diff options
| -rw-r--r-- | Documentation/kernel-parameters.txt | 6 | ||||
| -rw-r--r-- | drivers/phy/phy-rockchip-usb.c | 233 |
2 files changed, 203 insertions, 36 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 87d40a72f6a1..d91417b6c88e 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -3486,6 +3486,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. ro [KNL] Mount root device read-only on boot + rockchip.usb_uart + Enable the uart passthrough on the designated usb port + on Rockchip SoCs. When active, the signals of the + debug-uart get routed to the D+ and D- pins of the usb + port and the regular usb controller gets disabled. + root= [KNL] Root filesystem See name_to_dev_t comment in init/do_mounts.c. diff --git a/drivers/phy/phy-rockchip-usb.c b/drivers/phy/phy-rockchip-usb.c index 33a80eba1cb4..f62d899063a3 100644 --- a/drivers/phy/phy-rockchip-usb.c +++ b/drivers/phy/phy-rockchip-usb.c @@ -30,21 +30,23 @@ #include <linux/regmap.h> #include <linux/mfd/syscon.h> -/* - * The higher 16-bit of this register is used for write protection - * only if BIT(13 + 16) set to 1 the BIT(13) can be written. - */ -#define SIDDQ_WRITE_ENA BIT(29) -#define SIDDQ_ON BIT(13) -#define SIDDQ_OFF (0 << 13) +static int enable_usb_uart; + +#define HIWORD_UPDATE(val, mask) \ + ((val) | (mask) << 16) + +#define UOC_CON0_SIDDQ BIT(13) struct rockchip_usb_phys { int reg; const char *pll_name; }; +struct rockchip_usb_phy_base; struct rockchip_usb_phy_pdata { struct rockchip_usb_phys *phys; + int (*init_usb_uart)(struct regmap *grf); + int usb_uart_phy; }; struct rockchip_usb_phy_base { @@ -61,13 +63,15 @@ struct rockchip_usb_phy { struct clk *clk480m; struct clk_hw clk480m_hw; struct phy *phy; + bool uart_enabled; }; static int rockchip_usb_phy_power(struct rockchip_usb_phy *phy, bool siddq) { - return regmap_write(phy->base->reg_base, phy->reg_offset, - SIDDQ_WRITE_ENA | (siddq ? SIDDQ_ON : SIDDQ_OFF)); + u32 val = HIWORD_UPDATE(siddq ? UOC_CON0_SIDDQ : 0, UOC_CON0_SIDDQ); + + return regmap_write(phy->base->reg_base, phy->reg_offset, val); } static unsigned long rockchip_usb_phy480m_recalc_rate(struct clk_hw *hw, @@ -108,7 +112,7 @@ static int rockchip_usb_phy480m_is_enabled(struct clk_hw *hw) if (ret < 0) return ret; - return (val & SIDDQ_ON) ? 0 : 1; + return (val & UOC_CON0_SIDDQ) ? 0 : 1; } static const struct clk_ops rockchip_usb_phy480m_ops = { @@ -122,6 +126,9 @@ static int rockchip_usb_phy_power_off(struct phy *_phy) { struct rockchip_usb_phy *phy = phy_get_drvdata(_phy); + if (phy->uart_enabled) + return -EBUSY; + clk_disable_unprepare(phy->clk480m); return 0; @@ -131,6 +138,9 @@ static int rockchip_usb_phy_power_on(struct phy *_phy) { struct rockchip_usb_phy *phy = phy_get_drvdata(_phy); + if (phy->uart_enabled) + return -EBUSY; + return clk_prepare_enable(phy->clk480m); } @@ -144,8 +154,10 @@ static void rockchip_usb_phy_action(void *data) { struct rockchip_usb_phy *rk_phy = data; - of_clk_del_provider(rk_phy->np); - clk_unregister(rk_phy->clk480m); + if (!rk_phy->uart_enabled) { + of_clk_del_provider(rk_phy->np); + clk_unregister(rk_phy->clk480m); + } if (rk_phy->clk) clk_put(rk_phy->clk); @@ -194,30 +206,35 @@ static int rockchip_usb_phy_init(struct rockchip_usb_phy_base *base, return -EINVAL; } - if (rk_phy->clk) { - clk_name = __clk_get_name(rk_phy->clk); - init.flags = 0; - init.parent_names = &clk_name; - init.num_parents = 1; + if (enable_usb_uart && base->pdata->usb_uart_phy == i) { + dev_dbg(base->dev, "phy%d used as uart output\n", i); + rk_phy->uart_enabled = true; } else { - init.flags = CLK_IS_ROOT; - init.parent_names = NULL; - init.num_parents = 0; - } + if (rk_phy->clk) { + clk_name = __clk_get_name(rk_phy->clk); + init.flags = 0; + init.parent_names = &clk_name; + init.num_parents = 1; + } else { + init.flags = CLK_IS_ROOT; + init.parent_names = NULL; + init.num_parents = 0; + } - init.ops = &rockchip_usb_phy480m_ops; - rk_phy->clk480m_hw.init = &init; + init.ops = &rockchip_usb_phy480m_ops; + rk_phy->clk480m_hw.init = &init; - rk_phy->clk480m = clk_register(base->dev, &rk_phy->clk480m_hw); - if (IS_ERR(rk_phy->clk480m)) { - err = PTR_ERR(rk_phy->clk480m); - goto err_clk; - } + rk_phy->clk480m = clk_register(base->dev, &rk_phy->clk480m_hw); + if (IS_ERR(rk_phy->clk480m)) { + err = PTR_ERR(rk_phy->clk480m); + goto err_clk; + } - err = of_clk_add_provider(child, of_clk_src_simple_get, - rk_phy->clk480m); - if (err < 0) - goto err_clk_prov; + err = of_clk_add_provider(child, of_clk_src_simple_get, + rk_phy->clk480m); + if (err < 0) + goto err_clk_prov; + } err = devm_add_action(base->dev, rockchip_usb_phy_action, rk_phy); if (err) @@ -230,13 +247,21 @@ static int rockchip_usb_phy_init(struct rockchip_usb_phy_base *base, } phy_set_drvdata(rk_phy->phy, rk_phy); - /* only power up usb phy when it use, so disable it when init*/ - return rockchip_usb_phy_power(rk_phy, 1); + /* + * When acting as uart-pipe, just keep clock on otherwise + * only power up usb phy when it use, so disable it when init + */ + if (rk_phy->uart_enabled) + return clk_prepare_enable(rk_phy->clk); + else + return rockchip_usb_phy_power(rk_phy, 1); err_devm_action: - of_clk_del_provider(child); + if (!rk_phy->uart_enabled) + of_clk_del_provider(child); err_clk_prov: - clk_unregister(rk_phy->clk480m); + if (!rk_phy->uart_enabled) + clk_unregister(rk_phy->clk480m); err_clk: if (rk_phy->clk) clk_put(rk_phy->clk); @@ -259,6 +284,86 @@ static const struct rockchip_usb_phy_pdata rk3188_pdata = { }, }; +#define RK3288_UOC0_CON0 0x320 +#define RK3288_UOC0_CON0_COMMON_ON_N BIT(0) +#define RK3288_UOC0_CON0_DISABLE BIT(4) + +#define RK3288_UOC0_CON2 0x328 +#define RK3288_UOC0_CON2_SOFT_CON_SEL BIT(2) + +#define RK3288_UOC0_CON3 0x32c +#define RK3288_UOC0_CON3_UTMI_SUSPENDN BIT(0) +#define RK3288_UOC0_CON3_UTMI_OPMODE_NODRIVING (1 << 1) +#define RK3288_UOC0_CON3_UTMI_OPMODE_MASK (3 << 1) +#define RK3288_UOC0_CON3_UTMI_XCVRSEELCT_FSTRANSC (1 << 3) +#define RK3288_UOC0_CON3_UTMI_XCVRSEELCT_MASK (3 << 3) +#define RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED BIT(5) +#define RK3288_UOC0_CON3_BYPASSDMEN BIT(6) +#define RK3288_UOC0_CON3_BYPASSSEL BIT(7) + +/* + * Enable the bypass of uart2 data through the otg usb phy. + * Original description in the TRM. + * 1. Disable the OTG block by setting OTGDISABLE0 to 1’b1. + * 2. Disable the pull-up resistance on the D+ line by setting + * OPMODE0[1:0] to 2’b01. + * 3. To ensure that the XO, Bias, and PLL blocks are powered down in Suspend + * mode, set COMMONONN to 1’b1. + * 4. Place the USB PHY in Suspend mode by setting SUSPENDM0 to 1’b0. + * 5. Set BYPASSSEL0 to 1’b1. + * 6. To transmit data, controls BYPASSDMEN0, and BYPASSDMDATA0. + * To receive data, monitor FSVPLUS0. + * + * The actual code in the vendor kernel does some things differently. + */ +static int __init rk3288_init_usb_uart(struct regmap *grf) +{ + u32 val; + int ret; + + /* + * COMMON_ON and DISABLE settings are described in the TRM, + * but were not present in the original code. + * Also disable the analog phy components to save power. + */ + val = HIWORD_UPDATE(RK3288_UOC0_CON0_COMMON_ON_N + | RK3288_UOC0_CON0_DISABLE + | UOC_CON0_SIDDQ, + RK3288_UOC0_CON0_COMMON_ON_N + | RK3288_UOC0_CON0_DISABLE + | UOC_CON0_SIDDQ); + ret = regmap_write(grf, RK3288_UOC0_CON0, val); + if (ret) + return ret; + + val = HIWORD_UPDATE(RK3288_UOC0_CON2_SOFT_CON_SEL, + RK3288_UOC0_CON2_SOFT_CON_SEL); + ret = regmap_write(grf, RK3288_UOC0_CON2, val); + if (ret) + return ret; + + val = HIWORD_UPDATE(RK3288_UOC0_CON3_UTMI_OPMODE_NODRIVING + | RK3288_UOC0_CON3_UTMI_XCVRSEELCT_FSTRANSC + | RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED, + RK3288_UOC0_CON3_UTMI_SUSPENDN + | RK3288_UOC0_CON3_UTMI_OPMODE_MASK + | RK3288_UOC0_CON3_UTMI_XCVRSEELCT_MASK + | RK3288_UOC0_CON3_UTMI_TERMSEL_FULLSPEED); + ret = regmap_write(grf, RK3288_UOC0_CON3, val); + if (ret) + return ret; + + val = HIWORD_UPDATE(RK3288_UOC0_CON3_BYPASSSEL + | RK3288_UOC0_CON3_BYPASSDMEN, + RK3288_UOC0_CON3_BYPASSSEL + | RK3288_UOC0_CON3_BYPASSDMEN); + ret = regmap_write(grf, RK3288_UOC0_CON3, val); + if (ret) + return ret; + + return 0; +} + static const struct rockchip_usb_phy_pdata rk3288_pdata = { .phys = (struct rockchip_usb_phys[]){ { .reg = 0x320, .pll_name = "sclk_otgphy0_480m" }, @@ -266,6 +371,8 @@ static const struct rockchip_usb_phy_pdata rk3288_pdata = { { .reg = 0x348, .pll_name = "sclk_otgphy2_480m" }, { /* sentinel */ } }, + .init_usb_uart = rk3288_init_usb_uart, + .usb_uart_phy = 0, }; static int rockchip_usb_phy_probe(struct platform_device *pdev) @@ -328,6 +435,60 @@ static struct platform_driver rockchip_usb_driver = { module_platform_driver(rockchip_usb_driver); +#ifndef MODULE +static int __init rockchip_init_usb_uart(void) +{ + const struct of_device_id *match; + const struct rockchip_usb_phy_pdata *data; + struct device_node *np; + struct regmap *grf; + int ret; + + if (!enable_usb_uart) + return 0; + + np = of_find_matching_node_and_match(NULL, rockchip_usb_phy_dt_ids, + &match); + if (!np) { + pr_err("%s: failed to find usbphy node\n", __func__); + return -ENOTSUPP; + } + + pr_debug("%s: using settings for %s\n", __func__, match->compatible); + data = match->data; + + if (!data->init_usb_uart) { + pr_err("%s: usb-uart not available on %s\n", + __func__, match->compatible); + return -ENOTSUPP; + } + + grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); + if (IS_ERR(grf)) { + pr_err("%s: Missing rockchip,grf property, %lu\n", + __func__, PTR_ERR(grf)); + return PTR_ERR(grf); + } + + ret = data->init_usb_uart(grf); + if (ret) { + pr_err("%s: could not init usb_uart, %d\n", __func__, ret); + enable_usb_uart = 0; + return ret; + } + + return 0; +} +early_initcall(rockchip_init_usb_uart); + +static int __init rockchip_usb_uart(char *buf) +{ + enable_usb_uart = true; + return 0; +} +early_param("rockchip.usb_uart", rockchip_usb_uart); +#endif + MODULE_AUTHOR("Yunzhi Li <lyz@rock-chips.com>"); MODULE_DESCRIPTION("Rockchip USB 2.0 PHY driver"); MODULE_LICENSE("GPL v2"); |