diff options
| -rw-r--r-- | arch/arm/boot/dts/omap2.dtsi | 2 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-n8x0.c | 6 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3beagle.c | 28 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/omap_phy_internal.c | 6 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/usb-musb.c | 6 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/usb-tusb6010.c | 2 |
6 files changed, 19 insertions, 31 deletions
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi index f2ab4ea7cc0e..581cb081cb0f 100644 --- a/arch/arm/boot/dts/omap2.dtsi +++ b/arch/arm/boot/dts/omap2.dtsi @@ -44,6 +44,8 @@ compatible = "ti,omap2-intc"; interrupt-controller; #interrupt-cells = <1>; + ti,intc-size = <96>; + reg = <0x480FE000 0x1000>; }; uart1: serial@4806a000 { diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c index 8ca14e88a31a..2c5d0ed75285 100644 --- a/arch/arm/mach-omap2/board-n8x0.c +++ b/arch/arm/mach-omap2/board-n8x0.c @@ -83,11 +83,9 @@ static struct musb_hdrc_config musb_config = { }; static struct musb_hdrc_platform_data tusb_data = { -#if defined(CONFIG_USB_MUSB_OTG) +#ifdef CONFIG_USB_GADGET_MUSB_HDRC .mode = MUSB_OTG, -#elif defined(CONFIG_USB_MUSB_PERIPHERAL) - .mode = MUSB_PERIPHERAL, -#else /* defined(CONFIG_USB_MUSB_HOST) */ +#else .mode = MUSB_HOST, #endif .set_power = tusb_set_power, diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 79c6909eeb78..580fd17208da 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -81,13 +81,13 @@ static u8 omap3_beagle_version; static struct { int mmc1_gpio_wp; int usb_pwr_level; - int reset_gpio; + int dvi_pd_gpio; int usr_button_gpio; int mmc_caps; } beagle_config = { .mmc1_gpio_wp = -EINVAL, .usb_pwr_level = GPIOF_OUT_INIT_LOW, - .reset_gpio = 129, + .dvi_pd_gpio = -EINVAL, .usr_button_gpio = 4, .mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA, }; @@ -126,21 +126,21 @@ static void __init omap3_beagle_init_rev(void) printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX; beagle_config.mmc1_gpio_wp = 29; - beagle_config.reset_gpio = 170; + beagle_config.dvi_pd_gpio = 170; beagle_config.usr_button_gpio = 7; break; case 6: printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3; beagle_config.mmc1_gpio_wp = 23; - beagle_config.reset_gpio = 170; + beagle_config.dvi_pd_gpio = 170; beagle_config.usr_button_gpio = 7; break; case 5: printk(KERN_INFO "OMAP3 Beagle Rev: C4\n"); omap3_beagle_version = OMAP3BEAGLE_BOARD_C4; beagle_config.mmc1_gpio_wp = 23; - beagle_config.reset_gpio = 170; + beagle_config.dvi_pd_gpio = 170; beagle_config.usr_button_gpio = 7; break; case 0: @@ -274,11 +274,9 @@ static int beagle_twl_gpio_setup(struct device *dev, if (r) pr_err("%s: unable to configure nDVI_PWR_EN\n", __func__); - r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH, - "DVI_LDO_EN"); - if (r) - pr_err("%s: unable to configure DVI_LDO_EN\n", - __func__); + + beagle_config.dvi_pd_gpio = gpio + 2; + } else { /* * REVISIT: need ehci-omap hooks for external VBUS @@ -287,7 +285,7 @@ static int beagle_twl_gpio_setup(struct device *dev, if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC")) pr_err("%s: unable to configure EHCI_nOC\n", __func__); } - dvi_panel.power_down_gpio = beagle_config.reset_gpio; + dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio; gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level, "nEN_USB_PWR"); @@ -499,7 +497,7 @@ static void __init omap3_beagle_init(void) omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); omap3_beagle_init_rev(); - if (beagle_config.mmc1_gpio_wp != -EINVAL) + if (gpio_is_valid(beagle_config.mmc1_gpio_wp)) omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT); mmc[0].caps = beagle_config.mmc_caps; omap_hsmmc_init(mmc); @@ -510,15 +508,13 @@ static void __init omap3_beagle_init(void) platform_add_devices(omap3_beagle_devices, ARRAY_SIZE(omap3_beagle_devices)); + if (gpio_is_valid(beagle_config.dvi_pd_gpio)) + omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT); omap_display_init(&beagle_dss_data); omap_serial_init(); omap_sdrc_init(mt46h32m32lf6_sdrc_params, mt46h32m32lf6_sdrc_params); - omap_mux_init_gpio(170, OMAP_PIN_INPUT); - /* REVISIT leave DVI powered down until it's needed ... */ - gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD"); - usb_musb_init(NULL); usbhs_init(&usbhs_bdata); omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions, diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c index 4c90477e6f82..d52651a05daa 100644 --- a/arch/arm/mach-omap2/omap_phy_internal.c +++ b/arch/arm/mach-omap2/omap_phy_internal.c @@ -239,21 +239,15 @@ void am35x_set_mode(u8 musb_mode) devconf2 &= ~CONF2_OTGMODE; switch (musb_mode) { -#ifdef CONFIG_USB_MUSB_HDRC_HCD case MUSB_HOST: /* Force VBUS valid, ID = 0 */ devconf2 |= CONF2_FORCE_HOST; break; -#endif -#ifdef CONFIG_USB_GADGET_MUSB_HDRC case MUSB_PERIPHERAL: /* Force VBUS valid, ID = 1 */ devconf2 |= CONF2_FORCE_DEVICE; break; -#endif -#ifdef CONFIG_USB_MUSB_OTG case MUSB_OTG: /* Don't override the VBUS/ID comparators */ devconf2 |= CONF2_NO_OVERRIDE; break; -#endif default: pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode); } diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index b19d1b43c12e..c4a576856661 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -41,12 +41,10 @@ static struct musb_hdrc_config musb_config = { }; static struct musb_hdrc_platform_data musb_plat = { -#ifdef CONFIG_USB_MUSB_OTG +#ifdef CONFIG_USB_GADGET_MUSB_HDRC .mode = MUSB_OTG, -#elif defined(CONFIG_USB_MUSB_HDRC_HCD) +#else .mode = MUSB_HOST, -#elif defined(CONFIG_USB_GADGET_MUSB_HDRC) - .mode = MUSB_PERIPHERAL, #endif /* .clock is set dynamically */ .config = &musb_config, diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c index db84a46ce7fd..805bea6edf17 100644 --- a/arch/arm/mach-omap2/usb-tusb6010.c +++ b/arch/arm/mach-omap2/usb-tusb6010.c @@ -300,7 +300,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data, printk(error, 3, status); return status; } - tusb_resources[2].start = irq + IH_GPIO_BASE; + tusb_resources[2].start = gpio_to_irq(irq); /* set up memory timings ... can speed them up later */ if (!ps_refclk) { |