diff options
Diffstat (limited to 'Documentation/devicetree/bindings/c6x/dscr.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/c6x/dscr.txt | 127 |
1 files changed, 0 insertions, 127 deletions
diff --git a/Documentation/devicetree/bindings/c6x/dscr.txt b/Documentation/devicetree/bindings/c6x/dscr.txt deleted file mode 100644 index 92672235de57..000000000000 --- a/Documentation/devicetree/bindings/c6x/dscr.txt +++ /dev/null @@ -1,127 +0,0 @@ -Device State Configuration Registers ------------------------------------- - -TI C6X SoCs contain a region of miscellaneous registers which provide various -function for SoC control or status. Details vary considerably among from SoC -to SoC with no two being alike. - -In general, the Device State Configuration Registers (DSCR) will provide one or -more configuration registers often protected by a lock register where one or -more key values must be written to a lock register in order to unlock the -configuration register for writes. These configuration register may be used to -enable (and disable in some cases) SoC pin drivers, select peripheral clock -sources (internal or pin), etc. In some cases, a configuration register is -write once or the individual bits are write once. In addition to device config, -the DSCR block may provide registers which are used to reset peripherals, -provide device ID information, provide ethernet MAC addresses, as well as other -miscellaneous functions. - -For device state control (enable/disable), each device control is assigned an -id which is used by individual device drivers to control the state as needed. - -Required properties: - -- compatible: must be "ti,c64x+dscr" -- reg: register area base and size - -Optional properties: - - NOTE: These are optional in that not all SoCs will have all properties. For - SoCs which do support a given property, leaving the property out of the - device tree will result in reduced functionality or possibly driver - failure. - -- ti,dscr-devstat - offset of the devstat register - -- ti,dscr-silicon-rev - offset, start bit, and bitsize of silicon revision field - -- ti,dscr-rmii-resets - offset and bitmask of RMII reset field. May have multiple tuples if more - than one ethernet port is available. - -- ti,dscr-locked-regs - possibly multiple tuples describing registers which are write protected by - a lock register. Each tuple consists of the register offset, lock register - offsset, and the key value used to unlock the register. - -- ti,dscr-kick-regs - offset and key values of two "kick" registers used to write protect other - registers in DSCR. On SoCs using kick registers, the first key must be - written to the first kick register and the second key must be written to - the second register before other registers in the area are write-enabled. - -- ti,dscr-mac-fuse-regs - MAC addresses are contained in two registers. Each element of a MAC address - is contained in a single byte. This property has two tuples. Each tuple has - a register offset and four cells representing bytes in the register from - most significant to least. The value of these four cells is the MAC byte - index (1-6) of the byte within the register. A value of 0 means the byte - is unused in the MAC address. - -- ti,dscr-devstate-ctl-regs - This property describes the bitfields used to control the state of devices. - Each tuple describes a range of identical bitfields used to control one or - more devices (one bitfield per device). The layout of each tuple is: - - start_id num_ids reg enable disable start_bit nbits - - Where: - start_id is device id for the first device control in the range - num_ids is the number of device controls in the range - reg is the offset of the register holding the control bits - enable is the value to enable a device - disable is the value to disable a device (0xffffffff if cannot disable) - start_bit is the bit number of the first bit in the range - nbits is the number of bits per device control - -- ti,dscr-devstate-stat-regs - This property describes the bitfields used to provide device state status - for device states controlled by the DSCR. Each tuple describes a range of - identical bitfields used to provide status for one or more devices (one - bitfield per device). The layout of each tuple is: - - start_id num_ids reg enable disable start_bit nbits - - Where: - start_id is device id for the first device status in the range - num_ids is the number of devices covered by the range - reg is the offset of the register holding the status bits - enable is the value indicating device is enabled - disable is the value indicating device is disabled - start_bit is the bit number of the first bit in the range - nbits is the number of bits per device status - -- ti,dscr-privperm - Offset and default value for register used to set access privilege for - some SoC devices. - - -Example: - - device-state-config-regs@2a80000 { - compatible = "ti,c64x+dscr"; - reg = <0x02a80000 0x41000>; - - ti,dscr-devstat = <0>; - ti,dscr-silicon-rev = <8 28 0xf>; - ti,dscr-rmii-resets = <0x40020 0x00040000>; - - ti,dscr-locked-regs = <0x40008 0x40004 0x0f0a0b00>; - ti,dscr-devstate-ctl-regs = - <0 12 0x40008 1 0 0 2 - 12 1 0x40008 3 0 30 2 - 13 2 0x4002c 1 0xffffffff 0 1>; - ti,dscr-devstate-stat-regs = - <0 10 0x40014 1 0 0 3 - 10 2 0x40018 1 0 0 3>; - - ti,dscr-mac-fuse-regs = <0x700 1 2 3 4 - 0x704 5 6 0 0>; - - ti,dscr-privperm = <0x41c 0xaaaaaaaa>; - - ti,dscr-kick-regs = <0x38 0x83E70B13 - 0x3c 0x95A4F1E0>; - }; |