1 files changed, 0 insertions, 86 deletions
diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
deleted file mode 100644
index 3e2a2652eb19..000000000000
--- a/Documentation/devicetree/bindings/media/renesas,ceu.txt
+++ /dev/null
@@ -1,86 +0,0 @@
-Renesas Capture Engine Unit (CEU)
-----------------------------------------------
-
-The Capture Engine Unit is the image capture interface found in the Renesas
-SH Mobile, R-Mobile and RZ SoCs.
-
-The interface supports a single parallel input with data bus width of 8 or 16
-bits.
-
-Required properties:
-- compatible: Shall be one of the following values:
-	"renesas,r7s72100-ceu" for CEU units found in RZ/A1H and RZ/A1M SoCs
-	"renesas,r8a7740-ceu" for CEU units found in R-Mobile A1 R8A7740 SoCs
-- reg: Registers address base and size.
-- interrupts: The interrupt specifier.
-
-The CEU supports a single parallel input and should contain a single 'port'
-subnode with a single 'endpoint'. Connection to input devices are modeled
-according to the video interfaces OF bindings specified in:
-[1] Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Optional endpoint properties applicable to parallel input bus described in
-the above mentioned "video-interfaces.txt" file are supported.
-
-- hsync-active: See [1] for description. If property is not present,
-  default is active high.
-- vsync-active: See [1] for description. If property is not present,
-  default is active high.
-- bus-width: See [1] for description. Accepted values are '8' and '16'.
-  If property is not present, default is '8'.
-- field-even-active: See [1] for description. If property is not present,
-  an even field is identified by a logic 0 (active-low signal).
-
-Example:
-
-The example describes the connection between the Capture Engine Unit and an
-OV7670 image sensor connected to i2c1 interface.
-
-ceu: ceu@e8210000 {
-	reg = <0xe8210000 0x209c>;
-	compatible = "renesas,r7s72100-ceu";
-	interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&vio_pins>;
-
-	status = "okay";
-
-	port {
-		ceu_in: endpoint {
-			remote-endpoint = <&ov7670_out>;
-
-			hsync-active = <1>;
-			vsync-active = <0>;
-		};
-	};
-};
-
-i2c1: i2c@fcfee400 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ov7670: camera@21 {
-		compatible = "ovti,ov7670";
-		reg = <0x21>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&vio_pins>;
-
-		reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
-		powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
-
-		port {
-			ov7670_out: endpoint {
-				remote-endpoint = <&ceu_in>;
-
-				hsync-active = <1>;
-				vsync-active = <0>;
-			};
-		};
-	};
-};