diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl')
5 files changed, 25 insertions, 43 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt index 08a4a32c8eb0..0326154c7925 100644 --- a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt @@ -134,12 +134,12 @@ mfio80 ddr_debug, mips_trace_data, mips_debug mfio81 dreq0, mips_trace_data, eth_debug mfio82 dreq1, mips_trace_data, eth_debug mfio83 mips_pll_lock, mips_trace_data, usb_debug -mfio84 sys_pll_lock, mips_trace_data, usb_debug -mfio85 wifi_pll_lock, mips_trace_data, sdhost_debug -mfio86 bt_pll_lock, mips_trace_data, sdhost_debug -mfio87 rpu_v_pll_lock, dreq2, socif_debug -mfio88 rpu_l_pll_lock, dreq3, socif_debug -mfio89 audio_pll_lock, dreq4, dreq5 +mfio84 audio_pll_lock, mips_trace_data, usb_debug +mfio85 rpu_v_pll_lock, mips_trace_data, sdhost_debug +mfio86 rpu_l_pll_lock, mips_trace_data, sdhost_debug +mfio87 sys_pll_lock, dreq2, socif_debug +mfio88 wifi_pll_lock, dreq3, socif_debug +mfio89 bt_pll_lock, dreq4, dreq5 tck trstn tdi diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 3f6a524cc5ff..32f4a2d6d0b3 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -1,13 +1,16 @@ == Amlogic Meson pinmux controller == Required properties for the root node: - - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl" + - compatible: one of "amlogic,meson8-cbus-pinctrl" + "amlogic,meson8b-cbus-pinctrl" + "amlogic,meson8-aobus-pinctrl" + "amlogic,meson8b-aobus-pinctrl" - reg: address and size of registers controlling irq functionality === GPIO sub-nodes === -The 2 power domains of the controller (regular and always-on) are -represented as sub-nodes and each of them acts as a GPIO controller. +The GPIO bank for the controller is represented as a sub-node and it acts as a +GPIO controller. Required properties for sub-nodes are: - reg: should contain address and size for mux, pull-enable, pull and @@ -18,10 +21,6 @@ Required properties for sub-nodes are: - gpio-controller: identifies the node as a gpio controller - #gpio-cells: must be 2 -Valid sub-node names are: - - "banks" for the regular domain - - "ao-bank" for the always-on domain - === Other sub-nodes === Child nodes without the "gpio-controller" represent some desired @@ -45,7 +44,7 @@ pinctrl-bindings.txt === Example === pinctrl: pinctrl@c1109880 { - compatible = "amlogic,meson8-pinctrl"; + compatible = "amlogic,meson8-cbus-pinctrl"; reg = <0xc1109880 0x10>; #address-cells = <1>; #size-cells = <1>; @@ -61,15 +60,6 @@ pinctrl-bindings.txt #gpio-cells = <2>; }; - gpio_ao: ao-bank@c1108030 { - reg = <0xc8100014 0x4>, - <0xc810002c 0x4>, - <0xc8100024 0x8>; - reg-names = "mux", "pull", "gpio"; - gpio-controller; - #gpio-cells = <2>; - }; - nand { mux { groups = "nand_io", "nand_io_ce0", "nand_io_ce1", @@ -79,18 +69,4 @@ pinctrl-bindings.txt function = "nand"; }; }; - - uart_ao_a { - mux { - groups = "uart_tx_ao_a", "uart_rx_ao_a", - "uart_cts_ao_a", "uart_rts_ao_a"; - function = "uart_ao"; - }; - - conf { - pins = "GPIOAO_0", "GPIOAO_1", - "GPIOAO_2", "GPIOAO_3"; - bias-disable; - }; - }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt index 30676ded85bb..4048f43a9d29 100644 --- a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt @@ -1,6 +1,12 @@ Device tree binding for NVIDIA Tegra XUSB pad controller ======================================================== +NOTE: It turns out that this binding isn't an accurate description of the XUSB +pad controller. While the description is good enough for the functional subset +required for PCIe and SATA, it lacks the flexibility to represent the features +needed for USB. For the new binding, see ../phy/nvidia,tegra-xusb-padctl.txt. +The binding described in this file is deprecated and should not be used. + The Tegra XUSB pad controller manages a set of lanes, each of which can be assigned to one out of a set of different pads. Some of these pads have an associated PHY that must be powered up before the pad can be used. @@ -79,7 +85,7 @@ Example: SoC file extract: ----------------- - padctl@0,7009f000 { + padctl@7009f000 { compatible = "nvidia,tegra124-xusb-padctl"; reg = <0x0 0x7009f000 0x0 0x1000>; resets = <&tegra_car 142>; @@ -91,7 +97,7 @@ SoC file extract: Board file extract: ------------------- - pcie-controller@0,01003000 { + pcie-controller@01003000 { ... phys = <&padctl 0>; @@ -102,7 +108,7 @@ Board file extract: ... - padctl: padctl@0,7009f000 { + padctl: padctl@7009f000 { pinctrl-0 = <&padctl_default>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index a90c812ad642..a54c39ebbf8b 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -122,7 +122,7 @@ to specify in a pin configuration subnode: 2: 1.5uA (PMIC_GPIO_PULL_UP_1P5) 3: 31.5uA (PMIC_GPIO_PULL_UP_31P5) 4: 1.5uA + 30uA boost (PMIC_GPIO_PULL_UP_1P5_30) - If this property is ommited 30uA strength will be used if + If this property is omitted 30uA strength will be used if pull up is selected - bias-high-impedance: diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index ffadb7a371f6..74e6ec0339d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -72,8 +72,8 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that -have a configurable I/O voltage, the power-source value should be the +bias-disable, bias-pull-up, bias-pull-down, drive strength and power-source. For +pins that have a configurable I/O voltage, the power-source value should be the nominal I/O voltage in millivolts. |