DMA */
+	bfin_write_DMA1_CONFIG(0x0000);
+	bfin_write_DMA2_CONFIG(0x0000);
+}
+
+/*
+ * Open and Initialize the interface
+ *
+ * Set up everything, reset the card, etc..
+ */
+static int bf537mac_open(struct net_device *dev)
+{
+	pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+	/*
+	 * Check that the address is valid.  If its not, refuse
+	 * to bring the device up.  The user must specify an
+	 * address using ifconfig eth0 hw ether xx:xx:xx:xx:xx:xx
+	 */
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		printk(KERN_WARNING DRV_NAME ": no valid ethernet hw addr\n");
+		return -EINVAL;
+	}
+
+	/* initial rx and tx list */
+	desc_list_init();
+
+	bf537mac_setphy(dev);
+	setup_system_regs(dev);
+	bf537mac_reset();
+	bf537mac_enable(dev);
+
+	pr_debug("hardware init finished\n");
+	netif_start_queue(dev);
+	netif_carrier_on(dev);
+
+	return 0;
+}
+
+/*
+ *
+ * this makes the board clean up everything that it can
+ * and not talk to the outside world.   Caused by
+ * an 'ifconfig ethX down'
+ */
+static int bf537mac_close(struct net_device *dev)
+{
+	pr_debug("%s: %s\n", dev->name, __FUNCTION__);
+
+	netif_stop_queue(dev);
+	netif_carrier_off(dev);
+
+	/* clear everything */
+	bf537mac_shutdown(dev);
+
+	/* free the rx/tx buffers */
+	desc_list_free();
+
+	return 0;
+}
+
+static int __init bf537mac_probe(struct net_device *dev)
+{
+	struct bf537mac_local *lp = netdev_priv(dev);
+	int retval;
+
+	/* Grab the MAC address in the MAC */
+	*(__le32 *) (&(dev->dev_addr[0])) = cpu_to_le32(bfin_read_EMAC_ADDRLO());
+	*(__le16 *) (&(dev->dev_addr[4])) = cpu_to_le16((u16) bfin_read_EMAC_ADDRHI());
+
+	/* probe mac */
+	/*todo: how to proble? which is revision_register */
+	bfin_write_EMAC_ADDRLO(0x12345678);
+	if (bfin_read_EMAC_ADDRLO() != 0x12345678) {
+		pr_debug("can't detect bf537 mac!\n");
+		retval = -ENODEV;
+		goto err_out;
+	}
+
+	/* set the GPIO pins to Ethernet mode */
+	retval = setup_pin_mux(1);
+
+	if (retval)
+		return retval;
+
+	/*Is it valid? (Did bootloader initialize it?) */
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		/* Grab the MAC from the board somehow - this is done in the
+		   arch/blackfin/mach-bf537/boards/eth_mac.c */
+		get_bf537_ether_addr(dev->dev_addr);
+	}
+
+	/* If still not valid, get a random one */
+	if (!is_valid_ether_addr(dev->dev_addr)) {
+		random_ether_addr(dev->dev_addr);
+	}
+
+	setup_mac_addr(dev->dev_addr);
+
+	/* Fill in the fields of the device structure with ethernet values. */
+	ether_setup(dev);
+
+	dev->open = bf537mac_open;
+	dev->stop = bf537mac_close;
+	dev->hard_start_xmit = bf537mac_hard_start_xmit;
+	dev->tx_timeout = bf537mac_timeout;
+	dev->get_stats = bf537mac_query_statistics;
+	dev->set_multicast_list = bf537mac_set_multicast_list;
+#ifdef CONFIG_NET_POLL_CONTROLLER
+	dev->poll_controller = bf537mac_poll;
+#endif
+
+	/* fill in some of the fields */
+	lp->version = 1;
+	lp->PhyAddr = 0x01;
+	lp->CLKIN = 25;
+	lp->FullDuplex = 0;
+	lp->Negotiate = 1;
+	lp->FlowControl = 0;
+	spin_lock_init(&lp->lock);
+
+	/* now, enable interrupts */
+	/* register irq handler */
+	if (request_irq
+	    (IRQ_MAC_RX, bf537mac_interrupt, IRQF_DISABLED | IRQF_SHARED,
+	     "BFIN537_MAC_RX", dev)) {
+		printk(KERN_WARNING DRV_NAME
+		       ": Unable to attach BlackFin MAC RX interrupt\n");
+		return -EBUSY;
+	}
+
+	/* Enable PHY output early */
+	if (!(bfin_read_VR_CTL() & PHYCLKOE))
+		bfin_write_VR_CTL(bfin_read_VR_CTL() | PHYCLKOE);
+
+	retval = register_netdev(dev);
+	if (retval == 0) {
+		/* now, print out the card info, in a short format.. */
+		printk(KERN_INFO "%s: Version %s, %s\n",
+			 DRV_NAME, DRV_VERSION, DRV_DESC);
+	}
+
+err_out:
+	return retval;
+}
+
+static int bfin_mac_probe(struct platform_device *pdev)
+{
+	struct net_device *ndev;
+
+	ndev = alloc_etherdev(sizeof(struct bf537mac_local));
+	if (!ndev) {
+		printk(KERN_WARNING DRV_NAME ": could not allocate device\n");
+		return -ENOMEM;
+	}
+
+	SET_MODULE_OWNER(ndev);
+	SET_NETDEV_DEV(ndev, &pdev->dev);
+
+	platform_set_drvdata(pdev, ndev);
+
+	if (bf537mac_probe(ndev) != 0) {
+		platform_set_drvdata(pdev, NULL);
+		free_netdev(ndev);
+		printk(KERN_WARNING DRV_NAME ": not found\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+static int bfin_mac_remove(struct platform_device *pdev)
+{
+	struct net_device *ndev = platform_get_drvdata(pdev);
+
+	platform_set_drvdata(pdev, NULL);
+
+	unregister_netdev(ndev);
+
+	free_irq(IRQ_MAC_RX, ndev);
+
+	free_netdev(ndev);
+
+	setup_pin_mux(0);
+
+	return 0;
+}
+
+static int bfin_mac_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	return 0;
+}
+
+static int bfin_mac_resume(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver bfin_mac_driver = {
+	.probe = bfin_mac_probe,
+	.remove = bfin_mac_remove,
+	.resume = bfin_mac_resume,
+	.suspend = bfin_mac_suspend,
+	.driver = {
+		   .name = DRV_NAME,
+		   },
+};
+
+static int __init bfin_mac_init(void)
+{
+	return platform_driver_register(&bfin_mac_driver);
+}
+
+module_init(bfin_mac_init);
+
+static void __exit bfin_mac_cleanup(void)
+{
+	platform_driver_unregister(&bfin_mac_driver);
+}
+
+module_exit(bfin_mac_cleanup);
diff --git a/drivers/net/bfin_mac.h b/drivers/net/bfin_mac.h
new file mode 100644
index 000000000000..af87189b85fa
--- /dev/null
+++ b/drivers/net/bfin_mac.h
@@ -0,0 +1,132 @@
+/*
+ * File:	drivers/net/bfin_mac.c
+ * Based on:
+ * Maintainer:
+ * 		Bryan Wu <bryan.wu@analog.com>
+ *
+ * Original author:
+ * 		Luke Yang <luke.yang@analog.com>
+ *
+ * Created:
+ * Description:
+ *
+ * Modified:
+ *		Copyright 2004-2006 Analog Devices Inc.
+ *
+ * Bugs:	Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software ;  you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation ;  either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY ;  without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program ;  see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+/*
+ * PHY REGISTER NAMES
+ */
+#define PHYREG_MODECTL		0x0000
+#define PHYREG_MODESTAT		0x0001
+#define PHYREG_PHYID1		0x0002
+#define PHYREG_PHYID2		0x0003
+#define PHYREG_ANAR		0x0004
+#define PHYREG_ANLPAR		0x0005
+#define PHYREG_ANER		0x0006
+#define PHYREG_NSR		0x0010
+#define PHYREG_LBREMR		0x0011
+#define PHYREG_REC		0x0012
+#define PHYREG_10CFG		0x0013
+#define PHYREG_PHY1_1		0x0014
+#define PHYREG_PHY1_2		0x0015
+#define PHYREG_PHY2		0x0016
+#define PHYREG_TW_1		0x0017
+#define PHYREG_TW_2		0x0018
+#define PHYREG_TEST		0x0019
+
+#define PHY_RESET		0x8000
+#define PHY_ANEG_EN		0x1000
+#define PHY_DUPLEX		0x0100
+#define PHY_SPD_SET		0x2000
+
+#define BFIN_MAC_CSUM_OFFLOAD
+
+struct dma_descriptor {
+	struct dma_descriptor *next_dma_desc;
+	unsigned long start_addr;
+	unsigned short config;
+	unsigned short x_count;
+};
+
+struct status_area_rx {
+#if defined(BFIN_MAC_CSUM_OFFLOAD)
+	unsigned short ip_hdr_csum;	/* ip header checksum */
+	/* ip payload(udp or tcp or others) checksum */
+	unsigned short ip_payload_csum;
+#endif
+	unsigned long status_word;	/* the frame status word */
+};
+
+struct status_area_tx {
+	unsigned long status_word;	/* the frame status word */
+};
+
+/* use two descriptors for a packet */
+struct net_dma_desc_rx {
+	struct net_dma_desc_rx *next;
+	struct sk_buff *skb;
+	struct dma_descriptor desc_a;
+	struct dma_descriptor desc_b;
+	struct status_area_rx status;
+};
+
+/* use two descriptors for a packet */
+struct net_dma_desc_tx {
+	struct net_dma_desc_tx *next;
+	struct sk_buff *skb;
+	struct dma_descriptor desc_a;
+	struct dma_descriptor desc_b;
+	unsigned char packet[1560];
+	struct status_area_tx status;
+};
+
+struct bf537mac_local {
+	/*
+	 * these are things that the kernel wants me to keep, so users
+	 * can find out semi-useless statistics of how well the card is
+	 * performing
+	 */
+	struct net_device_stats stats;
+
+	int version;
+
+	int FlowEnabled;	/* record if data flow is active */
+	int EtherIntIVG;	/* IVG for the ethernet interrupt */
+	int RXIVG;		/* IVG for the RX completion */
+	int TXIVG;		/* IVG for the TX completion */
+	int PhyAddr;		/* PHY address */
+	int OpMode;		/* set these bits n the OPMODE regs */
+	int Port10;		/* set port speed to 10 Mbit/s */
+	int GenChksums;		/* IP checksums to be calculated */
+	int NoRcveLnth;		/* dont insert recv length at start of buffer */
+	int StripPads;		/* remove trailing pad bytes */
+	int FullDuplex;		/* set full duplex mode */
+	int Negotiate;		/* enable auto negotiation */
+	int Loopback;		/* loopback at the PHY */
+	int Cache;		/* Buffers may be cached */
+	int FlowControl;	/* flow control active */
+	int CLKIN;		/* clock in value in MHZ */
+	unsigned short IntMask;	/* interrupt mask */
+	unsigned char Mac[6];	/* MAC address of the board */
+	spinlock_t lock;
+};
+
+extern void get_bf537_ether_addr(char *addr);
diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h
index 6628fa622e2c..489c8b260dd8 100644
--- a/drivers/net/ehea/ehea.h
+++ b/drivers/net/ehea/ehea.h
@@ -39,7 +39,7 @@
 #include <asm/io.h>
 
 #define DRV_NAME	"ehea"
-#define DRV_VERSION	"EHEA_0070"
+#define DRV_VERSION	"EHEA_0071"
 
 /* eHEA capability flags */
 #define DLPAR_PORT_ADD_REM 1
diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c
index 1d1571cf322e..4c70a9301c1b 100644
--- a/drivers/net/ehea/ehea_main.c
+++ b/drivers/net/ehea/ehea_main.c
@@ -466,6 +466,8 @@ static struct ehea_cqe *ehea_proc_rwqes(struct net_device *dev,
 							 cqe->vlan_tag);
 			else
 				netif_receive_skb(skb);
+
+			dev->last_rx = jiffies;
 		} else {
 			pr->p_stats.poll_receive_errors++;
 			port_reset = ehea_treat_poll_error(pr, rq, cqe,
@@ -1433,7 +1435,8 @@ static int ehea_broadcast_reg_helper(struct ehea_port *port, u32 hcallid)
 				     port->logical_port_id,
 				     reg_type, port->mac_addr, 0, hcallid);
 	if (hret != H_SUCCESS) {
-		ehea_error("reg_dereg_bcmc failed (tagged)");
+		ehea_error("%sregistering bc address failed (tagged)",
+                           hcallid == H_REG_BCMC ? "" : "de");
 		ret = -EIO;
 		goto out_herr;
 	}
@@ -1444,7 +1447,8 @@ static int ehea_broadcast_reg_helper(struct ehea_port *port, u32 hcallid)
 				     port->logical_port_id,
 				     reg_type, port->mac_addr, 0, hcallid);
 	if (hret != H_SUCCESS) {
-		ehea_error("reg_dereg_bcmc failed (vlan)");
+		ehea_error("%sregistering bc address failed (vlan)",
+			   hcallid == H_REG_BCMC ? "" : "de");
 		ret = -EIO;
 	}
 out_herr:
@@ -2170,7 +2174,6 @@ static int ehea_up(struct net_device *dev)
 {
 	int ret, i;
 	struct ehea_port *port = netdev_priv(dev);
-	u64 mac_addr = 0;
 
 	if (port->state == EHEA_PORT_UP)
 		return 0;
@@ -2189,18 +2192,10 @@ static int ehea_up(struct net_device *dev)
 		goto out_clean_pr;
 	}
 
-	ret = ehea_broadcast_reg_helper(port, H_REG_BCMC);
-	if (ret) {
-		ret = -EIO;
-		ehea_error("out_clean_pr");
-		goto out_clean_pr;
-	}
-	mac_addr = (*(u64*)dev->dev_addr) >> 16;
-
 	ret = ehea_reg_interrupts(dev);
 	if (ret) {
-		ehea_error("out_dereg_bc");
-		goto out_dereg_bc;
+		ehea_error("reg_interrupts failed. ret:%d", ret);
+		goto out_clean_pr;
 	}
 
 	for(i = 0; i < port->num_def_qps + port->num_add_tx_qps; i++) {
@@ -2226,9 +2221,6 @@ static int ehea_up(struct net_device *dev)
 out_free_irqs:
 	ehea_free_interrupts(dev);
 
-out_dereg_bc:
-	ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
-
 out_clean_pr:
 	ehea_clean_all_portres(port);
 out:
@@ -2273,7 +2265,6 @@ static int ehea_down(struct net_device *dev)
 				&port->port_res[i].d_netdev->state))
 			msleep(1);
 
-	ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
 	port->state = EHEA_PORT_DOWN;
 
 	ret = ehea_clean_all_portres(port);
@@ -2655,12 +2646,18 @@ struct ehea_port *ehea_setup_single_port(struct ehea_adapter *adapter,
 
 	INIT_WORK(&port->reset_task, ehea_reset_port);
 
+	ret = ehea_broadcast_reg_helper(port, H_REG_BCMC);
+	if (ret) {
+		ret = -EIO;
+		goto out_unreg_port;
+	}
+
 	ehea_set_ethtool_ops(dev);
 
 	ret = register_netdev(dev);
 	if (ret) {
 		ehea_error("register_netdev failed. ret=%d", ret);
-		goto out_unreg_port;
+		goto out_dereg_bc;
 	}
 
 	ret = ehea_get_jumboframe_status(port, &jumbo);
@@ -2675,6 +2672,9 @@ struct ehea_port *ehea_setup_single_port(struct ehea_adapter *adapter,
 
 	return port;
 
+out_dereg_bc:
+	ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
+
 out_unreg_port:
 	ehea_unregister_port(port);
 
@@ -2694,6 +2694,7 @@ static void ehea_shutdown_single_port(struct ehea_port *port)
 {
 	unregister_netdev(port->netdev);
 	ehea_unregister_port(port);
+	ehea_broadcast_reg_helper(port, H_DEREG_BCMC);
 	kfree(port->mc_list);
 	free_netdev(port->netdev);
 	port->adapter->active_ports--;
diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c
index d7a1a58de766..f92690555dd9 100644
--- a/drivers/net/gianfar.c
+++ b/drivers/net/gianfar.c
@@ -420,8 +420,18 @@ static phy_interface_t gfar_get_interface(struct net_device *dev)
 	if (ecntrl & ECNTRL_REDUCED_MODE) {
 		if (ecntrl & ECNTRL_REDUCED_MII_MODE)
 			return PHY_INTERFACE_MODE_RMII;
-		else
+		else {
+			phy_interface_t interface = priv->einfo->interface;
+
+			/*
+			 * This isn't autodetected right now, so it must
+			 * be set by the device tree or platform code.
+			 */
+			if (interface == PHY_INTERFACE_MODE_RGMII_ID)
+				return PHY_INTERFACE_MODE_RGMII_ID;
+
 			return PHY_INTERFACE_MODE_RGMII;
+		}
 	}
 
 	if (priv->einfo->device_flags & FSL_GIANFAR_DEV_HAS_GIGABIT)
diff --git a/drivers/net/ni5010.c b/drivers/net/ni5010.c
index 3d5b4232f65f..22a3b3dc7d89 100644
--- a/drivers/net/ni5010.c
+++ b/drivers/net/ni5010.c
@@ -670,14 +670,10 @@ static void ni5010_set_multicast_list(struct net_device *dev)
 
 	PRINTK2((KERN_DEBUG "%s: entering set_multicast_list\n", dev->name));
 
-	if (dev->flags&IFF_PROMISC || dev->flags&IFF_ALLMULTI) {
+	if (dev->flags&IFF_PROMISC || dev->flags&IFF_ALLMULTI || dev->mc_list) {
 		dev->flags |= IFF_PROMISC;
 		outb(RMD_PROMISC, EDLC_RMODE); /* Enable promiscuous mode */
 		PRINTK((KERN_DEBUG "%s: Entering promiscuous mode\n", dev->name));
-	} else if (dev->mc_list) {
-		/* Sorry, multicast not supported */
-		PRINTK((KERN_DEBUG "%s: No multicast, entering broadcast mode\n", dev->name));
-		outb(RMD_BROADCAST, EDLC_RMODE);
 	} else {
 		PRINTK((KERN_DEBUG "%s: Entering broadcast mode\n", dev->name));
 		outb(RMD_BROADCAST, EDLC_RMODE);  /* Disable promiscuous mode, use normal mode */
diff --git a/drivers/net/ns83820.c b/drivers/net/ns83820.c
index 104aab3c957f..ea80e6cb3dec 100644
--- a/drivers/net/ns83820.c
+++ b/drivers/net/ns83820.c
@@ -1582,7 +1582,7 @@ static void ns83820_set_multicast(struct net_device *ndev)
 	else
 		and_mask &= ~(RFCR_AAU | RFCR_AAM);
 
-	if (ndev->flags & IFF_ALLMULTI)
+	if (ndev->flags & IFF_ALLMULTI || ndev->mc_count)
 		or_mask |= RFCR_AAM;
 	else
 		and_mask &= ~RFCR_AAM;
diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c
index 596222b260d6..6a5385647911 100644
--- a/drivers/net/phy/vitesse.c
+++ b/drivers/net/phy/vitesse.c
@@ -21,6 +21,10 @@
 /* Vitesse Extended Control Register 1 */
 #define MII_VSC8244_EXT_CON1           0x17
 #define MII_VSC8244_EXTCON1_INIT       0x0000
+#define MII_VSC8244_EXTCON1_TX_SKEW_MASK	0x0c00
+#define MII_VSC8244_EXTCON1_RX_SKEW_MASK	0x0300
+#define MII_VSC8244_EXTCON1_TX_SKEW	0x0800
+#define MII_VSC8244_EXTCON1_RX_SKEW	0x0200
 
 /* Vitesse Interrupt Mask Register */
 #define MII_VSC8244_IMASK		0x19
@@ -39,7 +43,7 @@
 
 /* Vitesse Auxiliary Control/Status Register */
 #define MII_VSC8244_AUX_CONSTAT        	0x1c
-#define MII_VSC8244_AUXCONSTAT_INIT    	0x0004
+#define MII_VSC8244_AUXCONSTAT_INIT    	0x0000
 #define MII_VSC8244_AUXCONSTAT_DUPLEX  	0x0020
 #define MII_VSC8244_AUXCONSTAT_SPEED   	0x0018
 #define MII_VSC8244_AUXCONSTAT_GBIT    	0x0010
@@ -51,6 +55,7 @@ MODULE_LICENSE("GPL");
 
 static int vsc824x_config_init(struct phy_device *phydev)
 {
+	int extcon;
 	int err;
 
 	err = phy_write(phydev, MII_VSC8244_AUX_CONSTAT,
@@ -58,14 +63,34 @@ static int vsc824x_config_init(struct phy_device *phydev)
 	if (err < 0)
 		return err;
 
-	err = phy_write(phydev, MII_VSC8244_EXT_CON1,
-			MII_VSC8244_EXTCON1_INIT);
+	extcon = phy_read(phydev, MII_VSC8244_EXT_CON1);
+
+	if (extcon < 0)
+		return err;
+
+	extcon &= ~(MII_VSC8244_EXTCON1_TX_SKEW_MASK |
+			MII_VSC8244_EXTCON1_RX_SKEW_MASK);
+
+	if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)
+		extcon |= (MII_VSC8244_EXTCON1_TX_SKEW |
+				MII_VSC8244_EXTCON1_RX_SKEW);
+
+	err = phy_write(phydev, MII_VSC8244_EXT_CON1, extcon);
+
 	return err;
 }
 
 static int vsc824x_ack_interrupt(struct phy_device *phydev)
 {
-	int err = phy_read(phydev, MII_VSC8244_ISTAT);
+	int err = 0;
+	
+	/*
+	 * Don't bother to ACK the interrupts if interrupts
+	 * are disabled.  The 824x cannot clear the interrupts
+	 * if they are disabled.
+	 */
+	if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
+		err = phy_read(phydev, MII_VSC8244_ISTAT);
 
 	return (err < 0) ? err : 0;
 }
@@ -77,8 +102,19 @@ static int vsc824x_config_intr(struct phy_device *phydev)
 	if (phydev->interrupts == PHY_INTERRUPT_ENABLED)
 		err = phy_write(phydev, MII_VSC8244_IMASK,
 				MII_VSC8244_IMASK_MASK);
-	else
+	else {
+		/*
+		 * The Vitesse PHY cannot clear the interrupt
+		 * once it has disabled them, so we clear them first
+		 */
+		err = phy_read(phydev, MII_VSC8244_ISTAT);
+
+		if (err)
+			return err;
+
 		err = phy_write(phydev, MII_VSC8244_IMASK, 0);
+	}
+
 	return err;
 }
 
diff --git a/drivers/net/saa9730.c b/drivers/net/saa9730.c
index 451486b32f23..7dae4d404978 100644
--- a/drivers/net/saa9730.c
+++ b/drivers/net/saa9730.c
@@ -940,15 +940,14 @@ static void lan_saa9730_set_multicast(struct net_device *dev)
 		       CAM_CONTROL_GROUP_ACC | CAM_CONTROL_BROAD_ACC,
 		       &lp->lan_saa9730_regs->CamCtl);
 	} else {
-		if (dev->flags & IFF_ALLMULTI) {
+		if (dev->flags & IFF_ALLMULTI || dev->mc_count) {
 			/* accept all multicast packets */
-			writel(CAM_CONTROL_COMP_EN | CAM_CONTROL_GROUP_ACC |
-			       CAM_CONTROL_BROAD_ACC,
-			       &lp->lan_saa9730_regs->CamCtl);
-		} else {
 			/*
 			 * Will handle the multicast stuff later. -carstenl
 			 */
+			writel(CAM_CONTROL_COMP_EN | CAM_CONTROL_GROUP_ACC |
+			       CAM_CONTROL_BROAD_ACC,
+			       &lp->lan_saa9730_regs->CamCtl);
 		}
 	}
 
diff --git a/drivers/net/tc35815.c b/drivers/net/tc35815.c
index 75655add3f34..7f94ca930988 100644
--- a/drivers/net/tc35815.c
+++ b/drivers/net/tc35815.c
@@ -626,7 +626,7 @@ static int __devinit tc35815_read_plat_dev_addr(struct net_device *dev)
 	return -ENODEV;
 }
 #else
-static int __devinit tc35815_read_plat_dev_addr(struct device *dev)
+static int __devinit tc35815_read_plat_dev_addr(struct net_device *dev)
 {
 	return -ENODEV;
 }
diff --git a/drivers/net/wireless/ipw2100.c b/drivers/net/wireless/ipw2100.c
index 072ede71e575..8990585bd228 100644
--- a/drivers/net/wireless/ipw2100.c
+++ b/drivers/net/wireless/ipw2100.c
@@ -7868,10 +7868,10 @@ static int ipw2100_wx_set_powermode(struct net_device *dev,
 		goto done;
 	}
 
-	if ((mode < 1) || (mode > POWER_MODES))
+	if ((mode < 0) || (mode > POWER_MODES))
 		mode = IPW_POWER_AUTO;
 
-	if (priv->power_mode != mode)
+	if (IPW_POWER_LEVEL(priv->power_mode) != mode)
 		err = ipw2100_set_power_mode(priv, mode);
       done:
 	mutex_unlock(&priv->action_mutex);
@@ -7902,7 +7902,7 @@ static int ipw2100_wx_get_powermode(struct net_device *dev,
 			break;
 		case IPW_POWER_AUTO:
 			snprintf(extra, MAX_POWER_STRING,
-				 "Power save level: %d (Auto)", 0);
+				 "Power save level: %d (Auto)", level);
 			break;
 		default:
 			timeout = timeout_duration[level - 1] / 1000;
diff --git a/drivers/net/wireless/ipw2200.c b/drivers/net/wireless/ipw2200.c
index aa32a97380ec..61497c467467 100644
--- a/drivers/net/wireless/ipw2200.c
+++ b/drivers/net/wireless/ipw2200.c
@@ -70,7 +70,7 @@
 #define VQ
 #endif
 
-#define IPW2200_VERSION "1.2.0" VK VD VM VP VR VQ
+#define IPW2200_VERSION "1.2.2" VK VD VM VP VR VQ
 #define DRV_DESCRIPTION	"Intel(R) PRO/Wireless 2200/2915 Network Driver"
 #define DRV_COPYRIGHT	"Copyright(c) 2003-2006 Intel Corporation"
 #define DRV_VERSION     IPW2200_VERSION
@@ -2506,7 +2506,7 @@ static int ipw_send_power_mode(struct ipw_priv *priv, u32 mode)
 		break;
 	}
 
-	param = cpu_to_le32(mode);
+	param = cpu_to_le32(param);
 	return ipw_send_cmd_pdu(priv, IPW_CMD_POWER_MODE, sizeof(param),
 				&param);
 }
@@ -9568,6 +9568,7 @@ static int ipw_wx_set_power(struct net_device *dev,
 		priv->power_mode = IPW_POWER_ENABLED | IPW_POWER_BATTERY;
 	else
 		priv->power_mode = IPW_POWER_ENABLED | priv->power_mode;
+
 	err = ipw_send_power_mode(priv, IPW_POWER_LEVEL(priv->power_mode));
 	if (err) {
 		IPW_DEBUG_WX("failed setting power mode.\n");
@@ -9604,22 +9605,19 @@ static int ipw_wx_set_powermode(struct net_device *dev,
 	struct ipw_priv *priv = ieee80211_priv(dev);
 	int mode = *(int *)extra;
 	int err;
+
 	mutex_lock(&priv->mutex);
-	if ((mode < 1) || (mode > IPW_POWER_LIMIT)) {
+	if ((mode < 1) || (mode > IPW_POWER_LIMIT))
 		mode = IPW_POWER_AC;
-		priv->power_mode = mode;
-	} else {
-		priv->power_mode = IPW_POWER_ENABLED | mode;
-	}
 
-	if (priv->power_mode != mode) {
+	if (IPW_POWER_LEVEL(priv->power_mode) != mode) {
 		err = ipw_send_power_mode(priv, mode);
-
 		if (err) {
 			IPW_DEBUG_WX("failed setting power mode.\n");
 			mutex_unlock(&priv->mutex);
 			return err;
 		}
+		priv->power_mode = IPW_POWER_ENABLED | mode;
 	}
 	mutex_unlock(&priv->mutex);
 	return 0;
@@ -10555,7 +10553,7 @@ static irqreturn_t ipw_isr(int irq, void *data)
 	spin_lock(&priv->irq_lock);
 
 	if (!(priv->status & STATUS_INT_ENABLED)) {
-		/* Shared IRQ */
+		/* IRQ is disabled */
 		goto none;
 	}
 
diff --git a/drivers/net/wireless/zd1211rw/zd_usb.c b/drivers/net/wireless/zd1211rw/zd_usb.c
index 28d41a29d7b1..a9c339ef116a 100644
--- a/drivers/net/wireless/zd1211rw/zd_usb.c
+++ b/drivers/net/wireless/zd1211rw/zd_usb.c
@@ -72,6 +72,8 @@ static struct usb_device_id usb_ids[] = {
 	{ USB_DEVICE(0x0586, 0x3413), .driver_info = DEVICE_ZD1211B },
 	{ USB_DEVICE(0x0053, 0x5301), .driver_info = DEVICE_ZD1211B },
 	{ USB_DEVICE(0x0411, 0x00da), .driver_info = DEVICE_ZD1211B },
+	{ USB_DEVICE(0x2019, 0x5303), .driver_info = DEVICE_ZD1211B },
+	{ USB_DEVICE(0x129b, 0x1667), .driver_info = DEVICE_ZD1211B },
 	/* "Driverless" devices that need ejecting */
 	{ USB_DEVICE(0x0ace, 0x2011), .driver_info = DEVICE_INSTALLER },
 	{ USB_DEVICE(0x0ace, 0x20ff), .driver_info = DEVICE_INSTALLER },