Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next

John W. Linville says:

====================
This is a batch of updates intended for 3.12.  It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).

The usual suspects are mostly represented.  There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there.  I don't think there is much unusual
here, FWIW.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

6 files changed, 431 insertions, 46 deletions

diff --git a/include/linux/bcma/bcma.h b/include/linux/bcma/bcma.h
index 622fc505d3e1..4d043c30216f 100644
--- a/include/linux/bcma/bcma.h
+++ b/include/linux/bcma/bcma.h
@@ -72,7 +72,19 @@ struct bcma_host_ops {
 /* Core-ID values. */
 #define BCMA_CORE_OOB_ROUTER		0x367	/* Out of band */
 #define BCMA_CORE_4706_CHIPCOMMON	0x500
+#define BCMA_CORE_PCIEG2		0x501
+#define BCMA_CORE_DMA			0x502
+#define BCMA_CORE_SDIO3			0x503
+#define BCMA_CORE_USB20			0x504
+#define BCMA_CORE_USB30			0x505
+#define BCMA_CORE_A9JTAG		0x506
+#define BCMA_CORE_DDR23			0x507
+#define BCMA_CORE_ROM			0x508
+#define BCMA_CORE_NAND			0x509
+#define BCMA_CORE_QSPI			0x50A
+#define BCMA_CORE_CHIPCOMMON_B		0x50B
 #define BCMA_CORE_4706_SOC_RAM		0x50E
+#define BCMA_CORE_ARMCA9		0x510
 #define BCMA_CORE_4706_MAC_GBIT		0x52D
 #define BCMA_CORE_AMEMC			0x52E	/* DDR1/2 memory controller core */
 #define BCMA_CORE_ALTA			0x534	/* I2S core */
@@ -177,6 +189,11 @@ struct bcma_host_ops {
 #define  BCMA_PKG_ID_BCM5357	11
 #define BCMA_CHIP_ID_BCM53572	53572
 #define  BCMA_PKG_ID_BCM47188	9
+#define BCMA_CHIP_ID_BCM4707	53010
+#define  BCMA_PKG_ID_BCM4707	1
+#define  BCMA_PKG_ID_BCM4708	2
+#define  BCMA_PKG_ID_BCM4709	0
+#define BCMA_CHIP_ID_BCM53018	53018
 
 /* Board types (on PCI usually equals to the subsystem dev id) */
 /* BCM4313 */
diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h
index 4e101af9c1ff..8def09e55f0c 100644
--- a/include/linux/ieee80211.h
+++ b/include/linux/ieee80211.h
@@ -1710,6 +1710,10 @@ enum ieee80211_eid {
 	WLAN_EID_OPMODE_NOTIF = 199,
 	WLAN_EID_WIDE_BW_CHANNEL_SWITCH = 194,
 	WLAN_EID_CHANNEL_SWITCH_WRAPPER = 196,
+	WLAN_EID_EXTENDED_BSS_LOAD = 193,
+	WLAN_EID_VHT_TX_POWER_ENVELOPE = 195,
+	WLAN_EID_AID = 197,
+	WLAN_EID_QUIET_CHANNEL = 198,
 
 	/* 802.11ad */
 	WLAN_EID_NON_TX_BSSID_CAP =  83,
@@ -1861,6 +1865,11 @@ enum ieee80211_tdls_actioncode {
 	WLAN_TDLS_DISCOVERY_REQUEST = 10,
 };
 
+/* Interworking capabilities are set in 7th bit of 4th byte of the
+ * @WLAN_EID_EXT_CAPABILITY information element
+ */
+#define WLAN_EXT_CAPA4_INTERWORKING_ENABLED	BIT(7)
+
 /*
  * TDLS capabililites to be enabled in the 5th byte of the
  * @WLAN_EID_EXT_CAPABILITY information element
diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index f49de283f50e..635e396b25b2 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -461,6 +461,33 @@ ieee80211_chandef_rate_flags(struct cfg80211_chan_def *chandef)
 }
 
 /**
+ * ieee80211_chandef_max_power - maximum transmission power for the chandef
+ *
+ * In some regulations, the transmit power may depend on the configured channel
+ * bandwidth which may be defined as dBm/MHz. This function returns the actual
+ * max_power for non-standard (20 MHz) channels.
+ *
+ * @chandef: channel definition for the channel
+ *
+ * Returns: maximum allowed transmission power in dBm for the chandef
+ */
+static inline int
+ieee80211_chandef_max_power(struct cfg80211_chan_def *chandef)
+{
+	switch (chandef->width) {
+	case NL80211_CHAN_WIDTH_5:
+		return min(chandef->chan->max_reg_power - 6,
+			   chandef->chan->max_power);
+	case NL80211_CHAN_WIDTH_10:
+		return min(chandef->chan->max_reg_power - 3,
+			   chandef->chan->max_power);
+	default:
+		break;
+	}
+	return chandef->chan->max_power;
+}
+
+/**
  * enum survey_info_flags - survey information flags
  *
  * @SURVEY_INFO_NOISE_DBM: noise (in dBm) was filled in
@@ -490,7 +517,7 @@ enum survey_info_flags {
  * @channel: the channel this survey record reports, mandatory
  * @filled: bitflag of flags from &enum survey_info_flags
  * @noise: channel noise in dBm. This and all following fields are
- *     optional
+ *	optional
  * @channel_time: amount of time in ms the radio spent on the channel
  * @channel_time_busy: amount of time the primary channel was sensed busy
  * @channel_time_ext_busy: amount of time the extension channel was sensed busy
@@ -546,9 +573,9 @@ struct cfg80211_crypto_settings {
 /**
  * struct cfg80211_beacon_data - beacon data
  * @head: head portion of beacon (before TIM IE)
- *     or %NULL if not changed
+ *	or %NULL if not changed
  * @tail: tail portion of beacon (after TIM IE)
- *     or %NULL if not changed
+ *	or %NULL if not changed
  * @head_len: length of @head
  * @tail_len: length of @tail
  * @beacon_ies: extra information element(s) to add into Beacon frames or %NULL
@@ -639,6 +666,30 @@ struct cfg80211_ap_settings {
 };
 
 /**
+ * struct cfg80211_csa_settings - channel switch settings
+ *
+ * Used for channel switch
+ *
+ * @chandef: defines the channel to use after the switch
+ * @beacon_csa: beacon data while performing the switch
+ * @counter_offset_beacon: offset for the counter within the beacon (tail)
+ * @counter_offset_presp: offset for the counter within the probe response
+ * @beacon_after: beacon data to be used on the new channel
+ * @radar_required: whether radar detection is required on the new channel
+ * @block_tx: whether transmissions should be blocked while changing
+ * @count: number of beacons until switch
+ */
+struct cfg80211_csa_settings {
+	struct cfg80211_chan_def chandef;
+	struct cfg80211_beacon_data beacon_csa;
+	u16 counter_offset_beacon, counter_offset_presp;
+	struct cfg80211_beacon_data beacon_after;
+	bool radar_required;
+	bool block_tx;
+	u8 count;
+};
+
+/**
  * enum station_parameters_apply_mask - station parameter values to apply
  * @STATION_PARAM_APPLY_UAPSD: apply new uAPSD parameters (uapsd_queues, max_sp)
  * @STATION_PARAM_APPLY_CAPABILITY: apply new capability
@@ -764,7 +815,7 @@ int cfg80211_check_station_change(struct wiphy *wiphy,
  * @STATION_INFO_PLINK_STATE: @plink_state filled
  * @STATION_INFO_SIGNAL: @signal filled
  * @STATION_INFO_TX_BITRATE: @txrate fields are filled
- *  (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
+ *	(tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
  * @STATION_INFO_RX_PACKETS: @rx_packets filled with 32-bit value
  * @STATION_INFO_TX_PACKETS: @tx_packets filled with 32-bit value
  * @STATION_INFO_TX_RETRIES: @tx_retries filled
@@ -1285,6 +1336,7 @@ struct cfg80211_ssid {
  * @n_ssids: number of SSIDs
  * @channels: channels to scan on.
  * @n_channels: total number of channels to scan
+ * @scan_width: channel width for scanning
  * @ie: optional information element(s) to add into Probe Request or %NULL
  * @ie_len: length of ie in octets
  * @flags: bit field of flags controlling operation
@@ -1300,6 +1352,7 @@ struct cfg80211_scan_request {
 	struct cfg80211_ssid *ssids;
 	int n_ssids;
 	u32 n_channels;
+	enum nl80211_bss_scan_width scan_width;
 	const u8 *ie;
 	size_t ie_len;
 	u32 flags;
@@ -1333,6 +1386,7 @@ struct cfg80211_match_set {
  * @ssids: SSIDs to scan for (passed in the probe_reqs in active scans)
  * @n_ssids: number of SSIDs
  * @n_channels: total number of channels to scan
+ * @scan_width: channel width for scanning
  * @interval: interval between each scheduled scan cycle
  * @ie: optional information element(s) to add into Probe Request or %NULL
  * @ie_len: length of ie in octets
@@ -1352,6 +1406,7 @@ struct cfg80211_sched_scan_request {
 	struct cfg80211_ssid *ssids;
 	int n_ssids;
 	u32 n_channels;
+	enum nl80211_bss_scan_width scan_width;
 	u32 interval;
 	const u8 *ie;
 	size_t ie_len;
@@ -1403,6 +1458,7 @@ struct cfg80211_bss_ies {
  * for use in scan results and similar.
  *
  * @channel: channel this BSS is on
+ * @scan_width: width of the control channel
  * @bssid: BSSID of the BSS
  * @beacon_interval: the beacon interval as from the frame
  * @capability: the capability field in host byte order
@@ -1424,6 +1480,7 @@ struct cfg80211_bss_ies {
  */
 struct cfg80211_bss {
 	struct ieee80211_channel *channel;
+	enum nl80211_bss_scan_width scan_width;
 
 	const struct cfg80211_bss_ies __rcu *ies;
 	const struct cfg80211_bss_ies __rcu *beacon_ies;
@@ -1509,7 +1566,7 @@ enum cfg80211_assoc_req_flags {
  * @prev_bssid: previous BSSID, if not %NULL use reassociate frame
  * @flags:  See &enum cfg80211_assoc_req_flags
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  * @vht_capa: VHT capability override
  * @vht_capa_mask: VHT capability mask indicating which fields to use
@@ -1592,6 +1649,9 @@ struct cfg80211_disassoc_request {
  *	user space. Otherwise, port is marked authorized by default.
  * @basic_rates: bitmap of basic rates to use when creating the IBSS
  * @mcast_rate: per-band multicast rate index + 1 (0: disabled)
+ * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
+ *	will be used in ht_capa.  Un-supported values will be ignored.
+ * @ht_capa_mask:  The bits of ht_capa which are to be used.
  */
 struct cfg80211_ibss_params {
 	u8 *ssid;
@@ -1605,6 +1665,8 @@ struct cfg80211_ibss_params {
 	bool privacy;
 	bool control_port;
 	int mcast_rate[IEEE80211_NUM_BANDS];
+	struct ieee80211_ht_cap ht_capa;
+	struct ieee80211_ht_cap ht_capa_mask;
 };
 
 /**
@@ -1630,9 +1692,9 @@ struct cfg80211_ibss_params {
  * @key: WEP key for shared key authentication
  * @flags:  See &enum cfg80211_assoc_req_flags
  * @bg_scan_period:  Background scan period in seconds
- *   or -1 to indicate that default value is to be used.
+ *	or -1 to indicate that default value is to be used.
  * @ht_capa:  HT Capabilities over-rides.  Values set in ht_capa_mask
- *   will be used in ht_capa.  Un-supported values will be ignored.
+ *	will be used in ht_capa.  Un-supported values will be ignored.
  * @ht_capa_mask:  The bits of ht_capa which are to be used.
  * @vht_capa:  VHT Capability overrides
  * @vht_capa_mask: The bits of vht_capa which are to be used.
@@ -1698,7 +1760,7 @@ struct cfg80211_pmksa {
 };
 
 /**
- * struct cfg80211_wowlan_trig_pkt_pattern - packet pattern
+ * struct cfg80211_pkt_pattern - packet pattern
  * @mask: bitmask where to match pattern and where to ignore bytes,
  *	one bit per byte, in same format as nl80211
  * @pattern: bytes to match where bitmask is 1
@@ -1708,7 +1770,7 @@ struct cfg80211_pmksa {
  * Internal note: @mask and @pattern are allocated in one chunk of
  * memory, free @mask only!
  */
-struct cfg80211_wowlan_trig_pkt_pattern {
+struct cfg80211_pkt_pattern {
 	u8 *mask, *pattern;
 	int pattern_len;
 	int pkt_offset;
@@ -1770,12 +1832,41 @@ struct cfg80211_wowlan {
 	bool any, disconnect, magic_pkt, gtk_rekey_failure,
 	     eap_identity_req, four_way_handshake,
 	     rfkill_release;
-	struct cfg80211_wowlan_trig_pkt_pattern *patterns;
+	struct cfg80211_pkt_pattern *patterns;
 	struct cfg80211_wowlan_tcp *tcp;
 	int n_patterns;
 };
 
 /**
+ * struct cfg80211_coalesce_rules - Coalesce rule parameters
+ *
+ * This structure defines coalesce rule for the device.
+ * @delay: maximum coalescing delay in msecs.
+ * @condition: condition for packet coalescence.
+ *	see &enum nl80211_coalesce_condition.
+ * @patterns: array of packet patterns
+ * @n_patterns: number of patterns
+ */
+struct cfg80211_coalesce_rules {
+	int delay;
+	enum nl80211_coalesce_condition condition;
+	struct cfg80211_pkt_pattern *patterns;
+	int n_patterns;
+};
+
+/**
+ * struct cfg80211_coalesce - Packet coalescing settings
+ *
+ * This structure defines coalescing settings.
+ * @rules: array of coalesce rules
+ * @n_rules: number of rules
+ */
+struct cfg80211_coalesce {
+	struct cfg80211_coalesce_rules *rules;
+	int n_rules;
+};
+
+/**
  * struct cfg80211_wowlan_wakeup - wakeup report
  * @disconnect: woke up by getting disconnected
  * @magic_pkt: woke up by receiving magic packet
@@ -2071,6 +2162,9 @@ struct cfg80211_update_ft_ies_params {
  *	driver can take the most appropriate actions.
  * @crit_proto_stop: Indicates critical protocol no longer needs increased link
  *	reliability. This operation can not fail.
+ * @set_coalesce: Set coalesce parameters.
+ *
+ * @channel_switch: initiate channel-switch procedure (with CSA)
  */
 struct cfg80211_ops {
 	int	(*suspend)(struct wiphy *wiphy, struct cfg80211_wowlan *wow);
@@ -2306,6 +2400,12 @@ struct cfg80211_ops {
 				    u16 duration);
 	void	(*crit_proto_stop)(struct wiphy *wiphy,
 				   struct wireless_dev *wdev);
+	int	(*set_coalesce)(struct wiphy *wiphy,
+				struct cfg80211_coalesce *coalesce);
+
+	int	(*channel_switch)(struct wiphy *wiphy,
+				  struct net_device *dev,
+				  struct cfg80211_csa_settings *params);
 };
 
 /*
@@ -2371,6 +2471,8 @@ struct cfg80211_ops {
  * @WIPHY_FLAG_OFFCHAN_TX: Device supports direct off-channel TX.
  * @WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL: Device supports remain-on-channel call.
  * @WIPHY_FLAG_SUPPORTS_5_10_MHZ: Device supports 5 MHz and 10 MHz channels.
+ * @WIPHY_FLAG_HAS_CHANNEL_SWITCH: Device supports channel switch in
+ *	beaconing mode (AP, IBSS, Mesh, ...).
  */
 enum wiphy_flags {
 	WIPHY_FLAG_CUSTOM_REGULATORY		= BIT(0),
@@ -2395,6 +2497,7 @@ enum wiphy_flags {
 	WIPHY_FLAG_OFFCHAN_TX			= BIT(20),
 	WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL	= BIT(21),
 	WIPHY_FLAG_SUPPORTS_5_10_MHZ		= BIT(22),
+	WIPHY_FLAG_HAS_CHANNEL_SWITCH		= BIT(23),
 };
 
 /**
@@ -2532,6 +2635,25 @@ struct wiphy_wowlan_support {
 };
 
 /**
+ * struct wiphy_coalesce_support - coalesce support data
+ * @n_rules: maximum number of coalesce rules
+ * @max_delay: maximum supported coalescing delay in msecs
+ * @n_patterns: number of supported patterns in a rule
+ *	(see nl80211.h for the pattern definition)
+ * @pattern_max_len: maximum length of each pattern
+ * @pattern_min_len: minimum length of each pattern
+ * @max_pkt_offset: maximum Rx packet offset
+ */
+struct wiphy_coalesce_support {
+	int n_rules;
+	int max_delay;
+	int n_patterns;
+	int pattern_max_len;
+	int pattern_min_len;
+	int max_pkt_offset;
+};
+
+/**
  * struct wiphy - wireless hardware description
  * @reg_notifier: the driver's regulatory notification callback,
  *	note that if your driver uses wiphy_apply_custom_regulatory()
@@ -2641,6 +2763,7 @@ struct wiphy_wowlan_support {
  *	802.11-2012 8.4.2.29 for the defined fields.
  * @extended_capabilities_mask: mask of the valid values
  * @extended_capabilities_len: length of the extended capabilities
+ * @coalesce: packet coalescing support information
  */
 struct wiphy {
 	/* assign these fields before you register the wiphy */
@@ -2750,6 +2873,8 @@ struct wiphy {
 	const struct iw_handler_def *wext;
 #endif
 
+	const struct wiphy_coalesce_support *coalesce;
+
 	char priv[0] __aligned(NETDEV_ALIGN);
 };
 
@@ -3063,11 +3188,13 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
 /**
  * ieee80211_mandatory_rates - get mandatory rates for a given band
  * @sband: the band to look for rates in
+ * @scan_width: width of the control channel
  *
  * This function returns a bitmap of the mandatory rates for the given
  * band, bits are set according to the rate position in the bitrates array.
  */
-u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband);
+u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
+			      enum nl80211_bss_scan_width scan_width);
 
 /*
  * Radiotap parsing functions -- for controlled injection support
@@ -3379,10 +3506,11 @@ void cfg80211_sched_scan_results(struct wiphy *wiphy);
 void cfg80211_sched_scan_stopped(struct wiphy *wiphy);
 
 /**
- * cfg80211_inform_bss_frame - inform cfg80211 of a received BSS frame
+ * cfg80211_inform_bss_width_frame - inform cfg80211 of a received BSS frame
  *
  * @wiphy: the wiphy reporting the BSS
  * @channel: The channel the frame was received on
+ * @scan_width: width of the control channel
  * @mgmt: the management frame (probe response or beacon)
  * @len: length of the management frame
  * @signal: the signal strength, type depends on the wiphy's signal_type
@@ -3395,16 +3523,29 @@ void cfg80211_sched_scan_stopped(struct wiphy *wiphy);
  * Or %NULL on error.
  */
 struct cfg80211_bss * __must_check
+cfg80211_inform_bss_width_frame(struct wiphy *wiphy,
+				struct ieee80211_channel *channel,
+				enum nl80211_bss_scan_width scan_width,
+				struct ieee80211_mgmt *mgmt, size_t len,
+				s32 signal, gfp_t gfp);
+
+static inline struct cfg80211_bss * __must_check
 cfg80211_inform_bss_frame(struct wiphy *wiphy,
 			  struct ieee80211_channel *channel,
 			  struct ieee80211_mgmt *mgmt, size_t len,
-			  s32 signal, gfp_t gfp);
+			  s32 signal, gfp_t gfp)
+{
+	return cfg80211_inform_bss_width_frame(wiphy, channel,
+					       NL80211_BSS_CHAN_WIDTH_20,
+					       mgmt, len, signal, gfp);
+}
 
 /**
  * cfg80211_inform_bss - inform cfg80211 of a new BSS
  *
  * @wiphy: the wiphy reporting the BSS
  * @channel: The channel the frame was received on
+ * @scan_width: width of the control channel
  * @bssid: the BSSID of the BSS
  * @tsf: the TSF sent by the peer in the beacon/probe response (or 0)
  * @capability: the capability field sent by the peer
@@ -3421,11 +3562,26 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy,
  * Or %NULL on error.
  */
 struct cfg80211_bss * __must_check
+cfg80211_inform_bss_width(struct wiphy *wiphy,
+			  struct ieee80211_channel *channel,
+			  enum nl80211_bss_scan_width scan_width,
+			  const u8 *bssid, u64 tsf, u16 capability,
+			  u16 beacon_interval, const u8 *ie, size_t ielen,
+			  s32 signal, gfp_t gfp);
+
+static inline struct cfg80211_bss * __must_check
 cfg80211_inform_bss(struct wiphy *wiphy,
 		    struct ieee80211_channel *channel,
 		    const u8 *bssid, u64 tsf, u16 capability,
 		    u16 beacon_interval, const u8 *ie, size_t ielen,
-		    s32 signal, gfp_t gfp);
+		    s32 signal, gfp_t gfp)
+{
+	return cfg80211_inform_bss_width(wiphy, channel,
+					 NL80211_BSS_CHAN_WIDTH_20,
+					 bssid, tsf, capability,
+					 beacon_interval, ie, ielen, signal,
+					 gfp);
+}
 
 struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
 				      struct ieee80211_channel *channel,
@@ -3471,6 +3627,19 @@ void cfg80211_put_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
  */
 void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
 
+static inline enum nl80211_bss_scan_width
+cfg80211_chandef_to_scan_width(const struct cfg80211_chan_def *chandef)
+{
+	switch (chandef->width) {
+	case NL80211_CHAN_WIDTH_5:
+		return NL80211_BSS_CHAN_WIDTH_5;
+	case NL80211_CHAN_WIDTH_10:
+		return NL80211_BSS_CHAN_WIDTH_10;
+	default:
+		return NL80211_BSS_CHAN_WIDTH_20;
+	}
+}
+
 /**
  * cfg80211_rx_mlme_mgmt - notification of processed MLME management frame
  * @dev: network device
diff --git a/include/net/ieee80211_radiotap.h b/include/net/ieee80211_radiotap.h
index c6d07cb074bc..8b5b71433297 100644
--- a/include/net/ieee80211_radiotap.h
+++ b/include/net/ieee80211_radiotap.h
@@ -230,6 +230,10 @@ enum ieee80211_radiotap_type {
 #define	IEEE80211_CHAN_PASSIVE	0x0200	/* Only passive scan allowed */
 #define	IEEE80211_CHAN_DYN	0x0400	/* Dynamic CCK-OFDM channel */
 #define	IEEE80211_CHAN_GFSK	0x0800	/* GFSK channel (FHSS PHY) */
+#define	IEEE80211_CHAN_GSM	0x1000	/* GSM (900 MHz) */
+#define	IEEE80211_CHAN_STURBO	0x2000	/* Static Turbo */
+#define	IEEE80211_CHAN_HALF	0x4000	/* Half channel (10 MHz wide) */
+#define	IEEE80211_CHAN_QUARTER	0x8000	/* Quarter channel (5 MHz wide) */
 
 /* For IEEE80211_RADIOTAP_FLAGS */
 #define	IEEE80211_RADIOTAP_F_CFP	0x01	/* sent/received
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index e5f02909f1ad..ab94dbc331a0 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -152,11 +152,14 @@ struct ieee80211_low_level_stats {
  * @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
  * @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
  * @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
+ * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
+ *	this is used only with channel switching with CSA
  */
 enum ieee80211_chanctx_change {
 	IEEE80211_CHANCTX_CHANGE_WIDTH		= BIT(0),
 	IEEE80211_CHANCTX_CHANGE_RX_CHAINS	= BIT(1),
 	IEEE80211_CHANCTX_CHANGE_RADAR		= BIT(2),
+	IEEE80211_CHANCTX_CHANGE_CHANNEL	= BIT(3),
 };
 
 /**
@@ -811,6 +814,8 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
  * @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
  *	is stored in the @ampdu_delimiter_crc field)
  * @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
+ * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
+ * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
  */
 enum mac80211_rx_flags {
 	RX_FLAG_MMIC_ERROR		= BIT(0),
@@ -839,6 +844,8 @@ enum mac80211_rx_flags {
 	RX_FLAG_80P80MHZ		= BIT(24),
 	RX_FLAG_160MHZ			= BIT(25),
 	RX_FLAG_STBC_MASK		= BIT(26) | BIT(27),
+	RX_FLAG_10MHZ			= BIT(28),
+	RX_FLAG_5MHZ			= BIT(29),
 };
 
 #define RX_FLAG_STBC_SHIFT		26
@@ -1004,11 +1011,11 @@ enum ieee80211_smps_mode {
  * @radar_enabled: whether radar detection is enabled
  *
  * @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
- *    (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
- *    but actually means the number of transmissions not the number of retries
+ *	(a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ *	but actually means the number of transmissions not the number of retries
  * @short_frame_max_tx_count: Maximum number of transmissions for a "short"
- *    frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
- *    number of transmissions not the number of retries
+ *	frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ *	number of transmissions not the number of retries
  *
  * @smps_mode: spatial multiplexing powersave mode; note that
  *	%IEEE80211_SMPS_STATIC is used when the device is not
@@ -1080,6 +1087,7 @@ enum ieee80211_vif_flags {
  * @addr: address of this interface
  * @p2p: indicates whether this AP or STA interface is a p2p
  *	interface, i.e. a GO or p2p-sta respectively
+ * @csa_active: marks whether a channel switch is going on
  * @driver_flags: flags/capabilities the driver has for this interface,
  *	these need to be set (or cleared) when the interface is added
  *	or, if supported by the driver, the interface type is changed
@@ -1092,7 +1100,7 @@ enum ieee80211_vif_flags {
  *	be off when it is %NULL there can still be races and packets could be
  *	processed after it switches back to %NULL.
  * @debugfs_dir: debugfs dentry, can be used by drivers to create own per
- *      interface debug files. Note that it will be NULL for the virtual
+ *	interface debug files. Note that it will be NULL for the virtual
  *	monitor interface (if that is requested.)
  * @drv_priv: data area for driver use, will always be aligned to
  *	sizeof(void *).
@@ -1102,6 +1110,7 @@ struct ieee80211_vif {
 	struct ieee80211_bss_conf bss_conf;
 	u8 addr[ETH_ALEN];
 	bool p2p;
+	bool csa_active;
 
 	u8 cab_queue;
 	u8 hw_queue[IEEE80211_NUM_ACS];
@@ -1425,10 +1434,10 @@ struct ieee80211_tx_control {
  *	the stack.
  *
  * @IEEE80211_HW_CONNECTION_MONITOR:
- *      The hardware performs its own connection monitoring, including
- *      periodic keep-alives to the AP and probing the AP on beacon loss.
- *      When this flag is set, signaling beacon-loss will cause an immediate
- *      change to disassociated state.
+ *	The hardware performs its own connection monitoring, including
+ *	periodic keep-alives to the AP and probing the AP on beacon loss.
+ *	When this flag is set, signaling beacon-loss will cause an immediate
+ *	change to disassociated state.
  *
  * @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
  *	This device needs to get data from beacon before association (i.e.
@@ -1526,10 +1535,10 @@ enum ieee80211_hw_flags {
  * @channel_change_time: time (in microseconds) it takes to change channels.
  *
  * @max_signal: Maximum value for signal (rssi) in RX information, used
- *     only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ *	only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
  *
  * @max_listen_interval: max listen interval in units of beacon interval
- *     that HW supports
+ *	that HW supports
  *
  * @queues: number of available hardware transmit queues for
  *	data packets. WMM/QoS requires at least four, these
@@ -2443,7 +2452,7 @@ enum ieee80211_roc_type {
  *	The callback can sleep.
  *
  * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
- *      Currently, this is only used for IBSS mode debugging. Is not a
+ *	Currently, this is only used for IBSS mode debugging. Is not a
  *	required function.
  *	The callback can sleep.
  *
@@ -2633,6 +2642,16 @@ enum ieee80211_roc_type {
  * @ipv6_addr_change: IPv6 address assignment on the given interface changed.
  *	Currently, this is only called for managed or P2P client interfaces.
  *	This callback is optional; it must not sleep.
+ *
+ * @channel_switch_beacon: Starts a channel switch to a new channel.
+ *	Beacons are modified to include CSA or ECSA IEs before calling this
+ *	function. The corresponding count fields in these IEs must be
+ *	decremented, and when they reach zero the driver must call
+ *	ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
+ *	get the csa counter decremented by mac80211, but must check if it is
+ *	zero using ieee80211_csa_is_complete() after the beacon has been
+ *	transmitted and then call ieee80211_csa_finish().
+ *
  */
 struct ieee80211_ops {
 	void (*tx)(struct ieee80211_hw *hw,
@@ -2820,6 +2839,9 @@ struct ieee80211_ops {
 				 struct ieee80211_vif *vif,
 				 struct inet6_dev *idev);
 #endif
+	void (*channel_switch_beacon)(struct ieee80211_hw *hw,
+				      struct ieee80211_vif *vif,
+				      struct cfg80211_chan_def *chandef);
 };
 
 /**
@@ -3315,6 +3337,25 @@ static inline struct sk_buff *ieee80211_beacon_get(struct ieee80211_hw *hw,
 }
 
 /**
+ * ieee80211_csa_finish - notify mac80211 about channel switch
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * After a channel switch announcement was scheduled and the counter in this
+ * announcement hit zero, this function must be called by the driver to
+ * notify mac80211 that the channel can be changed.
+ */
+void ieee80211_csa_finish(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_csa_is_complete - find out if counters reached zero
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * This function returns whether the channel switch counters reached zero.
+ */
+bool ieee80211_csa_is_complete(struct ieee80211_vif *vif);
+
+
+/**
  * ieee80211_proberesp_get - retrieve a Probe Response template
  * @hw: pointer obtained from ieee80211_alloc_hw().
  * @vif: &struct ieee80211_vif pointer from the add_interface callback.
@@ -4204,8 +4245,10 @@ struct rate_control_ops {
 
 	void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
 	void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
+			  struct cfg80211_chan_def *chandef,
 			  struct ieee80211_sta *sta, void *priv_sta);
 	void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
+			    struct cfg80211_chan_def *chandef,
 			    struct ieee80211_sta *sta, void *priv_sta,
 			    u32 changed);
 	void (*free_sta)(void *priv, struct ieee80211_sta *sta,
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 861e5eba3953..1f42bc3dcb9c 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -126,6 +126,31 @@
  */
 
 /**
+ * DOC: packet coalesce support
+ *
+ * In most cases, host that receives IPv4 and IPv6 multicast/broadcast
+ * packets does not do anything with these packets. Therefore the
+ * reception of these unwanted packets causes unnecessary processing
+ * and power consumption.
+ *
+ * Packet coalesce feature helps to reduce number of received interrupts
+ * to host by buffering these packets in firmware/hardware for some
+ * predefined time. Received interrupt will be generated when one of the
+ * following events occur.
+ * a) Expiration of hardware timer whose expiration time is set to maximum
+ * coalescing delay of matching coalesce rule.
+ * b) Coalescing buffer in hardware reaches it's limit.
+ * c) Packet doesn't match any of the configured coalesce rules.
+ *
+ * User needs to configure following parameters for creating a coalesce
+ * rule.
+ * a) Maximum coalescing delay
+ * b) List of packet patterns which needs to be matched
+ * c) Condition for coalescence. pattern 'match' or 'no match'
+ * Multiple such rules can be created.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -648,6 +673,19 @@
  * @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can
  *	return back to normal.
  *
+ * @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules.
+ * @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
+ *
+ * @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
+ *	the new channel information (Channel Switch Announcement - CSA)
+ *	in the beacon for some time (as defined in the
+ *	%NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
+ *	new channel. Userspace provides the new channel information (using
+ *	%NL80211_ATTR_WIPHY_FREQ and the attributes determining channel
+ *	width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform
+ *	other station that transmission must be blocked until the channel
+ *	switch is complete.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -810,6 +848,11 @@ enum nl80211_commands {
 	NL80211_CMD_CRIT_PROTOCOL_START,
 	NL80211_CMD_CRIT_PROTOCOL_STOP,
 
+	NL80211_CMD_GET_COALESCE,
+	NL80211_CMD_SET_COALESCE,
+
+	NL80211_CMD_CHANNEL_SWITCH,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1436,6 +1479,20 @@ enum nl80211_commands {
  *	allowed to be used with the first @NL80211_CMD_SET_STATION command to
  *	update a TDLS peer STA entry.
  *
+ * @NL80211_ATTR_COALESCE_RULE: Coalesce rule information.
+ *
+ * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's
+ *	until the channel switch event.
+ * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
+ *	must be blocked on the current channel (before the channel switch
+ *	operation).
+ * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
+ *	for the time while performing a channel switch.
+ * @NL80211_ATTR_CSA_C_OFF_BEACON: Offset of the channel switch counter
+ *	field in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
+ * @NL80211_ATTR_CSA_C_OFF_PRESP: Offset of the channel switch counter
+ *	field in the probe response (%NL80211_ATTR_PROBE_RESP).
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1736,6 +1793,14 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_PEER_AID,
 
+	NL80211_ATTR_COALESCE_RULE,
+
+	NL80211_ATTR_CH_SWITCH_COUNT,
+	NL80211_ATTR_CH_SWITCH_BLOCK_TX,
+	NL80211_ATTR_CSA_IES,
+	NL80211_ATTR_CSA_C_OFF_BEACON,
+	NL80211_ATTR_CSA_C_OFF_PRESP,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -2773,6 +2838,21 @@ enum nl80211_chan_width {
 };
 
 /**
+ * enum nl80211_bss_scan_width - control channel width for a BSS
+ *
+ * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
+ *
+ * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
+ * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
+ * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
+ */
+enum nl80211_bss_scan_width {
+	NL80211_BSS_CHAN_WIDTH_20,
+	NL80211_BSS_CHAN_WIDTH_10,
+	NL80211_BSS_CHAN_WIDTH_5,
+};
+
+/**
  * enum nl80211_bss - netlink attributes for a BSS
  *
  * @__NL80211_BSS_INVALID: invalid
@@ -2796,6 +2876,8 @@ enum nl80211_chan_width {
  * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
  *	elements from a Beacon frame (bin); not present if no Beacon frame has
  *	yet been received
+ * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
+ *	(u32, enum nl80211_bss_scan_width)
  * @__NL80211_BSS_AFTER_LAST: internal
  * @NL80211_BSS_MAX: highest BSS attribute
  */
@@ -2812,6 +2894,7 @@ enum nl80211_bss {
 	NL80211_BSS_STATUS,
 	NL80211_BSS_SEEN_MS_AGO,
 	NL80211_BSS_BEACON_IES,
+	NL80211_BSS_CHAN_WIDTH,
 
 	/* keep last */
 	__NL80211_BSS_AFTER_LAST,
@@ -3060,11 +3143,11 @@ enum nl80211_tx_power_setting {
 };
 
 /**
- * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
- * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
- * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ * enum nl80211_packet_pattern_attr - packet pattern attribute
+ * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
  *	a zero bit are ignored
- * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
  *	a bit for each byte in the pattern. The lowest-order bit corresponds
  *	to the first byte of the pattern, but the bytes of the pattern are
  *	in a little-endian-like format, i.e. the 9th byte of the pattern
@@ -3075,39 +3158,50 @@ enum nl80211_tx_power_setting {
  *	Note that the pattern matching is done as though frames were not
  *	802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
  *	first (including SNAP header unpacking) and then matched.
- * @NL80211_WOWLAN_PKTPAT_OFFSET: packet offset, pattern is matched after
+ * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
  *	these fixed number of bytes of received packet
- * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
- * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ * @NUM_NL80211_PKTPAT: number of attributes
+ * @MAX_NL80211_PKTPAT: max attribute number
  */
-enum nl80211_wowlan_packet_pattern_attr {
-	__NL80211_WOWLAN_PKTPAT_INVALID,
-	NL80211_WOWLAN_PKTPAT_MASK,
-	NL80211_WOWLAN_PKTPAT_PATTERN,
-	NL80211_WOWLAN_PKTPAT_OFFSET,
+enum nl80211_packet_pattern_attr {
+	__NL80211_PKTPAT_INVALID,
+	NL80211_PKTPAT_MASK,
+	NL80211_PKTPAT_PATTERN,
+	NL80211_PKTPAT_OFFSET,
 
-	NUM_NL80211_WOWLAN_PKTPAT,
-	MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+	NUM_NL80211_PKTPAT,
+	MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
 };
 
 /**
- * struct nl80211_wowlan_pattern_support - pattern support information
+ * struct nl80211_pattern_support - packet pattern support information
  * @max_patterns: maximum number of patterns supported
  * @min_pattern_len: minimum length of each pattern
  * @max_pattern_len: maximum length of each pattern
  * @max_pkt_offset: maximum Rx packet offset
  *
  * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
- * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
- * capability information given by the kernel to userspace.
+ * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in
+ * %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of
+ * %NL80211_ATTR_COALESCE_RULE in the capability information given
+ * by the kernel to userspace.
  */
-struct nl80211_wowlan_pattern_support {
+struct nl80211_pattern_support {
 	__u32 max_patterns;
 	__u32 min_pattern_len;
 	__u32 max_pattern_len;
 	__u32 max_pkt_offset;
 } __attribute__((packed));
 
+/* only for backward compatibility */
+#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
+#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
+#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
+#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
+#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
+#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
+#define nl80211_wowlan_pattern_support nl80211_pattern_support
+
 /**
  * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
  * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
@@ -3127,7 +3221,7 @@ struct nl80211_wowlan_pattern_support {
  *	pattern matching is done after the packet is converted to the MSDU.
  *
  *	In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
- *	carrying a &struct nl80211_wowlan_pattern_support.
+ *	carrying a &struct nl80211_pattern_support.
  *
  *	When reporting wakeup. it is a u32 attribute containing the 0-based
  *	index of the pattern that caused the wakeup, in the patterns passed
@@ -3284,7 +3378,7 @@ struct nl80211_wowlan_tcp_data_token_feature {
  * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
  *	u32 attribute holding the maximum length
  * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
- *	feature advertising. The mask works like @NL80211_WOWLAN_PKTPAT_MASK
+ *	feature advertising. The mask works like @NL80211_PKTPAT_MASK
  *	but on the TCP payload only.
  * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
  * @MAX_NL80211_WOWLAN_TCP: highest attribute number
@@ -3309,6 +3403,55 @@ enum nl80211_wowlan_tcp_attrs {
 };
 
 /**
+ * struct nl80211_coalesce_rule_support - coalesce rule support information
+ * @max_rules: maximum number of rules supported
+ * @pat: packet pattern support information
+ * @max_delay: maximum supported coalescing delay in msecs
+ *
+ * This struct is carried in %NL80211_ATTR_COALESCE_RULE in the
+ * capability information given by the kernel to userspace.
+ */
+struct nl80211_coalesce_rule_support {
+	__u32 max_rules;
+	struct nl80211_pattern_support pat;
+	__u32 max_delay;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_attr_coalesce_rule - coalesce rule attribute
+ * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute
+ * @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing
+ * @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence,
+ *	see &enum nl80211_coalesce_condition.
+ * @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched
+ *	after these fixed number of bytes of received packet
+ * @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes
+ * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number
+ */
+enum nl80211_attr_coalesce_rule {
+	__NL80211_COALESCE_RULE_INVALID,
+	NL80211_ATTR_COALESCE_RULE_DELAY,
+	NL80211_ATTR_COALESCE_RULE_CONDITION,
+	NL80211_ATTR_COALESCE_RULE_PKT_PATTERN,
+
+	/* keep last */
+	NUM_NL80211_ATTR_COALESCE_RULE,
+	NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1
+};
+
+/**
+ * enum nl80211_coalesce_condition - coalesce rule conditions
+ * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
+ *	in a rule are matched.
+ * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
+ *	in a rule are not matched.
+ */
+enum nl80211_coalesce_condition {
+	NL80211_COALESCE_CONDITION_MATCH,
+	NL80211_COALESCE_CONDITION_NO_MATCH
+};
+
+/**
  * enum nl80211_iface_limit_attrs - limit attributes
  * @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
  * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that