diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/s2mps11.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/s2mps11.txt | 28 |
1 files changed, 21 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/mfd/s2mps11.txt b/Documentation/devicetree/bindings/mfd/s2mps11.txt index 57a045016fca..09b94c97faac 100644 --- a/Documentation/devicetree/bindings/mfd/s2mps11.txt +++ b/Documentation/devicetree/bindings/mfd/s2mps11.txt @@ -1,5 +1,5 @@ -* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator +* Samsung S2MPS11/13/14/15 and S2MPU02 Voltage and Current Regulator The Samsung S2MPS11 is a multi-function device which includes voltage and current regulators, RTC, charger controller and other sub-blocks. It is @@ -7,17 +7,28 @@ interfaced to the host controller using an I2C interface. Each sub-block is addressed by the host system using different I2C slave addresses. Required properties: -- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic" - or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic". +- compatible: Should be one of the following + - "samsung,s2mps11-pmic" + - "samsung,s2mps13-pmic" + - "samsung,s2mps14-pmic" + - "samsung,s2mps15-pmic" + - "samsung,s2mpu02-pmic". - reg: Specifies the I2C slave address of the pmic block. It should be 0x66. Optional properties: - interrupt-parent: Specifies the phandle of the interrupt controller to which the interrupts from s2mps11 are delivered to. - interrupts: Interrupt specifiers for interrupt sources. +- samsung,s2mps11-wrstbi-ground: Indicates that WRSTBI pin of PMIC is pulled + down. When the system is suspended it will always go down thus triggerring + unwanted buck warm reset (setting buck voltages to default values). +- samsung,s2mps11-acokb-ground: Indicates that ACOKB pin of S2MPS11 PMIC is + connected to the ground so the PMIC must manually set PWRHOLD bit in CTRL1 + register to turn off the power. Usually the ACOKB is pulled up to VBATT so + when PWRHOLD pin goes low, the rising ACOKB will trigger power off. Optional nodes: -- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768 +- clocks: s2mps11, s2mps13, s2mps15 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz outputs, so to register these as clocks with common clock framework instantiate a sub-node named "clocks". It uses the common clock binding documented in : @@ -30,12 +41,13 @@ Optional nodes: the clock which they consume. Clock ID Devices ---------------------------------------------------------- - 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767 - 32KhzCP 1 S2MPS11, S2MPS13, S5M8767 - 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767 + 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 + 32KhzCP 1 S2MPS11, S2MPS13, S2MPS15, S5M8767 + 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S2MPS15, S5M8767 - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", "samsung,s2mps14-clk", "samsung,s5m8767-clk" + The s2msp15 uses the same compatible as s2mps13, as both provides similar clocks. - regulators: The regulators of s2mps11 that have to be instantiated should be included in a sub-node named 'regulators'. Regulator nodes included in this @@ -83,6 +95,7 @@ as per the datasheet of s2mps11. - S2MPS11: 1 to 38 - S2MPS13: 1 to 40 - S2MPS14: 1 to 25 + - S2MPS15: 1 to 27 - S2MPU02: 1 to 28 - Example: LDO1, LDO2, LDO28 - BUCKn @@ -90,6 +103,7 @@ as per the datasheet of s2mps11. - S2MPS11: 1 to 10 - S2MPS13: 1 to 10 - S2MPS14: 1 to 5 + - S2MPS15: 1 to 10 - S2MPU02: 1 to 7 - Example: BUCK1, BUCK2, BUCK9 |