diff options
41 files changed, 1596 insertions, 607 deletions
diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt new file mode 100644 index 000000000000..36b9aede3f40 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -0,0 +1,40 @@ +USB COMPARATOR OF TWL CHIPS + +TWL6030 USB COMPARATOR + - compatible : Should be "ti,twl6030-usb" + - interrupts : Two interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts when + the controller has to act as host and the second interrupt number is the + usb interrupt number that raises VBUS interrupts when the controller has to + act as device + - usb-supply : phandle to the regulator device tree node. It should be vusb + if it is twl6030 or ldousb if it is twl6025 subclass. + +twl6030-usb { + compatible = "ti,twl6030-usb"; + interrupts = < 4 10 >; +}; + +Board specific device node entry +&twl6030-usb { + usb-supply = <&vusb>; +}; + +TWL4030 USB PHY AND COMPARATOR + - compatible : Should be "ti,twl4030-usb" + - interrupts : The interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts + and VBUS interrupts. The second interrupt number is optional. + - <supply-name>-supply : phandle to the regulator device tree node. + <supply-name> should be vusb1v5, vusb1v8 and vusb3v1 + - usb_mode : The mode used by the phy to connect to the controller. "1" + specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode. + +twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = < 10 4 >; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt new file mode 100644 index 000000000000..80d4148cb661 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -0,0 +1,17 @@ +USB PHY + +OMAP USB2 PHY + +Required properties: + - compatible: Should be "ti,omap-usb2" + - reg : Address and length of the register set for the device. Also +add the address of control module dev conf register until a driver for +control module is added + +This is usually a subnode of ocp2scp to which it is connected. + +usb2phy@4a0ad080 { + compatible = "ti,omap-usb2"; + reg = <0x4a0ad080 0x58>, + <0x4a002300 0x4>; +}; diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 0d362e9f9cb9..3d2a988e3d9a 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -32,6 +32,7 @@ #include <linux/spi/ads7846.h> #include <linux/i2c/twl.h> #include <linux/usb/otg.h> +#include <linux/usb/nop-usb-xceiv.h> #include <linux/smsc911x.h> #include <linux/wl12xx.h> diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c index d52651a05daa..874aecc0faca 100644 --- a/arch/arm/mach-omap2/omap_phy_internal.c +++ b/arch/arm/mach-omap2/omap_phy_internal.c @@ -31,144 +31,6 @@ #include <plat/usb.h> #include "control.h" -/* OMAP control module register for UTMI PHY */ -#define CONTROL_DEV_CONF 0x300 -#define PHY_PD 0x1 - -#define USBOTGHS_CONTROL 0x33c -#define AVALID BIT(0) -#define BVALID BIT(1) -#define VBUSVALID BIT(2) -#define SESSEND BIT(3) -#define IDDIG BIT(4) - -static struct clk *phyclk, *clk48m, *clk32k; -static void __iomem *ctrl_base; -static int usbotghs_control; - -int omap4430_phy_init(struct device *dev) -{ - ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K); - if (!ctrl_base) { - pr_err("control module ioremap failed\n"); - return -ENOMEM; - } - /* Power down the phy */ - __raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF); - - if (!dev) { - iounmap(ctrl_base); - return 0; - } - - phyclk = clk_get(dev, "ocp2scp_usb_phy_ick"); - if (IS_ERR(phyclk)) { - dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n"); - iounmap(ctrl_base); - return PTR_ERR(phyclk); - } - - clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m"); - if (IS_ERR(clk48m)) { - dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n"); - clk_put(phyclk); - iounmap(ctrl_base); - return PTR_ERR(clk48m); - } - - clk32k = clk_get(dev, "usb_phy_cm_clk32k"); - if (IS_ERR(clk32k)) { - dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n"); - clk_put(phyclk); - clk_put(clk48m); - iounmap(ctrl_base); - return PTR_ERR(clk32k); - } - return 0; -} - -int omap4430_phy_set_clk(struct device *dev, int on) -{ - static int state; - - if (on && !state) { - /* Enable the phy clocks */ - clk_enable(phyclk); - clk_enable(clk48m); - clk_enable(clk32k); - state = 1; - } else if (state) { - /* Disable the phy clocks */ - clk_disable(phyclk); - clk_disable(clk48m); - clk_disable(clk32k); - state = 0; - } - return 0; -} - -int omap4430_phy_power(struct device *dev, int ID, int on) -{ - if (on) { - if (ID) - /* enable VBUS valid, IDDIG groung */ - __raw_writel(AVALID | VBUSVALID, ctrl_base + - USBOTGHS_CONTROL); - else - /* - * Enable VBUS Valid, AValid and IDDIG - * high impedance - */ - __raw_writel(IDDIG | AVALID | VBUSVALID, - ctrl_base + USBOTGHS_CONTROL); - } else { - /* Enable session END and IDIG to high impedance. */ - __raw_writel(SESSEND | IDDIG, ctrl_base + - USBOTGHS_CONTROL); - } - return 0; -} - -int omap4430_phy_suspend(struct device *dev, int suspend) -{ - if (suspend) { - /* Disable the clocks */ - omap4430_phy_set_clk(dev, 0); - /* Power down the phy */ - __raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF); - - /* save the context */ - usbotghs_control = __raw_readl(ctrl_base + USBOTGHS_CONTROL); - } else { - /* Enable the internel phy clcoks */ - omap4430_phy_set_clk(dev, 1); - /* power on the phy */ - if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) { - __raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF); - mdelay(200); - } - - /* restore the context */ - __raw_writel(usbotghs_control, ctrl_base + USBOTGHS_CONTROL); - } - - return 0; -} - -int omap4430_phy_exit(struct device *dev) -{ - if (ctrl_base) - iounmap(ctrl_base); - if (phyclk) - clk_put(phyclk); - if (clk48m) - clk_put(clk48m); - if (clk32k) - clk_put(clk32k); - - return 0; -} - void am35x_musb_reset(void) { u32 regval; diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index db5ff6642375..329b726012f3 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -251,11 +251,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data, #if defined(CONFIG_ARCH_OMAP4) static struct twl4030_usb_data omap4_usb_pdata = { - .phy_init = omap4430_phy_init, - .phy_exit = omap4430_phy_exit, - .phy_power = omap4430_phy_power, - .phy_set_clock = omap4430_phy_set_clk, - .phy_suspend = omap4430_phy_suspend, }; static struct regulator_init_data omap4_vdac_idata = { diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index c4a576856661..e9b4b234dc5f 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -117,7 +117,4 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data) dev->dma_mask = &musb_dmamask; dev->coherent_dma_mask = musb_dmamask; put_device(dev); - - if (cpu_is_omap44xx()) - omap4430_phy_init(dev); } diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile index b129f37515bb..ed41905a3bd1 100644 --- a/arch/arm/mach-tegra/Makefile +++ b/arch/arm/mach-tegra/Makefile @@ -23,7 +23,6 @@ obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o obj-$(CONFIG_TEGRA_SYSTEM_DMA) += dma.o obj-$(CONFIG_CPU_FREQ) += cpu-tegra.o obj-$(CONFIG_TEGRA_PCI) += pcie.o -obj-$(CONFIG_USB_SUPPORT) += usb_phy.o obj-$(CONFIG_ARCH_TEGRA_2x_SOC) += board-dt-tegra20.o obj-$(CONFIG_ARCH_TEGRA_3x_SOC) += board-dt-tegra30.o diff --git a/arch/arm/mach-tegra/devices.c b/arch/arm/mach-tegra/devices.c index c70e65ffa36b..d8ab76276397 100644 --- a/arch/arm/mach-tegra/devices.c +++ b/arch/arm/mach-tegra/devices.c @@ -27,7 +27,7 @@ #include <mach/irqs.h> #include <mach/iomap.h> #include <mach/dma.h> -#include <mach/usb_phy.h> +#include <linux/usb/tegra_usb_phy.h> #include "gpio-names.h" #include "devices.h" diff --git a/arch/arm/mach-tegra/devices.h b/arch/arm/mach-tegra/devices.h index 4f5052726495..906a61f340c8 100644 --- a/arch/arm/mach-tegra/devices.h +++ b/arch/arm/mach-tegra/devices.h @@ -22,7 +22,7 @@ #include <linux/platform_device.h> #include <linux/platform_data/tegra_usb.h> -#include <mach/usb_phy.h> +#include <linux/usb/tegra_usb_phy.h> extern struct tegra_ulpi_config tegra_ehci2_ulpi_phy_config; diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index c34452a7304f..79a24fab13d1 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -50,6 +50,7 @@ #include <linux/dma-mapping.h> #include <linux/of.h> +#include <linux/usb/otg.h> #include <linux/usb/ch9.h> #include <linux/usb/gadget.h> @@ -136,6 +137,8 @@ static void dwc3_core_soft_reset(struct dwc3 *dwc) reg |= DWC3_GUSB2PHYCFG_PHYSOFTRST; dwc3_writel(dwc->regs, DWC3_GUSB2PHYCFG(0), reg); + usb_phy_init(dwc->usb2_phy); + usb_phy_init(dwc->usb3_phy); mdelay(100); /* Clear USB3 PHY reset */ @@ -465,6 +468,18 @@ static int __devinit dwc3_probe(struct platform_device *pdev) return -ENOMEM; } + dwc->usb2_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB2); + if (IS_ERR_OR_NULL(dwc->usb2_phy)) { + dev_err(dev, "no usb2 phy configured\n"); + return -EPROBE_DEFER; + } + + dwc->usb3_phy = devm_usb_get_phy(dev, USB_PHY_TYPE_USB3); + if (IS_ERR_OR_NULL(dwc->usb3_phy)) { + dev_err(dev, "no usb3 phy configured\n"); + return -EPROBE_DEFER; + } + spin_lock_init(&dwc->lock); platform_set_drvdata(pdev, dwc); diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 151eca876dfd..dbc5713d84fb 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -624,6 +624,8 @@ struct dwc3_scratchpad_array { * @maximum_speed: maximum speed requested (mainly for testing purposes) * @revision: revision register contents * @mode: mode of operation + * @usb2_phy: pointer to USB2 PHY + * @usb3_phy: pointer to USB3 PHY * @is_selfpowered: true when we are selfpowered * @three_stage_setup: set if we perform a three phase setup * @ep0_bounced: true when we used bounce buffer @@ -667,6 +669,9 @@ struct dwc3 { struct usb_gadget gadget; struct usb_gadget_driver *gadget_driver; + struct usb_phy *usb2_phy; + struct usb_phy *usb3_phy; + void __iomem *regs; size_t regs_size; diff --git a/drivers/usb/dwc3/dwc3-exynos.c b/drivers/usb/dwc3/dwc3-exynos.c index b8f00389fa34..ca6597853f90 100644 --- a/drivers/usb/dwc3/dwc3-exynos.c +++ b/drivers/usb/dwc3/dwc3-exynos.c @@ -19,16 +19,74 @@ #include <linux/platform_data/dwc3-exynos.h> #include <linux/dma-mapping.h> #include <linux/clk.h> +#include <linux/usb/otg.h> +#include <linux/usb/nop-usb-xceiv.h> #include "core.h" struct dwc3_exynos { struct platform_device *dwc3; + struct platform_device *usb2_phy; + struct platform_device *usb3_phy; struct device *dev; struct clk *clk; }; +static int __devinit dwc3_exynos_register_phys(struct dwc3_exynos *exynos) +{ + struct nop_usb_xceiv_platform_data pdata; + struct platform_device *pdev; + int ret; + + memset(&pdata, 0x00, sizeof(pdata)); + + pdev = platform_device_alloc("nop_usb_xceiv", 0); + if (!pdev) + return -ENOMEM; + + exynos->usb2_phy = pdev; + pdata.type = USB_PHY_TYPE_USB2; + + ret = platform_device_add_data(exynos->usb2_phy, &pdata, sizeof(pdata)); + if (ret) + goto err1; + + pdev = platform_device_alloc("nop_usb_xceiv", 1); + if (!pdev) { + ret = -ENOMEM; + goto err1; + } + + exynos->usb3_phy = pdev; + pdata.type = USB_PHY_TYPE_USB3; + + ret = platform_device_add_data(exynos->usb3_phy, &pdata, sizeof(pdata)); + if (ret) + goto err2; + + ret = platform_device_add(exynos->usb2_phy); + if (ret) + goto err2; + + ret = platform_device_add(exynos->usb3_phy); + if (ret) + goto err3; + + return 0; + +err3: + platform_device_del(exynos->usb2_phy); + +err2: + platform_device_put(exynos->usb3_phy); + +err1: + platform_device_put(exynos->usb2_phy); + + return ret; +} + static int __devinit dwc3_exynos_probe(struct platform_device *pdev) { struct dwc3_exynos_data *pdata = pdev->dev.platform_data; @@ -51,6 +109,12 @@ static int __devinit dwc3_exynos_probe(struct platform_device *pdev) if (devid < 0) goto err1; + ret = dwc3_exynos_register_phys(exynos); + if (ret) { + dev_err(&pdev->dev, "couldn't register PHYs\n"); + goto err1; + } + dwc3 = platform_device_alloc("dwc3", devid); if (!dwc3) { dev_err(&pdev->dev, "couldn't allocate dwc3 device\n"); @@ -120,6 +184,8 @@ static int __devexit dwc3_exynos_remove(struct platform_device *pdev) struct dwc3_exynos_data *pdata = pdev->dev.platform_data; platform_device_unregister(exynos->dwc3); + platform_device_unregister(exynos->usb2_phy); + platform_device_unregister(exynos->usb3_phy); dwc3_put_device_id(exynos->dwc3->id); diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c index 479dc047da3a..ee57a10d90d0 100644 --- a/drivers/usb/dwc3/dwc3-omap.c +++ b/drivers/usb/dwc3/dwc3-omap.c @@ -48,6 +48,9 @@ #include <linux/io.h> #include <linux/of.h> +#include <linux/usb/otg.h> +#include <linux/usb/nop-usb-xceiv.h> + #include "core.h" /* @@ -131,6 +134,8 @@ struct dwc3_omap { spinlock_t lock; struct platform_device *dwc3; + struct platform_device *usb2_phy; + struct platform_device *usb3_phy; struct device *dev; int irq; @@ -152,6 +157,59 @@ static inline void dwc3_omap_writel(void __iomem *base, u32 offset, u32 value) writel(value, base + offset); } +static int __devinit dwc3_omap_register_phys(struct dwc3_omap *omap) +{ + struct nop_usb_xceiv_platform_data pdata; + struct platform_device *pdev; + int ret; + + memset(&pdata, 0x00, sizeof(pdata)); + + pdev = platform_device_alloc("nop_usb_xceiv", 0); + if (!pdev) + return -ENOMEM; + + omap->usb2_phy = pdev; + pdata.type = USB_PHY_TYPE_USB2; + + ret = platform_device_add_data(omap->usb2_phy, &pdata, sizeof(pdata)); + if (ret) + goto err1; + + pdev = platform_device_alloc("nop_usb_xceiv", 1); + if (!pdev) { + ret = -ENOMEM; + goto err1; + } + + omap->usb3_phy = pdev; + pdata.type = USB_PHY_TYPE_USB3; + + ret = platform_device_add_data(omap->usb3_phy, &pdata, sizeof(pdata)); + if (ret) + goto err2; + + ret = platform_device_add(omap->usb2_phy); + if (ret) + goto err2; + + ret = platform_device_add(omap->usb3_phy); + if (ret) + goto err3; + + return 0; + +err3: + platform_device_del(omap->usb2_phy); + +err2: + platform_device_put(omap->usb3_phy); + +err1: + platform_device_put(omap->usb2_phy); + + return ret; +} static irqreturn_t dwc3_omap_interrupt(int irq, void *_omap) { @@ -251,6 +309,12 @@ static int __devinit dwc3_omap_probe(struct platform_device *pdev) return -ENOMEM; } + ret = dwc3_omap_register_phys(omap); + if (ret) { + dev_err(dev, "couldn't register PHYs\n"); + return ret; + } + devid = dwc3_get_device_id(); if (devid < 0) return -ENODEV; @@ -371,6 +435,8 @@ static int __devexit dwc3_omap_remove(struct platform_device *pdev) struct dwc3_omap *omap = platform_get_drvdata(pdev); platform_device_unregister(omap->dwc3); + platform_device_unregister(omap->usb2_phy); + platform_device_unregister(omap->usb3_phy); dwc3_put_device_id(omap->dwc3->id); diff --git a/drivers/usb/dwc3/dwc3-pci.c b/drivers/usb/dwc3/dwc3-pci.c index a9ca9adba391..94f550e37f98 100644 --- a/drivers/usb/dwc3/dwc3-pci.c +++ b/drivers/usb/dwc3/dwc3-pci.c @@ -42,6 +42,9 @@ #include <linux/pci.h> #include <linux/platform_device.h> +#include <linux/usb/otg.h> +#include <linux/usb/nop-usb-xceiv.h> + #include "core.h" /* FIXME define these in <linux/pci_ids.h> */ @@ -51,8 +54,64 @@ struct dwc3_pci { struct device *dev; struct platform_device *dwc3; + struct platform_device *usb2_phy; + struct platform_device *usb3_phy; }; +static int __devinit dwc3_pci_register_phys(struct dwc3_pci *glue) +{ + struct nop_usb_xceiv_platform_data pdata; + struct platform_device *pdev; + int ret; + + memset(&pdata, 0x00, sizeof(pdata)); + + pdev = platform_device_alloc("nop_usb_xceiv", 0); + if (!pdev) + return -ENOMEM; + + glue->usb2_phy = pdev; + pdata.type = USB_PHY_TYPE_USB2; + + ret = platform_device_add_data(glue->usb2_phy, &pdata, sizeof(pdata)); + if (ret) + goto err1; + + pdev = platform_device_alloc("nop_usb_xceiv", 1); + if (!pdev) { + ret = -ENOMEM; + goto err1; + } + + glue->usb3_phy = pdev; + pdata.type = USB_PHY_TYPE_USB3; + + ret = platform_device_add_data(glue->usb3_phy, &pdata, sizeof(pdata)); + if (ret) + goto err2; + + ret = platform_device_add(glue->usb2_phy); + if (ret) + goto err2; + + ret = platform_device_add(glue->usb3_phy); + if (ret) + goto err3; + + return 0; + +err3: + platform_device_del(glue->usb2_phy); + +err2: + platform_device_put(glue->usb3_phy); + +err1: + platform_device_put(glue->usb2_phy); + + return ret; +} + static int __devinit dwc3_pci_probe(struct pci_dev *pci, const struct pci_device_id *id) { @@ -80,6 +139,12 @@ static int __devinit dwc3_pci_probe(struct pci_dev *pci, pci_set_power_state(pci, PCI_D0); pci_set_master(pci); + ret = dwc3_pci_register_phys(glue); + if (ret) { + dev_err(dev, "couldn't register PHYs\n"); + return ret; + } + devid = dwc3_get_device_id(); if (devid < 0) { ret = -ENOMEM; @@ -144,6 +209,8 @@ static void __devexit dwc3_pci_remove(struct pci_dev *pci) { struct dwc3_pci *glue = pci_get_drvdata(pci); + platform_device_unregister(glue->usb2_phy); + platform_device_unregister(glue->usb3_phy); dwc3_put_device_id(glue->dwc3->id); platform_device_unregister(glue->dwc3); pci_set_drvdata(pci, NULL); diff --git a/drivers/usb/host/ehci-tegra.c b/drivers/usb/host/ehci-tegra.c index 26dedb30ad0b..c0d47323b52a 100644 --- a/drivers/usb/host/ehci-tegra.c +++ b/drivers/usb/host/ehci-tegra.c @@ -27,7 +27,7 @@ #include <linux/of_gpio.h> #include <linux/pm_runtime.h> -#include <mach/usb_phy.h> +#include <linux/usb/tegra_usb_phy.h> #include <mach/iomap.h> #define TEGRA_USB_DMA_ALIGN 32 @@ -49,7 +49,7 @@ static void tegra_ehci_power_up(struct usb_hcd *hcd) clk_prepare_enable(tegra->emc_clk); clk_prepare_enable(tegra->clk); - tegra_usb_phy_power_on(tegra->phy); + usb_phy_set_suspend(&tegra->phy->u_phy, 0); tegra->host_resumed = 1; } @@ -58,7 +58,7 @@ static void tegra_ehci_power_down(struct usb_hcd *hcd) struct tegra_ehci_hcd *tegra = dev_get_drvdata(hcd->self.controller); tegra->host_resumed = 0; - tegra_usb_phy_power_off(tegra->phy); + usb_phy_set_suspend(&tegra->phy->u_phy, 1); clk_disable_unprepare(tegra->clk); clk_disable_unprepare(tegra->emc_clk); } @@ -715,7 +715,9 @@ static int tegra_ehci_probe(struct platform_device *pdev) goto fail_phy; } - err = tegra_usb_phy_power_on(tegra->phy); + usb_phy_init(&tegra->phy->u_phy); + + err = usb_phy_set_suspend(&tegra->phy->u_phy, 0); if (err) { dev_err(&pdev->dev, "Failed to power on the phy\n"); goto fail; @@ -762,7 +764,7 @@ fail: usb_put_phy(tegra->transceiver); } #endif - tegra_usb_phy_close(tegra->phy); + usb_phy_shutdown(&tegra->phy->u_phy); fail_phy: iounmap(hcd->regs); fail_io: @@ -800,7 +802,7 @@ static int tegra_ehci_remove(struct platform_device *pdev) usb_remove_hcd(hcd); - tegra_usb_phy_close(tegra->phy); + usb_phy_shutdown(&tegra->phy->u_phy); iounmap(hcd->regs); usb_put_hcd(hcd); diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c index 7a95ab87ac00..5d64c5b5ef52 100644 --- a/drivers/usb/musb/am35x.c +++ b/drivers/usb/musb/am35x.c @@ -33,6 +33,7 @@ #include <linux/io.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> +#include <linux/usb/nop-usb-xceiv.h> #include <plat/usb.h> diff --git a/drivers/usb/musb/blackfin.c b/drivers/usb/musb/blackfin.c index 428e6aa3e78a..b562623a8971 100644 --- a/drivers/usb/musb/blackfin.c +++ b/drivers/usb/musb/blackfin.c @@ -19,6 +19,7 @@ #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/prefetch.h> +#include <linux/usb/nop-usb-xceiv.h> #include <asm/cacheflush.h> diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c index 0f9fcec4e1d3..16798c9e6f38 100644 --- a/drivers/usb/musb/da8xx.c +++ b/drivers/usb/musb/da8xx.c @@ -33,6 +33,7 @@ #include <linux/io.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> +#include <linux/usb/nop-usb-xceiv.h> #include <mach/da8xx.h> #include <mach/usb.h> diff --git a/drivers/usb/musb/davinci.c b/drivers/usb/musb/davinci.c index 472c8b42d38b..863a9b6286c3 100644 --- a/drivers/usb/musb/davinci.c +++ b/drivers/usb/musb/davinci.c @@ -33,6 +33,7 @@ #include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> +#include <linux/usb/nop-usb-xceiv.h> #include <mach/cputype.h> #include <mach/hardware.h> diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c index 494772fc9e23..c20b8776aafa 100644 --- a/drivers/usb/musb/musb_dsps.c +++ b/drivers/usb/musb/musb_dsps.c @@ -36,6 +36,7 @@ #include <linux/dma-mapping.h> #include <linux/pm_runtime.h> #include <linux/module.h> +#include <linux/usb/nop-usb-xceiv.h> #include <linux/of.h> #include <linux/of_device.h> diff --git a/drivers/usb/musb/tusb6010.c b/drivers/usb/musb/tusb6010.c index 1a1bd9cf40c5..00f21dfee5d7 100644 --- a/drivers/usb/musb/tusb6010.c +++ b/drivers/usb/musb/tusb6010.c @@ -24,6 +24,7 @@ #include <linux/irq.h> #include <linux/platform_device.h> #include <linux/dma-mapping.h> +#include <linux/usb/nop-usb-xceiv.h> #include "musb_core.h" diff --git a/drivers/usb/otg/Kconfig b/drivers/usb/otg/Kconfig index 13fd1ddf742f..d8c8a42bff3e 100644 --- a/drivers/usb/otg/Kconfig +++ b/drivers/usb/otg/Kconfig @@ -68,7 +68,7 @@ config TWL4030_USB config TWL6030_USB tristate "TWL6030 USB Transceiver Driver" - depends on TWL4030_CORE + depends on TWL4030_CORE && OMAP_USB2 select USB_OTG_UTILS help Enable this to support the USB OTG transceiver on TWL6030 diff --git a/drivers/usb/otg/fsl_otg.c b/drivers/usb/otg/fsl_otg.c index 23c798cb2d7f..c19d1d7173a9 100644 --- a/drivers/usb/otg/fsl_otg.c +++ b/drivers/usb/otg/fsl_otg.c @@ -544,9 +544,13 @@ int fsl_otg_start_gadget(struct otg_fsm *fsm, int on) */ static int fsl_otg_set_host(struct usb_otg *otg, struct usb_bus *host) { - struct fsl_otg *otg_dev = container_of(otg->phy, struct fsl_otg, phy); + struct fsl_otg *otg_dev; + + if (!otg) + return -ENODEV; - if (!otg || otg_dev != fsl_otg_dev) + otg_dev = container_of(otg->phy, struct fsl_otg, phy); + if (otg_dev != fsl_otg_dev) return -ENODEV; otg->host = host; @@ -590,12 +594,15 @@ static int fsl_otg_set_host(struct usb_otg *otg, struct usb_bus *host) static int fsl_otg_set_peripheral(struct usb_otg *otg, struct usb_gadget *gadget) { - struct fsl_otg *otg_dev = container_of(otg->phy, struct fsl_otg, phy); + struct fsl_otg *otg_dev; + if (!otg) + return -ENODEV; + + otg_dev = container_of(otg->phy, struct fsl_otg, phy); VDBG("otg_dev 0x%x\n", (int)otg_dev); VDBG("fsl_otg_dev 0x%x\n", (int)fsl_otg_dev); - - if (!otg || otg_dev != fsl_otg_dev) + if (otg_dev != fsl_otg_dev) return -ENODEV; if (!gadget) { @@ -660,10 +667,13 @@ static void fsl_otg_event(struct work_struct *work) /* B-device start SRP */ static int fsl_otg_start_srp(struct usb_otg *otg) { - struct fsl_otg *otg_dev = container_of(otg->phy, struct fsl_otg, phy); + struct fsl_otg *otg_dev; + + if (!otg || otg->phy->state != OTG_STATE_B_IDLE) + return -ENODEV; - if (!otg || otg_dev != fsl_otg_dev - || otg->phy->state != OTG_STATE_B_IDLE) + otg_dev = container_of(otg->phy, struct fsl_otg, phy); + if (otg_dev != fsl_otg_dev) return -ENODEV; otg_dev->fsm.b_bus_req = 1; @@ -675,9 +685,13 @@ static int fsl_otg_start_srp(struct usb_otg *otg) /* A_host suspend will call this function to start hnp */ static int fsl_otg_start_hnp(struct usb_otg *otg) { - struct fsl_otg *otg_dev = container_of(otg->phy, struct fsl_otg, phy); + struct fsl_otg *otg_dev; + + if (!otg) + return -ENODEV; - if (!otg || otg_dev != fsl_otg_dev) + otg_dev = container_of(otg->phy, struct fsl_otg, phy); + if (otg_dev != fsl_otg_dev) return -ENODEV; DBG("start_hnp...n"); diff --git a/drivers/usb/otg/mxs-phy.c b/drivers/usb/otg/mxs-phy.c index c1a67cb8e244..88db976647cf 100644 --- a/drivers/usb/otg/mxs-phy.c +++ b/drivers/usb/otg/mxs-phy.c @@ -20,6 +20,7 @@ #include <linux/delay.h> #include <linux/err.h> #include <linux/io.h> +#include <linux/workqueue.h> #define DRIVER_NAME "mxs_phy" @@ -34,9 +35,16 @@ #define BM_USBPHY_CTRL_ENUTMILEVEL2 BIT(14) #define BM_USBPHY_CTRL_ENHOSTDISCONDETECT BIT(1) +/* + * Amount of delay in miliseconds to safely enable ENHOSTDISCONDETECT bit + * so that connection and reset processing can be completed for the root hub. + */ +#define MXY_PHY_ENHOSTDISCONDETECT_DELAY 250 + struct mxs_phy { struct usb_phy phy; struct clk *clk; + struct delayed_work enhostdiscondetect_work; }; #define to_mxs_phy(p) container_of((p), struct mxs_phy, phy) @@ -62,6 +70,7 @@ static int mxs_phy_init(struct usb_phy *phy) clk_prepare_enable(mxs_phy->clk); mxs_phy_hw_init(mxs_phy); + INIT_DELAYED_WORK(&mxs_phy->enhostdiscondetect_work, NULL); return 0; } @@ -76,13 +85,34 @@ static void mxs_phy_shutdown(struct usb_phy *phy) clk_disable_unprepare(mxs_phy->clk); } +static void mxs_phy_enhostdiscondetect_delay(struct work_struct *ws) +{ + struct mxs_phy *mxs_phy = container_of(ws, struct mxs_phy, + enhostdiscondetect_work.work); + + /* Enable HOSTDISCONDETECT after delay. */ + dev_dbg(mxs_phy->phy.dev, "Setting ENHOSTDISCONDETECT\n"); + writel_relaxed(BM_USBPHY_CTRL_ENHOSTDISCONDETECT, + mxs_phy->phy.io_priv + HW_USBPHY_CTRL_SET); +} + static int mxs_phy_on_connect(struct usb_phy *phy, int port) { + struct mxs_phy *mxs_phy = to_mxs_phy(phy); + dev_dbg(phy->dev, "Connect on port %d\n", port); - mxs_phy_hw_init(to_mxs_phy(phy)); - writel_relaxed(BM_USBPHY_CTRL_ENHOSTDISCONDETECT, - phy->io_priv + HW_USBPHY_CTRL_SET); + mxs_phy_hw_init(mxs_phy); + + /* + * Delay enabling ENHOSTDISCONDETECT so that connection and + * reset processing can be completed for the root hub. + */ + dev_dbg(phy->dev, "Delaying setting ENHOSTDISCONDETECT\n"); + PREPARE_DELAYED_WORK(&mxs_phy->enhostdiscondetect_work, + mxs_phy_enhostdiscondetect_delay); + schedule_delayed_work(&mxs_phy->enhostdiscondetect_work, + msecs_to_jiffies(MXY_PHY_ENHOSTDISCONDETECT_DELAY)); return 0; } @@ -91,6 +121,8 @@ static int mxs_phy_on_disconnect(struct usb_phy *phy, int port) { dev_dbg(phy->dev, "Disconnect on port %d\n", port); + /* No need to delay before clearing ENHOSTDISCONDETECT. */ + dev_dbg(phy->dev, "Clearing ENHOSTDISCONDETECT\n"); writel_relaxed(BM_USBPHY_CTRL_ENHOSTDISCONDETECT, phy->io_priv + HW_USBPHY_CTRL_CLR); diff --git a/drivers/usb/otg/nop-usb-xceiv.c b/drivers/usb/otg/nop-usb-xceiv.c index 803f958f4133..e52e35e7adaf 100644 --- a/drivers/usb/otg/nop-usb-xceiv.c +++ b/drivers/usb/otg/nop-usb-xceiv.c @@ -30,6 +30,7 @@ #include <linux/platform_device.h> #include <linux/dma-mapping.h> #include <linux/usb/otg.h> +#include <linux/usb/nop-usb-xceiv.h> #include <linux/slab.h> struct nop_usb_xceiv { @@ -94,7 +95,9 @@ static int nop_set_host(struct usb_otg *otg, struct usb_bus *host) static int __devinit nop_usb_xceiv_probe(struct platform_device *pdev) { + struct nop_usb_xceiv_platform_data *pdata = pdev->dev.platform_data; struct nop_usb_xceiv *nop; + enum usb_phy_type type = USB_PHY_TYPE_USB2; int err; nop = kzalloc(sizeof *nop, GFP_KERNEL); @@ -107,6 +110,9 @@ static int __devinit nop_usb_xceiv_probe(struct platform_device *pdev) return -ENOMEM; } + if (pdata) + type = pdata->type; + nop->dev = &pdev->dev; nop->phy.dev = nop->dev; nop->phy.label = "nop-xceiv"; @@ -117,7 +123,7 @@ static int __devinit nop_usb_xceiv_probe(struct platform_device *pdev) nop->phy.otg->set_host = nop_set_host; nop->phy.otg->set_peripheral = nop_set_peripheral; - err = usb_add_phy(&nop->phy, USB_PHY_TYPE_USB2); + err = usb_add_phy(&nop->phy, type); if (err) { dev_err(&pdev->dev, "can't register transceiver, err: %d\n", err); diff --git a/drivers/usb/otg/otg.c b/drivers/usb/otg/otg.c index 1bf60a22595c..a30c04115115 100644 --- a/drivers/usb/otg/otg.c +++ b/drivers/usb/otg/otg.c @@ -159,7 +159,7 @@ int usb_add_phy(struct usb_phy *x, enum usb_phy_type type) unsigned long flags; struct usb_phy *phy; - if (x && x->type != USB_PHY_TYPE_UNDEFINED) { + if (x->type != USB_PHY_TYPE_UNDEFINED) { dev_err(x->dev, "not accepting initialized PHY %s\n", x->label); return -EINVAL; } diff --git a/drivers/usb/otg/twl4030-usb.c b/drivers/usb/otg/twl4030-usb.c index 523cad5bfea9..f0d2e7530cfe 100644 --- a/drivers/usb/otg/twl4030-usb.c +++ b/drivers/usb/otg/twl4030-usb.c @@ -585,23 +585,28 @@ static int __devinit twl4030_usb_probe(struct platform_device *pdev) struct twl4030_usb *twl; int status, err; struct usb_otg *otg; - - if (!pdata) { - dev_dbg(&pdev->dev, "platform_data not available\n"); - return -EINVAL; - } + struct device_node *np = pdev->dev.of_node; twl = devm_kzalloc(&pdev->dev, sizeof *twl, GFP_KERNEL); if (!twl) return -ENOMEM; + if (np) + of_property_read_u32(np, "usb_mode", + (enum twl4030_usb_mode *)&twl->usb_mode); + else if (pdata) + twl->usb_mode = pdata->usb_mode; + else { + dev_err(&pdev->dev, "twl4030 initialized without pdata\n"); + return -EINVAL; + } + otg = devm_kzalloc(&pdev->dev, sizeof *otg, GFP_KERNEL); if (!otg) return -ENOMEM; twl->dev = &pdev->dev; twl->irq = platform_get_irq(pdev, 0); - twl->usb_mode = pdata->usb_mode; twl->vbus_supplied = false; twl->asleep = 1; twl->linkstat = OMAP_MUSB_UNKNOWN; @@ -690,12 +695,21 @@ static int __exit twl4030_usb_remove(struct platform_device *pdev) return 0; } +#ifdef CONFIG_OF +static const struct of_device_id twl4030_usb_id_table[] = { + { .compatible = "ti,twl4030-usb" }, + {} +}; +MODULE_DEVICE_TABLE(of, twl4030_usb_id_table); +#endif + static struct platform_driver twl4030_usb_driver = { .probe = twl4030_usb_probe, .remove = __exit_p(twl4030_usb_remove), .driver = { .name = "twl4030_usb", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(twl4030_usb_id_table), }, }; diff --git a/drivers/usb/otg/twl6030-usb.c b/drivers/usb/otg/twl6030-usb.c index 6907d8df7a27..fcadef7864f1 100644 --- a/drivers/usb/otg/twl6030-usb.c +++ b/drivers/usb/otg/twl6030-usb.c @@ -25,8 +25,9 @@ #include <linux/interrupt.h> #include <linux/platform_device.h> #include <linux/io.h> -#include <linux/usb/otg.h> #include <linux/usb/musb-omap.h> +#include <linux/usb/phy_companion.h> +#include <linux/usb/omap_usb.h> #include <linux/i2c/twl.h> #include <linux/regulator/consumer.h> #include <linux/err.h> @@ -87,7 +88,7 @@ #define VBUS_DET BIT(2) struct twl6030_usb { - struct usb_phy phy; + struct phy_companion comparator; struct device *dev; /* for vbus reporting with irqs disabled */ @@ -104,10 +105,10 @@ struct twl6030_usb { u8 asleep; bool irq_enabled; bool vbus_enable; - unsigned long features; + const char *regulator; }; -#define phy_to_twl(x) container_of((x), struct twl6030_usb, phy) +#define comparator_to_twl(x) container_of((x), struct twl6030_usb, comparator) /*-------------------------------------------------------------------------*/ @@ -137,50 +138,9 @@ static inline u8 twl6030_readb(struct twl6030_usb *twl, u8 module, u8 address) return ret; } -static int twl6030_phy_init(struct usb_phy *x) +static int twl6030_start_srp(struct phy_companion *comparator) { - struct twl6030_usb *twl; - struct device *dev; - struct twl4030_usb_data *pdata; - - twl = phy_to_twl(x); - dev = twl->dev; - pdata = dev->platform_data; - - if (twl->linkstat == OMAP_MUSB_ID_GROUND) - pdata->phy_power(twl->dev, 1, 1); - else - pdata->phy_power(twl->dev, 0, 1); - - return 0; -} - -static void twl6030_phy_shutdown(struct usb_phy *x) -{ - struct twl6030_usb *twl; - struct device *dev; - struct twl4030_usb_data *pdata; - - twl = phy_to_twl(x); - dev = twl->dev; - pdata = dev->platform_data; - pdata->phy_power(twl->dev, 0, 0); -} - -static int twl6030_phy_suspend(struct usb_phy *x, int suspend) -{ - struct twl6030_usb *twl = phy_to_twl(x); - struct device *dev = twl->dev; - struct twl4030_usb_data *pdata = dev->platform_data; - - pdata->phy_suspend(dev, suspend); - - return 0; -} - -static int twl6030_start_srp(struct usb_otg *otg) -{ - struct twl6030_usb *twl = phy_to_twl(otg->phy); + struct twl6030_usb *twl = comparator_to_twl(comparator); twl6030_writeb(twl, TWL_MODULE_USB, 0x24, USB_VBUS_CTRL_SET); twl6030_writeb(twl, TWL_MODULE_USB, 0x84, USB_VBUS_CTRL_SET); @@ -193,13 +153,6 @@ static int twl6030_start_srp(struct usb_otg *otg) static int twl6030_usb_ldo_init(struct twl6030_usb *twl) { - char *regulator_name; - - if (twl->features & TWL6025_SUBCLASS) - regulator_name = "ldousb"; - else - regulator_name = "vusb"; - /* Set to OTG_REV 1.3 and turn on the ID_WAKEUP_COMP */ twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x1, TWL6030_BACKUP_REG); @@ -209,7 +162,7 @@ static int twl6030_usb_ldo_init(struct twl6030_usb *twl) /* Program MISC2 register and set bit VUSB_IN_VBAT */ twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x10, TWL6030_MISC2); - twl->usb3v3 = regulator_get(twl->dev, regulator_name); + twl->usb3v3 = regulator_get(twl->dev, twl->regulator); if (IS_ERR(twl->usb3v3)) return -ENODEV; @@ -313,23 +266,8 @@ static irqreturn_t twl6030_usbotg_irq(int irq, void *_twl) return IRQ_HANDLED; } -static int twl6030_set_peripheral(struct usb_otg *otg, - struct usb_gadget *gadget) -{ - if (!otg) - return -ENODEV; - - otg->gadget = gadget; - if (!gadget) - otg->phy->state = OTG_STATE_UNDEFINED; - - return 0; -} - -static int twl6030_enable_irq(struct usb_phy *x) +static int twl6030_enable_irq(struct twl6030_usb *twl) { - struct twl6030_usb *twl = phy_to_twl(x); - twl6030_writeb(twl, TWL_MODULE_USB, 0x1, USB_ID_INT_EN_HI_SET); twl6030_interrupt_unmask(0x05, REG_INT_MSK_LINE_C); twl6030_interrupt_unmask(0x05, REG_INT_MSK_STS_C); @@ -362,9 +300,9 @@ static void otg_set_vbus_work(struct work_struct *data) CHARGERUSB_CTRL1); } -static int twl6030_set_vbus(struct usb_otg *otg, bool enabled) +static int twl6030_set_vbus(struct phy_companion *comparator, bool enabled) { - struct twl6030_usb *twl = phy_to_twl(otg->phy); + struct twl6030_usb *twl = comparator_to_twl(comparator); twl->vbus_enable = enabled; schedule_work(&twl->set_vbus_work); @@ -372,52 +310,44 @@ static int twl6030_set_vbus(struct usb_otg *otg, bool enabled) return 0; } -static int twl6030_set_host(struct usb_otg *otg, struct usb_bus *host) -{ - if (!otg) - return -ENODEV; - - otg->host = host; - if (!host) - otg->phy->state = OTG_STATE_UNDEFINED; - return 0; -} - static int __devinit twl6030_usb_probe(struct platform_device *pdev) { + u32 ret; struct twl6030_usb *twl; int status, err; - struct twl4030_usb_data *pdata; - struct usb_otg *otg; - struct device *dev = &pdev->dev; - pdata = dev->platform_data; + struct device_node *np = pdev->dev.of_node; + struct device *dev = &pdev->dev; + struct twl4030_usb_data *pdata = dev->platform_data; twl = devm_kzalloc(dev, sizeof *twl, GFP_KERNEL); if (!twl) return -ENOMEM; - otg = devm_kzalloc(dev, sizeof *otg, GFP_KERNEL); - if (!otg) - return -ENOMEM; - twl->dev = &pdev->dev; twl->irq1 = platform_get_irq(pdev, 0); twl->irq2 = platform_get_irq(pdev, 1); - twl->features = pdata->features; twl->linkstat = OMAP_MUSB_UNKNOWN; - twl->phy.dev = twl->dev; - twl->phy.label = "twl6030"; - twl->phy.otg = otg; - twl->phy.init = twl6030_phy_init; - twl->phy.shutdown = twl6030_phy_shutdown; - twl->phy.set_suspend = twl6030_phy_suspend; + twl->comparator.set_vbus = twl6030_set_vbus; + twl->comparator.start_srp = twl6030_start_srp; + + ret = omap_usb2_set_comparator(&twl->comparator); + if (ret == -ENODEV) { + dev_info(&pdev->dev, "phy not ready, deferring probe"); + return -EPROBE_DEFER; + } - otg->phy = &twl->phy; - otg->set_host = twl6030_set_host; - otg->set_peripheral = twl6030_set_peripheral; - otg->set_vbus = twl6030_set_vbus; - otg->start_srp = twl6030_start_srp; + if (np) { + twl->regulator = "usb"; + } else if (pdata) { + if (pdata->features & TWL6025_SUBCLASS) + twl->regulator = "ldousb"; + else + twl->regulator = "vusb"; + } else { + dev_err(&pdev->dev, "twl6030 initialized without pdata\n"); + return -EINVAL; + } /* init spinlock for workqueue */ spin_lock_init(&twl->lock); @@ -427,7 +357,6 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev) dev_err(&pdev->dev, "ldo init failed\n"); return err; } - usb_add_phy(&twl->phy, USB_PHY_TYPE_USB2); platform_set_drvdata(pdev, twl); if (device_create_file(&pdev->dev, &dev_attr_vbus)) @@ -458,9 +387,7 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev) } twl->asleep = 0; - pdata->phy_init(dev); - twl6030_phy_suspend(&twl->phy, 0); - twl6030_enable_irq(&twl->phy); + twl6030_enable_irq(twl); dev_info(&pdev->dev, "Initialized TWL6030 USB module\n"); return 0; @@ -470,10 +397,6 @@ static int __exit twl6030_usb_remove(struct platform_device *pdev) { struct twl6030_usb *twl = platform_get_drvdata(pdev); - struct twl4030_usb_data *pdata; - struct device *dev = &pdev->dev; - pdata = dev->platform_data; - twl6030_interrupt_mask(TWL6030_USBOTG_INT_MASK, REG_INT_MSK_LINE_C); twl6030_interrupt_mask(TWL6030_USBOTG_INT_MASK, @@ -481,19 +404,27 @@ static int __exit twl6030_usb_remove(struct platform_device *pdev) free_irq(twl->irq1, twl); free_irq(twl->irq2, twl); regulator_put(twl->usb3v3); - pdata->phy_exit(twl->dev); device_remove_file(twl->dev, &dev_attr_vbus); cancel_work_sync(&twl->set_vbus_work); return 0; } +#ifdef CONFIG_OF +static const struct of_device_id twl6030_usb_id_table[] = { + { .compatible = "ti,twl6030-usb" }, + {} +}; +MODULE_DEVICE_TABLE(of, twl6030_usb_id_table); +#endif + static struct platform_driver twl6030_usb_driver = { .probe = twl6030_usb_probe, .remove = __exit_p(twl6030_usb_remove), .driver = { .name = "twl6030_usb", .owner = THIS_MODULE, + .of_match_table = of_match_ptr(twl6030_usb_id_table), }, }; diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig index e7cf84f0751a..63c339b3e676 100644 --- a/drivers/usb/phy/Kconfig +++ b/drivers/usb/phy/Kconfig @@ -4,6 +4,15 @@ comment "USB Physical Layer drivers" depends on USB || USB_GADGET +config OMAP_USB2 + tristate "OMAP USB2 PHY Driver" + select USB_OTG_UTILS + help + Enable this to support the transceiver that is part of SOC. This + driver takes care of all the PHY functionality apart from comparator. + The USB OTG controller communicates with the comparator using this + driver. + config USB_ISP1301 tristate "NXP ISP1301 USB transceiver support" depends on USB || USB_GADGET @@ -15,3 +24,11 @@ config USB_ISP1301 To compile this driver as a module, choose M here: the module will be called isp1301. + +config MV_U3D_PHY + bool "Marvell USB 3.0 PHY controller Driver" + depends on USB_MV_U3D + select USB_OTG_UTILS + help + Enable this to support Marvell USB 3.0 phy controller for Marvell + SoC. diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile index eca095b1a890..b069f29f1225 100644 --- a/drivers/usb/phy/Makefile +++ b/drivers/usb/phy/Makefile @@ -4,4 +4,7 @@ ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG +obj-$(CONFIG_OMAP_USB2) += omap-usb2.o obj-$(CONFIG_USB_ISP1301) += isp1301.o +obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o +obj-$(CONFIG_USB_EHCI_TEGRA) += tegra_usb_phy.o diff --git a/drivers/usb/phy/isp1301.c b/drivers/usb/phy/isp1301.c index b19f4932a037..18dbf7e37607 100644 --- a/drivers/usb/phy/isp1301.c +++ b/drivers/usb/phy/isp1301.c @@ -15,12 +15,6 @@ #define DRV_NAME "isp1301" -#define ISP1301_I2C_ADDR 0x2C - -static const unsigned short normal_i2c[] = { - ISP1301_I2C_ADDR, ISP1301_I2C_ADDR + 1, I2C_CLIENT_END -}; - static const struct i2c_device_id isp1301_id[] = { { "isp1301", 0 }, { } diff --git a/drivers/usb/phy/mv_u3d_phy.c b/drivers/usb/phy/mv_u3d_phy.c new file mode 100644 index 000000000000..9f1c5d3c60ec --- /dev/null +++ b/drivers/usb/phy/mv_u3d_phy.c @@ -0,0 +1,345 @@ +/* + * Copyright (C) 2011 Marvell International Ltd. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/io.h> +#include <linux/usb/otg.h> +#include <linux/platform_data/mv_usb.h> + +#include "mv_u3d_phy.h" + +/* + * struct mv_u3d_phy - transceiver driver state + * @phy: transceiver structure + * @dev: The parent device supplied to the probe function + * @clk: usb phy clock + * @base: usb phy register memory base + */ +struct mv_u3d_phy { + struct usb_phy phy; + struct mv_usb_platform_data *plat; + struct device *dev; + struct clk *clk; + void __iomem *base; +}; + +static u32 mv_u3d_phy_read(void __iomem *base, u32 reg) +{ + void __iomem *addr, *data; + + addr = base; + data = base + 0x4; + + writel_relaxed(reg, addr); + return readl_relaxed(data); +} + +static void mv_u3d_phy_set(void __iomem *base, u32 reg, u32 value) +{ + void __iomem *addr, *data; + u32 tmp; + + addr = base; + data = base + 0x4; + + writel_relaxed(reg, addr); + tmp = readl_relaxed(data); + tmp |= value; + writel_relaxed(tmp, data); +} + +static void mv_u3d_phy_clear(void __iomem *base, u32 reg, u32 value) +{ + void __iomem *addr, *data; + u32 tmp; + + addr = base; + data = base + 0x4; + + writel_relaxed(reg, addr); + tmp = readl_relaxed(data); + tmp &= ~value; + writel_relaxed(tmp, data); +} + +static void mv_u3d_phy_write(void __iomem *base, u32 reg, u32 value) +{ + void __iomem *addr, *data; + + addr = base; + data = base + 0x4; + + writel_relaxed(reg, addr); + writel_relaxed(value, data); +} + +void mv_u3d_phy_shutdown(struct usb_phy *phy) +{ + struct mv_u3d_phy *mv_u3d_phy; + void __iomem *base; + u32 val; + + mv_u3d_phy = container_of(phy, struct mv_u3d_phy, phy); + base = mv_u3d_phy->base; + + /* Power down Reference Analog current, bit 15 + * Power down PLL, bit 14 + * Power down Receiver, bit 13 + * Power down Transmitter, bit 12 + * of USB3_POWER_PLL_CONTROL register + */ + val = mv_u3d_phy_read(base, USB3_POWER_PLL_CONTROL); + val &= ~(USB3_POWER_PLL_CONTROL_PU); + mv_u3d_phy_write(base, USB3_POWER_PLL_CONTROL, val); + + if (mv_u3d_phy->clk) + clk_disable(mv_u3d_phy->clk); +} + +static int mv_u3d_phy_init(struct usb_phy *phy) +{ + struct mv_u3d_phy *mv_u3d_phy; + void __iomem *base; + u32 val, count; + + /* enable usb3 phy */ + mv_u3d_phy = container_of(phy, struct mv_u3d_phy, phy); + + if (mv_u3d_phy->clk) + clk_enable(mv_u3d_phy->clk); + + base = mv_u3d_phy->base; + + val = mv_u3d_phy_read(base, USB3_POWER_PLL_CONTROL); + val &= ~(USB3_POWER_PLL_CONTROL_PU_MASK); + val |= 0xF << USB3_POWER_PLL_CONTROL_PU_SHIFT; + mv_u3d_phy_write(base, USB3_POWER_PLL_CONTROL, val); + udelay(100); + + mv_u3d_phy_write(base, USB3_RESET_CONTROL, + USB3_RESET_CONTROL_RESET_PIPE); + udelay(100); + + mv_u3d_phy_write(base, USB3_RESET_CONTROL, + USB3_RESET_CONTROL_RESET_PIPE + | USB3_RESET_CONTROL_RESET_PHY); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_POWER_PLL_CONTROL); + val &= ~(USB3_POWER_PLL_CONTROL_REF_FREF_SEL_MASK + | USB3_POWER_PLL_CONTROL_PHY_MODE_MASK); + val |= (USB3_PLL_25MHZ << USB3_POWER_PLL_CONTROL_REF_FREF_SEL_SHIFT) + | (0x5 << USB3_POWER_PLL_CONTROL_PHY_MODE_SHIFT); + mv_u3d_phy_write(base, USB3_POWER_PLL_CONTROL, val); + udelay(100); + + mv_u3d_phy_clear(base, USB3_KVCO_CALI_CONTROL, + USB3_KVCO_CALI_CONTROL_USE_MAX_PLL_RATE_MASK); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_SQUELCH_FFE); + val &= ~(USB3_SQUELCH_FFE_FFE_CAP_SEL_MASK + | USB3_SQUELCH_FFE_FFE_RES_SEL_MASK + | USB3_SQUELCH_FFE_SQ_THRESH_IN_MASK); + val |= ((0xD << USB3_SQUELCH_FFE_FFE_CAP_SEL_SHIFT) + | (0x7 << USB3_SQUELCH_FFE_FFE_RES_SEL_SHIFT) + | (0x8 << USB3_SQUELCH_FFE_SQ_THRESH_IN_SHIFT)); + mv_u3d_phy_write(base, USB3_SQUELCH_FFE, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_GEN1_SET0); + val &= ~USB3_GEN1_SET0_G1_TX_SLEW_CTRL_EN_MASK; + val |= 1 << USB3_GEN1_SET0_G1_TX_EMPH_EN_SHIFT; + mv_u3d_phy_write(base, USB3_GEN1_SET0, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_GEN2_SET0); + val &= ~(USB3_GEN2_SET0_G2_TX_AMP_MASK + | USB3_GEN2_SET0_G2_TX_EMPH_AMP_MASK + | USB3_GEN2_SET0_G2_TX_SLEW_CTRL_EN_MASK); + val |= ((0x14 << USB3_GEN2_SET0_G2_TX_AMP_SHIFT) + | (1 << USB3_GEN2_SET0_G2_TX_AMP_ADJ_SHIFT) + | (0xA << USB3_GEN2_SET0_G2_TX_EMPH_AMP_SHIFT) + | (1 << USB3_GEN2_SET0_G2_TX_EMPH_EN_SHIFT)); + mv_u3d_phy_write(base, USB3_GEN2_SET0, val); + udelay(100); + + mv_u3d_phy_read(base, USB3_TX_EMPPH); + val &= ~(USB3_TX_EMPPH_AMP_MASK + | USB3_TX_EMPPH_EN_MASK + | USB3_TX_EMPPH_AMP_FORCE_MASK + | USB3_TX_EMPPH_PAR1_MASK + | USB3_TX_EMPPH_PAR2_MASK); + val |= ((0xB << USB3_TX_EMPPH_AMP_SHIFT) + | (1 << USB3_TX_EMPPH_EN_SHIFT) + | (1 << USB3_TX_EMPPH_AMP_FORCE_SHIFT) + | (0x1C << USB3_TX_EMPPH_PAR1_SHIFT) + | (1 << USB3_TX_EMPPH_PAR2_SHIFT)); + + mv_u3d_phy_write(base, USB3_TX_EMPPH, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_GEN2_SET1); + val &= ~(USB3_GEN2_SET1_G2_RX_SELMUPI_MASK + | USB3_GEN2_SET1_G2_RX_SELMUPF_MASK + | USB3_GEN2_SET1_G2_RX_SELMUFI_MASK + | USB3_GEN2_SET1_G2_RX_SELMUFF_MASK); + val |= ((1 << USB3_GEN2_SET1_G2_RX_SELMUPI_SHIFT) + | (1 << USB3_GEN2_SET1_G2_RX_SELMUPF_SHIFT) + | (1 << USB3_GEN2_SET1_G2_RX_SELMUFI_SHIFT) + | (1 << USB3_GEN2_SET1_G2_RX_SELMUFF_SHIFT)); + mv_u3d_phy_write(base, USB3_GEN2_SET1, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_DIGITAL_LOOPBACK_EN); + val &= ~USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_MASK; + val |= 1 << USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_SHIFT; + mv_u3d_phy_write(base, USB3_DIGITAL_LOOPBACK_EN, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_IMPEDANCE_TX_SSC); + val &= ~USB3_IMPEDANCE_TX_SSC_SSC_AMP_MASK; + val |= 0xC << USB3_IMPEDANCE_TX_SSC_SSC_AMP_SHIFT; + mv_u3d_phy_write(base, USB3_IMPEDANCE_TX_SSC, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_IMPEDANCE_CALI_CTRL); + val &= ~USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_MASK; + val |= 0x4 << USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_SHIFT; + mv_u3d_phy_write(base, USB3_IMPEDANCE_CALI_CTRL, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_PHY_ISOLATION_MODE); + val &= ~(USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_MASK + | USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_MASK + | USB3_PHY_ISOLATION_MODE_TX_DRV_IDLE_MASK); + val |= ((1 << USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_SHIFT) + | (1 << USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_SHIFT)); + mv_u3d_phy_write(base, USB3_PHY_ISOLATION_MODE, val); + udelay(100); + + val = mv_u3d_phy_read(base, USB3_TXDETRX); + val &= ~(USB3_TXDETRX_VTHSEL_MASK); + val |= 0x1 << USB3_TXDETRX_VTHSEL_SHIFT; + mv_u3d_phy_write(base, USB3_TXDETRX, val); + udelay(100); + + dev_dbg(mv_u3d_phy->dev, "start calibration\n"); + +calstart: + /* Perform Manual Calibration */ + mv_u3d_phy_set(base, USB3_KVCO_CALI_CONTROL, + 1 << USB3_KVCO_CALI_CONTROL_CAL_START_SHIFT); + + mdelay(1); + + count = 0; + while (1) { + val = mv_u3d_phy_read(base, USB3_KVCO_CALI_CONTROL); + if (val & (1 << USB3_KVCO_CALI_CONTROL_CAL_DONE_SHIFT)) + break; + else if (count > 50) { + dev_dbg(mv_u3d_phy->dev, "calibration failure, retry...\n"); + goto calstart; + } + count++; + mdelay(1); + } + + /* active PIPE interface */ + mv_u3d_phy_write(base, USB3_PIPE_SM_CTRL, + 1 << USB3_PIPE_SM_CTRL_PHY_INIT_DONE); + + return 0; +} + +static int __devinit mv_u3d_phy_probe(struct platform_device *pdev) +{ + struct mv_u3d_phy *mv_u3d_phy; + struct mv_usb_platform_data *pdata; + struct device *dev = &pdev->dev; + struct resource *res; + void __iomem *phy_base; + int ret; + + pdata = pdev->dev.platform_data; + if (!pdata) { + dev_err(&pdev->dev, "%s: no platform data defined\n", __func__); + return -EINVAL; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(dev, "missing mem resource\n"); + return -ENODEV; + } + + phy_base = devm_request_and_ioremap(dev, res); + if (!phy_base) { + dev_err(dev, "%s: register mapping failed\n", __func__); + return -ENXIO; + } + + mv_u3d_phy = devm_kzalloc(dev, sizeof(*mv_u3d_phy), GFP_KERNEL); + if (!mv_u3d_phy) + return -ENOMEM; + + mv_u3d_phy->dev = &pdev->dev; + mv_u3d_phy->plat = pdata; + mv_u3d_phy->base = phy_base; + mv_u3d_phy->phy.dev = mv_u3d_phy->dev; + mv_u3d_phy->phy.label = "mv-u3d-phy"; + mv_u3d_phy->phy.init = mv_u3d_phy_init; + mv_u3d_phy->phy.shutdown = mv_u3d_phy_shutdown; + + ret = usb_add_phy(&mv_u3d_phy->phy, USB_PHY_TYPE_USB3); + if (ret) + goto err; + + if (!mv_u3d_phy->clk) + mv_u3d_phy->clk = clk_get(mv_u3d_phy->dev, "u3dphy"); + + platform_set_drvdata(pdev, mv_u3d_phy); + + dev_info(&pdev->dev, "Initialized Marvell USB 3.0 PHY\n"); +err: + return ret; +} + +static int __exit mv_u3d_phy_remove(struct platform_device *pdev) +{ + struct mv_u3d_phy *mv_u3d_phy = platform_get_drvdata(pdev); + + usb_remove_phy(&mv_u3d_phy->phy); + + if (mv_u3d_phy->clk) { + clk_put(mv_u3d_phy->clk); + mv_u3d_phy->clk = NULL; + } + + return 0; +} + +static struct platform_driver mv_u3d_phy_driver = { + .probe = mv_u3d_phy_probe, + .remove = __devexit_p(mv_u3d_phy_remove), + .driver = { + .name = "mv-u3d-phy", + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(mv_u3d_phy_driver); +MODULE_DESCRIPTION("Marvell USB 3.0 PHY controller"); +MODULE_AUTHOR("Yu Xu <yuxu@marvell.com>"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:mv-u3d-phy"); diff --git a/drivers/usb/phy/mv_u3d_phy.h b/drivers/usb/phy/mv_u3d_phy.h new file mode 100644 index 000000000000..2a658cb9a527 --- /dev/null +++ b/drivers/usb/phy/mv_u3d_phy.h @@ -0,0 +1,105 @@ +/* + * Copyright (C) 2011 Marvell International Ltd. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + */ + +#ifndef __MV_U3D_PHY_H +#define __MV_U3D_PHY_H + +#define USB3_POWER_PLL_CONTROL 0x1 +#define USB3_KVCO_CALI_CONTROL 0x2 +#define USB3_IMPEDANCE_CALI_CTRL 0x3 +#define USB3_IMPEDANCE_TX_SSC 0x4 +#define USB3_SQUELCH_FFE 0x6 +#define USB3_GEN1_SET0 0xD +#define USB3_GEN2_SET0 0xF +#define USB3_GEN2_SET1 0x10 +#define USB3_DIGITAL_LOOPBACK_EN 0x23 +#define USB3_PHY_ISOLATION_MODE 0x26 +#define USB3_TXDETRX 0x48 +#define USB3_TX_EMPPH 0x5E +#define USB3_RESET_CONTROL 0x90 +#define USB3_PIPE_SM_CTRL 0x91 + +#define USB3_RESET_CONTROL_RESET_PIPE 0x1 +#define USB3_RESET_CONTROL_RESET_PHY 0x2 + +#define USB3_POWER_PLL_CONTROL_REF_FREF_SEL_MASK (0x1F << 0) +#define USB3_POWER_PLL_CONTROL_REF_FREF_SEL_SHIFT 0 +#define USB3_PLL_25MHZ 0x2 +#define USB3_PLL_26MHZ 0x5 +#define USB3_POWER_PLL_CONTROL_PHY_MODE_MASK (0x7 << 5) +#define USB3_POWER_PLL_CONTROL_PHY_MODE_SHIFT 5 +#define USB3_POWER_PLL_CONTROL_PU_MASK (0xF << 12) +#define USB3_POWER_PLL_CONTROL_PU_SHIFT 12 +#define USB3_POWER_PLL_CONTROL_PU (0xF << 12) + +#define USB3_KVCO_CALI_CONTROL_USE_MAX_PLL_RATE_MASK (0x1 << 12) +#define USB3_KVCO_CALI_CONTROL_USE_MAX_PLL_RATE_SHIFT 12 +#define USB3_KVCO_CALI_CONTROL_CAL_DONE_SHIFT 14 +#define USB3_KVCO_CALI_CONTROL_CAL_START_SHIFT 15 + +#define USB3_SQUELCH_FFE_FFE_CAP_SEL_MASK 0xF +#define USB3_SQUELCH_FFE_FFE_CAP_SEL_SHIFT 0 +#define USB3_SQUELCH_FFE_FFE_RES_SEL_MASK (0x7 << 4) +#define USB3_SQUELCH_FFE_FFE_RES_SEL_SHIFT 4 +#define USB3_SQUELCH_FFE_SQ_THRESH_IN_MASK (0x1F << 8) +#define USB3_SQUELCH_FFE_SQ_THRESH_IN_SHIFT 8 + +#define USB3_GEN1_SET0_G1_TX_SLEW_CTRL_EN_MASK (0x1 << 15) +#define USB3_GEN1_SET0_G1_TX_EMPH_EN_SHIFT 11 + +#define USB3_GEN2_SET0_G2_TX_AMP_MASK (0x1F << 1) +#define USB3_GEN2_SET0_G2_TX_AMP_SHIFT 1 +#define USB3_GEN2_SET0_G2_TX_AMP_ADJ_SHIFT 6 +#define USB3_GEN2_SET0_G2_TX_EMPH_AMP_MASK (0xF << 7) +#define USB3_GEN2_SET0_G2_TX_EMPH_AMP_SHIFT 7 +#define USB3_GEN2_SET0_G2_TX_EMPH_EN_MASK (0x1 << 11) +#define USB3_GEN2_SET0_G2_TX_EMPH_EN_SHIFT 11 +#define USB3_GEN2_SET0_G2_TX_SLEW_CTRL_EN_MASK (0x1 << 15) +#define USB3_GEN2_SET0_G2_TX_SLEW_CTRL_EN_SHIFT 15 + +#define USB3_GEN2_SET1_G2_RX_SELMUPI_MASK (0x7 << 0) +#define USB3_GEN2_SET1_G2_RX_SELMUPI_SHIFT 0 +#define USB3_GEN2_SET1_G2_RX_SELMUPF_MASK (0x7 << 3) +#define USB3_GEN2_SET1_G2_RX_SELMUPF_SHIFT 3 +#define USB3_GEN2_SET1_G2_RX_SELMUFI_MASK (0x3 << 6) +#define USB3_GEN2_SET1_G2_RX_SELMUFI_SHIFT 6 +#define USB3_GEN2_SET1_G2_RX_SELMUFF_MASK (0x3 << 8) +#define USB3_GEN2_SET1_G2_RX_SELMUFF_SHIFT 8 + +#define USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_MASK (0x3 << 10) +#define USB3_DIGITAL_LOOPBACK_EN_SEL_BITS_SHIFT 10 + +#define USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_MASK (0x7 << 12) +#define USB3_IMPEDANCE_CALI_CTRL_IMP_CAL_THR_SHIFT 12 + +#define USB3_IMPEDANCE_TX_SSC_SSC_AMP_MASK (0x3F << 0) +#define USB3_IMPEDANCE_TX_SSC_SSC_AMP_SHIFT 0 + +#define USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_MASK 0xF +#define USB3_PHY_ISOLATION_MODE_PHY_GEN_RX_SHIFT 0 +#define USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_MASK (0xF << 4) +#define USB3_PHY_ISOLATION_MODE_PHY_GEN_TX_SHIFT 4 +#define USB3_PHY_ISOLATION_MODE_TX_DRV_IDLE_MASK (0x1 << 8) + +#define USB3_TXDETRX_VTHSEL_MASK (0x3 << 4) +#define USB3_TXDETRX_VTHSEL_SHIFT 4 + +#define USB3_TX_EMPPH_AMP_MASK (0xF << 0) +#define USB3_TX_EMPPH_AMP_SHIFT 0 +#define USB3_TX_EMPPH_EN_MASK (0x1 << 6) +#define USB3_TX_EMPPH_EN_SHIFT 6 +#define USB3_TX_EMPPH_AMP_FORCE_MASK (0x1 << 7) +#define USB3_TX_EMPPH_AMP_FORCE_SHIFT 7 +#define USB3_TX_EMPPH_PAR1_MASK (0x1F << 8) +#define USB3_TX_EMPPH_PAR1_SHIFT 8 +#define USB3_TX_EMPPH_PAR2_MASK (0x1 << 13) +#define USB3_TX_EMPPH_PAR2_SHIFT 13 + +#define USB3_PIPE_SM_CTRL_PHY_INIT_DONE 15 + +#endif /* __MV_U3D_PHY_H */ diff --git a/drivers/usb/phy/omap-usb2.c b/drivers/usb/phy/omap-usb2.c new file mode 100644 index 000000000000..15ab3d6f2e8c --- /dev/null +++ b/drivers/usb/phy/omap-usb2.c @@ -0,0 +1,271 @@ +/* + * omap-usb2.c - USB PHY, talking to musb controller in OMAP. + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Kishon Vijay Abraham I <kishon@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/of.h> +#include <linux/io.h> +#include <linux/usb/omap_usb.h> +#include <linux/usb/phy_companion.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/pm_runtime.h> +#include <linux/delay.h> + +/** + * omap_usb2_set_comparator - links the comparator present in the sytem with + * this phy + * @comparator - the companion phy(comparator) for this phy + * + * The phy companion driver should call this API passing the phy_companion + * filled with set_vbus and start_srp to be used by usb phy. + * + * For use by phy companion driver + */ +int omap_usb2_set_comparator(struct phy_companion *comparator) +{ + struct omap_usb *phy; + struct usb_phy *x = usb_get_phy(USB_PHY_TYPE_USB2); + + if (IS_ERR(x)) + return -ENODEV; + + phy = phy_to_omapusb(x); + phy->comparator = comparator; + return 0; +} +EXPORT_SYMBOL_GPL(omap_usb2_set_comparator); + +/** + * omap_usb_phy_power - power on/off the phy using control module reg + * @phy: struct omap_usb * + * @on: 0 or 1, based on powering on or off the PHY + * + * XXX: Remove this function once control module driver gets merged + */ +static void omap_usb_phy_power(struct omap_usb *phy, int on) +{ + u32 val; + + if (on) { + val = readl(phy->control_dev); + if (val & PHY_PD) { + writel(~PHY_PD, phy->control_dev); + /* XXX: add proper documentation for this delay */ + mdelay(200); + } + } else { + writel(PHY_PD, phy->control_dev); + } +} + +static int omap_usb_set_vbus(struct usb_otg *otg, bool enabled) +{ + struct omap_usb *phy = phy_to_omapusb(otg->phy); + + if (!phy->comparator) + return -ENODEV; + + return phy->comparator->set_vbus(phy->comparator, enabled); +} + +static int omap_usb_start_srp(struct usb_otg *otg) +{ + struct omap_usb *phy = phy_to_omapusb(otg->phy); + + if (!phy->comparator) + return -ENODEV; + + return phy->comparator->start_srp(phy->comparator); +} + +static int omap_usb_set_host(struct usb_otg *otg, struct usb_bus *host) +{ + struct usb_phy *phy = otg->phy; + + otg->host = host; + if (!host) + phy->state = OTG_STATE_UNDEFINED; + + return 0; +} + +static int omap_usb_set_peripheral(struct usb_otg *otg, + struct usb_gadget *gadget) +{ + struct usb_phy *phy = otg->phy; + + otg->gadget = gadget; + if (!gadget) + phy->state = OTG_STATE_UNDEFINED; + + return 0; +} + +static int omap_usb2_suspend(struct usb_phy *x, int suspend) +{ + u32 ret; + struct omap_usb *phy = phy_to_omapusb(x); + + if (suspend && !phy->is_suspended) { + omap_usb_phy_power(phy, 0); + pm_runtime_put_sync(phy->dev); + phy->is_suspended = 1; + } else if (!suspend && phy->is_suspended) { + ret = pm_runtime_get_sync(phy->dev); + if (ret < 0) { + dev_err(phy->dev, "get_sync failed with err %d\n", + ret); + return ret; + } + omap_usb_phy_power(phy, 1); + phy->is_suspended = 0; + } + + return 0; +} + +static int __devinit omap_usb2_probe(struct platform_device *pdev) +{ + struct omap_usb *phy; + struct usb_otg *otg; + struct resource *res; + + phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL); + if (!phy) { + dev_err(&pdev->dev, "unable to allocate memory for USB2 PHY\n"); + return -ENOMEM; + } + + otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL); + if (!otg) { + dev_err(&pdev->dev, "unable to allocate memory for USB OTG\n"); + return -ENOMEM; + } + + phy->dev = &pdev->dev; + + phy->phy.dev = phy->dev; + phy->phy.label = "omap-usb2"; + phy->phy.set_suspend = omap_usb2_suspend; + phy->phy.otg = otg; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + + phy->control_dev = devm_request_and_ioremap(&pdev->dev, res); + if (phy->control_dev == NULL) { + dev_err(&pdev->dev, "Failed to obtain io memory\n"); + return -ENXIO; + } + + phy->is_suspended = 1; + omap_usb_phy_power(phy, 0); + + otg->set_host = omap_usb_set_host; + otg->set_peripheral = omap_usb_set_peripheral; + otg->set_vbus = omap_usb_set_vbus; + otg->start_srp = omap_usb_start_srp; + otg->phy = &phy->phy; + + phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k"); + if (IS_ERR(phy->wkupclk)) { + dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n"); + return PTR_ERR(phy->wkupclk); + } + clk_prepare(phy->wkupclk); + + usb_add_phy(&phy->phy, USB_PHY_TYPE_USB2); + + platform_set_drvdata(pdev, phy); + + pm_runtime_enable(phy->dev); + + return 0; +} + +static int __devexit omap_usb2_remove(struct platform_device *pdev) +{ + struct omap_usb *phy = platform_get_drvdata(pdev); + + clk_unprepare(phy->wkupclk); + usb_remove_phy(&phy->phy); + + return 0; +} + +#ifdef CONFIG_PM_RUNTIME + +static int omap_usb2_runtime_suspend(struct device *dev) +{ + struct platform_device *pdev = to_platform_device(dev); + struct omap_usb *phy = platform_get_drvdata(pdev); + + clk_disable(phy->wkupclk); + + return 0; +} + +static int omap_usb2_runtime_resume(struct device *dev) +{ + u32 ret = 0; + struct platform_device *pdev = to_platform_device(dev); + struct omap_usb *phy = platform_get_drvdata(pdev); + + ret = clk_enable(phy->wkupclk); + if (ret < 0) + dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret); + + return ret; +} + +static const struct dev_pm_ops omap_usb2_pm_ops = { + SET_RUNTIME_PM_OPS(omap_usb2_runtime_suspend, omap_usb2_runtime_resume, + NULL) +}; + +#define DEV_PM_OPS (&omap_usb2_pm_ops) +#else +#define DEV_PM_OPS NULL +#endif + +#ifdef CONFIG_OF +static const struct of_device_id omap_usb2_id_table[] = { + { .compatible = "ti,omap-usb2" }, + {} +}; +MODULE_DEVICE_TABLE(of, omap_usb2_id_table); +#endif + +static struct platform_driver omap_usb2_driver = { + .probe = omap_usb2_probe, + .remove = __devexit_p(omap_usb2_remove), + .driver = { + .name = "omap-usb2", + .owner = THIS_MODULE, + .pm = DEV_PM_OPS, + .of_match_table = of_match_ptr(omap_usb2_id_table), + }, +}; + +module_platform_driver(omap_usb2_driver); + +MODULE_ALIAS("platform: omap_usb2"); +MODULE_AUTHOR("Texas Instruments Inc."); +MODULE_DESCRIPTION("OMAP USB2 phy driver"); +MODULE_LICENSE("GPL v2"); diff --git a/arch/arm/mach-tegra/usb_phy.c b/drivers/usb/phy/tegra_usb_phy.c index 022b33a05c3a..4739903245e8 100644 --- a/arch/arm/mach-tegra/usb_phy.c +++ b/drivers/usb/phy/tegra_usb_phy.c @@ -1,6 +1,4 @@ /* - * arch/arm/mach-tegra/usb_phy.c - * * Copyright (C) 2010 Google, Inc. * * Author: @@ -31,7 +29,7 @@ #include <linux/usb/ulpi.h> #include <asm/mach-types.h> #include <mach/gpio-tegra.h> -#include <mach/usb_phy.h> +#include <linux/usb/tegra_usb_phy.h> #include <mach/iomap.h> #define ULPI_VIEWPORT 0x170 @@ -482,7 +480,7 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy) return 0; } -static void utmi_phy_power_off(struct tegra_usb_phy *phy) +static int utmi_phy_power_off(struct tegra_usb_phy *phy) { unsigned long val; void __iomem *base = phy->regs; @@ -514,7 +512,7 @@ static void utmi_phy_power_off(struct tegra_usb_phy *phy) UTMIP_FORCE_PDDR_POWERDOWN; writel(val, base + UTMIP_XCVR_CFG1); - utmip_pad_power_off(phy); + return utmip_pad_power_off(phy); } static void utmi_phy_preresume(struct tegra_usb_phy *phy) @@ -638,7 +636,7 @@ static int ulpi_phy_power_on(struct tegra_usb_phy *phy) return 0; } -static void ulpi_phy_power_off(struct tegra_usb_phy *phy) +static int ulpi_phy_power_off(struct tegra_usb_phy *phy) { unsigned long val; void __iomem *base = phy->regs; @@ -651,15 +649,92 @@ static void ulpi_phy_power_off(struct tegra_usb_phy *phy) val &= ~(USB_PORTSC1_WKOC | USB_PORTSC1_WKDS | USB_PORTSC1_WKCN); writel(val, base + USB_PORTSC1); - gpio_direction_output(config->reset_gpio, 0); clk_disable(phy->clk); + return gpio_direction_output(config->reset_gpio, 0); +} + +static int tegra_phy_init(struct usb_phy *x) +{ + struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + struct tegra_ulpi_config *ulpi_config; + int err; + + if (phy_is_ulpi(phy)) { + ulpi_config = phy->config; + phy->clk = clk_get_sys(NULL, ulpi_config->clk); + if (IS_ERR(phy->clk)) { + pr_err("%s: can't get ulpi clock\n", __func__); + err = -ENXIO; + goto err1; + } + if (!gpio_is_valid(ulpi_config->reset_gpio)) + ulpi_config->reset_gpio = + of_get_named_gpio(phy->dev->of_node, + "nvidia,phy-reset-gpio", 0); + if (!gpio_is_valid(ulpi_config->reset_gpio)) { + pr_err("%s: invalid reset gpio: %d\n", __func__, + ulpi_config->reset_gpio); + err = -EINVAL; + goto err1; + } + gpio_request(ulpi_config->reset_gpio, "ulpi_phy_reset_b"); + gpio_direction_output(ulpi_config->reset_gpio, 0); + phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0); + phy->ulpi->io_priv = phy->regs + ULPI_VIEWPORT; + } else { + err = utmip_pad_open(phy); + if (err < 0) + goto err1; + } + return 0; +err1: + clk_disable_unprepare(phy->pll_u); + clk_put(phy->pll_u); + return err; +} + +static void tegra_usb_phy_close(struct usb_phy *x) +{ + struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + + if (phy_is_ulpi(phy)) + clk_put(phy->clk); + else + utmip_pad_close(phy); + clk_disable_unprepare(phy->pll_u); + clk_put(phy->pll_u); + kfree(phy); +} + +static int tegra_usb_phy_power_on(struct tegra_usb_phy *phy) +{ + if (phy_is_ulpi(phy)) + return ulpi_phy_power_on(phy); + else + return utmi_phy_power_on(phy); +} + +static int tegra_usb_phy_power_off(struct tegra_usb_phy *phy) +{ + if (phy_is_ulpi(phy)) + return ulpi_phy_power_off(phy); + else + return utmi_phy_power_off(phy); +} + +static int tegra_usb_phy_suspend(struct usb_phy *x, int suspend) +{ + struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy); + if (suspend) + return tegra_usb_phy_power_off(phy); + else + return tegra_usb_phy_power_on(phy); } struct tegra_usb_phy *tegra_usb_phy_open(struct device *dev, int instance, void __iomem *regs, void *config, enum tegra_usb_phy_mode phy_mode) { struct tegra_usb_phy *phy; - struct tegra_ulpi_config *ulpi_config; unsigned long parent_rate; int i; int err; @@ -672,6 +747,7 @@ struct tegra_usb_phy *tegra_usb_phy_open(struct device *dev, int instance, phy->regs = regs; phy->config = config; phy->mode = phy_mode; + phy->dev = dev; if (!phy->config) { if (phy_is_ulpi(phy)) { @@ -704,33 +780,9 @@ struct tegra_usb_phy *tegra_usb_phy_open(struct device *dev, int instance, goto err1; } - if (phy_is_ulpi(phy)) { - ulpi_config = config; - phy->clk = clk_get_sys(NULL, ulpi_config->clk); - if (IS_ERR(phy->clk)) { - pr_err("%s: can't get ulpi clock\n", __func__); - err = -ENXIO; - goto err1; - } - if (!gpio_is_valid(ulpi_config->reset_gpio)) - ulpi_config->reset_gpio = - of_get_named_gpio(dev->of_node, - "nvidia,phy-reset-gpio", 0); - if (!gpio_is_valid(ulpi_config->reset_gpio)) { - pr_err("%s: invalid reset gpio: %d\n", __func__, - ulpi_config->reset_gpio); - err = -EINVAL; - goto err1; - } - gpio_request(ulpi_config->reset_gpio, "ulpi_phy_reset_b"); - gpio_direction_output(ulpi_config->reset_gpio, 0); - phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0); - phy->ulpi->io_priv = regs + ULPI_VIEWPORT; - } else { - err = utmip_pad_open(phy); - if (err < 0) - goto err1; - } + phy->u_phy.init = tegra_phy_init; + phy->u_phy.shutdown = tegra_usb_phy_close; + phy->u_phy.set_suspend = tegra_usb_phy_suspend; return phy; @@ -743,24 +795,6 @@ err0: } EXPORT_SYMBOL_GPL(tegra_usb_phy_open); -int tegra_usb_phy_power_on(struct tegra_usb_phy *phy) -{ - if (phy_is_ulpi(phy)) - return ulpi_phy_power_on(phy); - else - return utmi_phy_power_on(phy); -} -EXPORT_SYMBOL_GPL(tegra_usb_phy_power_on); - -void tegra_usb_phy_power_off(struct tegra_usb_phy *phy) -{ - if (phy_is_ulpi(phy)) - ulpi_phy_power_off(phy); - else - utmi_phy_power_off(phy); -} -EXPORT_SYMBOL_GPL(tegra_usb_phy_power_off); - void tegra_usb_phy_preresume(struct tegra_usb_phy *phy) { if (!phy_is_ulpi(phy)) @@ -803,15 +837,3 @@ void tegra_usb_phy_clk_enable(struct tegra_usb_phy *phy) utmi_phy_clk_enable(phy); } EXPORT_SYMBOL_GPL(tegra_usb_phy_clk_enable); - -void tegra_usb_phy_close(struct tegra_usb_phy *phy) -{ - if (phy_is_ulpi(phy)) - clk_put(phy->clk); - else - utmip_pad_close(phy); - clk_disable_unprepare(phy->pll_u); - clk_put(phy->pll_u); - kfree(phy); -} -EXPORT_SYMBOL_GPL(tegra_usb_phy_close); diff --git a/include/linux/usb/nop-usb-xceiv.h b/include/linux/usb/nop-usb-xceiv.h new file mode 100644 index 000000000000..28884c717411 --- /dev/null +++ b/include/linux/usb/nop-usb-xceiv.h @@ -0,0 +1,24 @@ +#ifndef __LINUX_USB_NOP_XCEIV_H +#define __LINUX_USB_NOP_XCEIV_H + +#include <linux/usb/otg.h> + +struct nop_usb_xceiv_platform_data { + enum usb_phy_type type; +}; + +#if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE)) +/* sometimes transceivers are accessed only through e.g. ULPI */ +extern void usb_nop_xceiv_register(void); +extern void usb_nop_xceiv_unregister(void); +#else +static inline void usb_nop_xceiv_register(void) +{ +} + +static inline void usb_nop_xceiv_unregister(void) +{ +} +#endif + +#endif /* __LINUX_USB_NOP_XCEIV_H */ diff --git a/include/linux/usb/omap_usb.h b/include/linux/usb/omap_usb.h new file mode 100644 index 000000000000..0ea17f8ae820 --- /dev/null +++ b/include/linux/usb/omap_usb.h @@ -0,0 +1,46 @@ +/* + * omap_usb.h -- omap usb2 phy header file + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Kishon Vijay Abraham I <kishon@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __DRIVERS_OMAP_USB2_H +#define __DRIVERS_OMAP_USB2_H + +#include <linux/usb/otg.h> + +struct omap_usb { + struct usb_phy phy; + struct phy_companion *comparator; + struct device *dev; + u32 __iomem *control_dev; + struct clk *wkupclk; + u8 is_suspended:1; +}; + +#define PHY_PD 0x1 + +#define phy_to_omapusb(x) container_of((x), struct omap_usb, phy) + +#if defined(CONFIG_OMAP_USB2) || defined(CONFIG_OMAP_USB2_MODULE) +extern int omap_usb2_set_comparator(struct phy_companion *comparator); +#else +static inline int omap_usb2_set_comparator(struct phy_companion *comparator) +{ + return -ENODEV; +} +#endif + +#endif /* __DRIVERS_OMAP_USB_H */ diff --git a/include/linux/usb/otg.h b/include/linux/usb/otg.h index 45824be0a2f9..e8a5fe87c6bd 100644 --- a/include/linux/usb/otg.h +++ b/include/linux/usb/otg.h @@ -9,56 +9,7 @@ #ifndef __LINUX_USB_OTG_H #define __LINUX_USB_OTG_H -#include <linux/notifier.h> - -/* OTG defines lots of enumeration states before device reset */ -enum usb_otg_state { - OTG_STATE_UNDEFINED = 0, - - /* single-role peripheral, and dual-role default-b */ - OTG_STATE_B_IDLE, - OTG_STATE_B_SRP_INIT, - OTG_STATE_B_PERIPHERAL, - - /* extra dual-role default-b states */ - OTG_STATE_B_WAIT_ACON, - OTG_STATE_B_HOST, - - /* dual-role default-a */ - OTG_STATE_A_IDLE, - OTG_STATE_A_WAIT_VRISE, - OTG_STATE_A_WAIT_BCON, - OTG_STATE_A_HOST, - OTG_STATE_A_SUSPEND, - OTG_STATE_A_PERIPHERAL, - OTG_STATE_A_WAIT_VFALL, - OTG_STATE_A_VBUS_ERR, -}; - -enum usb_phy_events { - USB_EVENT_NONE, /* no events or cable disconnected */ - USB_EVENT_VBUS, /* vbus valid event */ - USB_EVENT_ID, /* id was grounded */ - USB_EVENT_CHARGER, /* usb dedicated charger */ - USB_EVENT_ENUMERATED, /* gadget driver enumerated */ -}; - -/* associate a type with PHY */ -enum usb_phy_type { - USB_PHY_TYPE_UNDEFINED, - USB_PHY_TYPE_USB2, - USB_PHY_TYPE_USB3, -}; - -struct usb_phy; - -/* for transceivers connected thru an ULPI interface, the user must - * provide access ops - */ -struct usb_phy_io_ops { - int (*read)(struct usb_phy *x, u32 reg); - int (*write)(struct usb_phy *x, u32 val, u32 reg); -}; +#include <linux/usb/phy.h> struct usb_otg { u8 default_a; @@ -85,134 +36,9 @@ struct usb_otg { }; -/* - * the otg driver needs to interact with both device side and host side - * usb controllers. it decides which controller is active at a given - * moment, using the transceiver, ID signal, HNP and sometimes static - * configuration information (including "board isn't wired for otg"). - */ -struct usb_phy { - struct device *dev; - const char *label; - unsigned int flags; - - enum usb_phy_type type; - enum usb_otg_state state; - enum usb_phy_events last_event; - - struct usb_otg *otg; - - struct device *io_dev; - struct usb_phy_io_ops *io_ops; - void __iomem *io_priv; - - /* for notification of usb_phy_events */ - struct atomic_notifier_head notifier; - - /* to pass extra port status to the root hub */ - u16 port_status; - u16 port_change; - - /* to support controllers that have multiple transceivers */ - struct list_head head; - - /* initialize/shutdown the OTG controller */ - int (*init)(struct usb_phy *x); - void (*shutdown)(struct usb_phy *x); - - /* effective for B devices, ignored for A-peripheral */ - int (*set_power)(struct usb_phy *x, - unsigned mA); - - /* for non-OTG B devices: set transceiver into suspend mode */ - int (*set_suspend)(struct usb_phy *x, - int suspend); - - /* notify phy connect status change */ - int (*notify_connect)(struct usb_phy *x, int port); - int (*notify_disconnect)(struct usb_phy *x, int port); -}; - - -/* for board-specific init logic */ -extern int usb_add_phy(struct usb_phy *, enum usb_phy_type type); -extern void usb_remove_phy(struct usb_phy *); - -#if defined(CONFIG_NOP_USB_XCEIV) || (defined(CONFIG_NOP_USB_XCEIV_MODULE) && defined(MODULE)) -/* sometimes transceivers are accessed only through e.g. ULPI */ -extern void usb_nop_xceiv_register(void); -extern void usb_nop_xceiv_unregister(void); -#else -static inline void usb_nop_xceiv_register(void) -{ -} - -static inline void usb_nop_xceiv_unregister(void) -{ -} -#endif - -/* helpers for direct access thru low-level io interface */ -static inline int usb_phy_io_read(struct usb_phy *x, u32 reg) -{ - if (x->io_ops && x->io_ops->read) - return x->io_ops->read(x, reg); - - return -EINVAL; -} - -static inline int usb_phy_io_write(struct usb_phy *x, u32 val, u32 reg) -{ - if (x->io_ops && x->io_ops->write) - return x->io_ops->write(x, val, reg); - - return -EINVAL; -} - -static inline int -usb_phy_init(struct usb_phy *x) -{ - if (x->init) - return x->init(x); - - return 0; -} - -static inline void -usb_phy_shutdown(struct usb_phy *x) -{ - if (x->shutdown) - x->shutdown(x); -} - -/* for usb host and peripheral controller drivers */ #ifdef CONFIG_USB_OTG_UTILS -extern struct usb_phy *usb_get_phy(enum usb_phy_type type); -extern struct usb_phy *devm_usb_get_phy(struct device *dev, - enum usb_phy_type type); -extern void usb_put_phy(struct usb_phy *); -extern void devm_usb_put_phy(struct device *dev, struct usb_phy *x); extern const char *otg_state_string(enum usb_otg_state state); #else -static inline struct usb_phy *usb_get_phy(enum usb_phy_type type) -{ - return NULL; -} - -static inline struct usb_phy *devm_usb_get_phy(struct device *dev, - enum usb_phy_type type) -{ - return NULL; -} - -static inline void usb_put_phy(struct usb_phy *x) -{ -} - -static inline void devm_usb_put_phy(struct device *dev, struct usb_phy *x) -{ -} - static inline const char *otg_state_string(enum usb_otg_state state) { return NULL; @@ -262,42 +88,6 @@ otg_set_peripheral(struct usb_otg *otg, struct usb_gadget *periph) } static inline int -usb_phy_set_power(struct usb_phy *x, unsigned mA) -{ - if (x && x->set_power) - return x->set_power(x, mA); - return 0; -} - -/* Context: can sleep */ -static inline int -usb_phy_set_suspend(struct usb_phy *x, int suspend) -{ - if (x->set_suspend != NULL) - return x->set_suspend(x, suspend); - else - return 0; -} - -static inline int -usb_phy_notify_connect(struct usb_phy *x, int port) -{ - if (x->notify_connect) - return x->notify_connect(x, port); - else - return 0; -} - -static inline int -usb_phy_notify_disconnect(struct usb_phy *x, int port) -{ - if (x->notify_disconnect) - return x->notify_disconnect(x, port); - else - return 0; -} - -static inline int otg_start_srp(struct usb_otg *otg) { if (otg && otg->start_srp) @@ -306,31 +96,7 @@ otg_start_srp(struct usb_otg *otg) return -ENOTSUPP; } -/* notifiers */ -static inline int -usb_register_notifier(struct usb_phy *x, struct notifier_block *nb) -{ - return atomic_notifier_chain_register(&x->notifier, nb); -} - -static inline void -usb_unregister_notifier(struct usb_phy *x, struct notifier_block *nb) -{ - atomic_notifier_chain_unregister(&x->notifier, nb); -} - /* for OTG controller drivers (and maybe other stuff) */ extern int usb_bus_start_enum(struct usb_bus *bus, unsigned port_num); -static inline const char *usb_phy_type_string(enum usb_phy_type type) -{ - switch (type) { - case USB_PHY_TYPE_USB2: - return "USB2 PHY"; - case USB_PHY_TYPE_USB3: - return "USB3 PHY"; - default: - return "UNKNOWN PHY TYPE"; - } -} #endif /* __LINUX_USB_OTG_H */ diff --git a/include/linux/usb/phy.h b/include/linux/usb/phy.h new file mode 100644 index 000000000000..06b5bae35b29 --- /dev/null +++ b/include/linux/usb/phy.h @@ -0,0 +1,233 @@ +/* USB OTG (On The Go) defines */ +/* + * + * These APIs may be used between USB controllers. USB device drivers + * (for either host or peripheral roles) don't use these calls; they + * continue to use just usb_device and usb_gadget. + */ + +#ifndef __LINUX_USB_PHY_H +#define __LINUX_USB_PHY_H + +#include <linux/notifier.h> + +enum usb_phy_events { + USB_EVENT_NONE, /* no events or cable disconnected */ + USB_EVENT_VBUS, /* vbus valid event */ + USB_EVENT_ID, /* id was grounded */ + USB_EVENT_CHARGER, /* usb dedicated charger */ + USB_EVENT_ENUMERATED, /* gadget driver enumerated */ +}; + +/* associate a type with PHY */ +enum usb_phy_type { + USB_PHY_TYPE_UNDEFINED, + USB_PHY_TYPE_USB2, + USB_PHY_TYPE_USB3, +}; + +/* OTG defines lots of enumeration states before device reset */ +enum usb_otg_state { + OTG_STATE_UNDEFINED = 0, + + /* single-role peripheral, and dual-role default-b */ + OTG_STATE_B_IDLE, + OTG_STATE_B_SRP_INIT, + OTG_STATE_B_PERIPHERAL, + + /* extra dual-role default-b states */ + OTG_STATE_B_WAIT_ACON, + OTG_STATE_B_HOST, + + /* dual-role default-a */ + OTG_STATE_A_IDLE, + OTG_STATE_A_WAIT_VRISE, + OTG_STATE_A_WAIT_BCON, + OTG_STATE_A_HOST, + OTG_STATE_A_SUSPEND, + OTG_STATE_A_PERIPHERAL, + OTG_STATE_A_WAIT_VFALL, + OTG_STATE_A_VBUS_ERR, +}; + +struct usb_phy; +struct usb_otg; + +/* for transceivers connected thru an ULPI interface, the user must + * provide access ops + */ +struct usb_phy_io_ops { + int (*read)(struct usb_phy *x, u32 reg); + int (*write)(struct usb_phy *x, u32 val, u32 reg); +}; + +struct usb_phy { + struct device *dev; + const char *label; + unsigned int flags; + + enum usb_phy_type type; + enum usb_otg_state state; + enum usb_phy_events last_event; + + struct usb_otg *otg; + + struct device *io_dev; + struct usb_phy_io_ops *io_ops; + void __iomem *io_priv; + + /* for notification of usb_phy_events */ + struct atomic_notifier_head notifier; + + /* to pass extra port status to the root hub */ + u16 port_status; + u16 port_change; + + /* to support controllers that have multiple transceivers */ + struct list_head head; + + /* initialize/shutdown the OTG controller */ + int (*init)(struct usb_phy *x); + void (*shutdown)(struct usb_phy *x); + + /* effective for B devices, ignored for A-peripheral */ + int (*set_power)(struct usb_phy *x, + unsigned mA); + + /* for non-OTG B devices: set transceiver into suspend mode */ + int (*set_suspend)(struct usb_phy *x, + int suspend); + + /* notify phy connect status change */ + int (*notify_connect)(struct usb_phy *x, int port); + int (*notify_disconnect)(struct usb_phy *x, int port); +}; + + +/* for board-specific init logic */ +extern int usb_add_phy(struct usb_phy *, enum usb_phy_type type); +extern void usb_remove_phy(struct usb_phy *); + +/* helpers for direct access thru low-level io interface */ +static inline int usb_phy_io_read(struct usb_phy *x, u32 reg) +{ + if (x->io_ops && x->io_ops->read) + return x->io_ops->read(x, reg); + + return -EINVAL; +} + +static inline int usb_phy_io_write(struct usb_phy *x, u32 val, u32 reg) +{ + if (x->io_ops && x->io_ops->write) + return x->io_ops->write(x, val, reg); + + return -EINVAL; +} + +static inline int +usb_phy_init(struct usb_phy *x) +{ + if (x->init) + return x->init(x); + + return 0; +} + +static inline void +usb_phy_shutdown(struct usb_phy *x) +{ + if (x->shutdown) + x->shutdown(x); +} + +/* for usb host and peripheral controller drivers */ +#ifdef CONFIG_USB_OTG_UTILS +extern struct usb_phy *usb_get_phy(enum usb_phy_type type); +extern struct usb_phy *devm_usb_get_phy(struct device *dev, + enum usb_phy_type type); +extern void usb_put_phy(struct usb_phy *); +extern void devm_usb_put_phy(struct device *dev, struct usb_phy *x); +#else +static inline struct usb_phy *usb_get_phy(enum usb_phy_type type) +{ + return NULL; +} + +static inline struct usb_phy *devm_usb_get_phy(struct device *dev, + enum usb_phy_type type) +{ + return NULL; +} + +static inline void usb_put_phy(struct usb_phy *x) +{ +} + +static inline void devm_usb_put_phy(struct device *dev, struct usb_phy *x) +{ +} + +#endif + +static inline int +usb_phy_set_power(struct usb_phy *x, unsigned mA) +{ + if (x && x->set_power) + return x->set_power(x, mA); + return 0; +} + +/* Context: can sleep */ +static inline int +usb_phy_set_suspend(struct usb_phy *x, int suspend) +{ + if (x->set_suspend != NULL) + return x->set_suspend(x, suspend); + else + return 0; +} + +static inline int +usb_phy_notify_connect(struct usb_phy *x, int port) +{ + if (x->notify_connect) + return x->notify_connect(x, port); + else + return 0; +} + +static inline int +usb_phy_notify_disconnect(struct usb_phy *x, int port) +{ + if (x->notify_disconnect) + return x->notify_disconnect(x, port); + else + return 0; +} + +/* notifiers */ +static inline int +usb_register_notifier(struct usb_phy *x, struct notifier_block *nb) +{ + return atomic_notifier_chain_register(&x->notifier, nb); +} + +static inline void +usb_unregister_notifier(struct usb_phy *x, struct notifier_block *nb) +{ + atomic_notifier_chain_unregister(&x->notifier, nb); +} + +static inline const char *usb_phy_type_string(enum usb_phy_type type) +{ + switch (type) { + case USB_PHY_TYPE_USB2: + return "USB2 PHY"; + case USB_PHY_TYPE_USB3: + return "USB3 PHY"; + default: + return "UNKNOWN PHY TYPE"; + } +} +#endif /* __LINUX_USB_PHY_H */ diff --git a/include/linux/usb/phy_companion.h b/include/linux/usb/phy_companion.h new file mode 100644 index 000000000000..edd2ec23d282 --- /dev/null +++ b/include/linux/usb/phy_companion.h @@ -0,0 +1,34 @@ +/* + * phy-companion.h -- phy companion to indicate the comparator part of PHY + * + * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * Author: Kishon Vijay Abraham I <kishon@ti.com> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __DRIVERS_PHY_COMPANION_H +#define __DRIVERS_PHY_COMPANION_H + +#include <linux/usb/otg.h> + +/* phy_companion to take care of VBUS, ID and srp capabilities */ +struct phy_companion { + + /* effective for A-peripheral, ignored for B devices */ + int (*set_vbus)(struct phy_companion *x, bool enabled); + + /* for B devices only: start session with A-Host */ + int (*start_srp)(struct phy_companion *x); +}; + +#endif /* __DRIVERS_PHY_COMPANION_H */ diff --git a/arch/arm/mach-tegra/include/mach/usb_phy.h b/include/linux/usb/tegra_usb_phy.h index 935ce9f65590..176b1ca06ae4 100644 --- a/arch/arm/mach-tegra/include/mach/usb_phy.h +++ b/include/linux/usb/tegra_usb_phy.h @@ -1,6 +1,4 @@ /* - * arch/arm/mach-tegra/include/mach/usb_phy.h - * * Copyright (C) 2010 Google, Inc. * * This software is licensed under the terms of the GNU General Public @@ -14,8 +12,8 @@ * */ -#ifndef __MACH_USB_PHY_H -#define __MACH_USB_PHY_H +#ifndef __TEGRA_USB_PHY_H +#define __TEGRA_USB_PHY_H #include <linux/clk.h> #include <linux/usb/otg.h> @@ -59,19 +57,17 @@ struct tegra_usb_phy { enum tegra_usb_phy_mode mode; void *config; struct usb_phy *ulpi; + struct usb_phy u_phy; + struct device *dev; }; struct tegra_usb_phy *tegra_usb_phy_open(struct device *dev, int instance, void __iomem *regs, void *config, enum tegra_usb_phy_mode phy_mode); -int tegra_usb_phy_power_on(struct tegra_usb_phy *phy); - void tegra_usb_phy_clk_disable(struct tegra_usb_phy *phy); void tegra_usb_phy_clk_enable(struct tegra_usb_phy *phy); -void tegra_usb_phy_power_off(struct tegra_usb_phy *phy); - void tegra_usb_phy_preresume(struct tegra_usb_phy *phy); void tegra_usb_phy_postresume(struct tegra_usb_phy *phy); @@ -81,6 +77,4 @@ void tegra_ehci_phy_restore_start(struct tegra_usb_phy *phy, void tegra_ehci_phy_restore_end(struct tegra_usb_phy *phy); -void tegra_usb_phy_close(struct tegra_usb_phy *phy); - -#endif /* __MACH_USB_PHY_H */ +#endif /* __TEGRA_USB_PHY_H */ |