diff options
Diffstat (limited to 'Documentation/devicetree/bindings/leds/backlight')
8 files changed, 244 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt b/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt new file mode 100644 index 000000000000..261df2799315 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/88pm860x.txt @@ -0,0 +1,15 @@ +88pm860x-backlight bindings + +Optional properties: + - marvell,88pm860x-iset: Current supplies on backlight device. + - marvell,88pm860x-pwm: PWM frequency on backlight device. + +Example: + + backlights { + backlight-0 { + marvell,88pm860x-iset = <4>; + marvell,88pm860x-pwm = <3>; + }; + backlight-2 { + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt new file mode 100644 index 000000000000..321be6640533 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/gpio-backlight.txt @@ -0,0 +1,16 @@ +gpio-backlight bindings + +Required properties: + - compatible: "gpio-backlight" + - gpios: describes the gpio that is used for enabling/disabling the backlight. + refer to bindings/gpio/gpio.txt for more details. + +Optional properties: + - default-on: enable the backlight at boot. + +Example: + backlight { + compatible = "gpio-backlight"; + gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + default-on; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/lp855x.txt b/Documentation/devicetree/bindings/leds/backlight/lp855x.txt new file mode 100644 index 000000000000..0a3ecbc3a1b9 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/lp855x.txt @@ -0,0 +1,70 @@ +lp855x bindings + +Required properties: + - compatible: "ti,lp8550", "ti,lp8551", "ti,lp8552", "ti,lp8553", + "ti,lp8555", "ti,lp8556", "ti,lp8557" + - reg: I2C slave address (u8) + - dev-ctrl: Value of DEVICE CONTROL register (u8). It depends on the device. + +Optional properties: + - bl-name: Backlight device name (string) + - init-brt: Initial value of backlight brightness (u8) + - pwm-period: PWM period value. Set only PWM input mode used (u32) + - rom-addr: Register address of ROM area to be updated (u8) + - rom-val: Register value to be updated (u8) + - power-supply: Regulator which controls the 3V rail + +Example: + + /* LP8555 */ + backlight@2c { + compatible = "ti,lp8555"; + reg = <0x2c>; + + dev-ctrl = /bits/ 8 <0x00>; + pwm-period = <10000>; + + /* 4V OV, 4 output LED0 string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + + /* Heavy smoothing, 24ms ramp time step */ + rom_15h { + rom-addr = /bits/ 8 <0x15>; + rom-val = /bits/ 8 <0xc7>; + }; + + /* 4 output LED1 string enabled */ + rom_19h { + rom-addr = /bits/ 8 <0x19>; + rom-val = /bits/ 8 <0x0f>; + }; + }; + + /* LP8556 */ + backlight@2c { + compatible = "ti,lp8556"; + reg = <0x2c>; + + bl-name = "lcd-bl"; + dev-ctrl = /bits/ 8 <0x85>; + init-brt = /bits/ 8 <0x10>; + }; + + /* LP8557 */ + backlight@2c { + compatible = "ti,lp8557"; + reg = <0x2c>; + power-supply = <&backlight_vdd>; + + dev-ctrl = /bits/ 8 <0x41>; + init-brt = /bits/ 8 <0x0a>; + + /* 4V OV, 4 output LED string enabled */ + rom_14h { + rom-addr = /bits/ 8 <0x14>; + rom-val = /bits/ 8 <0xcf>; + }; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt new file mode 100644 index 000000000000..b4cffdaa4137 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/max8925-backlight.txt @@ -0,0 +1,10 @@ +88pm860x-backlight bindings + +Optional properties: + - maxim,max8925-dual-string: whether support dual string + +Example: + + backlights { + maxim,max8925-dual-string = <0>; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt b/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt new file mode 100644 index 000000000000..e5b294dafc58 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/pm8941-wled.txt @@ -0,0 +1,42 @@ +Binding for Qualcomm PM8941 WLED driver + +Required properties: +- compatible: should be "qcom,pm8941-wled" +- reg: slave address + +Optional properties: +- default-brightness: brightness value on boot, value from: 0-4095 + default: 2048 +- label: The name of the backlight device +- qcom,cs-out: bool; enable current sink output +- qcom,cabc: bool; enable content adaptive backlight control +- qcom,ext-gen: bool; use externally generated modulator signal to dim +- qcom,current-limit: mA; per-string current limit; value from 0 to 25 + default: 20mA +- qcom,current-boost-limit: mA; boost current limit; one of: + 105, 385, 525, 805, 980, 1260, 1400, 1680 + default: 805mA +- qcom,switching-freq: kHz; switching frequency; one of: + 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, + 1600, 1920, 2400, 3200, 4800, 9600, + default: 1600kHz +- qcom,ovp: V; Over-voltage protection limit; one of: + 27, 29, 32, 35 + default: 29V +- qcom,num-strings: #; number of led strings attached; value from 1 to 3 + default: 2 + +Example: + +pm8941-wled@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; +}; diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt new file mode 100644 index 000000000000..764db86d441a --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.txt @@ -0,0 +1,35 @@ +pwm-backlight bindings + +Required properties: + - compatible: "pwm-backlight" + - pwms: OF device-tree PWM specification (see PWM binding[0]) + - brightness-levels: Array of distinct brightness levels. Typically these + are in the range from 0 to 255, but any range starting at 0 will do. + The actual brightness level (PWM duty cycle) will be interpolated + from these values. 0 means a 0% duty cycle (darkest/off), while the + last value in the array represents a 100% duty cycle (brightest). + - default-brightness-level: the default brightness level (index into the + array defined by the "brightness-levels" property) + - power-supply: regulator for supply voltage + +Optional properties: + - pwm-names: a list of names for the PWM devices specified in the + "pwms" property (see PWM binding[0]) + - enable-gpios: contains a single GPIO specifier for the GPIO which enables + and disables the backlight (see GPIO binding[1]) + +[0]: Documentation/devicetree/bindings/pwm/pwm.txt +[1]: Documentation/devicetree/bindings/gpio/gpio.txt + +Example: + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 0 5000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + + power-supply = <&vdd_bl_reg>; + enable-gpios = <&gpio 58 0>; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt new file mode 100644 index 000000000000..8bf2940f54bc --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/sky81452-backlight.txt @@ -0,0 +1,29 @@ +SKY81452-backlight bindings + +Required properties: +- compatible : Must be "skyworks,sky81452-backlight" + +Optional properties: +- name : Name of backlight device. Default is 'lcd-backlight'. +- gpios : GPIO to use to EN pin. + See Documentation/devicetree/bindings/gpio/gpio.txt +- led-sources : List of enabled channels from 0 to 5. + See Documentation/devicetree/bindings/leds/common.txt +- skyworks,ignore-pwm : Ignore both PWM input +- skyworks,dpwm-mode : Enable DPWM dimming mode, otherwise Analog dimming. +- skyworks,phase-shift : Enable phase shift mode +- skyworks,short-detection-threshold-volt + : It should be one of 4, 5, 6 and 7V. +- skyworks,current-limit-mA + : It should be 2300mA or 2750mA. + +Example: + + backlight { + compatible = "skyworks,sky81452-backlight"; + name = "pwm-backlight"; + led-sources = <0 1 2 5>; + skyworks,ignore-pwm; + skyworks,phase-shift; + skyworks,current-limit-mA = <2300>; + }; diff --git a/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt b/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt new file mode 100644 index 000000000000..5fb9279ac287 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/tps65217-backlight.txt @@ -0,0 +1,27 @@ +TPS65217 family of regulators + +The TPS65217 chip contains a boost converter and current sinks which can be +used to drive LEDs for use as backlights. + +Required properties: +- compatible: "ti,tps65217" +- reg: I2C slave address +- backlight: node for specifying WLED1 and WLED2 lines in TPS65217 +- isel: selection bit, valid values: 1 for ISEL1 (low-level) and 2 for ISEL2 (high-level) +- fdim: PWM dimming frequency, valid values: 100, 200, 500, 1000 +- default-brightness: valid values: 0-100 + +Each regulator is defined using the standard binding for regulators. + +Example: + + tps: tps@24 { + reg = <0x24>; + compatible = "ti,tps65217"; + backlight { + isel = <1>; /* 1 - ISET1, 2 ISET2 */ + fdim = <100>; /* TPS65217_BL_FDIM_100HZ */ + default-brightness = <50>; + }; + }; + |