diff options
| -rw-r--r-- | Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt | 42 | ||||
| -rw-r--r-- | drivers/reset/core.c | 15 | ||||
| -rw-r--r-- | drivers/reset/reset-socfpga.c | 15 | ||||
| -rw-r--r-- | drivers/reset/sti/Kconfig | 4 | ||||
| -rw-r--r-- | drivers/reset/sti/Makefile | 1 | ||||
| -rw-r--r-- | drivers/reset/sti/reset-stih407.c | 158 | ||||
| -rw-r--r-- | include/dt-bindings/reset-controller/stih407-resets.h | 61 | ||||
| -rw-r--r-- | include/linux/reset-controller.h | 2 | ||||
| -rw-r--r-- | include/linux/reset.h | 7 |
9 files changed, 305 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt new file mode 100644 index 000000000000..54ae9f747e45 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt @@ -0,0 +1,42 @@ +STMicroelectronics STi family Sysconfig Picophy SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in +the STi family SoC system configuration registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to Documentation/devicetree/bindings/reset/reset.txt +for common reset controller binding usage. + +Required properties: +- compatible: Should be "st,stih407-picophyreset" +- #reset-cells: 1, see below + +Example: + + picophyreset: picophyreset-controller { + compatible = "st,stih407-picophyreset"; + #reset-cells = <1>; + }; + +Specifying picophyreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the picophyreset device node and an +index specifying which channel to use, as described in +Documentation/devicetree/bindings/reset/reset.txt. + +Example: + + usb2_picophy0: usbpicophy@0 { + resets = <&picophyreset STIH407_PICOPHY0_RESET>; + }; + +Macro definitions for the supported reset channels can be found in: +include/dt-bindings/reset-controller/stih407-resets.h diff --git a/drivers/reset/core.c b/drivers/reset/core.c index baeaf82d40d9..7955e00d04d4 100644 --- a/drivers/reset/core.c +++ b/drivers/reset/core.c @@ -126,6 +126,21 @@ int reset_control_deassert(struct reset_control *rstc) EXPORT_SYMBOL_GPL(reset_control_deassert); /** + * reset_control_status - returns a negative errno if not supported, a + * positive value if the reset line is asserted, or zero if the reset + * line is not asserted. + * @rstc: reset controller + */ +int reset_control_status(struct reset_control *rstc) +{ + if (rstc->rcdev->ops->status) + return rstc->rcdev->ops->status(rstc->rcdev, rstc->id); + + return -ENOSYS; +} +EXPORT_SYMBOL_GPL(reset_control_status); + +/** * of_reset_control_get - Lookup and obtain a reference to a reset controller. * @node: device to be reset by the controller * @id: reset line name diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c index 79c32ca84ef1..40582089474a 100644 --- a/drivers/reset/reset-socfpga.c +++ b/drivers/reset/reset-socfpga.c @@ -76,9 +76,24 @@ static int socfpga_reset_deassert(struct reset_controller_dev *rcdev, return 0; } +static int socfpga_reset_status(struct reset_controller_dev *rcdev, + unsigned long id) +{ + struct socfpga_reset_data *data = container_of(rcdev, + struct socfpga_reset_data, rcdev); + int bank = id / BITS_PER_LONG; + int offset = id % BITS_PER_LONG; + u32 reg; + + reg = readl(data->membase + OFFSET_MODRST + (bank * NR_BANKS)); + + return !(reg & BIT(offset)); +} + static struct reset_control_ops socfpga_reset_ops = { .assert = socfpga_reset_assert, .deassert = socfpga_reset_deassert, + .status = socfpga_reset_status, }; static int socfpga_reset_probe(struct platform_device *pdev) diff --git a/drivers/reset/sti/Kconfig b/drivers/reset/sti/Kconfig index 88d2d0316613..f8c15a37fb35 100644 --- a/drivers/reset/sti/Kconfig +++ b/drivers/reset/sti/Kconfig @@ -12,4 +12,8 @@ config STIH416_RESET bool select STI_RESET_SYSCFG +config STIH407_RESET + bool + select STI_RESET_SYSCFG + endif diff --git a/drivers/reset/sti/Makefile b/drivers/reset/sti/Makefile index be1c97647871..dc85dfbe56a9 100644 --- a/drivers/reset/sti/Makefile +++ b/drivers/reset/sti/Makefile @@ -2,3 +2,4 @@ obj-$(CONFIG_STI_RESET_SYSCFG) += reset-syscfg.o obj-$(CONFIG_STIH415_RESET) += reset-stih415.o obj-$(CONFIG_STIH416_RESET) += reset-stih416.o +obj-$(CONFIG_STIH407_RESET) += reset-stih407.o diff --git a/drivers/reset/sti/reset-stih407.c b/drivers/reset/sti/reset-stih407.c new file mode 100644 index 000000000000..d83db5d72d08 --- /dev/null +++ b/drivers/reset/sti/reset-stih407.c @@ -0,0 +1,158 @@ +/* + * Copyright (C) 2014 STMicroelectronics (R&D) Limited + * Author: Giuseppe Cavallaro <peppe.cavallaro@st.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/platform_device.h> +#include <dt-bindings/reset-controller/stih407-resets.h> +#include "reset-syscfg.h" + +/* STiH407 Peripheral powerdown definitions. */ +static const char stih407_core[] = "st,stih407-core-syscfg"; +static const char stih407_sbc_reg[] = "st,stih407-sbc-reg-syscfg"; +static const char stih407_lpm[] = "st,stih407-lpm-syscfg"; + +#define STIH407_PDN_0(_bit) \ + _SYSCFG_RST_CH(stih407_core, SYSCFG_5000, _bit, SYSSTAT_5500, _bit) +#define STIH407_PDN_1(_bit) \ + _SYSCFG_RST_CH(stih407_core, SYSCFG_5001, _bit, SYSSTAT_5501, _bit) +#define STIH407_PDN_ETH(_bit, _stat) \ + _SYSCFG_RST_CH(stih407_sbc_reg, SYSCFG_4032, _bit, SYSSTAT_4520, _stat) + +/* Powerdown requests control 0 */ +#define SYSCFG_5000 0x0 +#define SYSSTAT_5500 0x7d0 +/* Powerdown requests control 1 (High Speed Links) */ +#define SYSCFG_5001 0x4 +#define SYSSTAT_5501 0x7d4 + +/* Ethernet powerdown/status/reset */ +#define SYSCFG_4032 0x80 +#define SYSSTAT_4520 0x820 +#define SYSCFG_4002 0x8 + +static const struct syscfg_reset_channel_data stih407_powerdowns[] = { + [STIH407_EMISS_POWERDOWN] = STIH407_PDN_0(1), + [STIH407_NAND_POWERDOWN] = STIH407_PDN_0(0), + [STIH407_USB3_POWERDOWN] = STIH407_PDN_1(6), + [STIH407_USB2_PORT1_POWERDOWN] = STIH407_PDN_1(5), + [STIH407_USB2_PORT0_POWERDOWN] = STIH407_PDN_1(4), + [STIH407_PCIE1_POWERDOWN] = STIH407_PDN_1(3), + [STIH407_PCIE0_POWERDOWN] = STIH407_PDN_1(2), + [STIH407_SATA1_POWERDOWN] = STIH407_PDN_1(1), + [STIH407_SATA0_POWERDOWN] = STIH407_PDN_1(0), + [STIH407_ETH1_POWERDOWN] = STIH407_PDN_ETH(0, 2), +}; + +/* Reset Generator control 0/1 */ +#define SYSCFG_5131 0x20c +#define SYSCFG_5132 0x210 + +#define LPM_SYSCFG_1 0x4 /* Softreset IRB & SBC UART */ + +#define STIH407_SRST_CORE(_reg, _bit) \ + _SYSCFG_RST_CH_NO_ACK(stih407_core, _reg, _bit) + +#define STIH407_SRST_SBC(_reg, _bit) \ + _SYSCFG_RST_CH_NO_ACK(stih407_sbc_reg, _reg, _bit) + +#define STIH407_SRST_LPM(_reg, _bit) \ + _SYSCFG_RST_CH_NO_ACK(stih407_lpm, _reg, _bit) + +static const struct syscfg_reset_channel_data stih407_softresets[] = { + [STIH407_ETH1_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 4), + [STIH407_MMC1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 3), + [STIH407_USB2_PORT0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 28), + [STIH407_USB2_PORT1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 29), + [STIH407_PICOPHY_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 30), + [STIH407_IRB_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 6), + [STIH407_PCIE0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 6), + [STIH407_PCIE1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 15), + [STIH407_SATA0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 7), + [STIH407_SATA1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 16), + [STIH407_MIPHY0_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 4), + [STIH407_MIPHY1_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 13), + [STIH407_MIPHY2_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 22), + [STIH407_SATA0_PWR_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 5), + [STIH407_SATA1_PWR_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 14), + [STIH407_DELTA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 3), + [STIH407_BLITTER_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 10), + [STIH407_HDTVOUT_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 11), + [STIH407_HDQVDP_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 12), + [STIH407_VDP_AUX_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 14), + [STIH407_COMPO_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 15), + [STIH407_HDMI_TX_PHY_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 21), + [STIH407_JPEG_DEC_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 23), + [STIH407_VP8_DEC_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 24), + [STIH407_GPU_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5131, 30), + [STIH407_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 0), + [STIH407_ERAM_HVA_SOFTRESET] = STIH407_SRST_CORE(SYSCFG_5132, 1), + [STIH407_LPM_SOFTRESET] = STIH407_SRST_SBC(SYSCFG_4002, 2), + [STIH407_KEYSCAN_SOFTRESET] = STIH407_SRST_LPM(LPM_SYSCFG_1, 8), +}; + +/* PicoPHY reset/control */ +#define SYSCFG_5061 0x0f4 + +static const struct syscfg_reset_channel_data stih407_picophyresets[] = { + [STIH407_PICOPHY0_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 5), + [STIH407_PICOPHY1_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 6), + [STIH407_PICOPHY2_RESET] = STIH407_SRST_CORE(SYSCFG_5061, 7), +}; + +static const struct syscfg_reset_controller_data stih407_powerdown_controller = { + .wait_for_ack = true, + .nr_channels = ARRAY_SIZE(stih407_powerdowns), + .channels = stih407_powerdowns, +}; + +static const struct syscfg_reset_controller_data stih407_softreset_controller = { + .wait_for_ack = false, + .active_low = true, + .nr_channels = ARRAY_SIZE(stih407_softresets), + .channels = stih407_softresets, +}; + +static const struct syscfg_reset_controller_data stih407_picophyreset_controller = { + .wait_for_ack = false, + .nr_channels = ARRAY_SIZE(stih407_picophyresets), + .channels = stih407_picophyresets, +}; + +static struct of_device_id stih407_reset_match[] = { + { + .compatible = "st,stih407-powerdown", + .data = &stih407_powerdown_controller, + }, + { + .compatible = "st,stih407-softreset", + .data = &stih407_softreset_controller, + }, + { + .compatible = "st,stih407-picophyreset", + .data = &stih407_picophyreset_controller, + }, + { /* sentinel */ }, +}; + +static struct platform_driver stih407_reset_driver = { + .probe = syscfg_reset_probe, + .driver = { + .name = "reset-stih407", + .of_match_table = stih407_reset_match, + }, +}; + +static int __init stih407_reset_init(void) +{ + return platform_driver_register(&stih407_reset_driver); +} + +arch_initcall(stih407_reset_init); diff --git a/include/dt-bindings/reset-controller/stih407-resets.h b/include/dt-bindings/reset-controller/stih407-resets.h new file mode 100644 index 000000000000..02d4328fe479 --- /dev/null +++ b/include/dt-bindings/reset-controller/stih407-resets.h @@ -0,0 +1,61 @@ +/* + * This header provides constants for the reset controller + * based peripheral powerdown requests on the STMicroelectronics + * STiH407 SoC. + */ +#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH407 +#define _DT_BINDINGS_RESET_CONTROLLER_STIH407 + +/* Powerdown requests control 0 */ +#define STIH407_EMISS_POWERDOWN 0 +#define STIH407_NAND_POWERDOWN 1 + +/* Synp GMAC PowerDown */ +#define STIH407_ETH1_POWERDOWN 2 + +/* Powerdown requests control 1 */ +#define STIH407_USB3_POWERDOWN 3 +#define STIH407_USB2_PORT1_POWERDOWN 4 +#define STIH407_USB2_PORT0_POWERDOWN 5 +#define STIH407_PCIE1_POWERDOWN 6 +#define STIH407_PCIE0_POWERDOWN 7 +#define STIH407_SATA1_POWERDOWN 8 +#define STIH407_SATA0_POWERDOWN 9 + +/* Reset defines */ +#define STIH407_ETH1_SOFTRESET 0 +#define STIH407_MMC1_SOFTRESET 1 +#define STIH407_PICOPHY_SOFTRESET 2 +#define STIH407_IRB_SOFTRESET 3 +#define STIH407_PCIE0_SOFTRESET 4 +#define STIH407_PCIE1_SOFTRESET 5 +#define STIH407_SATA0_SOFTRESET 6 +#define STIH407_SATA1_SOFTRESET 7 +#define STIH407_MIPHY0_SOFTRESET 8 +#define STIH407_MIPHY1_SOFTRESET 9 +#define STIH407_MIPHY2_SOFTRESET 10 +#define STIH407_SATA0_PWR_SOFTRESET 11 +#define STIH407_SATA1_PWR_SOFTRESET 12 +#define STIH407_DELTA_SOFTRESET 13 +#define STIH407_BLITTER_SOFTRESET 14 +#define STIH407_HDTVOUT_SOFTRESET 15 +#define STIH407_HDQVDP_SOFTRESET 16 +#define STIH407_VDP_AUX_SOFTRESET 17 +#define STIH407_COMPO_SOFTRESET 18 +#define STIH407_HDMI_TX_PHY_SOFTRESET 19 +#define STIH407_JPEG_DEC_SOFTRESET 20 +#define STIH407_VP8_DEC_SOFTRESET 21 +#define STIH407_GPU_SOFTRESET 22 +#define STIH407_HVA_SOFTRESET 23 +#define STIH407_ERAM_HVA_SOFTRESET 24 +#define STIH407_LPM_SOFTRESET 25 +#define STIH407_KEYSCAN_SOFTRESET 26 +#define STIH407_USB2_PORT0_SOFTRESET 27 +#define STIH407_USB2_PORT1_SOFTRESET 28 + +/* Picophy reset defines */ +#define STIH407_PICOPHY0_RESET 0 +#define STIH407_PICOPHY1_RESET 1 +#define STIH407_PICOPHY2_RESET 2 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH407 */ diff --git a/include/linux/reset-controller.h b/include/linux/reset-controller.h index 41a4695fde08..ce6b962ffed4 100644 --- a/include/linux/reset-controller.h +++ b/include/linux/reset-controller.h @@ -12,11 +12,13 @@ struct reset_controller_dev; * things to reset the device * @assert: manually assert the reset line, if supported * @deassert: manually deassert the reset line, if supported + * @status: return the status of the reset line, if supported */ struct reset_control_ops { int (*reset)(struct reset_controller_dev *rcdev, unsigned long id); int (*assert)(struct reset_controller_dev *rcdev, unsigned long id); int (*deassert)(struct reset_controller_dev *rcdev, unsigned long id); + int (*status)(struct reset_controller_dev *rcdev, unsigned long id); }; struct module; diff --git a/include/linux/reset.h b/include/linux/reset.h index 349f150ae12c..da5602bd77d7 100644 --- a/include/linux/reset.h +++ b/include/linux/reset.h @@ -10,6 +10,7 @@ struct reset_control; int reset_control_reset(struct reset_control *rstc); int reset_control_assert(struct reset_control *rstc); int reset_control_deassert(struct reset_control *rstc); +int reset_control_status(struct reset_control *rstc); struct reset_control *reset_control_get(struct device *dev, const char *id); void reset_control_put(struct reset_control *rstc); @@ -57,6 +58,12 @@ static inline int reset_control_deassert(struct reset_control *rstc) return 0; } +static inline int reset_control_status(struct reset_control *rstc) +{ + WARN_ON(1); + return 0; +} + static inline void reset_control_put(struct reset_control *rstc) { WARN_ON(1); |