diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
5 files changed, 164 insertions, 26 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 9462ab7ddd1f..3c821cda1ad0 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -48,7 +48,7 @@ Optional subnode-properties: Examples: -pinctrl@01c20800 { +pio: pinctrl@01c20800 { compatible = "allwinner,sun5i-a13-pinctrl"; reg = <0x01c20800 0x400>; #address-cells = <1>; @@ -68,3 +68,38 @@ pinctrl@01c20800 { allwinner,pull = <0>; }; }; + + +GPIO and interrupt controller +----------------------------- + +This hardware also acts as a GPIO controller and an interrupt +controller. + +Consumers that would want to refer to one or the other (or both) +should provide through the usual *-gpios and interrupts properties a +cell with 3 arguments, first the number of the bank, then the pin +inside that bank, and finally the flags for the GPIO/interrupts. + +Example: + +xio: gpio@38 { + compatible = "nxp,pcf8574a"; + reg = <0x38>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-parent = <&pio>; + interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/cnxt,cx92755-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cnxt,cx92755-pinctrl.txt new file mode 100644 index 000000000000..23ce8dc26990 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/cnxt,cx92755-pinctrl.txt @@ -0,0 +1,86 @@ +Conexant Digicolor CX92755 General Purpose Pin Mapping + +This document describes the device tree binding of the pin mapping hardware +modules in the Conexant Digicolor CX92755 SoCs. The CX92755 in one of the +Digicolor series of SoCs. + +=== Pin Controller Node === + +Required Properties: + +- compatible: Must be "cnxt,cx92755-pinctrl" +- reg: Base address of the General Purpose Pin Mapping register block and the + size of the block. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Must be <2>. The first cell is the pin number and the + second cell is used to specify flags. See include/dt-bindings/gpio/gpio.h + for possible values. + +For example, the following is the bare minimum node: + + pinctrl: pinctrl@f0000e20 { + compatible = "cnxt,cx92755-pinctrl"; + reg = <0xf0000e20 0x100>; + gpio-controller; + #gpio-cells = <2>; + }; + +As a pin controller device, in addition to the required properties, this node +should also contain the pin configuration nodes that client devices reference, +if any. + +For a general description of GPIO bindings, please refer to ../gpio/gpio.txt. + +=== Pin Configuration Node === + +Each pin configuration node is a sub-node of the pin controller node and is a +container of an arbitrary number of subnodes, called pin group nodes in this +document. + +Please refer to the pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the definition of a +"pin configuration node". + +=== Pin Group Node === + +A pin group node specifies the desired pin mux for an arbitrary number of +pins. The name of the pin group node is optional and not used. + +A pin group node only affects the properties specified in the node, and has no +effect on any properties that are omitted. + +The pin group node accepts a subset of the generic pin config properties. For +details generic pin config properties, please refer to pinctrl-bindings.txt +and <include/linux/pinctrl/pinconfig-generic.h>. + +Required Pin Group Node Properties: + +- pins: Multiple strings. Specifies the name(s) of one or more pins to be + configured by this node. The format of a pin name string is "GP_xy", where x + is an uppercase character from 'A' to 'R', and y is a digit from 0 to 7. +- function: String. Specifies the pin mux selection. Values must be one of: + "gpio", "client_a", "client_b", "client_c" + +Example: + pinctrl: pinctrl@f0000e20 { + compatible = "cnxt,cx92755-pinctrl"; + reg = <0xf0000e20 0x100>; + + uart0_default: uart0_active { + data_signals { + pins = "GP_O0", "GP_O1"; + function = "client_b"; + }; + }; + }; + + uart0: uart@f0000740 { + compatible = "cnxt,cx92755-usart"; + ... + pinctrl-0 = <&uart0_default>; + pinctrl-names = "default"; + }; + +In the example above, a single pin group configuration node defines the +"client select" for the Rx and Tx signals of uart0. The uart0 node references +that pin configuration node using the &uart0_default phandle. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt index ed19991aad35..d7803a2a94e9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -7,8 +7,13 @@ of PMIC's from Qualcomm. Usage: required Value type: <string> Definition: Should contain one of: + "qcom,pm8018-mpp", + "qcom,pm8038-mpp", + "qcom,pm8821-mpp", "qcom,pm8841-mpp", "qcom,pm8916-mpp", + "qcom,pm8917-mpp", + "qcom,pm8921-mpp", "qcom,pm8941-mpp", "qcom,pma8084-mpp", @@ -77,12 +82,9 @@ to specify in a pin configuration subnode: Value type: <string> Definition: Specify the alternative function to be configured for the specified pins. Valid values are: - "normal", - "paired", - "dtest1", - "dtest2", - "dtest3", - "dtest4" + "digital", + "analog", + "sink" - bias-disable: Usage: optional @@ -127,12 +129,18 @@ to specify in a pin configuration subnode: Definition: Selects the power source for the specified pins. Valid power sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> -- qcom,analog-mode: +- qcom,analog-level: Usage: optional - Value type: <none> - Definition: Selects Analog mode of operation: combined with input-enable - and/or output-high, output-low MPP could operate as - Bidirectional Logic, Analog Input, Analog Output. + Value type: <u32> + Definition: Selects the source for analog output. Valued values are + defined in <dt-binding/pinctrl/qcom,pmic-mpp.h> + PMIC_MPP_AOUT_LVL_* + +- qcom,dtest: + Usage: optional + Value type: <u32> + Definition: Selects which dtest rail to be routed in the various functions. + Valid values are 1-4 - qcom,amux-route: Usage: optional @@ -140,6 +148,10 @@ to specify in a pin configuration subnode: Definition: Selects the source for analog input. Valid values are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6... +- qcom,paired: + Usage: optional + Value type: <none> + Definition: Indicates that the pin should be operating in paired mode. Example: @@ -156,7 +168,7 @@ Example: pm8841_default: default { gpio { pins = "mpp1", "mpp2", "mpp3", "mpp4"; - function = "normal"; + function = "digital"; input-enable; power-source = <PM8841_MPP_S3>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 51cee44fc140..9496934528bd 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -58,12 +58,12 @@ are parsed through phandles and processed purely based on their content. Pin Configuration Node Properties: -- renesas,pins : An array of strings, each string containing the name of a pin. -- renesas,groups : An array of strings, each string containing the name of a pin +- pins : An array of strings, each string containing the name of a pin. +- groups : An array of strings, each string containing the name of a pin group. -- renesas,function: A string containing the name of the function to mux to the - pin group(s) specified by the renesas,groups property +- function: A string containing the name of the function to mux to the pin + group(s) specified by the groups property. Valid values for pin, group and function names can be found in the group and function arrays of the PFC data file corresponding to the SoC @@ -71,7 +71,9 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up and bias-pull-down. +bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that +have a configurable I/O voltage, the power-source value should be the +nominal I/O voltage in millivolts. GPIO @@ -141,19 +143,19 @@ Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps mmcif_pins: mmcif { mux { - renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; - renesas,function = "mmc0"; + groups = "mmc0_data8_0", "mmc0_ctrl_0"; + function = "mmc0"; }; cfg { - renesas,groups = "mmc0_data8_0"; - renesas,pins = "PORT279"; + groups = "mmc0_data8_0"; + pins = "PORT279"; bias-pull-up; }; }; scifa4_pins: scifa4 { - renesas,groups = "scifa4_data", "scifa4_ctrl"; - renesas,function = "scifa4"; + groups = "scifa4_data", "scifa4_ctrl"; + function = "scifa4"; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt index f63fcb3ed352..2213802435e0 100644 --- a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt +++ b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt @@ -3,7 +3,9 @@ ST Ericsson Nomadik pinmux controller Required properties: - compatible: "stericsson,db8500-pinctrl", "stericsson,db8540-pinctrl", "stericsson,stn8815-pinctrl" -- reg: Should contain the register physical address and length of the PRCMU. +- nomadik-gpio-chips: array of phandles to the corresponding GPIO chips + (these have the register ranges used by the pin controller). +- prcm: phandle to the PRCMU managing the back end of this pin controller Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the @@ -74,7 +76,8 @@ Example board file extract: pinctrl@80157000 { compatible = "stericsson,db8500-pinctrl"; - reg = <0x80157000 0x2000>; + nomadik-gpio-chips = <&gpio0>, <&gpio1>, <&gpio2>, <&gpio3>; + prcm = <&prcmu>; pinctrl-names = "default"; |