Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 137 insertions, 0 deletions

diff --git a/include/linux/fdreg.h b/include/linux/fdreg.h
new file mode 100644
index 000000000000..c2eeb63b72db
--- /dev/null
+++ b/include/linux/fdreg.h
@@ -0,0 +1,137 @@
+#ifndef _LINUX_FDREG_H
+#define _LINUX_FDREG_H
+/*
+ * This file contains some defines for the floppy disk controller.
+ * Various sources. Mostly "IBM Microcomputers: A Programmers
+ * Handbook", Sanches and Canton.
+ */
+
+#ifdef FDPATCHES
+#define FD_IOPORT fdc_state[fdc].address
+#else
+/* It would be a lot saner just to force fdc_state[fdc].address to always
+   be set ! FIXME */
+#define FD_IOPORT 0x3f0
+#endif
+
+/* Fd controller regs. S&C, about page 340 */
+#define FD_STATUS	(4 + FD_IOPORT )
+#define FD_DATA		(5 + FD_IOPORT )
+
+/* Digital Output Register */
+#define FD_DOR		(2 + FD_IOPORT )
+
+/* Digital Input Register (read) */
+#define FD_DIR		(7 + FD_IOPORT )
+
+/* Diskette Control Register (write)*/
+#define FD_DCR		(7 + FD_IOPORT )
+
+/* Bits of main status register */
+#define STATUS_BUSYMASK	0x0F		/* drive busy mask */
+#define STATUS_BUSY	0x10		/* FDC busy */
+#define STATUS_DMA	0x20		/* 0- DMA mode */
+#define STATUS_DIR	0x40		/* 0- cpu->fdc */
+#define STATUS_READY	0x80		/* Data reg ready */
+
+/* Bits of FD_ST0 */
+#define ST0_DS		0x03		/* drive select mask */
+#define ST0_HA		0x04		/* Head (Address) */
+#define ST0_NR		0x08		/* Not Ready */
+#define ST0_ECE		0x10		/* Equipment check error */
+#define ST0_SE		0x20		/* Seek end */
+#define ST0_INTR	0xC0		/* Interrupt code mask */
+
+/* Bits of FD_ST1 */
+#define ST1_MAM		0x01		/* Missing Address Mark */
+#define ST1_WP		0x02		/* Write Protect */
+#define ST1_ND		0x04		/* No Data - unreadable */
+#define ST1_OR		0x10		/* OverRun */
+#define ST1_CRC		0x20		/* CRC error in data or addr */
+#define ST1_EOC		0x80		/* End Of Cylinder */
+
+/* Bits of FD_ST2 */
+#define ST2_MAM		0x01		/* Missing Address Mark (again) */
+#define ST2_BC		0x02		/* Bad Cylinder */
+#define ST2_SNS		0x04		/* Scan Not Satisfied */
+#define ST2_SEH		0x08		/* Scan Equal Hit */
+#define ST2_WC		0x10		/* Wrong Cylinder */
+#define ST2_CRC		0x20		/* CRC error in data field */
+#define ST2_CM		0x40		/* Control Mark = deleted */
+
+/* Bits of FD_ST3 */
+#define ST3_HA		0x04		/* Head (Address) */
+#define ST3_DS		0x08		/* drive is double-sided */
+#define ST3_TZ		0x10		/* Track Zero signal (1=track 0) */
+#define ST3_RY		0x20		/* drive is ready */
+#define ST3_WP		0x40		/* Write Protect */
+#define ST3_FT		0x80		/* Drive Fault */
+
+/* Values for FD_COMMAND */
+#define FD_RECALIBRATE		0x07	/* move to track 0 */
+#define FD_SEEK			0x0F	/* seek track */
+#define FD_READ			0xE6	/* read with MT, MFM, SKip deleted */
+#define FD_WRITE		0xC5	/* write with MT, MFM */
+#define FD_SENSEI		0x08	/* Sense Interrupt Status */
+#define FD_SPECIFY		0x03	/* specify HUT etc */
+#define FD_FORMAT		0x4D	/* format one track */
+#define FD_VERSION		0x10	/* get version code */
+#define FD_CONFIGURE		0x13	/* configure FIFO operation */
+#define FD_PERPENDICULAR	0x12	/* perpendicular r/w mode */
+#define FD_GETSTATUS		0x04	/* read ST3 */
+#define FD_DUMPREGS		0x0E	/* dump the contents of the fdc regs */
+#define FD_READID		0xEA	/* prints the header of a sector */
+#define FD_UNLOCK		0x14	/* Fifo config unlock */
+#define FD_LOCK			0x94	/* Fifo config lock */
+#define FD_RSEEK_OUT		0x8f	/* seek out (i.e. to lower tracks) */
+#define FD_RSEEK_IN		0xcf	/* seek in (i.e. to higher tracks) */
+
+/* the following commands are new in the 82078. They are not used in the
+ * floppy driver, except the first three. These commands may be useful for apps
+ * which use the FDRAWCMD interface. For doc, get the 82078 spec sheets at
+ * http://www-techdoc.intel.com/docs/periph/fd_contr/datasheets/ */
+
+#define FD_PARTID		0x18	/* part id ("extended" version cmd) */
+#define FD_SAVE			0x2e	/* save fdc regs for later restore */
+#define FD_DRIVESPEC		0x8e	/* drive specification: Access to the
+					 * 2 Mbps data transfer rate for tape
+					 * drives */
+
+#define FD_RESTORE		0x4e    /* later restore */
+#define FD_POWERDOWN		0x27	/* configure FDC's powersave features */
+#define FD_FORMAT_N_WRITE	0xef    /* format and write in one go. */
+#define FD_OPTION		0x33	/* ISO format (which is a clean way to
+					 * pack more sectors on a track) */
+
+/* DMA commands */
+#define DMA_READ	0x46
+#define DMA_WRITE	0x4A
+
+/* FDC version return types */
+#define FDC_NONE	0x00
+#define FDC_UNKNOWN	0x10	/* DO NOT USE THIS TYPE EXCEPT IF IDENTIFICATION
+				   FAILS EARLY */
+#define FDC_8272A	0x20	/* Intel 8272a, NEC 765 */
+#define FDC_765ED	0x30	/* Non-Intel 1MB-compatible FDC, can't detect */
+#define FDC_82072	0x40	/* Intel 82072; 8272a + FIFO + DUMPREGS */
+#define FDC_82072A	0x45	/* 82072A (on Sparcs) */
+#define FDC_82077_ORIG	0x51	/* Original version of 82077AA, sans LOCK */
+#define FDC_82077	0x52	/* 82077AA-1 */
+#define FDC_82078_UNKN	0x5f	/* Unknown 82078 variant */
+#define FDC_82078	0x60	/* 44pin 82078 or 64pin 82078SL */
+#define FDC_82078_1	0x61	/* 82078-1 (2Mbps fdc) */
+#define FDC_S82078B	0x62	/* S82078B (first seen on Adaptec AVA-2825 VLB
+				 * SCSI/EIDE/Floppy controller) */
+#define FDC_87306	0x63	/* National Semiconductor PC 87306 */
+
+/*
+ * Beware: the fdc type list is roughly sorted by increasing features.
+ * Presence of features is tested by comparing the FDC version id with the
+ * "oldest" version that has the needed feature.
+ * If during FDC detection, an obscure test fails late in the sequence, don't
+ * assign FDC_UNKNOWN. Else the FDC will be treated as a dumb 8272a, or worse.
+ * This is especially true if the tests are unneeded.
+ */
+
+#define FD_RESET_DELAY 20
+#endif