diff options
52 files changed, 1781 insertions, 1722 deletions
diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 8e2e0ba2f486..a591c6741d75 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -21,6 +21,12 @@ Optional properties: - cd-inverted: when present, polarity on the cd gpio line is inverted - wp-inverted: when present, polarity on the wp gpio line is inverted - max-frequency: maximum operating clock frequency +- no-1-8-v: when present, denotes that 1.8v card voltage is not supported on + this system, even if the controller claims it is. + +Optional SDIO properties: +- keep-power-in-suspend: Preserves card power during a suspend/resume cycle +- enable-sdio-wakeup: Enables wake up of host system on SDIO IRQ assertion Example: @@ -33,4 +39,6 @@ sdhci@ab000000 { cd-inverted; wp-gpios = <&gpio 70 0>; max-frequency = <50000000>; + keep-power-in-suspend; + enable-sdio-wakeup; } diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 630a7d7f4718..97e9e315400d 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below. [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the "Optional Board Specific Properties" section below. -[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property - is not specified, it is assumed that there is no card detection - mechanism used. - Required SoC Specific Properties: - compatible: should be one of the following - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci @@ -24,14 +20,18 @@ Required SoC Specific Properties: controller. Required Board Specific Properties: -- gpios: Should specify the gpios used for clock, command and data lines. The - gpio specifier format depends on the gpio controller. +- Samsung GPIO variant (will be completely replaced by pinctrl): + - gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. +- Pinctrl variant (preferred if available): + - pinctrl-0: Should specify pin control groups used for this controller. + - pinctrl-names: Should contain only one value - "default". Optional Board Specific Properties: - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed through a pinmux to the card-detect pin of the card slot. This property should be used only if none of the mmc core card-detect properties are - used. + used. Only for Samsung GPIO variant. Example: sdhci@12530000 { @@ -40,12 +40,18 @@ Example: interrupts = <0 75 0>; bus-width = <4>; cd-gpios = <&gpk2 2 2 3 3>; + + /* Samsung GPIO variant */ gpios = <&gpk2 0 2 0 3>, /* clock line */ <&gpk2 1 2 0 3>, /* command line */ <&gpk2 3 2 3 3>, /* data line 0 */ <&gpk2 4 2 3 3>, /* data line 1 */ <&gpk2 5 2 3 3>, /* data line 2 */ <&gpk2 6 2 3 3>; /* data line 3 */ + + /* Pinctrl variant */ + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; + pinctrl-names = "default"; }; Note: This example shows both SoC specific and board specific properties diff --git a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 06cd32d08052..06cd32d08052 100644 --- a/Documentation/devicetree/bindings/mmc/synposis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt index be76a23b34c4..ed271fc255b2 100644 --- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt +++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt @@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards "supply-name" examples are "vmmc", "vmmc_aux" etc ti,non-removable: non-removable slot (like eMMC) ti,needs-special-reset: Requires a special softreset sequence +ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed Example: mmc1: mmc@0x4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt new file mode 100644 index 000000000000..d7fb6abb3eb8 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/vt8500-sdmmc.txt @@ -0,0 +1,23 @@ +* Wondermedia WM8505/WM8650 SD/MMC Host Controller + +This file documents differences between the core properties described +by mmc.txt and the properties used by the wmt-sdmmc driver. + +Required properties: +- compatible: Should be "wm,wm8505-sdhc". +- interrupts: Two interrupts are required - regular irq and dma irq. + +Optional properties: +- sdon-inverted: SD_ON bit is inverted on the controller + +Examples: + +sdhc@d800a000 { + compatible = "wm,wm8505-sdhc"; + reg = <0xd800a000 0x1000>; + interrupts = <20 21>; + clocks = <&sdhc>; + bus-width = <4>; + sdon-inverted; +}; + diff --git a/Documentation/mmc/mmc-dev-attrs.txt b/Documentation/mmc/mmc-dev-attrs.txt index 22ae8441489f..0d98fac8893b 100644 --- a/Documentation/mmc/mmc-dev-attrs.txt +++ b/Documentation/mmc/mmc-dev-attrs.txt @@ -25,6 +25,8 @@ All attributes are read-only. serial Product Serial Number (from CID Register) erase_size Erase group size preferred_erase_size Preferred erase size + raw_rpmb_size_mult RPMB partition size + rel_sectors Reliable write sector count Note on Erase Size and Preferred Erase Size: @@ -65,6 +67,11 @@ Note on Erase Size and Preferred Erase Size: "preferred_erase_size" is in bytes. +Note on raw_rpmb_size_mult: + "raw_rpmb_size_mult" is a mutliple of 128kB block. + RPMB size in byte is calculated by using the following equation: + RPMB partition size = 128kB x raw_rpmb_size_mult + SD/MMC/SDIO Clock Gating Attribute ================================== diff --git a/MAINTAINERS b/MAINTAINERS index 9386a63ea8f6..3d3abbacc1a3 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1237,6 +1237,7 @@ F: drivers/video/wm8505fb* F: drivers/video/wmt_ge_rops.* F: drivers/tty/serial/vt8500_serial.c F: drivers/rtc/rtc-vt8500-c +F: drivers/mmc/host/wmt-sdmmc.c ARM/ZIPIT Z2 SUPPORT M: Marek Vasut <marek.vasut@gmail.com> @@ -1368,14 +1369,6 @@ S: Maintained F: drivers/atm/ F: include/linux/atm* -ATMEL AT91 MCI DRIVER -M: Ludovic Desroches <ludovic.desroches@atmel.com> -L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) -W: http://www.atmel.com/products/AT91/ -W: http://www.at91.com/ -S: Maintained -F: drivers/mmc/host/at91_mci.c - ATMEL AT91 / AT32 MCI DRIVER M: Ludovic Desroches <ludovic.desroches@atmel.com> S: Maintained diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h index c55a4364ffb4..a0d92a960f46 100644 --- a/arch/arm/mach-at91/include/mach/board.h +++ b/arch/arm/mach-at91/include/mach/board.h @@ -70,16 +70,6 @@ struct at91_cf_data { extern void __init at91_add_device_cf(struct at91_cf_data *data); /* MMC / SD */ - /* at91_mci platform config */ -struct at91_mmc_data { - int det_pin; /* card detect IRQ */ - unsigned slot_b:1; /* uses Slot B */ - unsigned wire4:1; /* (SD) supports DAT0..DAT3 */ - int wp_pin; /* (SD) writeprotect detect */ - int vcc_pin; /* power switching (high == on) */ -}; -extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data); - /* atmel-mci platform config */ extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data); diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h index 8b4e4f2da2f5..346af5b490be 100644 --- a/arch/arm/plat-omap/include/plat/mmc.h +++ b/arch/arm/plat-omap/include/plat/mmc.h @@ -126,6 +126,7 @@ struct omap_mmc_platform_data { /* we can put the features above into this variable */ #define HSMMC_HAS_PBIAS (1 << 0) #define HSMMC_HAS_UPDATED_RESET (1 << 1) +#define HSMMC_HAS_HSPE_SUPPORT (1 << 2) unsigned features; int switch_pin; /* gpio (card detect) */ diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c index 172a768036d8..21056b9ef0a0 100644 --- a/drivers/mmc/card/block.c +++ b/drivers/mmc/card/block.c @@ -57,6 +57,7 @@ MODULE_ALIAS("mmc:block"); #define INAND_CMD38_ARG_SECERASE 0x80 #define INAND_CMD38_ARG_SECTRIM1 0x81 #define INAND_CMD38_ARG_SECTRIM2 0x88 +#define MMC_BLK_TIMEOUT_MS (10 * 60 * 1000) /* 10 minute timeout */ static DEFINE_MUTEX(block_mutex); @@ -126,6 +127,10 @@ enum mmc_blk_status { module_param(perdev_minors, int, 0444); MODULE_PARM_DESC(perdev_minors, "Minors numbers to allocate per device"); +static inline int mmc_blk_part_switch(struct mmc_card *card, + struct mmc_blk_data *md); +static int get_card_status(struct mmc_card *card, u32 *status, int retries); + static struct mmc_blk_data *mmc_blk_get(struct gendisk *disk) { struct mmc_blk_data *md; @@ -357,6 +362,38 @@ out: return ERR_PTR(err); } +static int ioctl_rpmb_card_status_poll(struct mmc_card *card, u32 *status, + u32 retries_max) +{ + int err; + u32 retry_count = 0; + + if (!status || !retries_max) + return -EINVAL; + + do { + err = get_card_status(card, status, 5); + if (err) + break; + + if (!R1_STATUS(*status) && + (R1_CURRENT_STATE(*status) != R1_STATE_PRG)) + break; /* RPMB programming operation complete */ + + /* + * Rechedule to give the MMC device a chance to continue + * processing the previous command without being polled too + * frequently. + */ + usleep_range(1000, 5000); + } while (++retry_count < retries_max); + + if (retry_count == retries_max) + err = -EPERM; + + return err; +} + static int mmc_blk_ioctl_cmd(struct block_device *bdev, struct mmc_ioc_cmd __user *ic_ptr) { @@ -368,6 +405,8 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, struct mmc_request mrq = {NULL}; struct scatterlist sg; int err; + int is_rpmb = false; + u32 status = 0; /* * The caller must have CAP_SYS_RAWIO, and must be calling this on the @@ -387,6 +426,9 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, goto cmd_err; } + if (md->area_type & MMC_BLK_DATA_AREA_RPMB) + is_rpmb = true; + card = md->queue.card; if (IS_ERR(card)) { err = PTR_ERR(card); @@ -437,12 +479,23 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, mmc_claim_host(card->host); + err = mmc_blk_part_switch(card, md); + if (err) + goto cmd_rel_host; + if (idata->ic.is_acmd) { err = mmc_app_cmd(card->host, card); if (err) goto cmd_rel_host; } + if (is_rpmb) { + err = mmc_set_blockcount(card, data.blocks, + idata->ic.write_flag & (1 << 31)); + if (err) + goto cmd_rel_host; + } + mmc_wait_for_req(card->host, &mrq); if (cmd.error) { @@ -478,6 +531,18 @@ static int mmc_blk_ioctl_cmd(struct block_device *bdev, } } + if (is_rpmb) { + /* + * Ensure RPMB command has completed by polling CMD13 + * "Send Status". + */ + err = ioctl_rpmb_card_status_poll(card, &status, 5); + if (err) + dev_err(mmc_dev(card->host), + "%s: Card Status=0x%08X, error %d\n", + __func__, status, err); + } + cmd_rel_host: mmc_release_host(card->host); @@ -1034,6 +1099,9 @@ static int mmc_blk_err_check(struct mmc_card *card, */ if (!mmc_host_is_spi(card->host) && rq_data_dir(req) != READ) { u32 status; + unsigned long timeout; + + timeout = jiffies + msecs_to_jiffies(MMC_BLK_TIMEOUT_MS); do { int err = get_card_status(card, &status, 5); if (err) { @@ -1041,6 +1109,17 @@ static int mmc_blk_err_check(struct mmc_card *card, req->rq_disk->disk_name, err); return MMC_BLK_CMD_ERR; } + + /* Timeout if the device never becomes ready for data + * and never leaves the program state. + */ + if (time_after(jiffies, timeout)) { + pr_err("%s: Card stuck in programming state!"\ + " %s %s\n", mmc_hostname(card->host), + req->rq_disk->disk_name, __func__); + + return MMC_BLK_CMD_ERR; + } /* * Some cards mishandle the status bits, * so make sure to check both the busy @@ -1504,6 +1583,8 @@ static struct mmc_blk_data *mmc_blk_alloc_req(struct mmc_card *card, md->disk->queue = md->queue.queue; md->disk->driverfs_dev = parent; set_disk_ro(md->disk, md->read_only || default_ro); + if (area_type & MMC_BLK_DATA_AREA_RPMB) + md->disk->flags |= GENHD_FL_NO_PART_SCAN; /* * As discussed on lkml, GENHD_FL_REMOVABLE should: diff --git a/drivers/mmc/card/queue.c b/drivers/mmc/card/queue.c index e360a979857d..fadf52eb5d70 100644 --- a/drivers/mmc/card/queue.c +++ b/drivers/mmc/card/queue.c @@ -68,6 +68,16 @@ static int mmc_queue_thread(void *d) if (req || mq->mqrq_prev->req) { set_current_state(TASK_RUNNING); mq->issue_fn(mq, req); + + /* + * Current request becomes previous request + * and vice versa. + */ + mq->mqrq_prev->brq.mrq.data = NULL; + mq->mqrq_prev->req = NULL; + tmp = mq->mqrq_prev; + mq->mqrq_prev = mq->mqrq_cur; + mq->mqrq_cur = tmp; } else { if (kthread_should_stop()) { set_current_state(TASK_RUNNING); @@ -77,13 +87,6 @@ static int mmc_queue_thread(void *d) schedule(); down(&mq->thread_sem); } - - /* Current request becomes previous request and vice versa. */ - mq->mqrq_prev->brq.mrq.data = NULL; - mq->mqrq_prev->req = NULL; - tmp = mq->mqrq_prev; - mq->mqrq_prev = mq->mqrq_cur; - mq->mqrq_cur = tmp; } while (1); up(&mq->thread_sem); diff --git a/drivers/mmc/core/bus.c b/drivers/mmc/core/bus.c index 9b68933f27e7..420cb6753c1e 100644 --- a/drivers/mmc/core/bus.c +++ b/drivers/mmc/core/bus.c @@ -225,8 +225,7 @@ static void mmc_release_card(struct device *dev) sdio_free_common_cis(card); - if (card->info) - kfree(card->info); + kfree(card->info); kfree(card); } diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c index 06c42cfb7c34..aaed7687cf09 100644 --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -42,6 +42,9 @@ #include "sd_ops.h" #include "sdio_ops.h" +/* If the device is not responding */ +#define MMC_CORE_TIMEOUT_MS (10 * 60 * 1000) /* 10 minute timeout */ + /* * Background operations can take a long time, depending on the housekeeping * operations the card has to perform. @@ -1631,6 +1634,7 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from, { struct mmc_command cmd = {0}; unsigned int qty = 0; + unsigned long timeout; int err; /* @@ -1708,6 +1712,7 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from, if (mmc_host_is_spi(card->host)) goto out; + timeout = jiffies + msecs_to_jiffies(MMC_CORE_TIMEOUT_MS); do { memset(&cmd, 0, sizeof(struct mmc_command)); cmd.opcode = MMC_SEND_STATUS; @@ -1721,8 +1726,19 @@ static int mmc_do_erase(struct mmc_card *card, unsigned int from, err = -EIO; goto out; } + + /* Timeout if the device never becomes ready for data and + * never leaves the program state. + */ + if (time_after(jiffies, timeout)) { + pr_err("%s: Card stuck in programming state! %s\n", + mmc_hostname(card->host), __func__); + err = -EIO; + goto out; + } + } while (!(cmd.resp[0] & R1_READY_FOR_DATA) || - R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG); + (R1_CURRENT_STATE(cmd.resp[0]) == R1_STATE_PRG)); out: return err; } @@ -1942,6 +1958,20 @@ int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen) } EXPORT_SYMBOL(mmc_set_blocklen); +int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount, + bool is_rel_write) +{ + struct mmc_command cmd = {0}; + + cmd.opcode = MMC_SET_BLOCK_COUNT; + cmd.arg = blockcount & 0x0000FFFF; + if (is_rel_write) + cmd.arg |= 1 << 31; + cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_AC; + return mmc_wait_for_cmd(card->host, &cmd, 5); +} +EXPORT_SYMBOL(mmc_set_blockcount); + static void mmc_hw_reset_for_init(struct mmc_host *host) { if (!(host->caps & MMC_CAP_HW_RESET) || !host->ops->hw_reset) diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c index d96c643dde1c..35c2f85b1956 100644 --- a/drivers/mmc/core/debugfs.c +++ b/drivers/mmc/core/debugfs.c @@ -144,6 +144,22 @@ static int mmc_ios_show(struct seq_file *s, void *data) } seq_printf(s, "timing spec:\t%u (%s)\n", ios->timing, str); + switch (ios->signal_voltage) { + case MMC_SIGNAL_VOLTAGE_330: + str = "3.30 V"; + break; + case MMC_SIGNAL_VOLTAGE_180: + str = "1.80 V"; + break; + case MMC_SIGNAL_VOLTAGE_120: + str = "1.20 V"; + break; + default: + str = "invalid"; + break; + } + seq_printf(s, "signal voltage:\t%u (%s)\n", ios->chip_select, str); + return 0; } diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c index 7cc46382fd64..e6e39111e05b 100644 --- a/drivers/mmc/core/mmc.c +++ b/drivers/mmc/core/mmc.c @@ -239,7 +239,7 @@ static void mmc_select_card_type(struct mmc_card *card) { struct mmc_host *host = card->host; u8 card_type = card->ext_csd.raw_card_type & EXT_CSD_CARD_TYPE_MASK; - unsigned int caps = host->caps, caps2 = host->caps2; + u32 caps = host->caps, caps2 = host->caps2; unsigned int hs_max_dtr = 0; if (card_type & EXT_CSD_CARD_TYPE_26) @@ -491,6 +491,17 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd) card->ext_csd.rel_param = ext_csd[EXT_CSD_WR_REL_PARAM]; card->ext_csd.rst_n_function = ext_csd[EXT_CSD_RST_N_FUNCTION]; + + /* + * RPMB regions are defined in multiples of 128K. + */ + card->ext_csd.raw_rpmb_size_mult = ext_csd[EXT_CSD_RPMB_MULT]; + if (ext_csd[EXT_CSD_RPMB_MULT]) { + mmc_part_add(card, ext_csd[EXT_CSD_RPMB_MULT] << 17, + EXT_CSD_PART_CONFIG_ACC_RPMB, + "rpmb", 0, false, + MMC_BLK_DATA_AREA_RPMB); + } } card->ext_csd.raw_erased_mem_count = ext_csd[EXT_CSD_ERASED_MEM_CONT]; @@ -615,6 +626,8 @@ MMC_DEV_ATTR(serial, "0x%08x\n", card->cid.serial); MMC_DEV_ATTR(enhanced_area_offset, "%llu\n", card->ext_csd.enhanced_area_offset); MMC_DEV_ATTR(enhanced_area_size, "%u\n", card->ext_csd.enhanced_area_size); +MMC_DEV_ATTR(raw_rpmb_size_mult, "%#x\n", card->ext_csd.raw_rpmb_size_mult); +MMC_DEV_ATTR(rel_sectors, "%#x\n", card->ext_csd.rel_sectors); static struct attribute *mmc_std_attrs[] = { &dev_attr_cid.attr, @@ -630,6 +643,8 @@ static struct attribute *mmc_std_attrs[] = { &dev_attr_serial.attr, &dev_attr_enhanced_area_offset.attr, &dev_attr_enhanced_area_size.attr, + &dev_attr_raw_rpmb_size_mult.attr, + &dev_attr_rel_sectors.attr, NULL, }; @@ -1051,6 +1066,8 @@ static int mmc_init_card(struct mmc_host *host, u32 ocr, if (mmc_card_highspeed(card) || mmc_card_hs200(card)) { if (max_dtr > card->ext_csd.hs_max_dtr) max_dtr = card->ext_csd.hs_max_dtr; + if (mmc_card_highspeed(card) && (max_dtr > 52000000)) + max_dtr = 52000000; } else if (max_dtr > card->csd.max_dtr) { max_dtr = card->csd.max_dtr; } diff --git a/drivers/mmc/core/mmc_ops.c b/drivers/mmc/core/mmc_ops.c index a0e172042e65..6d8f7012d73a 100644 --- a/drivers/mmc/core/mmc_ops.c +++ b/drivers/mmc/core/mmc_ops.c @@ -21,6 +21,8 @@ #include "core.h" #include "mmc_ops.h" +#define MMC_OPS_TIMEOUT_MS (10 * 60 * 1000) /* 10 minute timeout */ + static int _mmc_select_card(struct mmc_host *host, struct mmc_card *card) { int err; @@ -409,6 +411,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value, { int err; struct mmc_command cmd = {0}; + unsigned long timeout; u32 status; BUG_ON(!card); @@ -437,6 +440,7 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value, return 0; /* Must check status to be sure of no errors */ + timeout = jiffies + msecs_to_jiffies(MMC_OPS_TIMEOUT_MS); do { err = mmc_send_status(card, &status); if (err) @@ -445,6 +449,13 @@ int __mmc_switch(struct mmc_card *card, u8 set, u8 index, u8 value, break; if (mmc_host_is_spi(card->host)) break; + + /* Timeout if the device never leaves the program state. */ + if (time_after(jiffies, timeout)) { + pr_err("%s: Card stuck in programming state! %s\n", + mmc_hostname(card->host), __func__); + return -ETIMEDOUT; + } } while (R1_CURRENT_STATE(status) == R1_STATE_PRG); if (mmc_host_is_spi(card->host)) { diff --git a/drivers/mmc/core/sdio_bus.c b/drivers/mmc/core/sdio_bus.c index 6bf68799fe97..5e57048e2c1d 100644 --- a/drivers/mmc/core/sdio_bus.c +++ b/drivers/mmc/core/sdio_bus.c @@ -193,7 +193,21 @@ static int sdio_bus_remove(struct device *dev) } #ifdef CONFIG_PM + +#ifdef CONFIG_PM_SLEEP +static int pm_no_operation(struct device *dev) +{ + /* + * Prevent the PM core from calling SDIO device drivers' suspend + * callback routines, which it is not supposed to do, by using this + * empty function as the bus type suspend callaback for SDIO. + */ + return 0; +} +#endif + static const struct dev_pm_ops sdio_bus_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(pm_no_operation, pm_no_operation) SET_RUNTIME_PM_OPS( pm_generic_runtime_suspend, pm_generic_runtime_resume, @@ -258,8 +272,7 @@ static void sdio_release_func(struct device *dev) sdio_free_func_cis(func); - if (func->info) - kfree(func->info); + kfree(func->info); kfree(func); } diff --git a/drivers/mmc/core/sdio_io.c b/drivers/mmc/core/sdio_io.c index 8f6f5ac131fc..78cb4d5d9d58 100644 --- a/drivers/mmc/core/sdio_io.c +++ b/drivers/mmc/core/sdio_io.c @@ -188,8 +188,7 @@ EXPORT_SYMBOL_GPL(sdio_set_block_size); */ static inline unsigned int sdio_max_byte_size(struct sdio_func *func) { - unsigned mval = min(func->card->host->max_seg_size, - func->card->host->max_blk_size); + unsigned mval = func->card->host->max_blk_size; if (mmc_blksz_for_byte_mode(func->card)) mval = min(mval, func->cur_blksize); @@ -311,11 +310,8 @@ static int sdio_io_rw_ext_helper(struct sdio_func *func, int write, /* Do the bulk of the transfer using block mode (if supported). */ if (func->card->cccr.multi_block && (size > sdio_max_byte_size(func))) { /* Blocks per command is limited by host count, host transfer - * size (we only use a single sg entry) and the maximum for - * IO_RW_EXTENDED of 511 blocks. */ - max_blocks = min(func->card->host->max_blk_count, - func->card->host->max_seg_size / func->cur_blksize); - max_blocks = min(max_blocks, 511u); + * size and the maximum for IO_RW_EXTENDED of 511 blocks. */ + max_blocks = min(func->card->host->max_blk_count, 511u); while (remainder >= func->cur_blksize) { unsigned blocks; diff --git a/drivers/mmc/core/sdio_ops.c b/drivers/mmc/core/sdio_ops.c index d29e20630eed..62508b457c4f 100644 --- a/drivers/mmc/core/sdio_ops.c +++ b/drivers/mmc/core/sdio_ops.c @@ -124,7 +124,10 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn, struct mmc_request mrq = {NULL}; struct mmc_command cmd = {0}; struct mmc_data data = {0}; - struct scatterlist sg; + struct scatterlist sg, *sg_ptr; + struct sg_table sgtable; + unsigned int nents, left_size, i; + unsigned int seg_size = card->host->max_seg_size; BUG_ON(!card); BUG_ON(fn > 7); @@ -152,15 +155,36 @@ int mmc_io_rw_extended(struct mmc_card *card, int write, unsigned fn, /* Code in host drivers/fwk assumes that "blocks" always is >=1 */ data.blocks = blocks ? blocks : 1; data.flags = write ? MMC_DATA_WRITE : MMC_DATA_READ; - data.sg = &sg; - data.sg_len = 1; - sg_init_one(&sg, buf, data.blksz * data.blocks); + left_size = data.blksz * data.blocks; + nents = (left_size - 1) / seg_size + 1; + if (nents > 1) { + if (sg_alloc_table(&sgtable, nents, GFP_KERNEL)) + return -ENOMEM; + + data.sg = sgtable.sgl; + data.sg_len = nents; + + for_each_sg(data.sg, sg_ptr, data.sg_len, i) { + sg_set_page(sg_ptr, virt_to_page(buf + (i * seg_size)), + min(seg_size, left_size), + offset_in_page(buf + (i * seg_size))); + left_size = left_size - seg_size; + } + } else { + data.sg = &sg; + data.sg_len = 1; + + sg_init_one(&sg, buf, left_size); + } mmc_set_data_timeout(&data, card); mmc_wait_for_req(card->host, &mrq); + if (nents > 1) + sg_free_table(&sgtable); + if (cmd.error) return cmd.error; if (data.error) diff --git a/drivers/mmc/core/slot-gpio.c b/drivers/mmc/core/slot-gpio.c index 08c6b3dfe080..16a1c0b6f264 100644 --- a/drivers/mmc/core/slot-gpio.c +++ b/drivers/mmc/core/slot-gpio.c @@ -27,7 +27,13 @@ struct mmc_gpio { static irqreturn_t mmc_gpio_cd_irqt(int irq, void *dev_id) { /* Schedule a card detection after a debounce timeout */ - mmc_detect_change(dev_id, msecs_to_jiffies(100)); + struct mmc_host *host = dev_id; + + if (host->ops->card_event) + host->ops->card_event(host); + + mmc_detect_change(host, msecs_to_jiffies(200)); + return IRQ_HANDLED; } diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig index 9bf10e7bbfaf..83eb1e06ff76 100644 --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -270,26 +270,8 @@ config MMC_AU1X If unsure, say N. -choice - prompt "Atmel SD/MMC Driver" - depends on AVR32 || ARCH_AT91 - default MMC_ATMELMCI if AVR32 - help - Choose which driver to use for the Atmel MCI Silicon - -config MMC_AT91 - tristate "AT91 SD/MMC Card Interface support (DEPRECATED)" - depends on ARCH_AT91 - help - This selects the AT91 MCI controller. This driver will - be removed soon (for more information have a look to - Documentation/feature-removal-schedule.txt). Please use - MMC_ATMEL_MCI. - - If unsure, say N. - config MMC_ATMELMCI - tristate "Atmel Multimedia Card Interface support" + tristate "Atmel SD/MMC Driver (Multimedia Card Interface)" depends on AVR32 || ARCH_AT91 help This selects the Atmel Multimedia Card Interface driver. If @@ -298,8 +280,6 @@ config MMC_ATMELMCI If unsure, say N. -endchoice - config MMC_ATMELMCI_DMA bool "Atmel MCI DMA support" depends on MMC_ATMELMCI && (AVR32 || ARCH_AT91SAM9G45) && DMA_ENGINE @@ -621,3 +601,14 @@ config MMC_USHC Note: These controllers only support SDIO cards and do not support MMC or SD memory cards. + +config MMC_WMT + tristate "Wondermedia SD/MMC Host Controller support" + depends on ARCH_VT8500 + default y + help + This selects support for the SD/MMC Host Controller on + Wondermedia WM8505/WM8650 based SoCs. + + To compile this driver as a module, choose M here: the + module will be called wmt-sdmmc. diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile index 17ad0a7ba40b..39d5e1234709 100644 --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -17,7 +17,6 @@ obj-$(CONFIG_MMC_WBSD) += wbsd.o obj-$(CONFIG_MMC_AU1X) += au1xmmc.o obj-$(CONFIG_MMC_OMAP) += omap.o obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o -obj-$(CONFIG_MMC_AT91) += at91_mci.o obj-$(CONFIG_MMC_ATMELMCI) += atmel-mci.o obj-$(CONFIG_MMC_TIFM_SD) += tifm_sd.o obj-$(CONFIG_MMC_MSM) += msm_sdcc.o @@ -45,6 +44,7 @@ obj-$(CONFIG_MMC_SH_MMCIF) += sh_mmcif.o obj-$(CONFIG_MMC_JZ4740) += jz4740_mmc.o obj-$(CONFIG_MMC_VUB300) += vub300.o obj-$(CONFIG_MMC_USHC) += ushc.o +obj-$(CONFIG_MMC_WMT) += wmt-sdmmc.o obj-$(CONFIG_MMC_SDHCI_PLTFM) += sdhci-pltfm.o obj-$(CONFIG_MMC_SDHCI_CNS3XXX) += sdhci-cns3xxx.o diff --git a/drivers/mmc/host/at91_mci.c b/drivers/mmc/host/at91_mci.c deleted file mode 100644 index 74bed0fc23e7..000000000000 --- a/drivers/mmc/host/at91_mci.c +++ /dev/null @@ -1,1219 +0,0 @@ -/* - * linux/drivers/mmc/host/at91_mci.c - ATMEL AT91 MCI Driver - * - * Copyright (C) 2005 Cougar Creek Computing Devices Ltd, All Rights Reserved - * - * Copyright (C) 2006 Malcolm Noyes - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -/* - This is the AT91 MCI driver that has been tested with both MMC cards - and SD-cards. Boards that support write protect are now supported. - The CCAT91SBC001 board does not support SD cards. - - The three entry points are at91_mci_request, at91_mci_set_ios - and at91_mci_get_ro. - - SET IOS - This configures the device to put it into the correct mode and clock speed - required. - - MCI REQUEST - MCI request processes the commands sent in the mmc_request structure. This - can consist of a processing command and a stop command in the case of - multiple block transfers. - - There are three main types of request, commands, reads and writes. - - Commands are straight forward. The command is submitted to the controller and - the request function returns. When the controller generates an interrupt to indicate - the command is finished, the response to the command are read and the mmc_request_done - function called to end the request. - - Reads and writes work in a similar manner to normal commands but involve the PDC (DMA) - controller to manage the transfers. - - A read is done from the controller directly to the scatterlist passed in from the request. - Due to a bug in the AT91RM9200 controller, when a read is completed, all the words are byte - swapped in the scatterlist buffers. AT91SAM926x are not affected by this bug. - - The sequence of read interrupts is: ENDRX, RXBUFF, CMDRDY - - A write is slightly different in that the bytes to write are read from the scatterlist - into a dma memory buffer (this is in case the source buffer should be read only). The - entire write buffer is then done from this single dma memory buffer. - - The sequence of write interrupts is: ENDTX, TXBUFE, NOTBUSY, CMDRDY - - GET RO - Gets the status of the write protect pin, if available. -*/ - -#include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/init.h> -#include <linux/ioport.h> -#include <linux/platform_device.h> -#include <linux/interrupt.h> -#include <linux/blkdev.h> -#include <linux/delay.h> -#include <linux/err.h> -#include <linux/dma-mapping.h> -#include <linux/clk.h> -#include <linux/atmel_pdc.h> -#include <linux/gfp.h> -#include <linux/highmem.h> - -#include <linux/mmc/host.h> -#include <linux/mmc/sdio.h> - -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/gpio.h> - -#include <mach/board.h> -#include <mach/cpu.h> - -#include "at91_mci.h" - -#define DRIVER_NAME "at91_mci" - -static inline int at91mci_is_mci1rev2xx(void) -{ - return ( cpu_is_at91sam9260() - || cpu_is_at91sam9263() - || cpu_is_at91sam9rl() - || cpu_is_at91sam9g10() - || cpu_is_at91sam9g20() - ); -} - -#define FL_SENT_COMMAND (1 << 0) -#define FL_SENT_STOP (1 << 1) - -#define AT91_MCI_ERRORS (AT91_MCI_RINDE | AT91_MCI_RDIRE | AT91_MCI_RCRCE \ - | AT91_MCI_RENDE | AT91_MCI_RTOE | AT91_MCI_DCRCE \ - | AT91_MCI_DTOE | AT91_MCI_OVRE | AT91_MCI_UNRE) - -#define at91_mci_read(host, reg) __raw_readl((host)->baseaddr + (reg)) -#define at91_mci_write(host, reg, val) __raw_writel((val), (host)->baseaddr + (reg)) - -#define MCI_BLKSIZE 512 -#define MCI_MAXBLKSIZE 4095 -#define MCI_BLKATONCE 256 -#define MCI_BUFSIZE (MCI_BLKSIZE * MCI_BLKATONCE) - -/* - * Low level type for this driver - */ -struct at91mci_host -{ - struct mmc_host *mmc; - struct mmc_command *cmd; - struct mmc_request *request; - - void __iomem *baseaddr; - int irq; - - struct at91_mmc_data *board; - int present; - - struct clk *mci_clk; - - /* - * Flag indicating when the command has been sent. This is used to - * work out whether or not to send the stop - */ - unsigned int flags; - /* flag for current bus settings */ - u32 bus_mode; - - /* DMA buffer used for transmitting */ - unsigned int* buffer; - dma_addr_t physical_address; - unsigned int total_length; - - /* Latest in the scatterlist that has been enabled for transfer, but not freed */ - int in_use_index; - - /* Latest in the scatterlist that has been enabled for transfer */ - int transfer_index; - - /* Timer for timeouts */ - struct timer_list timer; -}; - -/* - * Reset the controller and restore most of the state - */ -static void at91_reset_host(struct at91mci_host *host) -{ - unsigned long flags; - u32 mr; - u32 sdcr; - u32 dtor; - u32 imr; - - local_irq_save(flags); - imr = at91_mci_read(host, AT91_MCI_IMR); - - at91_mci_write(host, AT91_MCI_IDR, 0xffffffff); - - /* save current state */ - mr = at91_mci_read(host, AT91_MCI_MR) & 0x7fff; - sdcr = at91_mci_read(host, AT91_MCI_SDCR); - dtor = at91_mci_read(host, AT91_MCI_DTOR); - - /* reset the controller */ - at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST); - - /* restore state */ - at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN); - at91_mci_write(host, AT91_MCI_MR, mr); - at91_mci_write(host, AT91_MCI_SDCR, sdcr); - at91_mci_write(host, AT91_MCI_DTOR, dtor); - at91_mci_write(host, AT91_MCI_IER, imr); - - /* make sure sdio interrupts will fire */ - at91_mci_read(host, AT91_MCI_SR); - - local_irq_restore(flags); -} - -static void at91_timeout_timer(unsigned long data) -{ - struct at91mci_host *host; - - host = (struct at91mci_host *)data; - - if (host->request) { - dev_err(host->mmc->parent, "Timeout waiting end of packet\n"); - - if (host->cmd && host->cmd->data) { - host->cmd->data->error = -ETIMEDOUT; - } else { - if (host->cmd) - host->cmd->error = -ETIMEDOUT; - else - host->request->cmd->error = -ETIMEDOUT; - } - - at91_reset_host(host); - mmc_request_done(host->mmc, host->request); - } -} - -/* - * Copy from sg to a dma block - used for transfers - */ -static inline void at91_mci_sg_to_dma(struct at91mci_host *host, struct mmc_data *data) -{ - unsigned int len, i, size; - unsigned *dmabuf = host->buffer; - - size = data->blksz * data->blocks; - len = data->sg_len; - - /* MCI1 rev2xx Data Write Operation and number of bytes erratum */ - if (at91mci_is_mci1rev2xx()) - if (host->total_length == 12) - memset(dmabuf, 0, 12); - - /* - * Just loop through all entries. Size might not - * be the entire list though so make sure that - * we do not transfer too much. - */ - for (i = 0; i < len; i++) { - struct scatterlist *sg; - int amount; - unsigned int *sgbuffer; - - sg = &data->sg[i]; - - sgbuffer = kmap_atomic(sg_page(sg)) + sg->offset; - amount = min(size, sg->length); - size -= amount; - - if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */ - int index; - - for (index = 0; index < (amount / 4); index++) - *dmabuf++ = swab32(sgbuffer[index]); - } else { - char *tmpv = (char *)dmabuf; - memcpy(tmpv, sgbuffer, amount); - tmpv += amount; - dmabuf = (unsigned *)tmpv; - } - - kunmap_atomic(sgbuffer); - - if (size == 0) - break; - } - - /* - * Check that we didn't get a request to transfer - * more data than can fit into the SG list. - */ - BUG_ON(size != 0); -} - -/* - * Handle after a dma read - */ -static void at91_mci_post_dma_read(struct at91mci_host *host) -{ - struct mmc_command *cmd; - struct mmc_data *data; - unsigned int len, i, size; - unsigned *dmabuf = host->buffer; - - pr_debug("post dma read\n"); - - cmd = host->cmd; - if (!cmd) { - pr_debug("no command\n"); - return; - } - - data = cmd->data; - if (!data) { - pr_debug("no data\n"); - return; - } - - size = data->blksz * data->blocks; - len = data->sg_len; - - at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_ENDRX); - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_RXBUFF); - - for (i = 0; i < len; i++) { - struct scatterlist *sg; - int amount; - unsigned int *sgbuffer; - - sg = &data->sg[i]; - - sgbuffer = kmap_atomic(sg_page(sg)) + sg->offset; - amount = min(size, sg->length); - size -= amount; - - if (cpu_is_at91rm9200()) { /* AT91RM9200 errata */ - int index; - for (index = 0; index < (amount / 4); index++) - sgbuffer[index] = swab32(*dmabuf++); - } else { - char *tmpv = (char *)dmabuf; - memcpy(sgbuffer, tmpv, amount); - tmpv += amount; - dmabuf = (unsigned *)tmpv; - } - - flush_kernel_dcache_page(sg_page(sg)); - kunmap_atomic(sgbuffer); - data->bytes_xfered += amount; - if (size == 0) - break; - } - - pr_debug("post dma read done\n"); -} - -/* - * Handle transmitted data - */ -static void at91_mci_handle_transmitted(struct at91mci_host *host) -{ - struct mmc_command *cmd; - struct mmc_data *data; - - pr_debug("Handling the transmit\n"); - - /* Disable the transfer */ - at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS); - - /* Now wait for cmd ready */ - at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_TXBUFE); - - cmd = host->cmd; - if (!cmd) return; - - data = cmd->data; - if (!data) return; - - if (cmd->data->blocks > 1) { - pr_debug("multiple write : wait for BLKE...\n"); - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_BLKE); - } else - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY); -} - -/* - * Update bytes transfered count during a write operation - */ -static void at91_mci_update_bytes_xfered(struct at91mci_host *host) -{ - struct mmc_data *data; - - /* always deal with the effective request (and not the current cmd) */ - - if (host->request->cmd && host->request->cmd->error != 0) - return; - - if (host->request->data) { - data = host->request->data; - if (data->flags & MMC_DATA_WRITE) { - /* card is in IDLE mode now */ - pr_debug("-> bytes_xfered %d, total_length = %d\n", - data->bytes_xfered, host->total_length); - data->bytes_xfered = data->blksz * data->blocks; - } - } -} - - -/*Handle after command sent ready*/ -static int at91_mci_handle_cmdrdy(struct at91mci_host *host) -{ - if (!host->cmd) - return 1; - else if (!host->cmd->data) { - if (host->flags & FL_SENT_STOP) { - /*After multi block write, we must wait for NOTBUSY*/ - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY); - } else return 1; - } else if (host->cmd->data->flags & MMC_DATA_WRITE) { - /*After sendding multi-block-write command, start DMA transfer*/ - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_TXBUFE | AT91_MCI_BLKE); - at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN); - } - - /* command not completed, have to wait */ - return 0; -} - - -/* - * Enable the controller - */ -static void at91_mci_enable(struct at91mci_host *host) -{ - unsigned int mr; - - at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN); - at91_mci_write(host, AT91_MCI_IDR, 0xffffffff); - at91_mci_write(host, AT91_MCI_DTOR, AT91_MCI_DTOMUL_1M | AT91_MCI_DTOCYC); - mr = AT91_MCI_PDCMODE | 0x34a; - - if (at91mci_is_mci1rev2xx()) - mr |= AT91_MCI_RDPROOF | AT91_MCI_WRPROOF; - - at91_mci_write(host, AT91_MCI_MR, mr); - - /* use Slot A or B (only one at same time) */ - at91_mci_write(host, AT91_MCI_SDCR, host->board->slot_b); -} - -/* - * Disable the controller - */ -static void at91_mci_disable(struct at91mci_host *host) -{ - at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS | AT91_MCI_SWRST); -} - -/* - * Send a command - */ -static void at91_mci_send_command(struct at91mci_host *host, struct mmc_command *cmd) -{ - unsigned int cmdr, mr; - unsigned int block_length; - struct mmc_data *data = cmd->data; - - unsigned int blocks; - unsigned int ier = 0; - - host->cmd = cmd; - - /* Needed for leaving busy state before CMD1 */ - if ((at91_mci_read(host, AT91_MCI_SR) & AT91_MCI_RTOE) && (cmd->opcode == 1)) { - pr_debug("Clearing timeout\n"); - at91_mci_write(host, AT91_MCI_ARGR, 0); - at91_mci_write(host, AT91_MCI_CMDR, AT91_MCI_OPDCMD); - while (!(at91_mci_read(host, AT91_MCI_SR) & AT91_MCI_CMDRDY)) { - /* spin */ - pr_debug("Clearing: SR = %08X\n", at91_mci_read(host, AT91_MCI_SR)); - } - } - - cmdr = cmd->opcode; - - if (mmc_resp_type(cmd) == MMC_RSP_NONE) - cmdr |= AT91_MCI_RSPTYP_NONE; - else { - /* if a response is expected then allow maximum response latancy */ - cmdr |= AT91_MCI_MAXLAT; - /* set 136 bit response for R2, 48 bit response otherwise */ - if (mmc_resp_type(cmd) == MMC_RSP_R2) - cmdr |= AT91_MCI_RSPTYP_136; - else - cmdr |= AT91_MCI_RSPTYP_48; - } - - if (data) { - - if (cpu_is_at91rm9200() || cpu_is_at91sam9261()) { - if (data->blksz & 0x3) { - pr_debug("Unsupported block size\n"); - cmd->error = -EINVAL; - mmc_request_done(host->mmc, host->request); - return; - } - if (data->flags & MMC_DATA_STREAM) { - pr_debug("Stream commands not supported\n"); - cmd->error = -EINVAL; - mmc_request_done(host->mmc, host->request); - return; - } - } - - block_length = data->blksz; - blocks = data->blocks; - - /* always set data start - also set direction flag for read */ - if (data->flags & MMC_DATA_READ) - cmdr |= (AT91_MCI_TRDIR | AT91_MCI_TRCMD_START); - else if (data->flags & MMC_DATA_WRITE) - cmdr |= AT91_MCI_TRCMD_START; - - if (cmd->opcode == SD_IO_RW_EXTENDED) { - cmdr |= AT91_MCI_TRTYP_SDIO_BLOCK; - } else { - if (data->flags & MMC_DATA_STREAM) - cmdr |= AT91_MCI_TRTYP_STREAM; - if (data->blocks > 1) - cmdr |= AT91_MCI_TRTYP_MULTIPLE; - } - } - else { - block_length = 0; - blocks = 0; - } - - if (host->flags & FL_SENT_STOP) - cmdr |= AT91_MCI_TRCMD_STOP; - - if (host->bus_mode == MMC_BUSMODE_OPENDRAIN) - cmdr |= AT91_MCI_OPDCMD; - - /* - * Set the arguments and send the command - */ - pr_debug("Sending command %d as %08X, arg = %08X, blocks = %d, length = %d (MR = %08X)\n", - cmd->opcode, cmdr, cmd->arg, blocks, block_length, at91_mci_read(host, AT91_MCI_MR)); - - if (!data) { - at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTDIS | ATMEL_PDC_RXTDIS); - at91_mci_write(host, ATMEL_PDC_RPR, 0); - at91_mci_write(host, ATMEL_PDC_RCR, 0); - at91_mci_write(host, ATMEL_PDC_RNPR, 0); - at91_mci_write(host, ATMEL_PDC_RNCR, 0); - at91_mci_write(host, ATMEL_PDC_TPR, 0); - at91_mci_write(host, ATMEL_PDC_TCR, 0); - at91_mci_write(host, ATMEL_PDC_TNPR, 0); - at91_mci_write(host, ATMEL_PDC_TNCR, 0); - ier = AT91_MCI_CMDRDY; - } else { - /* zero block length and PDC mode */ - mr = at91_mci_read(host, AT91_MCI_MR) & 0x5fff; - mr |= (data->blksz & 0x3) ? AT91_MCI_PDCFBYTE : 0; - mr |= (block_length << 16); - mr |= AT91_MCI_PDCMODE; - at91_mci_write(host, AT91_MCI_MR, mr); - - if (!(cpu_is_at91rm9200() || cpu_is_at91sam9261())) - at91_mci_write(host, AT91_MCI_BLKR, - AT91_MCI_BLKR_BCNT(blocks) | - AT91_MCI_BLKR_BLKLEN(block_length)); - - /* - * Disable the PDC controller - */ - at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS); - - if (cmdr & AT91_MCI_TRCMD_START) { - data->bytes_xfered = 0; - host->transfer_index = 0; - host->in_use_index = 0; - if (cmdr & AT91_MCI_TRDIR) { - /* - * Handle a read - */ - host->total_length = 0; - - at91_mci_write(host, ATMEL_PDC_RPR, host->physical_address); - at91_mci_write(host, ATMEL_PDC_RCR, (data->blksz & 0x3) ? - (blocks * block_length) : (blocks * block_length) / 4); - at91_mci_write(host, ATMEL_PDC_RNPR, 0); - at91_mci_write(host, ATMEL_PDC_RNCR, 0); - - ier = AT91_MCI_ENDRX /* | AT91_MCI_RXBUFF */; - } - else { - /* - * Handle a write - */ - host->total_length = block_length * blocks; - /* - * MCI1 rev2xx Data Write Operation and - * number of bytes erratum - */ - if (at91mci_is_mci1rev2xx()) - if (host->total_length < 12) - host->total_length = 12; - - at91_mci_sg_to_dma(host, data); - - pr_debug("Transmitting %d bytes\n", host->total_length); - - at91_mci_write(host, ATMEL_PDC_TPR, host->physical_address); - at91_mci_write(host, ATMEL_PDC_TCR, (data->blksz & 0x3) ? - host->total_length : host->total_length / 4); - - ier = AT91_MCI_CMDRDY; - } - } - } - - /* - * Send the command and then enable the PDC - not the other way round as - * the data sheet says - */ - - at91_mci_write(host, AT91_MCI_ARGR, cmd->arg); - at91_mci_write(host, AT91_MCI_CMDR, cmdr); - - if (cmdr & AT91_MCI_TRCMD_START) { - if (cmdr & AT91_MCI_TRDIR) - at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN); - } - - /* Enable selected interrupts */ - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_ERRORS | ier); -} - -/* - * Process the next step in the request - */ -static void at91_mci_process_next(struct at91mci_host *host) -{ - if (!(host->flags & FL_SENT_COMMAND)) { - host->flags |= FL_SENT_COMMAND; - at91_mci_send_command(host, host->request->cmd); - } - else if ((!(host->flags & FL_SENT_STOP)) && host->request->stop) { - host->flags |= FL_SENT_STOP; - at91_mci_send_command(host, host->request->stop); - } else { - del_timer(&host->timer); - /* the at91rm9200 mci controller hangs after some transfers, - * and the workaround is to reset it after each transfer. - */ - if (cpu_is_at91rm9200()) - at91_reset_host(host); - mmc_request_done(host->mmc, host->request); - } -} - -/* - * Handle a command that has been completed - */ -static void at91_mci_completed_command(struct at91mci_host *host, unsigned int status) -{ - struct mmc_command *cmd = host->cmd; - struct mmc_data *data = cmd->data; - - at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); - - cmd->resp[0] = at91_mci_read(host, AT91_MCI_RSPR(0)); - cmd->resp[1] = at91_mci_read(host, AT91_MCI_RSPR(1)); - cmd->resp[2] = at91_mci_read(host, AT91_MCI_RSPR(2)); - cmd->resp[3] = at91_mci_read(host, AT91_MCI_RSPR(3)); - - pr_debug("Status = %08X/%08x [%08X %08X %08X %08X]\n", - status, at91_mci_read(host, AT91_MCI_SR), - cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3]); - - if (status & AT91_MCI_ERRORS) { - if ((status & AT91_MCI_RCRCE) && !(mmc_resp_type(cmd) & MMC_RSP_CRC)) { - cmd->error = 0; - } - else { - if (status & (AT91_MCI_DTOE | AT91_MCI_DCRCE)) { - if (data) { - if (status & AT91_MCI_DTOE) - data->error = -ETIMEDOUT; - else if (status & AT91_MCI_DCRCE) - data->error = -EILSEQ; - } - } else { - if (status & AT91_MCI_RTOE) - cmd->error = -ETIMEDOUT; - else if (status & AT91_MCI_RCRCE) - cmd->error = -EILSEQ; - else - cmd->error = -EIO; - } - - pr_debug("Error detected and set to %d/%d (cmd = %d, retries = %d)\n", - cmd->error, data ? data->error : 0, - cmd->opcode, cmd->retries); - } - } - else - cmd->error = 0; - - at91_mci_process_next(host); -} - -/* - * Handle an MMC request - */ -static void at91_mci_request(struct mmc_host *mmc, struct mmc_request *mrq) -{ - struct at91mci_host *host = mmc_priv(mmc); - host->request = mrq; - host->flags = 0; - - /* more than 1s timeout needed with slow SD cards */ - mod_timer(&host->timer, jiffies + msecs_to_jiffies(2000)); - - at91_mci_process_next(host); -} - -/* - * Set the IOS - */ -static void at91_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) -{ - int clkdiv; - struct at91mci_host *host = mmc_priv(mmc); - unsigned long at91_master_clock = clk_get_rate(host->mci_clk); - - host->bus_mode = ios->bus_mode; - - if (ios->clock == 0) { - /* Disable the MCI controller */ - at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIDIS); - clkdiv = 0; - } - else { - /* Enable the MCI controller */ - at91_mci_write(host, AT91_MCI_CR, AT91_MCI_MCIEN); - - if ((at91_master_clock % (ios->clock * 2)) == 0) - clkdiv = ((at91_master_clock / ios->clock) / 2) - 1; - else - clkdiv = (at91_master_clock / ios->clock) / 2; - - pr_debug("clkdiv = %d. mcck = %ld\n", clkdiv, - at91_master_clock / (2 * (clkdiv + 1))); - } - if (ios->bus_width == MMC_BUS_WIDTH_4 && host->board->wire4) { - pr_debug("MMC: Setting controller bus width to 4\n"); - at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) | AT91_MCI_SDCBUS); - } - else { - pr_debug("MMC: Setting controller bus width to 1\n"); - at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS); - } - - /* Set the clock divider */ - at91_mci_write(host, AT91_MCI_MR, (at91_mci_read(host, AT91_MCI_MR) & ~AT91_MCI_CLKDIV) | clkdiv); - - /* maybe switch power to the card */ - if (gpio_is_valid(host->board->vcc_pin)) { - switch (ios->power_mode) { - case MMC_POWER_OFF: - gpio_set_value(host->board->vcc_pin, 0); - break; - case MMC_POWER_UP: - gpio_set_value(host->board->vcc_pin, 1); - break; - case MMC_POWER_ON: - break; - default: - WARN_ON(1); - } - } -} - -/* - * Handle an interrupt - */ -static irqreturn_t at91_mci_irq(int irq, void *devid) -{ - struct at91mci_host *host = devid; - int completed = 0; - unsigned int int_status, int_mask; - - int_status = at91_mci_read(host, AT91_MCI_SR); - int_mask = at91_mci_read(host, AT91_MCI_IMR); - - pr_debug("MCI irq: status = %08X, %08X, %08X\n", int_status, int_mask, - int_status & int_mask); - - int_status = int_status & int_mask; - - if (int_status & AT91_MCI_ERRORS) { - completed = 1; - - if (int_status & AT91_MCI_UNRE) - pr_debug("MMC: Underrun error\n"); - if (int_status & AT91_MCI_OVRE) - pr_debug("MMC: Overrun error\n"); - if (int_status & AT91_MCI_DTOE) - pr_debug("MMC: Data timeout\n"); - if (int_status & AT91_MCI_DCRCE) - pr_debug("MMC: CRC error in data\n"); - if (int_status & AT91_MCI_RTOE) - pr_debug("MMC: Response timeout\n"); - if (int_status & AT91_MCI_RENDE) - pr_debug("MMC: Response end bit error\n"); - if (int_status & AT91_MCI_RCRCE) - pr_debug("MMC: Response CRC error\n"); - if (int_status & AT91_MCI_RDIRE) - pr_debug("MMC: Response direction error\n"); - if (int_status & AT91_MCI_RINDE) - pr_debug("MMC: Response index error\n"); - } else { - /* Only continue processing if no errors */ - - if (int_status & AT91_MCI_TXBUFE) { - pr_debug("TX buffer empty\n"); - at91_mci_handle_transmitted(host); - } - - if (int_status & AT91_MCI_ENDRX) { - pr_debug("ENDRX\n"); - at91_mci_post_dma_read(host); - } - - if (int_status & AT91_MCI_RXBUFF) { - pr_debug("RX buffer full\n"); - at91_mci_write(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS); - at91_mci_write(host, AT91_MCI_IDR, AT91_MCI_RXBUFF | AT91_MCI_ENDRX); - completed = 1; - } - - if (int_status & AT91_MCI_ENDTX) - pr_debug("Transmit has ended\n"); - - if (int_status & AT91_MCI_NOTBUSY) { - pr_debug("Card is ready\n"); - at91_mci_update_bytes_xfered(host); - completed = 1; - } - - if (int_status & AT91_MCI_DTIP) - pr_debug("Data transfer in progress\n"); - - if (int_status & AT91_MCI_BLKE) { - pr_debug("Block transfer has ended\n"); - if (host->request->data && host->request->data->blocks > 1) { - /* multi block write : complete multi write - * command and send stop */ - completed = 1; - } else { - at91_mci_write(host, AT91_MCI_IER, AT91_MCI_NOTBUSY); - } - } - - if (int_status & AT91_MCI_SDIOIRQA) - mmc_signal_sdio_irq(host->mmc); - - if (int_status & AT91_MCI_SDIOIRQB) - mmc_signal_sdio_irq(host->mmc); - - if (int_status & AT91_MCI_TXRDY) - pr_debug("Ready to transmit\n"); - - if (int_status & AT91_MCI_RXRDY) - pr_debug("Ready to receive\n"); - - if (int_status & AT91_MCI_CMDRDY) { - pr_debug("Command ready\n"); - completed = at91_mci_handle_cmdrdy(host); - } - } - - if (completed) { - pr_debug("Completed command\n"); - at91_mci_write(host, AT91_MCI_IDR, 0xffffffff & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); - at91_mci_completed_command(host, int_status); - } else - at91_mci_write(host, AT91_MCI_IDR, int_status & ~(AT91_MCI_SDIOIRQA | AT91_MCI_SDIOIRQB)); - - return IRQ_HANDLED; -} - -static irqreturn_t at91_mmc_det_irq(int irq, void *_host) -{ - struct at91mci_host *host = _host; - int present; - - /* entering this ISR means that we have configured det_pin: - * we can use its value in board structure */ - present = !gpio_get_value(host->board->det_pin); - - /* - * we expect this irq on both insert and remove, - * and use a short delay to debounce. - */ - if (present != host->present) { - host->present = present; - pr_debug("%s: card %s\n", mmc_hostname(host->mmc), - present ? "insert" : "remove"); - if (!present) { - pr_debug("****** Resetting SD-card bus width ******\n"); - at91_mci_write(host, AT91_MCI_SDCR, at91_mci_read(host, AT91_MCI_SDCR) & ~AT91_MCI_SDCBUS); - } - /* 0.5s needed because of early card detect switch firing */ - mmc_detect_change(host->mmc, msecs_to_jiffies(500)); - } - return IRQ_HANDLED; -} - -static int at91_mci_get_ro(struct mmc_host *mmc) -{ - struct at91mci_host *host = mmc_priv(mmc); - - if (gpio_is_valid(host->board->wp_pin)) - return !!gpio_get_value(host->board->wp_pin); - /* - * Board doesn't support read only detection; let the mmc core - * decide what to do. - */ - return -ENOSYS; -} - -static void at91_mci_enable_sdio_irq(struct mmc_host *mmc, int enable) -{ - struct at91mci_host *host = mmc_priv(mmc); - - pr_debug("%s: sdio_irq %c : %s\n", mmc_hostname(host->mmc), - host->board->slot_b ? 'B':'A', enable ? "enable" : "disable"); - at91_mci_write(host, enable ? AT91_MCI_IER : AT91_MCI_IDR, - host->board->slot_b ? AT91_MCI_SDIOIRQB : AT91_MCI_SDIOIRQA); - -} - -static const struct mmc_host_ops at91_mci_ops = { - .request = at91_mci_request, - .set_ios = at91_mci_set_ios, - .get_ro = at91_mci_get_ro, - .enable_sdio_irq = at91_mci_enable_sdio_irq, -}; - -/* - * Probe for the device - */ -static int __init at91_mci_probe(struct platform_device *pdev) -{ - struct mmc_host *mmc; - struct at91mci_host *host; - struct resource *res; - int ret; - - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - if (!res) - return -ENXIO; - - if (!request_mem_region(res->start, resource_size(res), DRIVER_NAME)) - return -EBUSY; - - mmc = mmc_alloc_host(sizeof(struct at91mci_host), &pdev->dev); - if (!mmc) { - ret = -ENOMEM; - dev_dbg(&pdev->dev, "couldn't allocate mmc host\n"); - goto fail6; - } - - mmc->ops = &at91_mci_ops; - mmc->f_min = 375000; - mmc->f_max = 25000000; - mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; - mmc->caps = 0; - - mmc->max_blk_size = MCI_MAXBLKSIZE; - mmc->max_blk_count = MCI_BLKATONCE; - mmc->max_req_size = MCI_BUFSIZE; - mmc->max_segs = MCI_BLKATONCE; - mmc->max_seg_size = MCI_BUFSIZE; - - host = mmc_priv(mmc); - host->mmc = mmc; - host->bus_mode = 0; - host->board = pdev->dev.platform_data; - if (host->board->wire4) { - if (at91mci_is_mci1rev2xx()) - mmc->caps |= MMC_CAP_4_BIT_DATA; - else - dev_warn(&pdev->dev, "4 wire bus mode not supported" - " - using 1 wire\n"); - } - - host->buffer = dma_alloc_coherent(&pdev->dev, MCI_BUFSIZE, - &host->physical_address, GFP_KERNEL); - if (!host->buffer) { - ret = -ENOMEM; - dev_err(&pdev->dev, "Can't allocate transmit buffer\n"); - goto fail5; - } - - /* Add SDIO capability when available */ - if (at91mci_is_mci1rev2xx()) { - /* at91mci MCI1 rev2xx sdio interrupt erratum */ - if (host->board->wire4 || !host->board->slot_b) - mmc->caps |= MMC_CAP_SDIO_IRQ; - } - - /* - * Reserve GPIOs ... board init code makes sure these pins are set - * up as GPIOs with the right direction (input, except for vcc) - */ - if (gpio_is_valid(host->board->det_pin)) { - ret = gpio_request(host->board->det_pin, "mmc_detect"); - if (ret < 0) { - dev_dbg(&pdev->dev, "couldn't claim card detect pin\n"); - goto fail4b; - } - } - if (gpio_is_valid(host->board->wp_pin)) { - ret = gpio_request(host->board->wp_pin, "mmc_wp"); - if (ret < 0) { - dev_dbg(&pdev->dev, "couldn't claim wp sense pin\n"); - goto fail4; - } - } - if (gpio_is_valid(host->board->vcc_pin)) { - ret = gpio_request(host->board->vcc_pin, "mmc_vcc"); - if (ret < 0) { - dev_dbg(&pdev->dev, "couldn't claim vcc switch pin\n"); - goto fail3; - } - } - - /* - * Get Clock - */ - host->mci_clk = clk_get(&pdev->dev, "mci_clk"); - if (IS_ERR(host->mci_clk)) { - ret = -ENODEV; - dev_dbg(&pdev->dev, "no mci_clk?\n"); - goto fail2; - } - - /* - * Map I/O region - */ - host->baseaddr = ioremap(res->start, resource_size(res)); - if (!host->baseaddr) { - ret = -ENOMEM; - goto fail1; - } - - /* - * Reset hardware - */ - clk_enable(host->mci_clk); /* Enable the peripheral clock */ - at91_mci_disable(host); - at91_mci_enable(host); - - /* - * Allocate the MCI interrupt - */ - host->irq = platform_get_irq(pdev, 0); - ret = request_irq(host->irq, at91_mci_irq, IRQF_SHARED, - mmc_hostname(mmc), host); - if (ret) { - dev_dbg(&pdev->dev, "request MCI interrupt failed\n"); - goto fail0; - } - - setup_timer(&host->timer, at91_timeout_timer, (unsigned long)host); - - platform_set_drvdata(pdev, mmc); - - /* - * Add host to MMC layer - */ - if (gpio_is_valid(host->board->det_pin)) { - host->present = !gpio_get_value(host->board->det_pin); - } - else - host->present = -1; - - mmc_add_host(mmc); - - /* - * monitor card insertion/removal if we can - */ - if (gpio_is_valid(host->board->det_pin)) { - ret = request_irq(gpio_to_irq(host->board->det_pin), - at91_mmc_det_irq, 0, mmc_hostname(mmc), host); - if (ret) - dev_warn(&pdev->dev, "request MMC detect irq failed\n"); - else - device_init_wakeup(&pdev->dev, 1); - } - - pr_debug("Added MCI driver\n"); - - return 0; - -fail0: - clk_disable(host->mci_clk); - iounmap(host->baseaddr); -fail1: - clk_put(host->mci_clk); -fail2: - if (gpio_is_valid(host->board->vcc_pin)) - gpio_free(host->board->vcc_pin); -fail3: - if (gpio_is_valid(host->board->wp_pin)) - gpio_free(host->board->wp_pin); -fail4: - if (gpio_is_valid(host->board->det_pin)) - gpio_free(host->board->det_pin); -fail4b: - if (host->buffer) - dma_free_coherent(&pdev->dev, MCI_BUFSIZE, - host->buffer, host->physical_address); -fail5: - mmc_free_host(mmc); -fail6: - release_mem_region(res->start, resource_size(res)); - dev_err(&pdev->dev, "probe failed, err %d\n", ret); - return ret; -} - -/* - * Remove a device - */ -static int __exit at91_mci_remove(struct platform_device *pdev) -{ - struct mmc_host *mmc = platform_get_drvdata(pdev); - struct at91mci_host *host; - struct resource *res; - - if (!mmc) - return -1; - - host = mmc_priv(mmc); - - if (host->buffer) - dma_free_coherent(&pdev->dev, MCI_BUFSIZE, - host->buffer, host->physical_address); - - if (gpio_is_valid(host->board->det_pin)) { - if (device_can_wakeup(&pdev->dev)) - free_irq(gpio_to_irq(host->board->det_pin), host); - device_init_wakeup(&pdev->dev, 0); - gpio_free(host->board->det_pin); - } - - at91_mci_disable(host); - del_timer_sync(&host->timer); - mmc_remove_host(mmc); - free_irq(host->irq, host); - - clk_disable(host->mci_clk); /* Disable the peripheral clock */ - clk_put(host->mci_clk); - - if (gpio_is_valid(host->board->vcc_pin)) - gpio_free(host->board->vcc_pin); - if (gpio_is_valid(host->board->wp_pin)) - gpio_free(host->board->wp_pin); - - iounmap(host->baseaddr); - res = platform_get_resource(pdev, IORESOURCE_MEM, 0); - release_mem_region(res->start, resource_size(res)); - - mmc_free_host(mmc); - platform_set_drvdata(pdev, NULL); - pr_debug("MCI Removed\n"); - - return 0; -} - -#ifdef CONFIG_PM -static int at91_mci_suspend(struct platform_device *pdev, pm_message_t state) -{ - struct mmc_host *mmc = platform_get_drvdata(pdev); - struct at91mci_host *host = mmc_priv(mmc); - int ret = 0; - - if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev)) - enable_irq_wake(host->board->det_pin); - - if (mmc) - ret = mmc_suspend_host(mmc); - - return ret; -} - -static int at91_mci_resume(struct platform_device *pdev) -{ - struct mmc_host *mmc = platform_get_drvdata(pdev); - struct at91mci_host *host = mmc_priv(mmc); - int ret = 0; - - if (gpio_is_valid(host->board->det_pin) && device_may_wakeup(&pdev->dev)) - disable_irq_wake(host->board->det_pin); - - if (mmc) - ret = mmc_resume_host(mmc); - - return ret; -} -#else -#define at91_mci_suspend NULL -#define at91_mci_resume NULL -#endif - -static struct platform_driver at91_mci_driver = { - .remove = __exit_p(at91_mci_remove), - .suspend = at91_mci_suspend, - .resume = at91_mci_resume, - .driver = { - .name = DRIVER_NAME, - .owner = THIS_MODULE, - }, -}; - -static int __init at91_mci_init(void) -{ - return platform_driver_probe(&at91_mci_driver, at91_mci_probe); -} - -static void __exit at91_mci_exit(void) -{ - platform_driver_unregister(&at91_mci_driver); -} - -module_init(at91_mci_init); -module_exit(at91_mci_exit); - -MODULE_DESCRIPTION("AT91 Multimedia Card Interface driver"); -MODULE_AUTHOR("Nick Randell"); -MODULE_LICENSE("GPL"); -MODULE_ALIAS("platform:at91_mci"); diff --git a/drivers/mmc/host/at91_mci.h b/drivers/mmc/host/at91_mci.h deleted file mode 100644 index eec3a6b1c2bc..000000000000 --- a/drivers/mmc/host/at91_mci.h +++ /dev/null @@ -1,115 +0,0 @@ -/* - * drivers/mmc/host/at91_mci.h - * - * Copyright (C) 2005 Ivan Kokshaysky - * Copyright (C) SAN People - * - * MultiMedia Card Interface (MCI) registers. - * Based on AT91RM9200 datasheet revision F. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef AT91_MCI_H -#define AT91_MCI_H - -#define AT91_MCI_CR 0x00 /* Control Register */ -#define AT91_MCI_MCIEN (1 << 0) /* Multi-Media Interface Enable */ -#define AT91_MCI_MCIDIS (1 << 1) /* Multi-Media Interface Disable */ -#define AT91_MCI_PWSEN (1 << 2) /* Power Save Mode Enable */ -#define AT91_MCI_PWSDIS (1 << 3) /* Power Save Mode Disable */ -#define AT91_MCI_SWRST (1 << 7) /* Software Reset */ - -#define AT91_MCI_MR 0x04 /* Mode Register */ -#define AT91_MCI_CLKDIV (0xff << 0) /* Clock Divider */ -#define AT91_MCI_PWSDIV (7 << 8) /* Power Saving Divider */ -#define AT91_MCI_RDPROOF (1 << 11) /* Read Proof Enable [SAM926[03] only] */ -#define AT91_MCI_WRPROOF (1 << 12) /* Write Proof Enable [SAM926[03] only] */ -#define AT91_MCI_PDCFBYTE (1 << 13) /* PDC Force Byte Transfer [SAM926[03] only] */ -#define AT91_MCI_PDCPADV (1 << 14) /* PDC Padding Value */ -#define AT91_MCI_PDCMODE (1 << 15) /* PDC-orientated Mode */ -#define AT91_MCI_BLKLEN (0xfff << 18) /* Data Block Length */ - -#define AT91_MCI_DTOR 0x08 /* Data Timeout Register */ -#define AT91_MCI_DTOCYC (0xf << 0) /* Data Timeout Cycle Number */ -#define AT91_MCI_DTOMUL (7 << 4) /* Data Timeout Multiplier */ -#define AT91_MCI_DTOMUL_1 (0 << 4) -#define AT91_MCI_DTOMUL_16 (1 << 4) -#define AT91_MCI_DTOMUL_128 (2 << 4) -#define AT91_MCI_DTOMUL_256 (3 << 4) -#define AT91_MCI_DTOMUL_1K (4 << 4) -#define AT91_MCI_DTOMUL_4K (5 << 4) -#define AT91_MCI_DTOMUL_64K (6 << 4) -#define AT91_MCI_DTOMUL_1M (7 << 4) - -#define AT91_MCI_SDCR 0x0c /* SD Card Register */ -#define AT91_MCI_SDCSEL (3 << 0) /* SD Card Selector */ -#define AT91_MCI_SDCBUS (1 << 7) /* 1-bit or 4-bit bus */ - -#define AT91_MCI_ARGR 0x10 /* Argument Register */ - -#define AT91_MCI_CMDR 0x14 /* Command Register */ -#define AT91_MCI_CMDNB (0x3f << 0) /* Command Number */ -#define AT91_MCI_RSPTYP (3 << 6) /* Response Type */ -#define AT91_MCI_RSPTYP_NONE (0 << 6) -#define AT91_MCI_RSPTYP_48 (1 << 6) -#define AT91_MCI_RSPTYP_136 (2 << 6) -#define AT91_MCI_SPCMD (7 << 8) /* Special Command */ -#define AT91_MCI_SPCMD_NONE (0 << 8) -#define AT91_MCI_SPCMD_INIT (1 << 8) -#define AT91_MCI_SPCMD_SYNC (2 << 8) -#define AT91_MCI_SPCMD_ICMD (4 << 8) -#define AT91_MCI_SPCMD_IRESP (5 << 8) -#define AT91_MCI_OPDCMD (1 << 11) /* Open Drain Command */ -#define AT91_MCI_MAXLAT (1 << 12) /* Max Latency for Command to Response */ -#define AT91_MCI_TRCMD (3 << 16) /* Transfer Command */ -#define AT91_MCI_TRCMD_NONE (0 << 16) -#define AT91_MCI_TRCMD_START (1 << 16) -#define AT91_MCI_TRCMD_STOP (2 << 16) -#define AT91_MCI_TRDIR (1 << 18) /* Transfer Direction */ -#define AT91_MCI_TRTYP (3 << 19) /* Transfer Type */ -#define AT91_MCI_TRTYP_BLOCK (0 << 19) -#define AT91_MCI_TRTYP_MULTIPLE (1 << 19) -#define AT91_MCI_TRTYP_STREAM (2 << 19) -#define AT91_MCI_TRTYP_SDIO_BYTE (4 << 19) -#define AT91_MCI_TRTYP_SDIO_BLOCK (5 << 19) - -#define AT91_MCI_BLKR 0x18 /* Block Register */ -#define AT91_MCI_BLKR_BCNT(n) ((0xffff & (n)) << 0) /* Block count */ -#define AT91_MCI_BLKR_BLKLEN(n) ((0xffff & (n)) << 16) /* Block length */ - -#define AT91_MCI_RSPR(n) (0x20 + ((n) * 4)) /* Response Registers 0-3 */ -#define AT91_MCR_RDR 0x30 /* Receive Data Register */ -#define AT91_MCR_TDR 0x34 /* Transmit Data Register */ - -#define AT91_MCI_SR 0x40 /* Status Register */ -#define AT91_MCI_CMDRDY (1 << 0) /* Command Ready */ -#define AT91_MCI_RXRDY (1 << 1) /* Receiver Ready */ -#define AT91_MCI_TXRDY (1 << 2) /* Transmit Ready */ -#define AT91_MCI_BLKE (1 << 3) /* Data Block Ended */ -#define AT91_MCI_DTIP (1 << 4) /* Data Transfer in Progress */ -#define AT91_MCI_NOTBUSY (1 << 5) /* Data Not Busy */ -#define AT91_MCI_ENDRX (1 << 6) /* End of RX Buffer */ -#define AT91_MCI_ENDTX (1 << 7) /* End fo TX Buffer */ -#define AT91_MCI_SDIOIRQA (1 << 8) /* SDIO Interrupt for Slot A */ -#define AT91_MCI_SDIOIRQB (1 << 9) /* SDIO Interrupt for Slot B */ -#define AT91_MCI_RXBUFF (1 << 14) /* RX Buffer Full */ -#define AT91_MCI_TXBUFE (1 << 15) /* TX Buffer Empty */ -#define AT91_MCI_RINDE (1 << 16) /* Response Index Error */ -#define AT91_MCI_RDIRE (1 << 17) /* Response Direction Error */ -#define AT91_MCI_RCRCE (1 << 18) /* Response CRC Error */ -#define AT91_MCI_RENDE (1 << 19) /* Response End Bit Error */ -#define AT91_MCI_RTOE (1 << 20) /* Response Time-out Error */ -#define AT91_MCI_DCRCE (1 << 21) /* Data CRC Error */ -#define AT91_MCI_DTOE (1 << 22) /* Data Time-out Error */ -#define AT91_MCI_OVRE (1 << 30) /* Overrun */ -#define AT91_MCI_UNRE (1 << 31) /* Underrun */ - -#define AT91_MCI_IER 0x44 /* Interrupt Enable Register */ -#define AT91_MCI_IDR 0x48 /* Interrupt Disable Register */ -#define AT91_MCI_IMR 0x4c /* Interrupt Mask Register */ - -#endif diff --git a/drivers/mmc/host/dw_mmc-pci.c b/drivers/mmc/host/dw_mmc-pci.c index edb37e9135ae..53a09cbb2c7c 100644 --- a/drivers/mmc/host/dw_mmc-pci.c +++ b/drivers/mmc/host/dw_mmc-pci.c @@ -134,7 +134,7 @@ static struct pci_driver dw_mci_pci_driver = { .name = "dw_mmc_pci", .id_table = dw_mci_pci_id, .probe = dw_mci_pci_probe, - .remove = dw_mci_pci_remove, + .remove = __devexit_p(dw_mci_pci_remove), .driver = { .pm = &dw_mci_pci_pmops }, diff --git a/drivers/mmc/host/dw_mmc-pltfm.c b/drivers/mmc/host/dw_mmc-pltfm.c index 917936bee5d5..4e133709e33d 100644 --- a/drivers/mmc/host/dw_mmc-pltfm.c +++ b/drivers/mmc/host/dw_mmc-pltfm.c @@ -119,7 +119,8 @@ static const struct of_device_id dw_mci_pltfm_match[] = { MODULE_DEVICE_TABLE(of, dw_mci_pltfm_match); static struct platform_driver dw_mci_pltfm_driver = { - .remove = __exit_p(dw_mci_pltfm_remove), + .probe = dw_mci_pltfm_probe, + .remove = __devexit_p(dw_mci_pltfm_remove), .driver = { .name = "dw_mmc", .of_match_table = of_match_ptr(dw_mci_pltfm_match), @@ -127,18 +128,7 @@ static struct platform_driver dw_mci_pltfm_driver = { }, }; -static int __init dw_mci_init(void) -{ - return platform_driver_probe(&dw_mci_pltfm_driver, dw_mci_pltfm_probe); -} - -static void __exit dw_mci_exit(void) -{ - platform_driver_unregister(&dw_mci_pltfm_driver); -} - -module_init(dw_mci_init); -module_exit(dw_mci_exit); +module_platform_driver(dw_mci_pltfm_driver); MODULE_DESCRIPTION("DW Multimedia Card Interface driver"); MODULE_AUTHOR("NXP Semiconductor VietNam"); diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c index c0667c8af2bd..323c5022c2ca 100644 --- a/drivers/mmc/host/dw_mmc.c +++ b/drivers/mmc/host/dw_mmc.c @@ -232,7 +232,7 @@ static u32 dw_mci_prepare_command(struct mmc_host *mmc, struct mmc_command *cmd) { struct mmc_data *data; struct dw_mci_slot *slot = mmc_priv(mmc); - struct dw_mci_drv_data *drv_data = slot->host->drv_data; + const struct dw_mci_drv_data *drv_data = slot->host->drv_data; u32 cmdr; cmd->error = -EINPROGRESS; @@ -617,13 +617,13 @@ static void mci_send_cmd(struct dw_mci_slot *slot, u32 cmd, u32 arg) cmd, arg, cmd_status); } -static void dw_mci_setup_bus(struct dw_mci_slot *slot) +static void dw_mci_setup_bus(struct dw_mci_slot *slot, bool force_clkinit) { struct dw_mci *host = slot->host; u32 div; u32 clk_en_a; - if (slot->clock != host->current_speed) { + if (slot->clock != host->current_speed || force_clkinit) { div = host->bus_hz / slot->clock; if (host->bus_hz % slot->clock && host->bus_hz > slot->clock) /* @@ -683,9 +683,6 @@ static void __dw_mci_start_request(struct dw_mci *host, if (host->pdata->select_slot) host->pdata->select_slot(slot->id); - /* Slot specific timing and width adjustment */ - dw_mci_setup_bus(slot); - host->cur_slot = slot; host->mrq = mrq; @@ -773,22 +770,19 @@ static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq) static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) { struct dw_mci_slot *slot = mmc_priv(mmc); - struct dw_mci_drv_data *drv_data = slot->host->drv_data; + const struct dw_mci_drv_data *drv_data = slot->host->drv_data; u32 regs; - /* set default 1 bit mode */ - slot->ctype = SDMMC_CTYPE_1BIT; - switch (ios->bus_width) { - case MMC_BUS_WIDTH_1: - slot->ctype = SDMMC_CTYPE_1BIT; - break; case MMC_BUS_WIDTH_4: slot->ctype = SDMMC_CTYPE_4BIT; break; case MMC_BUS_WIDTH_8: slot->ctype = SDMMC_CTYPE_8BIT; break; + default: + /* set default 1 bit mode */ + slot->ctype = SDMMC_CTYPE_1BIT; } regs = mci_readl(slot->host, UHS_REG); @@ -812,6 +806,9 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) if (drv_data && drv_data->set_ios) drv_data->set_ios(slot->host, ios); + /* Slot specific timing and width adjustment */ + dw_mci_setup_bus(slot, false); + switch (ios->power_mode) { case MMC_POWER_UP: set_bit(DW_MMC_CARD_NEED_INIT, &slot->flags); @@ -1817,7 +1814,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id) { struct mmc_host *mmc; struct dw_mci_slot *slot; - struct dw_mci_drv_data *drv_data = host->drv_data; + const struct dw_mci_drv_data *drv_data = host->drv_data; int ctrl_id, ret; u8 bus_width; @@ -1850,6 +1847,9 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id) if (host->pdata->caps) mmc->caps = host->pdata->caps; + if (host->pdata->pm_caps) + mmc->pm_caps = host->pdata->pm_caps; + if (host->dev->of_node) { ctrl_id = of_alias_get_id(host->dev->of_node, "mshc"); if (ctrl_id < 0) @@ -1911,7 +1911,7 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id) #endif /* CONFIG_MMC_DW_IDMAC */ } - host->vmmc = regulator_get(mmc_dev(mmc), "vmmc"); + host->vmmc = devm_regulator_get(mmc_dev(mmc), "vmmc"); if (IS_ERR(host->vmmc)) { pr_info("%s: no vmmc regulator found\n", mmc_hostname(mmc)); host->vmmc = NULL; @@ -1960,7 +1960,7 @@ static void dw_mci_cleanup_slot(struct dw_mci_slot *slot, unsigned int id) static void dw_mci_init_dma(struct dw_mci *host) { /* Alloc memory for sg translation */ - host->sg_cpu = dma_alloc_coherent(host->dev, PAGE_SIZE, + host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE, &host->sg_dma, GFP_KERNEL); if (!host->sg_cpu) { dev_err(host->dev, "%s: could not alloc DMA memory\n", @@ -2038,7 +2038,7 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host) struct dw_mci_board *pdata; struct device *dev = host->dev; struct device_node *np = dev->of_node; - struct dw_mci_drv_data *drv_data = host->drv_data; + const struct dw_mci_drv_data *drv_data = host->drv_data; int idx, ret; pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); @@ -2072,6 +2072,12 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host) return ERR_PTR(ret); } + if (of_find_property(np, "keep-power-in-suspend", NULL)) + pdata->pm_caps |= MMC_PM_KEEP_POWER; + + if (of_find_property(np, "enable-sdio-wakeup", NULL)) + pdata->pm_caps |= MMC_PM_WAKE_SDIO_IRQ; + return pdata; } @@ -2084,7 +2090,7 @@ static struct dw_mci_board *dw_mci_parse_dt(struct dw_mci *host) int dw_mci_probe(struct dw_mci *host) { - struct dw_mci_drv_data *drv_data = host->drv_data; + const struct dw_mci_drv_data *drv_data = host->drv_data; int width, i, ret = 0; u32 fifo_size; int init_slots = 0; @@ -2103,26 +2109,24 @@ int dw_mci_probe(struct dw_mci *host) return -ENODEV; } - host->biu_clk = clk_get(host->dev, "biu"); + host->biu_clk = devm_clk_get(host->dev, "biu"); if (IS_ERR(host->biu_clk)) { dev_dbg(host->dev, "biu clock not available\n"); } else { ret = clk_prepare_enable(host->biu_clk); if (ret) { dev_err(host->dev, "failed to enable biu clock\n"); - clk_put(host->biu_clk); return ret; } } - host->ciu_clk = clk_get(host->dev, "ciu"); + host->ciu_clk = devm_clk_get(host->dev, "ciu"); if (IS_ERR(host->ciu_clk)) { dev_dbg(host->dev, "ciu clock not available\n"); } else { ret = clk_prepare_enable(host->ciu_clk); if (ret) { dev_err(host->dev, "failed to enable ciu clock\n"); - clk_put(host->ciu_clk); goto err_clk_biu; } } @@ -2224,7 +2228,8 @@ int dw_mci_probe(struct dw_mci *host) if (!host->card_workqueue) goto err_dmaunmap; INIT_WORK(&host->card_work, dw_mci_work_routine_card); - ret = request_irq(host->irq, dw_mci_interrupt, host->irq_flags, "dw-mci", host); + ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt, + host->irq_flags, "dw-mci", host); if (ret) goto err_workqueue; @@ -2262,7 +2267,7 @@ int dw_mci_probe(struct dw_mci *host) } else { dev_dbg(host->dev, "attempted to initialize %d slots, " "but failed on all\n", host->num_slots); - goto err_init_slot; + goto err_workqueue; } /* @@ -2282,33 +2287,24 @@ int dw_mci_probe(struct dw_mci *host) return 0; -err_init_slot: - free_irq(host->irq, host); - err_workqueue: destroy_workqueue(host->card_workqueue); err_dmaunmap: if (host->use_dma && host->dma_ops->exit) host->dma_ops->exit(host); - dma_free_coherent(host->dev, PAGE_SIZE, - host->sg_cpu, host->sg_dma); - if (host->vmmc) { + if (host->vmmc) regulator_disable(host->vmmc); - regulator_put(host->vmmc); - } err_clk_ciu: - if (!IS_ERR(host->ciu_clk)) { + if (!IS_ERR(host->ciu_clk)) clk_disable_unprepare(host->ciu_clk); - clk_put(host->ciu_clk); - } + err_clk_biu: - if (!IS_ERR(host->biu_clk)) { + if (!IS_ERR(host->biu_clk)) clk_disable_unprepare(host->biu_clk); - clk_put(host->biu_clk); - } + return ret; } EXPORT_SYMBOL(dw_mci_probe); @@ -2330,24 +2326,19 @@ void dw_mci_remove(struct dw_mci *host) mci_writel(host, CLKENA, 0); mci_writel(host, CLKSRC, 0); - free_irq(host->irq, host); destroy_workqueue(host->card_workqueue); - dma_free_coherent(host->dev, PAGE_SIZE, host->sg_cpu, host->sg_dma); if (host->use_dma && host->dma_ops->exit) host->dma_ops->exit(host); - if (host->vmmc) { + if (host->vmmc) regulator_disable(host->vmmc); - regulator_put(host->vmmc); - } if (!IS_ERR(host->ciu_clk)) clk_disable_unprepare(host->ciu_clk); + if (!IS_ERR(host->biu_clk)) clk_disable_unprepare(host->biu_clk); - clk_put(host->ciu_clk); - clk_put(host->biu_clk); } EXPORT_SYMBOL(dw_mci_remove); @@ -2411,6 +2402,11 @@ int dw_mci_resume(struct dw_mci *host) struct dw_mci_slot *slot = host->slot[i]; if (!slot) continue; + if (slot->mmc->pm_flags & MMC_PM_KEEP_POWER) { + dw_mci_set_ios(slot->mmc, &slot->mmc->ios); + dw_mci_setup_bus(slot, true); + } + ret = mmc_resume_host(host->slot[i]->mmc); if (ret < 0) return ret; diff --git a/drivers/mmc/host/mxcmmc.c b/drivers/mmc/host/mxcmmc.c index 6290b7f1ccfe..29e680f193a0 100644 --- a/drivers/mmc/host/mxcmmc.c +++ b/drivers/mmc/host/mxcmmc.c @@ -240,7 +240,7 @@ static int mxcmci_setup_data(struct mxcmci_host *host, struct mmc_data *data) return 0; for_each_sg(data->sg, sg, data->sg_len, i) { - if (sg->offset & 3 || sg->length & 3) { + if (sg->offset & 3 || sg->length & 3 || sg->length < 512) { host->do_dma = 0; return 0; } diff --git a/drivers/mmc/host/mxs-mmc.c b/drivers/mmc/host/mxs-mmc.c index 80d1e6d4b0ae..206fe499ded5 100644 --- a/drivers/mmc/host/mxs-mmc.c +++ b/drivers/mmc/host/mxs-mmc.c @@ -43,7 +43,6 @@ #include <linux/module.h> #include <linux/pinctrl/consumer.h> #include <linux/stmp_device.h> -#include <linux/mmc/mxs-mmc.h> #include <linux/spi/mxs-spi.h> #define DRIVER_NAME "mxs-mmc" @@ -593,13 +592,13 @@ static int mxs_mmc_probe(struct platform_device *pdev) struct mxs_mmc_host *host; struct mmc_host *mmc; struct resource *iores, *dmares; - struct mxs_mmc_platform_data *pdata; struct pinctrl *pinctrl; int ret = 0, irq_err, irq_dma; dma_cap_mask_t mask; struct regulator *reg_vmmc; enum of_gpio_flags flags; struct mxs_ssp *ssp; + u32 bus_width = 0; iores = platform_get_resource(pdev, IORESOURCE_MEM, 0); dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0); @@ -682,25 +681,15 @@ static int mxs_mmc_probe(struct platform_device *pdev) mmc->caps = MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SDIO_IRQ | MMC_CAP_NEEDS_POLL; - pdata = mmc_dev(host->mmc)->platform_data; - if (!pdata) { - u32 bus_width = 0; - of_property_read_u32(np, "bus-width", &bus_width); - if (bus_width == 4) - mmc->caps |= MMC_CAP_4_BIT_DATA; - else if (bus_width == 8) - mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA; - host->wp_gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, - &flags); - if (flags & OF_GPIO_ACTIVE_LOW) - host->wp_inverted = 1; - } else { - if (pdata->flags & SLOTF_8_BIT_CAPABLE) - mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA; - if (pdata->flags & SLOTF_4_BIT_CAPABLE) - mmc->caps |= MMC_CAP_4_BIT_DATA; - host->wp_gpio = pdata->wp_gpio; - } + of_property_read_u32(np, "bus-width", &bus_width); + if (bus_width == 4) + mmc->caps |= MMC_CAP_4_BIT_DATA; + else if (bus_width == 8) + mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA; + host->wp_gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags); + + if (flags & OF_GPIO_ACTIVE_LOW) + host->wp_inverted = 1; mmc->f_min = 400000; mmc->f_max = 288000000; diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c index fedd258cc4ea..d0a912fbad3b 100644 --- a/drivers/mmc/host/omap_hsmmc.c +++ b/drivers/mmc/host/omap_hsmmc.c @@ -37,6 +37,7 @@ #include <linux/io.h> #include <linux/gpio.h> #include <linux/regulator/consumer.h> +#include <linux/pinctrl/consumer.h> #include <linux/pm_runtime.h> #include <mach/hardware.h> #include <plat/mmc.h> @@ -62,6 +63,7 @@ #define VS18 (1 << 26) #define VS30 (1 << 25) +#define HSS (1 << 21) #define SDVS18 (0x5 << 9) #define SDVS30 (0x6 << 9) #define SDVS33 (0x7 << 9) @@ -78,28 +80,17 @@ #define CLKD_SHIFT 6 #define DTO_MASK 0x000F0000 #define DTO_SHIFT 16 -#define INT_EN_MASK 0x307F0033 -#define BWR_ENABLE (1 << 4) -#define BRR_ENABLE (1 << 5) -#define DTO_ENABLE (1 << 20) #define INIT_STREAM (1 << 1) #define DP_SELECT (1 << 21) #define DDIR (1 << 4) -#define DMA_EN 0x1 +#define DMAE 0x1 #define MSBS (1 << 5) #define BCE (1 << 1) #define FOUR_BIT (1 << 1) +#define HSPE (1 << 2) #define DDR (1 << 19) #define DW8 (1 << 5) -#define CC 0x1 -#define TC 0x02 #define OD 0x1 -#define ERR (1 << 15) -#define CMD_TIMEOUT (1 << 16) -#define DATA_TIMEOUT (1 << 20) -#define CMD_CRC (1 << 17) -#define DATA_CRC (1 << 21) -#define CARD_ERR (1 << 28) #define STAT_CLEAR 0xFFFFFFFF #define INIT_STREAM_CMD 0x00000000 #define DUAL_VOLT_OCR_BIT 7 @@ -108,6 +99,26 @@ #define SOFTRESET (1 << 1) #define RESETDONE (1 << 0) +/* Interrupt masks for IE and ISE register */ +#define CC_EN (1 << 0) +#define TC_EN (1 << 1) +#define BWR_EN (1 << 4) +#define BRR_EN (1 << 5) +#define ERR_EN (1 << 15) +#define CTO_EN (1 << 16) +#define CCRC_EN (1 << 17) +#define CEB_EN (1 << 18) +#define CIE_EN (1 << 19) +#define DTO_EN (1 << 20) +#define DCRC_EN (1 << 21) +#define DEB_EN (1 << 22) +#define CERR_EN (1 << 28) +#define BADA_EN (1 << 29) + +#define INT_EN_MASK (BADA_EN | CERR_EN | DEB_EN | DCRC_EN |\ + DTO_EN | CIE_EN | CEB_EN | CCRC_EN | CTO_EN | \ + BRR_EN | BWR_EN | TC_EN | CC_EN) + #define MMC_AUTOSUSPEND_DELAY 100 #define MMC_TIMEOUT_MS 20 #define OMAP_MMC_MIN_CLOCK 400000 @@ -302,7 +313,7 @@ static int omap_hsmmc_reg_get(struct omap_hsmmc_host *host) reg = regulator_get(host->dev, "vmmc"); if (IS_ERR(reg)) { - dev_dbg(host->dev, "vmmc regulator missing\n"); + dev_err(host->dev, "vmmc regulator missing\n"); return PTR_ERR(reg); } else { mmc_slot(host).set_power = omap_hsmmc_set_power; @@ -455,13 +466,13 @@ static void omap_hsmmc_enable_irq(struct omap_hsmmc_host *host, unsigned int irq_mask; if (host->use_dma) - irq_mask = INT_EN_MASK & ~(BRR_ENABLE | BWR_ENABLE); + irq_mask = INT_EN_MASK & ~(BRR_EN | BWR_EN); else irq_mask = INT_EN_MASK; /* Disable timeout for erases */ if (cmd->opcode == MMC_ERASE) - irq_mask &= ~DTO_ENABLE; + irq_mask &= ~DTO_EN; OMAP_HSMMC_WRITE(host->base, STAT, STAT_CLEAR); OMAP_HSMMC_WRITE(host->base, ISE, irq_mask); @@ -494,6 +505,7 @@ static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host) struct mmc_ios *ios = &host->mmc->ios; unsigned long regval; unsigned long timeout; + unsigned long clkdiv; dev_vdbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock); @@ -501,7 +513,8 @@ static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host) regval = OMAP_HSMMC_READ(host->base, SYSCTL); regval = regval & ~(CLKD_MASK | DTO_MASK); - regval = regval | (calc_divisor(host, ios) << 6) | (DTO << 16); + clkdiv = calc_divisor(host, ios); + regval = regval | (clkdiv << 6) | (DTO << 16); OMAP_HSMMC_WRITE(host->base, SYSCTL, regval); OMAP_HSMMC_WRITE(host->base, SYSCTL, OMAP_HSMMC_READ(host->base, SYSCTL) | ICE); @@ -512,6 +525,27 @@ static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host) && time_before(jiffies, timeout)) cpu_relax(); + /* + * Enable High-Speed Support + * Pre-Requisites + * - Controller should support High-Speed-Enable Bit + * - Controller should not be using DDR Mode + * - Controller should advertise that it supports High Speed + * in capabilities register + * - MMC/SD clock coming out of controller > 25MHz + */ + if ((mmc_slot(host).features & HSMMC_HAS_HSPE_SUPPORT) && + (ios->timing != MMC_TIMING_UHS_DDR50) && + ((OMAP_HSMMC_READ(host->base, CAPA) & HSS) == HSS)) { + regval = OMAP_HSMMC_READ(host->base, HCTL); + if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000) + regval |= HSPE; + else + regval &= ~HSPE; + + OMAP_HSMMC_WRITE(host->base, HCTL, regval); + } + omap_hsmmc_start_clock(host); } @@ -676,8 +710,8 @@ static void send_init_stream(struct omap_hsmmc_host *host) OMAP_HSMMC_WRITE(host->base, CMD, INIT_STREAM_CMD); timeout = jiffies + msecs_to_jiffies(MMC_TIMEOUT_MS); - while ((reg != CC) && time_before(jiffies, timeout)) - reg = OMAP_HSMMC_READ(host->base, STAT) & CC; + while ((reg != CC_EN) && time_before(jiffies, timeout)) + reg = OMAP_HSMMC_READ(host->base, STAT) & CC_EN; OMAP_HSMMC_WRITE(host->base, CON, OMAP_HSMMC_READ(host->base, CON) & ~INIT_STREAM); @@ -768,7 +802,7 @@ omap_hsmmc_start_command(struct omap_hsmmc_host *host, struct mmc_command *cmd, } if (host->use_dma) - cmdreg |= DMA_EN; + cmdreg |= DMAE; host->req_in_progress = 1; @@ -968,16 +1002,20 @@ static inline void omap_hsmmc_reset_controller_fsm(struct omap_hsmmc_host *host, __func__); } -static void hsmmc_command_incomplete(struct omap_hsmmc_host *host, int err) +static void hsmmc_command_incomplete(struct omap_hsmmc_host *host, + int err, int end_cmd) { - omap_hsmmc_reset_controller_fsm(host, SRC); - host->cmd->error = err; + if (end_cmd) { + omap_hsmmc_reset_controller_fsm(host, SRC); + if (host->cmd) + host->cmd->error = err; + } if (host->data) { omap_hsmmc_reset_controller_fsm(host, SRD); omap_hsmmc_dma_cleanup(host, err); - } - + } else if (host->mrq && host->mrq->cmd) + host->mrq->cmd->error = err; } static void omap_hsmmc_do_irq(struct omap_hsmmc_host *host, int status) @@ -988,23 +1026,25 @@ static void omap_hsmmc_do_irq(struct omap_hsmmc_host *host, int status) data = host->data; dev_vdbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status); - if (status & ERR) { + if (status & ERR_EN) { omap_hsmmc_dbg_report_irq(host, status); - if (status & (CMD_TIMEOUT | DATA_TIMEOUT)) - hsmmc_command_incomplete(host, -ETIMEDOUT); - else if (status & (CMD_CRC | DATA_CRC)) - hsmmc_command_incomplete(host, -EILSEQ); - end_cmd = 1; + if (status & (CTO_EN | CCRC_EN)) + end_cmd = 1; + if (status & (CTO_EN | DTO_EN)) + hsmmc_command_incomplete(host, -ETIMEDOUT, end_cmd); + else if (status & (CCRC_EN | DCRC_EN)) + hsmmc_command_incomplete(host, -EILSEQ, end_cmd); + if (host->data || host->response_busy) { - end_trans = 1; + end_trans = !end_cmd; host->response_busy = 0; } } - if (end_cmd || ((status & CC) && host->cmd)) + if (end_cmd || ((status & CC_EN) && host->cmd)) omap_hsmmc_cmd_done(host, host->cmd); - if ((end_trans || (status & TC)) && host->mrq) + if ((end_trans || (status & TC_EN)) && host->mrq) omap_hsmmc_xfer_done(host, data); } @@ -1101,7 +1141,7 @@ static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host *host, int vdd) return 0; err: - dev_dbg(mmc_dev(host->mmc), "Unable to switch operating voltage\n"); + dev_err(mmc_dev(host->mmc), "Unable to switch operating voltage\n"); return ret; } @@ -1360,7 +1400,7 @@ omap_hsmmc_prepare_data(struct omap_hsmmc_host *host, struct mmc_request *req) if (host->use_dma) { ret = omap_hsmmc_start_dma_transfer(host, req); if (ret != 0) { - dev_dbg(mmc_dev(host->mmc), "MMC start dma failure\n"); + dev_err(mmc_dev(host->mmc), "MMC start dma failure\n"); return ret; } } @@ -1678,7 +1718,7 @@ static struct omap_mmc_platform_data *of_get_hsmmc_pdata(struct device *dev) { struct omap_mmc_platform_data *pdata; struct device_node *np = dev->of_node; - u32 bus_width; + u32 bus_width, max_freq; pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) @@ -1705,6 +1745,12 @@ static struct omap_mmc_platform_data *of_get_hsmmc_pdata(struct device *dev) if (of_find_property(np, "ti,needs-special-reset", NULL)) pdata->slots[0].features |= HSMMC_HAS_UPDATED_RESET; + if (!of_property_read_u32(np, "max-frequency", &max_freq)) + pdata->max_freq = max_freq; + + if (of_find_property(np, "ti,needs-special-hs-handling", NULL)) + pdata->slots[0].features |= HSMMC_HAS_HSPE_SUPPORT; + return pdata; } #else @@ -1725,6 +1771,7 @@ static int __devinit omap_hsmmc_probe(struct platform_device *pdev) const struct of_device_id *match; dma_cap_mask_t mask; unsigned tx_req, rx_req; + struct pinctrl *pinctrl; match = of_match_device(of_match_ptr(omap_mmc_of_match), &pdev->dev); if (match) { @@ -1821,7 +1868,6 @@ static int __devinit omap_hsmmc_probe(struct platform_device *pdev) * MMC can still work without debounce clock. */ if (IS_ERR(host->dbclk)) { - dev_warn(mmc_dev(host->mmc), "Failed to get debounce clk\n"); host->dbclk = NULL; } else if (clk_prepare_enable(host->dbclk) != 0) { dev_warn(mmc_dev(host->mmc), "Failed to enable debounce clk\n"); @@ -1889,13 +1935,13 @@ static int __devinit omap_hsmmc_probe(struct platform_device *pdev) ret = request_irq(host->irq, omap_hsmmc_irq, 0, mmc_hostname(mmc), host); if (ret) { - dev_dbg(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n"); + dev_err(mmc_dev(host->mmc), "Unable to grab HSMMC IRQ\n"); goto err_irq; } if (pdata->init != NULL) { if (pdata->init(&pdev->dev) != 0) { - dev_dbg(mmc_dev(host->mmc), + dev_err(mmc_dev(host->mmc), "Unable to configure MMC IRQs\n"); goto err_irq_cd_init; } @@ -1918,7 +1964,7 @@ static int __devinit omap_hsmmc_probe(struct platform_device *pdev) IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT, mmc_hostname(mmc), host); if (ret) { - dev_dbg(mmc_dev(host->mmc), + dev_err(mmc_dev(host->mmc), "Unable to grab MMC CD IRQ\n"); goto err_irq_cd; } @@ -1928,6 +1974,11 @@ static int __devinit omap_hsmmc_probe(struct platform_device *pdev) omap_hsmmc_disable_irq(host); + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (IS_ERR(pinctrl)) + dev_warn(&pdev->dev, + "pins are not configured from the driver\n"); + omap_hsmmc_protect_card(host); mmc_add_host(mmc); @@ -2027,6 +2078,25 @@ static int __devexit omap_hsmmc_remove(struct platform_device *pdev) } #ifdef CONFIG_PM +static int omap_hsmmc_prepare(struct device *dev) +{ + struct omap_hsmmc_host *host = dev_get_drvdata(dev); + + if (host->pdata->suspend) + return host->pdata->suspend(dev, host->slot_id); + + return 0; +} + +static void omap_hsmmc_complete(struct device *dev) +{ + struct omap_hsmmc_host *host = dev_get_drvdata(dev); + + if (host->pdata->resume) + host->pdata->resume(dev, host->slot_id); + +} + static int omap_hsmmc_suspend(struct device *dev) { int ret = 0; @@ -2040,23 +2110,10 @@ static int omap_hsmmc_suspend(struct device *dev) pm_runtime_get_sync(host->dev); host->suspended = 1; - if (host->pdata->suspend) { - ret = host->pdata->suspend(dev, host->slot_id); - if (ret) { - dev_dbg(dev, "Unable to handle MMC board" - " level suspend\n"); - host->suspended = 0; - return ret; - } - } ret = mmc_suspend_host(host->mmc); if (ret) { host->suspended = 0; - if (host->pdata->resume) { - if (host->pdata->resume(dev, host->slot_id)) - dev_dbg(dev, "Unmask interrupt failed\n"); - } goto err; } @@ -2093,12 +2150,6 @@ static int omap_hsmmc_resume(struct device *dev) if (!(host->mmc->pm_flags & MMC_PM_KEEP_POWER)) omap_hsmmc_conf_bus_power(host); - if (host->pdata->resume) { - ret = host->pdata->resume(dev, host->slot_id); - if (ret) - dev_dbg(dev, "Unmask interrupt failed\n"); - } - omap_hsmmc_protect_card(host); /* Notify the core to resume the host */ @@ -2114,8 +2165,10 @@ static int omap_hsmmc_resume(struct device *dev) } #else +#define omap_hsmmc_prepare NULL +#define omap_hsmmc_complete NULL #define omap_hsmmc_suspend NULL -#define omap_hsmmc_resume NULL +#define omap_hsmmc_resume NULL #endif static int omap_hsmmc_runtime_suspend(struct device *dev) @@ -2143,6 +2196,8 @@ static int omap_hsmmc_runtime_resume(struct device *dev) static struct dev_pm_ops omap_hsmmc_dev_pm_ops = { .suspend = omap_hsmmc_suspend, .resume = omap_hsmmc_resume, + .prepare = omap_hsmmc_prepare, + .complete = omap_hsmmc_complete, .runtime_suspend = omap_hsmmc_runtime_suspend, .runtime_resume = omap_hsmmc_runtime_resume, }; diff --git a/drivers/mmc/host/sdhci-dove.c b/drivers/mmc/host/sdhci-dove.c index 8fd50a211037..e6214480bc98 100644 --- a/drivers/mmc/host/sdhci-dove.c +++ b/drivers/mmc/host/sdhci-dove.c @@ -19,20 +19,30 @@ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ -#include <linux/err.h> -#include <linux/io.h> #include <linux/clk.h> #include <linux/err.h> -#include <linux/module.h> +#include <linux/gpio.h> +#include <linux/io.h> #include <linux/mmc/host.h> +#include <linux/module.h> #include <linux/of.h> +#include <linux/of_gpio.h> #include "sdhci-pltfm.h" struct sdhci_dove_priv { struct clk *clk; + int gpio_cd; }; +static irqreturn_t sdhci_dove_carddetect_irq(int irq, void *data) +{ + struct sdhci_host *host = data; + + tasklet_schedule(&host->card_tasklet); + return IRQ_HANDLED; +} + static u16 sdhci_dove_readw(struct sdhci_host *host, int reg) { u16 ret; @@ -50,16 +60,25 @@ static u16 sdhci_dove_readw(struct sdhci_host *host, int reg) static u32 sdhci_dove_readl(struct sdhci_host *host, int reg) { + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + struct sdhci_dove_priv *priv = pltfm_host->priv; u32 ret; + ret = readl(host->ioaddr + reg); + switch (reg) { case SDHCI_CAPABILITIES: - ret = readl(host->ioaddr + reg); /* Mask the support for 3.0V */ ret &= ~SDHCI_CAN_VDD_300; break; - default: - ret = readl(host->ioaddr + reg); + case SDHCI_PRESENT_STATE: + if (gpio_is_valid(priv->gpio_cd)) { + if (gpio_get_value(priv->gpio_cd) == 0) + ret |= SDHCI_CARD_PRESENT; + else + ret &= ~SDHCI_CARD_PRESENT; + } + break; } return ret; } @@ -92,25 +111,70 @@ static int __devinit sdhci_dove_probe(struct platform_device *pdev) return -ENOMEM; } - priv->clk = clk_get(&pdev->dev, NULL); - if (!IS_ERR(priv->clk)) - clk_prepare_enable(priv->clk); + priv->clk = devm_clk_get(&pdev->dev, NULL); - ret = sdhci_pltfm_register(pdev, &sdhci_dove_pdata); - if (ret) - goto sdhci_dove_register_fail; + if (pdev->dev.of_node) { + priv->gpio_cd = of_get_named_gpio(pdev->dev.of_node, + "cd-gpios", 0); + } else { + priv->gpio_cd = -EINVAL; + } + + if (gpio_is_valid(priv->gpio_cd)) { + ret = gpio_request(priv->gpio_cd, "sdhci-cd"); + if (ret) { + dev_err(&pdev->dev, "card detect gpio request failed: %d\n", + ret); + return ret; + } + gpio_direction_input(priv->gpio_cd); + } + + host = sdhci_pltfm_init(pdev, &sdhci_dove_pdata); + if (IS_ERR(host)) { + ret = PTR_ERR(host); + goto err_sdhci_pltfm_init; + } - host = platform_get_drvdata(pdev); pltfm_host = sdhci_priv(host); pltfm_host->priv = priv; + if (!IS_ERR(priv->clk)) + clk_prepare_enable(priv->clk); + + sdhci_get_of_property(pdev); + + ret = sdhci_add_host(host); + if (ret) + goto err_sdhci_add; + + /* + * We must request the IRQ after sdhci_add_host(), as the tasklet only + * gets setup in sdhci_add_host() and we oops. + */ + if (gpio_is_valid(priv->gpio_cd)) { + ret = request_irq(gpio_to_irq(priv->gpio_cd), + sdhci_dove_carddetect_irq, + IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, + mmc_hostname(host->mmc), host); + if (ret) { + dev_err(&pdev->dev, "card detect irq request failed: %d\n", + ret); + goto err_request_irq; + } + } + return 0; -sdhci_dove_register_fail: - if (!IS_ERR(priv->clk)) { +err_request_irq: + sdhci_remove_host(host, 0); +err_sdhci_add: + if (!IS_ERR(priv->clk)) clk_disable_unprepare(priv->clk); - clk_put(priv->clk); - } + sdhci_pltfm_free(pdev); +err_sdhci_pltfm_init: + if (gpio_is_valid(priv->gpio_cd)) + gpio_free(priv->gpio_cd); return ret; } @@ -122,10 +186,14 @@ static int __devexit sdhci_dove_remove(struct platform_device *pdev) sdhci_pltfm_unregister(pdev); - if (!IS_ERR(priv->clk)) { - clk_disable_unprepare(priv->clk); - clk_put(priv->clk); + if (gpio_is_valid(priv->gpio_cd)) { + free_irq(gpio_to_irq(priv->gpio_cd), host); + gpio_free(priv->gpio_cd); } + + if (!IS_ERR(priv->clk)) + clk_disable_unprepare(priv->clk); + return 0; } diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c index effc2acfe778..1849461c39ee 100644 --- a/drivers/mmc/host/sdhci-esdhc-imx.c +++ b/drivers/mmc/host/sdhci-esdhc-imx.c @@ -456,10 +456,10 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) pltfm_host = sdhci_priv(host); - imx_data = kzalloc(sizeof(struct pltfm_imx_data), GFP_KERNEL); + imx_data = devm_kzalloc(&pdev->dev, sizeof(*imx_data), GFP_KERNEL); if (!imx_data) { err = -ENOMEM; - goto err_imx_data; + goto free_sdhci; } if (of_id) @@ -470,19 +470,19 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg"); if (IS_ERR(imx_data->clk_ipg)) { err = PTR_ERR(imx_data->clk_ipg); - goto err_clk_get; + goto free_sdhci; } imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb"); if (IS_ERR(imx_data->clk_ahb)) { err = PTR_ERR(imx_data->clk_ahb); - goto err_clk_get; + goto free_sdhci; } imx_data->clk_per = devm_clk_get(&pdev->dev, "per"); if (IS_ERR(imx_data->clk_per)) { err = PTR_ERR(imx_data->clk_per); - goto err_clk_get; + goto free_sdhci; } pltfm_host->clk = imx_data->clk_per; @@ -494,7 +494,7 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) imx_data->pinctrl = devm_pinctrl_get_select_default(&pdev->dev); if (IS_ERR(imx_data->pinctrl)) { err = PTR_ERR(imx_data->pinctrl); - goto pin_err; + goto disable_clk; } host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL; @@ -519,7 +519,7 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) if (!host->mmc->parent->platform_data) { dev_err(mmc_dev(host->mmc), "no board data!\n"); err = -EINVAL; - goto no_board_data; + goto disable_clk; } imx_data->boarddata = *((struct esdhc_platform_data *) host->mmc->parent->platform_data); @@ -527,7 +527,8 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) /* write_protect */ if (boarddata->wp_type == ESDHC_WP_GPIO) { - err = gpio_request_one(boarddata->wp_gpio, GPIOF_IN, "ESDHC_WP"); + err = devm_gpio_request_one(&pdev->dev, boarddata->wp_gpio, + GPIOF_IN, "ESDHC_WP"); if (err) { dev_warn(mmc_dev(host->mmc), "no write-protect pin available!\n"); @@ -543,19 +544,21 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) switch (boarddata->cd_type) { case ESDHC_CD_GPIO: - err = gpio_request_one(boarddata->cd_gpio, GPIOF_IN, "ESDHC_CD"); + err = devm_gpio_request_one(&pdev->dev, boarddata->cd_gpio, + GPIOF_IN, "ESDHC_CD"); if (err) { dev_err(mmc_dev(host->mmc), "no card-detect pin available!\n"); - goto no_card_detect_pin; + goto disable_clk; } - err = request_irq(gpio_to_irq(boarddata->cd_gpio), cd_irq, + err = devm_request_irq(&pdev->dev, + gpio_to_irq(boarddata->cd_gpio), cd_irq, IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING, mmc_hostname(host->mmc), host); if (err) { dev_err(mmc_dev(host->mmc), "request irq error\n"); - goto no_card_detect_irq; + goto disable_clk; } /* fall through */ @@ -574,27 +577,15 @@ static int __devinit sdhci_esdhc_imx_probe(struct platform_device *pdev) err = sdhci_add_host(host); if (err) - goto err_add_host; + goto disable_clk; return 0; -err_add_host: - if (gpio_is_valid(boarddata->cd_gpio)) - free_irq(gpio_to_irq(boarddata->cd_gpio), host); -no_card_detect_irq: - if (gpio_is_valid(boarddata->cd_gpio)) - gpio_free(boarddata->cd_gpio); - if (gpio_is_valid(boarddata->wp_gpio)) - gpio_free(boarddata->wp_gpio); -no_card_detect_pin: -no_board_data: -pin_err: +disable_clk: clk_disable_unprepare(imx_data->clk_per); clk_disable_unprepare(imx_data->clk_ipg); clk_disable_unprepare(imx_data->clk_ahb); -err_clk_get: - kfree(imx_data); -err_imx_data: +free_sdhci: sdhci_pltfm_free(pdev); return err; } @@ -604,25 +595,14 @@ static int __devexit sdhci_esdhc_imx_remove(struct platform_device *pdev) struct sdhci_host *host = platform_get_drvdata(pdev); struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); struct pltfm_imx_data *imx_data = pltfm_host->priv; - struct esdhc_platform_data *boarddata = &imx_data->boarddata; int dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff); sdhci_remove_host(host, dead); - if (gpio_is_valid(boarddata->wp_gpio)) - gpio_free(boarddata->wp_gpio); - - if (gpio_is_valid(boarddata->cd_gpio)) { - free_irq(gpio_to_irq(boarddata->cd_gpio), host); - gpio_free(boarddata->cd_gpio); - } - clk_disable_unprepare(imx_data->clk_per); clk_disable_unprepare(imx_data->clk_ipg); clk_disable_unprepare(imx_data->clk_ahb); - kfree(imx_data); - sdhci_pltfm_free(pdev); return 0; diff --git a/drivers/mmc/host/sdhci-of-esdhc.c b/drivers/mmc/host/sdhci-of-esdhc.c index 63d219f57cae..60de2eeb39b1 100644 --- a/drivers/mmc/host/sdhci-of-esdhc.c +++ b/drivers/mmc/host/sdhci-of-esdhc.c @@ -22,6 +22,7 @@ #include "sdhci-esdhc.h" #define VENDOR_V_22 0x12 +#define VENDOR_V_23 0x13 static u32 esdhc_readl(struct sdhci_host *host, int reg) { u32 ret; @@ -85,6 +86,18 @@ static u8 esdhc_readb(struct sdhci_host *host, int reg) return ret; } +static void esdhc_writel(struct sdhci_host *host, u32 val, int reg) +{ + /* + * Enable IRQSTATEN[BGESEN] is just to set IRQSTAT[BGE] + * when SYSCTL[RSTD]) is set for some special operations. + * No any impact other operation. + */ + if (reg == SDHCI_INT_ENABLE) + val |= SDHCI_INT_BLK_GAP; + sdhci_be32bs_writel(host, val, reg); +} + static void esdhc_writew(struct sdhci_host *host, u16 val, int reg) { if (reg == SDHCI_BLOCK_SIZE) { @@ -121,6 +134,41 @@ static void esdhc_writeb(struct sdhci_host *host, u8 val, int reg) sdhci_be32bs_writeb(host, val, reg); } +/* + * For Abort or Suspend after Stop at Block Gap, ignore the ADMA + * error(IRQSTAT[ADMAE]) if both Transfer Complete(IRQSTAT[TC]) + * and Block Gap Event(IRQSTAT[BGE]) are also set. + * For Continue, apply soft reset for data(SYSCTL[RSTD]); + * and re-issue the entire read transaction from beginning. + */ +static void esdhci_of_adma_workaround(struct sdhci_host *host, u32 intmask) +{ + u32 tmp; + bool applicable; + dma_addr_t dmastart; + dma_addr_t dmanow; + + tmp = in_be32(host->ioaddr + SDHCI_SLOT_INT_STATUS); + tmp = (tmp & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT; + + applicable = (intmask & SDHCI_INT_DATA_END) && + (intmask & SDHCI_INT_BLK_GAP) && + (tmp == VENDOR_V_23); + if (!applicable) + return; + + host->data->error = 0; + dmastart = sg_dma_address(host->data->sg); + dmanow = dmastart + host->data->bytes_xfered; + /* + * Force update to the next DMA block boundary. + */ + dmanow = (dmanow & ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) + + SDHCI_DEFAULT_BOUNDARY_SIZE; + host->data->bytes_xfered = dmanow - dmastart; + sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS); +} + static int esdhc_of_enable_dma(struct sdhci_host *host) { setbits32(host->ioaddr + ESDHC_DMA_SYSCTL, ESDHC_DMA_SNOOP); @@ -177,13 +225,16 @@ static void esdhc_of_platform_init(struct sdhci_host *host) vvn = (vvn & SDHCI_VENDOR_VER_MASK) >> SDHCI_VENDOR_VER_SHIFT; if (vvn == VENDOR_V_22) host->quirks2 |= SDHCI_QUIRK2_HOST_NO_CMD23; + + if (vvn > VENDOR_V_22) + host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ; } static struct sdhci_ops sdhci_esdhc_ops = { .read_l = esdhc_readl, .read_w = esdhc_readw, .read_b = esdhc_readb, - .write_l = sdhci_be32bs_writel, + .write_l = esdhc_writel, .write_w = esdhc_writew, .write_b = esdhc_writeb, .set_clock = esdhc_of_set_clock, @@ -195,6 +246,7 @@ static struct sdhci_ops sdhci_esdhc_ops = { .platform_suspend = esdhc_of_suspend, .platform_resume = esdhc_of_resume, #endif + .adma_workaround = esdhci_of_adma_workaround, }; static struct sdhci_pltfm_data sdhci_esdhc_pdata = { diff --git a/drivers/mmc/host/sdhci-pci.c b/drivers/mmc/host/sdhci-pci.c index 04936f353ced..0777fad997ba 100644 --- a/drivers/mmc/host/sdhci-pci.c +++ b/drivers/mmc/host/sdhci-pci.c @@ -114,6 +114,7 @@ static int ricoh_mmc_probe_slot(struct sdhci_pci_slot *slot) SDHCI_TIMEOUT_CLK_UNIT | SDHCI_CAN_VDD_330 | + SDHCI_CAN_DO_HISPD | SDHCI_CAN_DO_SDMA; return 0; } diff --git a/drivers/mmc/host/sdhci-pltfm.c b/drivers/mmc/host/sdhci-pltfm.c index 27164457f861..d4283ef5917a 100644 --- a/drivers/mmc/host/sdhci-pltfm.c +++ b/drivers/mmc/host/sdhci-pltfm.c @@ -78,6 +78,9 @@ void sdhci_get_of_property(struct platform_device *pdev) if (of_get_property(np, "broken-cd", NULL)) host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION; + if (of_get_property(np, "no-1-8-v", NULL)) + host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V; + if (of_device_is_compatible(np, "fsl,p2020-rev1-esdhc")) host->quirks |= SDHCI_QUIRK_BROKEN_DMA; @@ -89,6 +92,12 @@ void sdhci_get_of_property(struct platform_device *pdev) clk = of_get_property(np, "clock-frequency", &size); if (clk && size == sizeof(*clk) && *clk) pltfm_host->clock = be32_to_cpup(clk); + + if (of_find_property(np, "keep-power-in-suspend", NULL)) + host->mmc->pm_caps |= MMC_PM_KEEP_POWER; + + if (of_find_property(np, "enable-sdio-wakeup", NULL)) + host->mmc->pm_caps |= MMC_PM_WAKE_SDIO_IRQ; } } #else diff --git a/drivers/mmc/host/sdhci-pxav3.c b/drivers/mmc/host/sdhci-pxav3.c index e918a2bb3af1..60829c92bcfd 100644 --- a/drivers/mmc/host/sdhci-pxav3.c +++ b/drivers/mmc/host/sdhci-pxav3.c @@ -163,10 +163,18 @@ static int pxav3_set_uhs_signaling(struct sdhci_host *host, unsigned int uhs) return 0; } +static u32 pxav3_get_max_clock(struct sdhci_host *host) +{ + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); + + return clk_get_rate(pltfm_host->clk); +} + static struct sdhci_ops pxav3_sdhci_ops = { .platform_reset_exit = pxav3_set_private_registers, .set_uhs_signaling = pxav3_set_uhs_signaling, .platform_send_init_74_clocks = pxav3_gen_init_74_clocks, + .get_max_clock = pxav3_get_max_clock, }; #ifdef CONFIG_OF @@ -249,7 +257,8 @@ static int __devinit sdhci_pxav3_probe(struct platform_device *pdev) host->quirks = SDHCI_QUIRK_BROKEN_TIMEOUT_VAL | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC - | SDHCI_QUIRK_32BIT_ADMA_SIZE; + | SDHCI_QUIRK_32BIT_ADMA_SIZE + | SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN; /* enable 1/8V DDR capable */ host->mmc->caps |= MMC_CAP_1_8V_DDR; @@ -271,6 +280,8 @@ static int __devinit sdhci_pxav3_probe(struct platform_device *pdev) if (pdata->quirks) host->quirks |= pdata->quirks; + if (pdata->quirks2) + host->quirks2 |= pdata->quirks2; if (pdata->host_caps) host->mmc->caps |= pdata->host_caps; if (pdata->host_caps2) diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c index c9ec725884e5..82b7a7ad4217 100644 --- a/drivers/mmc/host/sdhci-s3c.c +++ b/drivers/mmc/host/sdhci-s3c.c @@ -24,6 +24,7 @@ #include <linux/of_gpio.h> #include <linux/pm.h> #include <linux/pm_runtime.h> +#include <linux/pinctrl/consumer.h> #include <linux/mmc/host.h> @@ -57,6 +58,7 @@ struct sdhci_s3c { int ext_cd_irq; int ext_cd_gpio; int *gpios; + struct pinctrl *pctrl; struct clk *clk_io; struct clk *clk_bus[MAX_BUS_CLK]; @@ -373,7 +375,9 @@ static struct sdhci_ops sdhci_s3c_ops = { static void sdhci_s3c_notify_change(struct platform_device *dev, int state) { struct sdhci_host *host = platform_get_drvdata(dev); +#ifdef CONFIG_PM_RUNTIME struct sdhci_s3c *sc = sdhci_priv(host); +#endif unsigned long flags; if (host) { @@ -413,7 +417,7 @@ static void sdhci_s3c_setup_card_detect_gpio(struct sdhci_s3c *sc) struct s3c_sdhci_platdata *pdata = sc->pdata; struct device *dev = &sc->pdev->dev; - if (gpio_request(pdata->ext_cd_gpio, "SDHCI EXT CD") == 0) { + if (devm_gpio_request(dev, pdata->ext_cd_gpio, "SDHCI EXT CD") == 0) { sc->ext_cd_gpio = pdata->ext_cd_gpio; sc->ext_cd_irq = gpio_to_irq(pdata->ext_cd_gpio); if (sc->ext_cd_irq && @@ -456,12 +460,12 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev, return -ENOMEM; /* get the card detection method */ - if (of_get_property(node, "broken-cd", 0)) { + if (of_get_property(node, "broken-cd", NULL)) { pdata->cd_type = S3C_SDHCI_CD_NONE; goto setup_bus; } - if (of_get_property(node, "non-removable", 0)) { + if (of_get_property(node, "non-removable", NULL)) { pdata->cd_type = S3C_SDHCI_CD_PERMANENT; goto setup_bus; } @@ -484,8 +488,9 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev, return -EINVAL; } - dev_info(dev, "assuming no card detect line available\n"); - pdata->cd_type = S3C_SDHCI_CD_NONE; + /* assuming internal card detect that will be configured by pinctrl */ + pdata->cd_type = S3C_SDHCI_CD_INTERNAL; + goto setup_bus; found_cd: if (pdata->cd_type == S3C_SDHCI_CD_GPIO) { @@ -494,7 +499,7 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev, if (of_get_property(node, "cd-inverted", NULL)) pdata->ext_cd_gpio_invert = 1; } else if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL) { - ret = gpio_request(gpio, "sdhci-cd"); + ret = devm_gpio_request(dev, gpio, "sdhci-cd"); if (ret) { dev_err(dev, "card detect gpio request failed\n"); return -EINVAL; @@ -503,33 +508,28 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev, } setup_bus: + if (!IS_ERR(ourhost->pctrl)) + return 0; + /* get the gpios for command, clock and data lines */ for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) { gpio = of_get_gpio(node, cnt); if (!gpio_is_valid(gpio)) { dev_err(dev, "invalid gpio[%d]\n", cnt); - goto err_free_dt_cd_gpio; + return -EINVAL; } ourhost->gpios[cnt] = gpio; } for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) { - ret = gpio_request(ourhost->gpios[cnt], "sdhci-gpio"); + ret = devm_gpio_request(dev, ourhost->gpios[cnt], "sdhci-gpio"); if (ret) { dev_err(dev, "gpio[%d] request failed\n", cnt); - goto err_free_dt_gpios; + return -EINVAL; } } return 0; - - err_free_dt_gpios: - while (--cnt >= 0) - gpio_free(ourhost->gpios[cnt]); - err_free_dt_cd_gpio: - if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL) - gpio_free(ourhost->ext_cd_gpio); - return -EINVAL; } #else static int __devinit sdhci_s3c_parse_dt(struct device *dev, @@ -586,13 +586,15 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev) pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) { ret = -ENOMEM; - goto err_pdata; + goto err_pdata_io_clk; } + sc->pctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (pdev->dev.of_node) { ret = sdhci_s3c_parse_dt(&pdev->dev, host, pdata); if (ret) - goto err_pdata; + goto err_pdata_io_clk; } else { memcpy(pdata, pdev->dev.platform_data, sizeof(*pdata)); sc->ext_cd_gpio = -1; /* invalid gpio number */ @@ -610,7 +612,7 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev) if (IS_ERR(sc->clk_io)) { dev_err(dev, "failed to get io clock\n"); ret = PTR_ERR(sc->clk_io); - goto err_io_clk; + goto err_pdata_io_clk; } /* enable the local io clock and keep it running for the moment. */ @@ -773,13 +775,7 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev) clk_disable_unprepare(sc->clk_io); clk_put(sc->clk_io); - err_io_clk: - for (ptr = 0; ptr < NUM_GPIOS(sc->pdata->max_width); ptr++) - gpio_free(sc->gpios[ptr]); - if (pdata->cd_type == S3C_SDHCI_CD_INTERNAL) - gpio_free(sc->ext_cd_gpio); - - err_pdata: + err_pdata_io_clk: sdhci_free_host(host); return ret; @@ -798,9 +794,6 @@ static int __devexit sdhci_s3c_remove(struct platform_device *pdev) if (sc->ext_cd_irq) free_irq(sc->ext_cd_irq, sc); - if (gpio_is_valid(sc->ext_cd_gpio)) - gpio_free(sc->ext_cd_gpio); - #ifdef CONFIG_PM_RUNTIME if (pdata->cd_type != S3C_SDHCI_CD_INTERNAL) clk_prepare_enable(sc->clk_io); @@ -821,11 +814,6 @@ static int __devexit sdhci_s3c_remove(struct platform_device *pdev) clk_disable_unprepare(sc->clk_io); clk_put(sc->clk_io); - if (pdev->dev.of_node) { - for (ptr = 0; ptr < NUM_GPIOS(sc->pdata->max_width); ptr++) - gpio_free(sc->gpios[ptr]); - } - sdhci_free_host(host); platform_set_drvdata(pdev, NULL); diff --git a/drivers/mmc/host/sdhci-spear.c b/drivers/mmc/host/sdhci-spear.c index 6be89c032deb..87a700944b7d 100644 --- a/drivers/mmc/host/sdhci-spear.c +++ b/drivers/mmc/host/sdhci-spear.c @@ -146,6 +146,11 @@ static int __devinit sdhci_probe(struct platform_device *pdev) goto put_clk; } + ret = clk_set_rate(sdhci->clk, 50000000); + if (ret) + dev_dbg(&pdev->dev, "Error setting desired clk, clk=%lu\n", + clk_get_rate(sdhci->clk)); + if (np) { sdhci->data = sdhci_probe_config_dt(pdev); if (IS_ERR(sdhci->data)) { @@ -297,7 +302,7 @@ static int sdhci_suspend(struct device *dev) ret = sdhci_suspend_host(host); if (!ret) - clk_disable_unprepare(sdhci->clk); + clk_disable(sdhci->clk); return ret; } @@ -308,7 +313,7 @@ static int sdhci_resume(struct device *dev) struct spear_sdhci *sdhci = dev_get_platdata(dev); int ret; - ret = clk_prepare_enable(sdhci->clk); + ret = clk_enable(sdhci->clk); if (ret) { dev_dbg(dev, "Resume: Error enabling clock\n"); return ret; diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c index c7851c0aabce..6f0bfc0c8c9c 100644 --- a/drivers/mmc/host/sdhci.c +++ b/drivers/mmc/host/sdhci.c @@ -1618,7 +1618,7 @@ static int sdhci_do_3_3v_signal_voltage_switch(struct sdhci_host *host, sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2); if (host->vqmmc) { - ret = regulator_set_voltage(host->vqmmc, 3300000, 3300000); + ret = regulator_set_voltage(host->vqmmc, 2700000, 3600000); if (ret) { pr_warning("%s: Switching to 3.3V signalling voltage " " failed\n", mmc_hostname(host->mmc)); @@ -1662,7 +1662,7 @@ static int sdhci_do_1_8v_signal_voltage_switch(struct sdhci_host *host, */ if (host->vqmmc) ret = regulator_set_voltage(host->vqmmc, - 1800000, 1800000); + 1700000, 1950000); else ret = 0; @@ -1994,30 +1994,11 @@ static void sdhci_enable_preset_value(struct mmc_host *mmc, bool enable) sdhci_runtime_pm_put(host); } -static const struct mmc_host_ops sdhci_ops = { - .request = sdhci_request, - .set_ios = sdhci_set_ios, - .get_ro = sdhci_get_ro, - .hw_reset = sdhci_hw_reset, - .enable_sdio_irq = sdhci_enable_sdio_irq, - .start_signal_voltage_switch = sdhci_start_signal_voltage_switch, - .execute_tuning = sdhci_execute_tuning, - .enable_preset_value = sdhci_enable_preset_value, -}; - -/*****************************************************************************\ - * * - * Tasklets * - * * -\*****************************************************************************/ - -static void sdhci_tasklet_card(unsigned long param) +static void sdhci_card_event(struct mmc_host *mmc) { - struct sdhci_host *host; + struct sdhci_host *host = mmc_priv(mmc); unsigned long flags; - host = (struct sdhci_host*)param; - spin_lock_irqsave(&host->lock, flags); /* Check host->mrq first in case we are runtime suspended */ @@ -2036,6 +2017,31 @@ static void sdhci_tasklet_card(unsigned long param) } spin_unlock_irqrestore(&host->lock, flags); +} + +static const struct mmc_host_ops sdhci_ops = { + .request = sdhci_request, + .set_ios = sdhci_set_ios, + .get_ro = sdhci_get_ro, + .hw_reset = sdhci_hw_reset, + .enable_sdio_irq = sdhci_enable_sdio_irq, + .start_signal_voltage_switch = sdhci_start_signal_voltage_switch, + .execute_tuning = sdhci_execute_tuning, + .enable_preset_value = sdhci_enable_preset_value, + .card_event = sdhci_card_event, +}; + +/*****************************************************************************\ + * * + * Tasklets * + * * +\*****************************************************************************/ + +static void sdhci_tasklet_card(unsigned long param) +{ + struct sdhci_host *host = (struct sdhci_host*)param; + + sdhci_card_event(host->mmc); mmc_detect_change(host->mmc, msecs_to_jiffies(200)); } @@ -2282,6 +2288,8 @@ static void sdhci_data_irq(struct sdhci_host *host, u32 intmask) pr_err("%s: ADMA error\n", mmc_hostname(host->mmc)); sdhci_show_adma_error(host); host->data->error = -EIO; + if (host->ops->adma_workaround) + host->ops->adma_workaround(host, intmask); } if (host->data->error) @@ -2858,10 +2866,16 @@ int sdhci_add_host(struct sdhci_host *host) mmc_hostname(mmc)); host->vqmmc = NULL; } - } - else if (regulator_is_supported_voltage(host->vqmmc, 1800000, 1800000)) + } else { regulator_enable(host->vqmmc); - else + if (!regulator_is_supported_voltage(host->vqmmc, 1700000, + 1950000)) + caps[1] &= ~(SDHCI_SUPPORT_SDR104 | + SDHCI_SUPPORT_SDR50 | + SDHCI_SUPPORT_DDR50); + } + + if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) caps[1] &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50); @@ -2919,21 +2933,18 @@ int sdhci_add_host(struct sdhci_host *host) mmc_hostname(mmc)); host->vmmc = NULL; } - } else - regulator_enable(host->vmmc); + } #ifdef CONFIG_REGULATOR if (host->vmmc) { - ret = regulator_is_supported_voltage(host->vmmc, 3300000, - 3300000); + ret = regulator_is_supported_voltage(host->vmmc, 2700000, + 3600000); if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_330))) caps[0] &= ~SDHCI_CAN_VDD_330; - ret = regulator_is_supported_voltage(host->vmmc, 3000000, - 3000000); if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_300))) caps[0] &= ~SDHCI_CAN_VDD_300; - ret = regulator_is_supported_voltage(host->vmmc, 1800000, - 1800000); + ret = regulator_is_supported_voltage(host->vmmc, 1700000, + 1950000); if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_180))) caps[0] &= ~SDHCI_CAN_VDD_180; } diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h index 71a4a7ed46c5..a6d69b7bdea2 100644 --- a/drivers/mmc/host/sdhci.h +++ b/drivers/mmc/host/sdhci.h @@ -120,6 +120,7 @@ #define SDHCI_SIGNAL_ENABLE 0x38 #define SDHCI_INT_RESPONSE 0x00000001 #define SDHCI_INT_DATA_END 0x00000002 +#define SDHCI_INT_BLK_GAP 0x00000004 #define SDHCI_INT_DMA_END 0x00000008 #define SDHCI_INT_SPACE_AVAIL 0x00000010 #define SDHCI_INT_DATA_AVAIL 0x00000020 @@ -146,7 +147,8 @@ #define SDHCI_INT_DATA_MASK (SDHCI_INT_DATA_END | SDHCI_INT_DMA_END | \ SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL | \ SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_DATA_CRC | \ - SDHCI_INT_DATA_END_BIT | SDHCI_INT_ADMA_ERROR) + SDHCI_INT_DATA_END_BIT | SDHCI_INT_ADMA_ERROR | \ + SDHCI_INT_BLK_GAP) #define SDHCI_INT_ALL_MASK ((unsigned int)-1) #define SDHCI_ACMD12_ERR 0x3C @@ -278,6 +280,7 @@ struct sdhci_ops { void (*hw_reset)(struct sdhci_host *host); void (*platform_suspend)(struct sdhci_host *host); void (*platform_resume)(struct sdhci_host *host); + void (*adma_workaround)(struct sdhci_host *host, u32 intmask); void (*platform_init)(struct sdhci_host *host); }; diff --git a/drivers/mmc/host/sh_mmcif.c b/drivers/mmc/host/sh_mmcif.c index 7eaee3eeb6b2..ae795233a1d6 100644 --- a/drivers/mmc/host/sh_mmcif.c +++ b/drivers/mmc/host/sh_mmcif.c @@ -1306,7 +1306,6 @@ static int __devinit sh_mmcif_probe(struct platform_device *pdev) struct sh_mmcif_plat_data *pd = pdev->dev.platform_data; struct resource *res; void __iomem *reg; - char clk_name[8]; irq[0] = platform_get_irq(pdev, 0); irq[1] = platform_get_irq(pdev, 1); @@ -1356,11 +1355,10 @@ static int __devinit sh_mmcif_probe(struct platform_device *pdev) pm_runtime_enable(&pdev->dev); host->power = false; - snprintf(clk_name, sizeof(clk_name), "mmc%d", pdev->id); - host->hclk = clk_get(&pdev->dev, clk_name); + host->hclk = clk_get(&pdev->dev, NULL); if (IS_ERR(host->hclk)) { ret = PTR_ERR(host->hclk); - dev_err(&pdev->dev, "cannot get clock \"%s\": %d\n", clk_name, ret); + dev_err(&pdev->dev, "cannot get clock: %d\n", ret); goto eclkget; } ret = sh_mmcif_clk_update(host); diff --git a/drivers/mmc/host/sh_mobile_sdhi.c b/drivers/mmc/host/sh_mobile_sdhi.c index 0bdc146178db..d6ff8531fb35 100644 --- a/drivers/mmc/host/sh_mobile_sdhi.c +++ b/drivers/mmc/host/sh_mobile_sdhi.c @@ -123,7 +123,6 @@ static int __devinit sh_mobile_sdhi_probe(struct platform_device *pdev) struct tmio_mmc_data *mmc_data; struct sh_mobile_sdhi_info *p = pdev->dev.platform_data; struct tmio_mmc_host *host; - char clk_name[8]; int irq, ret, i = 0; bool multiplexed_isr = true; @@ -144,11 +143,10 @@ static int __devinit sh_mobile_sdhi_probe(struct platform_device *pdev) } } - snprintf(clk_name, sizeof(clk_name), "sdhi%d", pdev->id); - priv->clk = clk_get(&pdev->dev, clk_name); + priv->clk = clk_get(&pdev->dev, NULL); if (IS_ERR(priv->clk)) { - dev_err(&pdev->dev, "cannot get clock \"%s\"\n", clk_name); ret = PTR_ERR(priv->clk); + dev_err(&pdev->dev, "cannot get clock: %d\n", ret); goto eclkget; } @@ -250,7 +248,7 @@ static int __devinit sh_mobile_sdhi_probe(struct platform_device *pdev) dev_info(&pdev->dev, "%s base at 0x%08lx clock rate %u MHz\n", mmc_hostname(host->mmc), (unsigned long) (platform_get_resource(pdev, IORESOURCE_MEM, 0)->start), - mmc_data->hclk / 1000000); + host->mmc->f_max / 1000000); return ret; diff --git a/drivers/mmc/host/vub300.c b/drivers/mmc/host/vub300.c index d5655a63eda4..cb9f361c03ab 100644 --- a/drivers/mmc/host/vub300.c +++ b/drivers/mmc/host/vub300.c @@ -2362,6 +2362,7 @@ error4: error1: usb_free_urb(command_out_urb); error0: + usb_put_dev(udev); return retval; } diff --git a/drivers/mmc/host/wmt-sdmmc.c b/drivers/mmc/host/wmt-sdmmc.c new file mode 100644 index 000000000000..5ba4605e4f80 --- /dev/null +++ b/drivers/mmc/host/wmt-sdmmc.c @@ -0,0 +1,1029 @@ +/* + * WM8505/WM8650 SD/MMC Host Controller + * + * Copyright (C) 2010 Tony Prisk + * Copyright (C) 2008 WonderMedia Technologies, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation + */ + +#include <linux/init.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/ioport.h> +#include <linux/errno.h> +#include <linux/dma-mapping.h> +#include <linux/delay.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/clk.h> +#include <linux/gpio.h> + +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_irq.h> +#include <linux/of_device.h> + +#include <linux/mmc/host.h> +#include <linux/mmc/mmc.h> +#include <linux/mmc/sd.h> + +#include <asm/byteorder.h> + + +#define DRIVER_NAME "wmt-sdhc" + + +/* MMC/SD controller registers */ +#define SDMMC_CTLR 0x00 +#define SDMMC_CMD 0x01 +#define SDMMC_RSPTYPE 0x02 +#define SDMMC_ARG 0x04 +#define SDMMC_BUSMODE 0x08 +#define SDMMC_BLKLEN 0x0C +#define SDMMC_BLKCNT 0x0E +#define SDMMC_RSP 0x10 +#define SDMMC_CBCR 0x20 +#define SDMMC_INTMASK0 0x24 +#define SDMMC_INTMASK1 0x25 +#define SDMMC_STS0 0x28 +#define SDMMC_STS1 0x29 +#define SDMMC_STS2 0x2A +#define SDMMC_STS3 0x2B +#define SDMMC_RSPTIMEOUT 0x2C +#define SDMMC_CLK 0x30 /* VT8500 only */ +#define SDMMC_EXTCTRL 0x34 +#define SDMMC_SBLKLEN 0x38 +#define SDMMC_DMATIMEOUT 0x3C + + +/* SDMMC_CTLR bit fields */ +#define CTLR_CMD_START 0x01 +#define CTLR_CMD_WRITE 0x04 +#define CTLR_FIFO_RESET 0x08 + +/* SDMMC_BUSMODE bit fields */ +#define BM_SPI_MODE 0x01 +#define BM_FOURBIT_MODE 0x02 +#define BM_EIGHTBIT_MODE 0x04 +#define BM_SD_OFF 0x10 +#define BM_SPI_CS 0x20 +#define BM_SD_POWER 0x40 +#define BM_SOFT_RESET 0x80 +#define BM_ONEBIT_MASK 0xFD + +/* SDMMC_BLKLEN bit fields */ +#define BLKL_CRCERR_ABORT 0x0800 +#define BLKL_CD_POL_HIGH 0x1000 +#define BLKL_GPI_CD 0x2000 +#define BLKL_DATA3_CD 0x4000 +#define BLKL_INT_ENABLE 0x8000 + +/* SDMMC_INTMASK0 bit fields */ +#define INT0_MBLK_TRAN_DONE_INT_EN 0x10 +#define INT0_BLK_TRAN_DONE_INT_EN 0x20 +#define INT0_CD_INT_EN 0x40 +#define INT0_DI_INT_EN 0x80 + +/* SDMMC_INTMASK1 bit fields */ +#define INT1_CMD_RES_TRAN_DONE_INT_EN 0x02 +#define INT1_CMD_RES_TOUT_INT_EN 0x04 +#define INT1_MBLK_AUTO_STOP_INT_EN 0x08 +#define INT1_DATA_TOUT_INT_EN 0x10 +#define INT1_RESCRC_ERR_INT_EN 0x20 +#define INT1_RCRC_ERR_INT_EN 0x40 +#define INT1_WCRC_ERR_INT_EN 0x80 + +/* SDMMC_STS0 bit fields */ +#define STS0_WRITE_PROTECT 0x02 +#define STS0_CD_DATA3 0x04 +#define STS0_CD_GPI 0x08 +#define STS0_MBLK_DONE 0x10 +#define STS0_BLK_DONE 0x20 +#define STS0_CARD_DETECT 0x40 +#define STS0_DEVICE_INS 0x80 + +/* SDMMC_STS1 bit fields */ +#define STS1_SDIO_INT 0x01 +#define STS1_CMDRSP_DONE 0x02 +#define STS1_RSP_TIMEOUT 0x04 +#define STS1_AUTOSTOP_DONE 0x08 +#define STS1_DATA_TIMEOUT 0x10 +#define STS1_RSP_CRC_ERR 0x20 +#define STS1_RCRC_ERR 0x40 +#define STS1_WCRC_ERR 0x80 + +/* SDMMC_STS2 bit fields */ +#define STS2_CMD_RES_BUSY 0x10 +#define STS2_DATARSP_BUSY 0x20 +#define STS2_DIS_FORCECLK 0x80 + + +/* MMC/SD DMA Controller Registers */ +#define SDDMA_GCR 0x100 +#define SDDMA_IER 0x104 +#define SDDMA_ISR 0x108 +#define SDDMA_DESPR 0x10C +#define SDDMA_RBR 0x110 +#define SDDMA_DAR 0x114 +#define SDDMA_BAR 0x118 +#define SDDMA_CPR 0x11C +#define SDDMA_CCR 0x120 + + +/* SDDMA_GCR bit fields */ +#define DMA_GCR_DMA_EN 0x00000001 +#define DMA_GCR_SOFT_RESET 0x00000100 + +/* SDDMA_IER bit fields */ +#define DMA_IER_INT_EN 0x00000001 + +/* SDDMA_ISR bit fields */ +#define DMA_ISR_INT_STS 0x00000001 + +/* SDDMA_RBR bit fields */ +#define DMA_RBR_FORMAT 0x40000000 +#define DMA_RBR_END 0x80000000 + +/* SDDMA_CCR bit fields */ +#define DMA_CCR_RUN 0x00000080 +#define DMA_CCR_IF_TO_PERIPHERAL 0x00000000 +#define DMA_CCR_PERIPHERAL_TO_IF 0x00400000 + +/* SDDMA_CCR event status */ +#define DMA_CCR_EVT_NO_STATUS 0x00000000 +#define DMA_CCR_EVT_UNDERRUN 0x00000001 +#define DMA_CCR_EVT_OVERRUN 0x00000002 +#define DMA_CCR_EVT_DESP_READ 0x00000003 +#define DMA_CCR_EVT_DATA_RW 0x00000004 +#define DMA_CCR_EVT_EARLY_END 0x00000005 +#define DMA_CCR_EVT_SUCCESS 0x0000000F + +#define PDMA_READ 0x00 +#define PDMA_WRITE 0x01 + +#define WMT_SD_POWER_OFF 0 +#define WMT_SD_POWER_ON 1 + +struct wmt_dma_descriptor { + u32 flags; + u32 data_buffer_addr; + u32 branch_addr; + u32 reserved1; +}; + +struct wmt_mci_caps { + unsigned int f_min; + unsigned int f_max; + u32 ocr_avail; + u32 caps; + u32 max_seg_size; + u32 max_segs; + u32 max_blk_size; +}; + +struct wmt_mci_priv { + struct mmc_host *mmc; + void __iomem *sdmmc_base; + + int irq_regular; + int irq_dma; + + void *dma_desc_buffer; + dma_addr_t dma_desc_device_addr; + + struct completion cmdcomp; + struct completion datacomp; + + struct completion *comp_cmd; + struct completion *comp_dma; + + struct mmc_request *req; + struct mmc_command *cmd; + + struct clk *clk_sdmmc; + struct device *dev; + + u8 power_inverted; + u8 cd_inverted; +}; + +static void wmt_set_sd_power(struct wmt_mci_priv *priv, int enable) +{ + u32 reg_tmp; + if (enable) { + if (priv->power_inverted) { + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp | BM_SD_OFF, + priv->sdmmc_base + SDMMC_BUSMODE); + } else { + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp & (~BM_SD_OFF), + priv->sdmmc_base + SDMMC_BUSMODE); + } + } else { + if (priv->power_inverted) { + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp & (~BM_SD_OFF), + priv->sdmmc_base + SDMMC_BUSMODE); + } else { + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp | BM_SD_OFF, + priv->sdmmc_base + SDMMC_BUSMODE); + } + } +} + +static void wmt_mci_read_response(struct mmc_host *mmc) +{ + struct wmt_mci_priv *priv; + int idx1, idx2; + u8 tmp_resp; + u32 response; + + priv = mmc_priv(mmc); + + for (idx1 = 0; idx1 < 4; idx1++) { + response = 0; + for (idx2 = 0; idx2 < 4; idx2++) { + if ((idx1 == 3) && (idx2 == 3)) + tmp_resp = readb(priv->sdmmc_base + SDMMC_RSP); + else + tmp_resp = readb(priv->sdmmc_base + SDMMC_RSP + + (idx1*4) + idx2 + 1); + response |= (tmp_resp << (idx2 * 8)); + } + priv->cmd->resp[idx1] = cpu_to_be32(response); + } +} + +static void wmt_mci_start_command(struct wmt_mci_priv *priv) +{ + u32 reg_tmp; + + reg_tmp = readb(priv->sdmmc_base + SDMMC_CTLR); + writeb(reg_tmp | CTLR_CMD_START, priv->sdmmc_base + SDMMC_CTLR); +} + +static int wmt_mci_send_command(struct mmc_host *mmc, u8 command, u8 cmdtype, + u32 arg, u8 rsptype) +{ + struct wmt_mci_priv *priv; + u32 reg_tmp; + + priv = mmc_priv(mmc); + + /* write command, arg, resptype registers */ + writeb(command, priv->sdmmc_base + SDMMC_CMD); + writel(arg, priv->sdmmc_base + SDMMC_ARG); + writeb(rsptype, priv->sdmmc_base + SDMMC_RSPTYPE); + + /* reset response FIFO */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_CTLR); + writeb(reg_tmp | CTLR_FIFO_RESET, priv->sdmmc_base + SDMMC_CTLR); + + /* ensure clock enabled - VT3465 */ + wmt_set_sd_power(priv, WMT_SD_POWER_ON); + + /* clear status bits */ + writeb(0xFF, priv->sdmmc_base + SDMMC_STS0); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS1); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS2); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS3); + + /* set command type */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_CTLR); + writeb((reg_tmp & 0x0F) | (cmdtype << 4), + priv->sdmmc_base + SDMMC_CTLR); + + return 0; +} + +static void wmt_mci_disable_dma(struct wmt_mci_priv *priv) +{ + writel(DMA_ISR_INT_STS, priv->sdmmc_base + SDDMA_ISR); + writel(0, priv->sdmmc_base + SDDMA_IER); +} + +static void wmt_complete_data_request(struct wmt_mci_priv *priv) +{ + struct mmc_request *req; + req = priv->req; + + req->data->bytes_xfered = req->data->blksz * req->data->blocks; + + /* unmap the DMA pages used for write data */ + if (req->data->flags & MMC_DATA_WRITE) + dma_unmap_sg(mmc_dev(priv->mmc), req->data->sg, + req->data->sg_len, DMA_TO_DEVICE); + else + dma_unmap_sg(mmc_dev(priv->mmc), req->data->sg, + req->data->sg_len, DMA_FROM_DEVICE); + + /* Check if the DMA ISR returned a data error */ + if ((req->cmd->error) || (req->data->error)) + mmc_request_done(priv->mmc, req); + else { + wmt_mci_read_response(priv->mmc); + if (!req->data->stop) { + /* single-block read/write requests end here */ + mmc_request_done(priv->mmc, req); + } else { + /* + * we change the priv->cmd variable so the response is + * stored in the stop struct rather than the original + * calling command struct + */ + priv->comp_cmd = &priv->cmdcomp; + init_completion(priv->comp_cmd); + priv->cmd = req->data->stop; + wmt_mci_send_command(priv->mmc, req->data->stop->opcode, + 7, req->data->stop->arg, 9); + wmt_mci_start_command(priv); + } + } +} + +static irqreturn_t wmt_mci_dma_isr(int irq_num, void *data) +{ + struct mmc_host *mmc; + struct wmt_mci_priv *priv; + + int status; + + priv = (struct wmt_mci_priv *)data; + mmc = priv->mmc; + + status = readl(priv->sdmmc_base + SDDMA_CCR) & 0x0F; + + if (status != DMA_CCR_EVT_SUCCESS) { + dev_err(priv->dev, "DMA Error: Status = %d\n", status); + priv->req->data->error = -ETIMEDOUT; + complete(priv->comp_dma); + return IRQ_HANDLED; + } + + priv->req->data->error = 0; + + wmt_mci_disable_dma(priv); + + complete(priv->comp_dma); + + if (priv->comp_cmd) { + if (completion_done(priv->comp_cmd)) { + /* + * if the command (regular) interrupt has already + * completed, finish off the request otherwise we wait + * for the command interrupt and finish from there. + */ + wmt_complete_data_request(priv); + } + } + + return IRQ_HANDLED; +} + +static irqreturn_t wmt_mci_regular_isr(int irq_num, void *data) +{ + struct wmt_mci_priv *priv; + u32 status0; + u32 status1; + u32 status2; + u32 reg_tmp; + int cmd_done; + + priv = (struct wmt_mci_priv *)data; + cmd_done = 0; + status0 = readb(priv->sdmmc_base + SDMMC_STS0); + status1 = readb(priv->sdmmc_base + SDMMC_STS1); + status2 = readb(priv->sdmmc_base + SDMMC_STS2); + + /* Check for card insertion */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_INTMASK0); + if ((reg_tmp & INT0_DI_INT_EN) && (status0 & STS0_DEVICE_INS)) { + mmc_detect_change(priv->mmc, 0); + if (priv->cmd) + priv->cmd->error = -ETIMEDOUT; + if (priv->comp_cmd) + complete(priv->comp_cmd); + if (priv->comp_dma) { + wmt_mci_disable_dma(priv); + complete(priv->comp_dma); + } + writeb(STS0_DEVICE_INS, priv->sdmmc_base + SDMMC_STS0); + return IRQ_HANDLED; + } + + if ((!priv->req->data) || + ((priv->req->data->stop) && (priv->cmd == priv->req->data->stop))) { + /* handle non-data & stop_transmission requests */ + if (status1 & STS1_CMDRSP_DONE) { + priv->cmd->error = 0; + cmd_done = 1; + } else if ((status1 & STS1_RSP_TIMEOUT) || + (status1 & STS1_DATA_TIMEOUT)) { + priv->cmd->error = -ETIMEDOUT; + cmd_done = 1; + } + + if (cmd_done) { + priv->comp_cmd = NULL; + + if (!priv->cmd->error) + wmt_mci_read_response(priv->mmc); + + priv->cmd = NULL; + + mmc_request_done(priv->mmc, priv->req); + } + } else { + /* handle data requests */ + if (status1 & STS1_CMDRSP_DONE) { + if (priv->cmd) + priv->cmd->error = 0; + if (priv->comp_cmd) + complete(priv->comp_cmd); + } + + if ((status1 & STS1_RSP_TIMEOUT) || + (status1 & STS1_DATA_TIMEOUT)) { + if (priv->cmd) + priv->cmd->error = -ETIMEDOUT; + if (priv->comp_cmd) + complete(priv->comp_cmd); + if (priv->comp_dma) { + wmt_mci_disable_dma(priv); + complete(priv->comp_dma); + } + } + + if (priv->comp_dma) { + /* + * If the dma interrupt has already completed, finish + * off the request; otherwise we wait for the DMA + * interrupt and finish from there. + */ + if (completion_done(priv->comp_dma)) + wmt_complete_data_request(priv); + } + } + + writeb(status0, priv->sdmmc_base + SDMMC_STS0); + writeb(status1, priv->sdmmc_base + SDMMC_STS1); + writeb(status2, priv->sdmmc_base + SDMMC_STS2); + + return IRQ_HANDLED; +} + +static void wmt_reset_hardware(struct mmc_host *mmc) +{ + struct wmt_mci_priv *priv; + u32 reg_tmp; + + priv = mmc_priv(mmc); + + /* reset controller */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp | BM_SOFT_RESET, priv->sdmmc_base + SDMMC_BUSMODE); + + /* reset response FIFO */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_CTLR); + writeb(reg_tmp | CTLR_FIFO_RESET, priv->sdmmc_base + SDMMC_CTLR); + + /* enable GPI pin to detect card */ + writew(BLKL_INT_ENABLE | BLKL_GPI_CD, priv->sdmmc_base + SDMMC_BLKLEN); + + /* clear interrupt status */ + writeb(0xFF, priv->sdmmc_base + SDMMC_STS0); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS1); + + /* setup interrupts */ + writeb(INT0_CD_INT_EN | INT0_DI_INT_EN, priv->sdmmc_base + + SDMMC_INTMASK0); + writeb(INT1_DATA_TOUT_INT_EN | INT1_CMD_RES_TRAN_DONE_INT_EN | + INT1_CMD_RES_TOUT_INT_EN, priv->sdmmc_base + SDMMC_INTMASK1); + + /* set the DMA timeout */ + writew(8191, priv->sdmmc_base + SDMMC_DMATIMEOUT); + + /* auto clock freezing enable */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_STS2); + writeb(reg_tmp | STS2_DIS_FORCECLK, priv->sdmmc_base + SDMMC_STS2); + + /* set a default clock speed of 400Khz */ + clk_set_rate(priv->clk_sdmmc, 400000); +} + +static int wmt_dma_init(struct mmc_host *mmc) +{ + struct wmt_mci_priv *priv; + + priv = mmc_priv(mmc); + + writel(DMA_GCR_SOFT_RESET, priv->sdmmc_base + SDDMA_GCR); + writel(DMA_GCR_DMA_EN, priv->sdmmc_base + SDDMA_GCR); + if ((readl(priv->sdmmc_base + SDDMA_GCR) & DMA_GCR_DMA_EN) != 0) + return 0; + else + return 1; +} + +static void wmt_dma_init_descriptor(struct wmt_dma_descriptor *desc, + u16 req_count, u32 buffer_addr, u32 branch_addr, int end) +{ + desc->flags = 0x40000000 | req_count; + if (end) + desc->flags |= 0x80000000; + desc->data_buffer_addr = buffer_addr; + desc->branch_addr = branch_addr; +} + +static void wmt_dma_config(struct mmc_host *mmc, u32 descaddr, u8 dir) +{ + struct wmt_mci_priv *priv; + u32 reg_tmp; + + priv = mmc_priv(mmc); + + /* Enable DMA Interrupts */ + writel(DMA_IER_INT_EN, priv->sdmmc_base + SDDMA_IER); + + /* Write DMA Descriptor Pointer Register */ + writel(descaddr, priv->sdmmc_base + SDDMA_DESPR); + + writel(0x00, priv->sdmmc_base + SDDMA_CCR); + + if (dir == PDMA_WRITE) { + reg_tmp = readl(priv->sdmmc_base + SDDMA_CCR); + writel(reg_tmp & DMA_CCR_IF_TO_PERIPHERAL, priv->sdmmc_base + + SDDMA_CCR); + } else { + reg_tmp = readl(priv->sdmmc_base + SDDMA_CCR); + writel(reg_tmp | DMA_CCR_PERIPHERAL_TO_IF, priv->sdmmc_base + + SDDMA_CCR); + } +} + +static void wmt_dma_start(struct wmt_mci_priv *priv) +{ + u32 reg_tmp; + + reg_tmp = readl(priv->sdmmc_base + SDDMA_CCR); + writel(reg_tmp | DMA_CCR_RUN, priv->sdmmc_base + SDDMA_CCR); +} + +static void wmt_mci_request(struct mmc_host *mmc, struct mmc_request *req) +{ + struct wmt_mci_priv *priv; + struct wmt_dma_descriptor *desc; + u8 command; + u8 cmdtype; + u32 arg; + u8 rsptype; + u32 reg_tmp; + + struct scatterlist *sg; + int i; + int sg_cnt; + int offset; + u32 dma_address; + int desc_cnt; + + priv = mmc_priv(mmc); + priv->req = req; + + /* + * Use the cmd variable to pass a pointer to the resp[] structure + * This is required on multi-block requests to pass the pointer to the + * stop command + */ + priv->cmd = req->cmd; + + command = req->cmd->opcode; + arg = req->cmd->arg; + rsptype = mmc_resp_type(req->cmd); + cmdtype = 0; + + /* rsptype=7 only valid for SPI commands - should be =2 for SD */ + if (rsptype == 7) + rsptype = 2; + /* rsptype=21 is R1B, convert for controller */ + if (rsptype == 21) + rsptype = 9; + + if (!req->data) { + wmt_mci_send_command(mmc, command, cmdtype, arg, rsptype); + wmt_mci_start_command(priv); + /* completion is now handled in the regular_isr() */ + } + if (req->data) { + priv->comp_cmd = &priv->cmdcomp; + init_completion(priv->comp_cmd); + + wmt_dma_init(mmc); + + /* set controller data length */ + reg_tmp = readw(priv->sdmmc_base + SDMMC_BLKLEN); + writew((reg_tmp & 0xF800) | (req->data->blksz - 1), + priv->sdmmc_base + SDMMC_BLKLEN); + + /* set controller block count */ + writew(req->data->blocks, priv->sdmmc_base + SDMMC_BLKCNT); + + desc = (struct wmt_dma_descriptor *)priv->dma_desc_buffer; + + if (req->data->flags & MMC_DATA_WRITE) { + sg_cnt = dma_map_sg(mmc_dev(mmc), req->data->sg, + req->data->sg_len, DMA_TO_DEVICE); + cmdtype = 1; + if (req->data->blocks > 1) + cmdtype = 3; + } else { + sg_cnt = dma_map_sg(mmc_dev(mmc), req->data->sg, + req->data->sg_len, DMA_FROM_DEVICE); + cmdtype = 2; + if (req->data->blocks > 1) + cmdtype = 4; + } + + dma_address = priv->dma_desc_device_addr + 16; + desc_cnt = 0; + + for_each_sg(req->data->sg, sg, sg_cnt, i) { + offset = 0; + while (offset < sg_dma_len(sg)) { + wmt_dma_init_descriptor(desc, req->data->blksz, + sg_dma_address(sg)+offset, + dma_address, 0); + desc++; + desc_cnt++; + offset += req->data->blksz; + dma_address += 16; + if (desc_cnt == req->data->blocks) + break; + } + } + desc--; + desc->flags |= 0x80000000; + + if (req->data->flags & MMC_DATA_WRITE) + wmt_dma_config(mmc, priv->dma_desc_device_addr, + PDMA_WRITE); + else + wmt_dma_config(mmc, priv->dma_desc_device_addr, + PDMA_READ); + + wmt_mci_send_command(mmc, command, cmdtype, arg, rsptype); + + priv->comp_dma = &priv->datacomp; + init_completion(priv->comp_dma); + + wmt_dma_start(priv); + wmt_mci_start_command(priv); + } +} + +static void wmt_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + struct wmt_mci_priv *priv; + u32 reg_tmp; + + priv = mmc_priv(mmc); + + if (ios->power_mode == MMC_POWER_UP) { + wmt_reset_hardware(mmc); + + wmt_set_sd_power(priv, WMT_SD_POWER_ON); + } + if (ios->power_mode == MMC_POWER_OFF) + wmt_set_sd_power(priv, WMT_SD_POWER_OFF); + + if (ios->clock != 0) + clk_set_rate(priv->clk_sdmmc, ios->clock); + + switch (ios->bus_width) { + case MMC_BUS_WIDTH_8: + reg_tmp = readb(priv->sdmmc_base + SDMMC_EXTCTRL); + writeb(reg_tmp | 0x04, priv->sdmmc_base + SDMMC_EXTCTRL); + break; + case MMC_BUS_WIDTH_4: + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp | BM_FOURBIT_MODE, priv->sdmmc_base + + SDMMC_BUSMODE); + + reg_tmp = readb(priv->sdmmc_base + SDMMC_EXTCTRL); + writeb(reg_tmp & 0xFB, priv->sdmmc_base + SDMMC_EXTCTRL); + break; + case MMC_BUS_WIDTH_1: + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp & BM_ONEBIT_MASK, priv->sdmmc_base + + SDMMC_BUSMODE); + + reg_tmp = readb(priv->sdmmc_base + SDMMC_EXTCTRL); + writeb(reg_tmp & 0xFB, priv->sdmmc_base + SDMMC_EXTCTRL); + break; + } +} + +static int wmt_mci_get_ro(struct mmc_host *mmc) +{ + struct wmt_mci_priv *priv = mmc_priv(mmc); + + return !(readb(priv->sdmmc_base + SDMMC_STS0) & STS0_WRITE_PROTECT); +} + +static int wmt_mci_get_cd(struct mmc_host *mmc) +{ + struct wmt_mci_priv *priv = mmc_priv(mmc); + u32 cd = (readb(priv->sdmmc_base + SDMMC_STS0) & STS0_CD_GPI) >> 3; + + return !(cd ^ priv->cd_inverted); +} + +static struct mmc_host_ops wmt_mci_ops = { + .request = wmt_mci_request, + .set_ios = wmt_mci_set_ios, + .get_ro = wmt_mci_get_ro, + .get_cd = wmt_mci_get_cd, +}; + +/* Controller capabilities */ +static struct wmt_mci_caps wm8505_caps = { + .f_min = 390425, + .f_max = 50000000, + .ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34, + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MMC_HIGHSPEED | + MMC_CAP_SD_HIGHSPEED, + .max_seg_size = 65024, + .max_segs = 128, + .max_blk_size = 2048, +}; + +static struct of_device_id wmt_mci_dt_ids[] = { + { .compatible = "wm,wm8505-sdhc", .data = &wm8505_caps }, + { /* Sentinel */ }, +}; + +static int __devinit wmt_mci_probe(struct platform_device *pdev) +{ + struct mmc_host *mmc; + struct wmt_mci_priv *priv; + struct device_node *np = pdev->dev.of_node; + const struct of_device_id *of_id = + of_match_device(wmt_mci_dt_ids, &pdev->dev); + const struct wmt_mci_caps *wmt_caps = of_id->data; + int ret; + int regular_irq, dma_irq; + + if (!of_id || !of_id->data) { + dev_err(&pdev->dev, "Controller capabilities data missing\n"); + return -EFAULT; + } + + if (!np) { + dev_err(&pdev->dev, "Missing SDMMC description in devicetree\n"); + return -EFAULT; + } + + regular_irq = irq_of_parse_and_map(np, 0); + dma_irq = irq_of_parse_and_map(np, 1); + + if (!regular_irq || !dma_irq) { + dev_err(&pdev->dev, "Getting IRQs failed!\n"); + ret = -ENXIO; + goto fail1; + } + + mmc = mmc_alloc_host(sizeof(struct wmt_mci_priv), &pdev->dev); + if (!mmc) { + dev_err(&pdev->dev, "Failed to allocate mmc_host\n"); + ret = -ENOMEM; + goto fail1; + } + + mmc->ops = &wmt_mci_ops; + mmc->f_min = wmt_caps->f_min; + mmc->f_max = wmt_caps->f_max; + mmc->ocr_avail = wmt_caps->ocr_avail; + mmc->caps = wmt_caps->caps; + + mmc->max_seg_size = wmt_caps->max_seg_size; + mmc->max_segs = wmt_caps->max_segs; + mmc->max_blk_size = wmt_caps->max_blk_size; + + mmc->max_req_size = (16*512*mmc->max_segs); + mmc->max_blk_count = mmc->max_req_size / 512; + + priv = mmc_priv(mmc); + priv->mmc = mmc; + priv->dev = &pdev->dev; + + priv->power_inverted = 0; + priv->cd_inverted = 0; + + if (of_get_property(np, "sdon-inverted", NULL)) + priv->power_inverted = 1; + if (of_get_property(np, "cd-inverted", NULL)) + priv->cd_inverted = 1; + + priv->sdmmc_base = of_iomap(np, 0); + if (!priv->sdmmc_base) { + dev_err(&pdev->dev, "Failed to map IO space\n"); + ret = -ENOMEM; + goto fail2; + } + + priv->irq_regular = regular_irq; + priv->irq_dma = dma_irq; + + ret = request_irq(regular_irq, wmt_mci_regular_isr, 0, "sdmmc", priv); + if (ret) { + dev_err(&pdev->dev, "Register regular IRQ fail\n"); + goto fail3; + } + + ret = request_irq(dma_irq, wmt_mci_dma_isr, 32, "sdmmc", priv); + if (ret) { + dev_err(&pdev->dev, "Register DMA IRQ fail\n"); + goto fail4; + } + + /* alloc some DMA buffers for descriptors/transfers */ + priv->dma_desc_buffer = dma_alloc_coherent(&pdev->dev, + mmc->max_blk_count * 16, + &priv->dma_desc_device_addr, + 208); + if (!priv->dma_desc_buffer) { + dev_err(&pdev->dev, "DMA alloc fail\n"); + ret = -EPERM; + goto fail5; + } + + platform_set_drvdata(pdev, mmc); + + priv->clk_sdmmc = of_clk_get(np, 0); + if (IS_ERR(priv->clk_sdmmc)) { + dev_err(&pdev->dev, "Error getting clock\n"); + ret = PTR_ERR(priv->clk_sdmmc); + goto fail5; + } + + clk_prepare_enable(priv->clk_sdmmc); + + /* configure the controller to a known 'ready' state */ + wmt_reset_hardware(mmc); + + mmc_add_host(mmc); + + dev_info(&pdev->dev, "WMT SDHC Controller initialized\n"); + + return 0; +fail5: + free_irq(dma_irq, priv); +fail4: + free_irq(regular_irq, priv); +fail3: + iounmap(priv->sdmmc_base); +fail2: + mmc_free_host(mmc); +fail1: + return ret; +} + +static int __devexit wmt_mci_remove(struct platform_device *pdev) +{ + struct mmc_host *mmc; + struct wmt_mci_priv *priv; + struct resource *res; + u32 reg_tmp; + + mmc = platform_get_drvdata(pdev); + priv = mmc_priv(mmc); + + /* reset SD controller */ + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writel(reg_tmp | BM_SOFT_RESET, priv->sdmmc_base + SDMMC_BUSMODE); + reg_tmp = readw(priv->sdmmc_base + SDMMC_BLKLEN); + writew(reg_tmp & ~(0xA000), priv->sdmmc_base + SDMMC_BLKLEN); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS0); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS1); + + /* release the dma buffers */ + dma_free_coherent(&pdev->dev, priv->mmc->max_blk_count * 16, + priv->dma_desc_buffer, priv->dma_desc_device_addr); + + mmc_remove_host(mmc); + + free_irq(priv->irq_regular, priv); + free_irq(priv->irq_dma, priv); + + iounmap(priv->sdmmc_base); + + clk_disable_unprepare(priv->clk_sdmmc); + clk_put(priv->clk_sdmmc); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(res->start, res->end - res->start + 1); + + mmc_free_host(mmc); + + platform_set_drvdata(pdev, NULL); + + dev_info(&pdev->dev, "WMT MCI device removed\n"); + + return 0; +} + +#ifdef CONFIG_PM +static int wmt_mci_suspend(struct device *dev) +{ + u32 reg_tmp; + struct platform_device *pdev = to_platform_device(dev); + struct mmc_host *mmc = platform_get_drvdata(pdev); + struct wmt_mci_priv *priv; + int ret; + + if (!mmc) + return 0; + + priv = mmc_priv(mmc); + ret = mmc_suspend_host(mmc); + + if (!ret) { + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp | BM_SOFT_RESET, priv->sdmmc_base + + SDMMC_BUSMODE); + + reg_tmp = readw(priv->sdmmc_base + SDMMC_BLKLEN); + writew(reg_tmp & 0x5FFF, priv->sdmmc_base + SDMMC_BLKLEN); + + writeb(0xFF, priv->sdmmc_base + SDMMC_STS0); + writeb(0xFF, priv->sdmmc_base + SDMMC_STS1); + + clk_disable(priv->clk_sdmmc); + } + return ret; +} + +static int wmt_mci_resume(struct device *dev) +{ + u32 reg_tmp; + struct platform_device *pdev = to_platform_device(dev); + struct mmc_host *mmc = platform_get_drvdata(pdev); + struct wmt_mci_priv *priv; + int ret = 0; + + if (mmc) { + priv = mmc_priv(mmc); + clk_enable(priv->clk_sdmmc); + + reg_tmp = readb(priv->sdmmc_base + SDMMC_BUSMODE); + writeb(reg_tmp | BM_SOFT_RESET, priv->sdmmc_base + + SDMMC_BUSMODE); + + reg_tmp = readw(priv->sdmmc_base + SDMMC_BLKLEN); + writew(reg_tmp | (BLKL_GPI_CD | BLKL_INT_ENABLE), + priv->sdmmc_base + SDMMC_BLKLEN); + + reg_tmp = readb(priv->sdmmc_base + SDMMC_INTMASK0); + writeb(reg_tmp | INT0_DI_INT_EN, priv->sdmmc_base + + SDMMC_INTMASK0); + + ret = mmc_resume_host(mmc); + } + + return ret; +} + +static const struct dev_pm_ops wmt_mci_pm = { + .suspend = wmt_mci_suspend, + .resume = wmt_mci_resume, +}; + +#define wmt_mci_pm_ops (&wmt_mci_pm) + +#else /* !CONFIG_PM */ + +#define wmt_mci_pm_ops NULL + +#endif + +static struct platform_driver wmt_mci_driver = { + .probe = wmt_mci_probe, + .remove = __exit_p(wmt_mci_remove), + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + .pm = wmt_mci_pm_ops, + .of_match_table = wmt_mci_dt_ids, + }, +}; + +module_platform_driver(wmt_mci_driver); + +MODULE_DESCRIPTION("Wondermedia MMC/SD Driver"); +MODULE_AUTHOR("Tony Prisk"); +MODULE_LICENSE("GPL v2"); +MODULE_DEVICE_TABLE(of, wmt_mci_dt_ids); diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h index 943550dfe9ea..5c69315d60cc 100644 --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -85,6 +85,7 @@ struct mmc_ext_csd { bool boot_ro_lockable; u8 raw_exception_status; /* 53 */ u8 raw_partition_support; /* 160 */ + u8 raw_rpmb_size_mult; /* 168 */ u8 raw_erased_mem_count; /* 181 */ u8 raw_ext_csd_structure; /* 194 */ u8 raw_card_type; /* 196 */ @@ -206,6 +207,7 @@ struct mmc_part { #define MMC_BLK_DATA_AREA_MAIN (1<<0) #define MMC_BLK_DATA_AREA_BOOT (1<<1) #define MMC_BLK_DATA_AREA_GP (1<<2) +#define MMC_BLK_DATA_AREA_RPMB (1<<3) }; /* diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h index 9b9cdafc7737..5bf7c2274fcb 100644 --- a/include/linux/mmc/core.h +++ b/include/linux/mmc/core.h @@ -170,6 +170,8 @@ extern int mmc_erase_group_aligned(struct mmc_card *card, unsigned int from, extern unsigned int mmc_calc_max_discard(struct mmc_card *card); extern int mmc_set_blocklen(struct mmc_card *card, unsigned int blocklen); +extern int mmc_set_blockcount(struct mmc_card *card, unsigned int blockcount, + bool is_rel_write); extern int mmc_hw_reset(struct mmc_host *host); extern int mmc_hw_reset_check(struct mmc_host *host); extern int mmc_can_reset(struct mmc_card *card); diff --git a/include/linux/mmc/dw_mmc.h b/include/linux/mmc/dw_mmc.h index 96531664a061..34be4f47293c 100644 --- a/include/linux/mmc/dw_mmc.h +++ b/include/linux/mmc/dw_mmc.h @@ -229,8 +229,9 @@ struct dw_mci_board { u32 quirks; /* Workaround / Quirk flags */ unsigned int bus_hz; /* Clock speed at the cclk_in pad */ - unsigned int caps; /* Capabilities */ - unsigned int caps2; /* More capabilities */ + u32 caps; /* Capabilities */ + u32 caps2; /* More capabilities */ + u32 pm_caps; /* PM capabilities */ /* * Override fifo depth. If 0, autodetect it from the FIFOTH register, * but note that this may not be reliable after a bootloader has used diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h index 7abb0e1f7bda..61a10c17aabd 100644 --- a/include/linux/mmc/host.h +++ b/include/linux/mmc/host.h @@ -53,12 +53,12 @@ struct mmc_ios { #define MMC_TIMING_LEGACY 0 #define MMC_TIMING_MMC_HS 1 #define MMC_TIMING_SD_HS 2 -#define MMC_TIMING_UHS_SDR12 MMC_TIMING_LEGACY -#define MMC_TIMING_UHS_SDR25 MMC_TIMING_SD_HS -#define MMC_TIMING_UHS_SDR50 3 -#define MMC_TIMING_UHS_SDR104 4 -#define MMC_TIMING_UHS_DDR50 5 -#define MMC_TIMING_MMC_HS200 6 +#define MMC_TIMING_UHS_SDR12 3 +#define MMC_TIMING_UHS_SDR25 4 +#define MMC_TIMING_UHS_SDR50 5 +#define MMC_TIMING_UHS_SDR104 6 +#define MMC_TIMING_UHS_DDR50 7 +#define MMC_TIMING_MMC_HS200 8 #define MMC_SDR_MODE 0 #define MMC_1_2V_DDR_MODE 1 @@ -136,6 +136,7 @@ struct mmc_host_ops { void (*enable_preset_value)(struct mmc_host *host, bool enable); int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv); void (*hw_reset)(struct mmc_host *host); + void (*card_event)(struct mmc_host *host); }; struct mmc_card; @@ -211,7 +212,7 @@ struct mmc_host { #define MMC_VDD_34_35 0x00400000 /* VDD voltage 3.4 ~ 3.5 */ #define MMC_VDD_35_36 0x00800000 /* VDD voltage 3.5 ~ 3.6 */ - unsigned long caps; /* Host capabilities */ + u32 caps; /* Host capabilities */ #define MMC_CAP_4_BIT_DATA (1 << 0) /* Can the host do 4 bit transfers */ #define MMC_CAP_MMC_HIGHSPEED (1 << 1) /* Can do MMC high-speed timing */ @@ -241,7 +242,7 @@ struct mmc_host { #define MMC_CAP_CMD23 (1 << 30) /* CMD23 supported. */ #define MMC_CAP_HW_RESET (1 << 31) /* Hardware reset */ - unsigned int caps2; /* More host capabilities */ + u32 caps2; /* More host capabilities */ #define MMC_CAP2_BOOTPART_NOACC (1 << 0) /* Boot partition no access */ #define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */ diff --git a/include/linux/mmc/mmc.h b/include/linux/mmc/mmc.h index 01e4b394029b..94d532e41c61 100644 --- a/include/linux/mmc/mmc.h +++ b/include/linux/mmc/mmc.h @@ -286,6 +286,7 @@ struct _mmc_csd { #define EXT_CSD_BKOPS_START 164 /* W */ #define EXT_CSD_SANITIZE_START 165 /* W */ #define EXT_CSD_WR_REL_PARAM 166 /* RO */ +#define EXT_CSD_RPMB_MULT 168 /* RO */ #define EXT_CSD_BOOT_WP 173 /* R/W */ #define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */ #define EXT_CSD_PART_CONFIG 179 /* R/W */ @@ -339,6 +340,7 @@ struct _mmc_csd { #define EXT_CSD_PART_CONFIG_ACC_MASK (0x7) #define EXT_CSD_PART_CONFIG_ACC_BOOT0 (0x1) +#define EXT_CSD_PART_CONFIG_ACC_RPMB (0x3) #define EXT_CSD_PART_CONFIG_ACC_GP0 (0x4) #define EXT_CSD_PART_SUPPORT_PART_EN (0x1) diff --git a/include/linux/mmc/mxs-mmc.h b/include/linux/mmc/mxs-mmc.h deleted file mode 100644 index 7c2ad3a7f2f3..000000000000 --- a/include/linux/mmc/mxs-mmc.h +++ /dev/null @@ -1,19 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License version 2 as - * published by the Free Software Foundation. - */ - -#ifndef __LINUX_MMC_MXS_MMC_H__ -#define __LINUX_MMC_MXS_MMC_H__ - -struct mxs_mmc_platform_data { - int wp_gpio; /* write protect pin */ - unsigned int flags; -#define SLOTF_4_BIT_CAPABLE (1 << 0) -#define SLOTF_8_BIT_CAPABLE (1 << 1) -}; - -#endif /* __LINUX_MMC_MXS_MMC_H__ */ diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h index 1edcb4dad8c4..4bbc3301fbbf 100644 --- a/include/linux/mmc/sdhci.h +++ b/include/linux/mmc/sdhci.h @@ -92,6 +92,8 @@ struct sdhci_host { #define SDHCI_QUIRK2_HOST_OFF_CARD_ON (1<<0) #define SDHCI_QUIRK2_HOST_NO_CMD23 (1<<1) +/* The system physically doesn't support 1.8v, even if the host does */ +#define SDHCI_QUIRK2_NO_1_8_V (1<<2) int irq; /* Device IRQ */ void __iomem *ioaddr; /* Mapped address */ @@ -158,8 +160,8 @@ struct sdhci_host { struct timer_list timer; /* Timer for timeouts */ - unsigned int caps; /* Alternative CAPABILITY_0 */ - unsigned int caps1; /* Alternative CAPABILITY_1 */ + u32 caps; /* Alternative CAPABILITY_0 */ + u32 caps1; /* Alternative CAPABILITY_1 */ unsigned int ocr_avail_sdio; /* OCR bit masks */ unsigned int ocr_avail_sd; diff --git a/include/linux/platform_data/pxa_sdhci.h b/include/linux/platform_data/pxa_sdhci.h index 59acd987ed34..27d3156d093a 100644 --- a/include/linux/platform_data/pxa_sdhci.h +++ b/include/linux/platform_data/pxa_sdhci.h @@ -38,6 +38,7 @@ * @max_speed: the maximum speed supported * @host_caps: Standard MMC host capabilities bit field. * @quirks: quirks of platfrom + * @quirks2: quirks2 of platfrom * @pm_caps: pm_caps of platfrom */ struct sdhci_pxa_platdata { @@ -48,9 +49,10 @@ struct sdhci_pxa_platdata { unsigned int ext_cd_gpio; bool ext_cd_gpio_invert; unsigned int max_speed; - unsigned int host_caps; - unsigned int host_caps2; + u32 host_caps; + u32 host_caps2; unsigned int quirks; + unsigned int quirks2; unsigned int pm_caps; }; |