diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
99 files changed, 4169 insertions, 198 deletions
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index cbef09b5c8a7..69ddf9fad2dc 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -16,6 +16,9 @@ Required properties: performs the same operation). "marvell,"aurora-outer-cache: Marvell Controller designed to be compatible with the ARM one with outer cache mode. + "bcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an + offset needs to be added to the address before passing down to the L2 + cache controller - cache-unified : Specifies the cache is a unified cache. - cache-level : Should be set to 2 for a level 2 cache. - reg : Physical base address and size of cache controller's memory mapped diff --git a/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt b/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt index f2f2171e530e..9e5f73412cd7 100644 --- a/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt +++ b/Documentation/devicetree/bindings/arm/samsung/interrupt-combiner.txt @@ -5,7 +5,7 @@ can combine interrupt sources as a group and provide a single interrupt request for the group. The interrupt request from each group are connected to a parent interrupt controller, such as GIC in case of Exynos4210. -The interrupt combiner controller consists of multiple combiners. Upto eight +The interrupt combiner controller consists of multiple combiners. Up to eight interrupt sources can be connected to a combiner. The combiner outputs one combined interrupt for its eight interrupt sources. The combined interrupt is usually connected to a parent interrupt controller. @@ -14,8 +14,8 @@ A single node in the device tree is used to describe the interrupt combiner controller module (which includes multiple combiners). A combiner in the interrupt controller module shares config/control registers with other combiners. For example, a 32-bit interrupt enable/disable config register -can accommodate upto 4 interrupt combiners (with each combiner supporting -upto 8 interrupt sources). +can accommodate up to 4 interrupt combiners (with each combiner supporting +up to 8 interrupt sources). Required properties: - compatible: should be "samsung,exynos4210-combiner". diff --git a/Documentation/devicetree/bindings/arm/spear/shirq.txt b/Documentation/devicetree/bindings/arm/spear/shirq.txt index 13fbb8866bd6..715a013ed4bd 100644 --- a/Documentation/devicetree/bindings/arm/spear/shirq.txt +++ b/Documentation/devicetree/bindings/arm/spear/shirq.txt @@ -14,7 +14,7 @@ A single node in the device tree is used to describe the shared interrupt multiplexor (one node for all groups). A group in the interrupt controller shares config/control registers with other groups. For example, a 32-bit interrupt enable/disable config register can -accommodate upto 4 interrupt groups. +accommodate up to 4 interrupt groups. Required properties: - compatible: should be, either of diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index b519f9b699c3..3ec0c5c4f0e9 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -12,6 +12,11 @@ Optional properties: - calxeda,port-phys: phandle-combophy and lane assignment, which maps each SATA port to a combophy and a lane within that combophy +- calxeda,sgpio-gpio: phandle-gpio bank, bit offset, and default on or off, + which indicates that the driver supports SGPIO + indicator lights using the indicated GPIOs +- calxeda,led-order : a u32 array that map port numbers to offsets within the + SGPIO bitstream. - dma-coherent : Present if dma operations are coherent Example: diff --git a/Documentation/devicetree/bindings/clock/nspire-clock.txt b/Documentation/devicetree/bindings/clock/nspire-clock.txt new file mode 100644 index 000000000000..7c3bc8bb5b9f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nspire-clock.txt @@ -0,0 +1,24 @@ +TI-NSPIRE Clocks + +Required properties: +- compatible: Valid compatible properties include: + "lsi,nspire-cx-ahb-divider" for the AHB divider in the CX model + "lsi,nspire-classic-ahb-divider" for the AHB divider in the older model + "lsi,nspire-cx-clock" for the base clock in the CX model + "lsi,nspire-classic-clock" for the base clock in the older model + +- reg: Physical base address of the controller and length of memory mapped + region. + +Optional: +- clocks: For the "nspire-*-ahb-divider" compatible clocks, this is the parent + clock where it divides the rate from. + +Example: + +ahb_clk { + #clock-cells = <0>; + compatible = "lsi,nspire-cx-clock"; + reg = <0x900B0000 0x4>; + clocks = <&base_clk>; +}; diff --git a/Documentation/devicetree/bindings/clock/rockchip.txt b/Documentation/devicetree/bindings/clock/rockchip.txt new file mode 100644 index 000000000000..a891c823ed44 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip.txt @@ -0,0 +1,74 @@ +Device Tree Clock bindings for arch-rockchip + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +== Gate clocks == + +The gate registers form a continuos block which makes the dt node +structure a matter of taste, as either all gates can be put into +one gate clock spanning all registers or they can be divided into +the 10 individual gates containing 16 clocks each. +The code supports both approaches. + +Required properties: +- compatible : "rockchip,rk2928-gate-clk" +- reg : shall be the control register address(es) for the clock. +- #clock-cells : from common clock binding; shall be set to 1 +- clock-output-names : the corresponding gate names that the clock controls +- clocks : should contain the parent clock for each individual gate, + therefore the number of clocks elements should match the number of + clock-output-names + +Example using multiple gate clocks: + + clk_gates0: gate-clk@200000d0 { + compatible = "rockchip,rk2928-gate-clk"; + reg = <0x200000d0 0x4>; + clocks = <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>, + <&dummy>, <&dummy>; + + clock-output-names = + "gate_core_periph", "gate_cpu_gpll", + "gate_ddrphy", "gate_aclk_cpu", + "gate_hclk_cpu", "gate_pclk_cpu", + "gate_atclk_cpu", "gate_i2s0", + "gate_i2s0_frac", "gate_i2s1", + "gate_i2s1_frac", "gate_i2s2", + "gate_i2s2_frac", "gate_spdif", + "gate_spdif_frac", "gate_testclk"; + + #clock-cells = <1>; + }; + + clk_gates1: gate-clk@200000d4 { + compatible = "rockchip,rk2928-gate-clk"; + reg = <0x200000d4 0x4>; + clocks = <&xin24m>, <&xin24m>, + <&xin24m>, <&dummy>, + <&dummy>, <&xin24m>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>, + <&xin24m>, <&dummy>; + + clock-output-names = + "gate_timer0", "gate_timer1", + "gate_timer2", "gate_jtag", + "gate_aclk_lcdc1_src", "gate_otgphy0", + "gate_otgphy1", "gate_ddr_gpll", + "gate_uart0", "gate_frac_uart0", + "gate_uart1", "gate_frac_uart1", + "gate_uart2", "gate_frac_uart2", + "gate_uart3", "gate_frac_uart3"; + + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt index cc374651662c..c40711e8e8f7 100644 --- a/Documentation/devicetree/bindings/clock/silabs,si5351.txt +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -4,7 +4,7 @@ Reference [1] Si5351A/B/C Data Sheet http://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351.pdf -The Si5351a/b/c are programmable i2c clock generators with upto 8 output +The Si5351a/b/c are programmable i2c clock generators with up to 8 output clocks. Si5351a also has a reduced pin-count package (MSOP10) where only 3 output clocks are accessible. The internal structure of the clock generators can be found in [1]. @@ -44,6 +44,11 @@ Optional child node properties: - silabs,multisynth-source: source pll A(0) or B(1) of corresponding multisynth divider. - silabs,pll-master: boolean, multisynth can change pll frequency. +- silabs,disable-state : clock output disable state, shall be + 0 = clock output is driven LOW when disabled + 1 = clock output is driven HIGH when disabled + 2 = clock output is FLOATING (HIGH-Z) when disabled + 3 = clock output is NEVER disabled ==Example== diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt index 729f52426fe1..d495521a79d2 100644 --- a/Documentation/devicetree/bindings/clock/sunxi.txt +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -12,22 +12,30 @@ Required properties: "allwinner,sun4i-axi-clk" - for the AXI clock "allwinner,sun4i-axi-gates-clk" - for the AXI gates "allwinner,sun4i-ahb-clk" - for the AHB clock - "allwinner,sun4i-ahb-gates-clk" - for the AHB gates + "allwinner,sun4i-ahb-gates-clk" - for the AHB gates on A10 + "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 "allwinner,sun4i-apb0-clk" - for the APB0 clock - "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates + "allwinner,sun4i-apb0-gates-clk" - for the APB0 gates on A10 + "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 "allwinner,sun4i-apb1-clk" - for the APB1 clock "allwinner,sun4i-apb1-mux-clk" - for the APB1 clock muxing - "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates + "allwinner,sun4i-apb1-gates-clk" - for the APB1 gates on A10 + "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13 Required properties for all clocks: - reg : shall be the control register address for the clock. - clocks : shall be the input parent clock(s) phandle for the clock - #clock-cells : from common clock binding; shall be set to 0 except for - "allwinner,sun4i-*-gates-clk" where it shall be set to 1 + "allwinner,*-gates-clk" where it shall be set to 1 -Additionally, "allwinner,sun4i-*-gates-clk" clocks require: +Additionally, "allwinner,*-gates-clk" clocks require: - clock-output-names : the corresponding gate names that the clock controls +Clock consumers should specify the desired clocks they use with a +"clocks" phandle cell. Consumers that are using a gated clock should +provide an additional ID in their clock property. The values of this +ID are documented in sunxi/<soc>-gates.txt. + For example: osc24M: osc24M@01c20050 { @@ -50,102 +58,3 @@ cpu: cpu@01c20054 { reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>; }; - - - -Gate clock outputs - -The "allwinner,sun4i-*-gates-clk" clocks provide several gatable outputs; -their corresponding offsets as present on sun4i are listed below. Note that -some of these gates are not present on sun5i. - - * AXI gates ("allwinner,sun4i-axi-gates-clk") - - DRAM 0 - - * AHB gates ("allwinner,sun4i-ahb-gates-clk") - - USB0 0 - EHCI0 1 - OHCI0 2* - EHCI1 3 - OHCI1 4* - SS 5 - DMA 6 - BIST 7 - MMC0 8 - MMC1 9 - MMC2 10 - MMC3 11 - MS 12** - NAND 13 - SDRAM 14 - - ACE 16 - EMAC 17 - TS 18 - - SPI0 20 - SPI1 21 - SPI2 22 - SPI3 23 - PATA 24 - SATA 25** - GPS 26* - - VE 32 - TVD 33 - TVE0 34 - TVE1 35 - LCD0 36 - LCD1 37 - - CSI0 40 - CSI1 41 - - HDMI 43 - DE_BE0 44 - DE_BE1 45 - DE_FE0 46 - DE_FE1 47 - - MP 50 - - MALI400 52 - - * APB0 gates ("allwinner,sun4i-apb0-gates-clk") - - CODEC 0 - SPDIF 1* - AC97 2 - IIS 3 - - PIO 5 - IR0 6 - IR1 7 - - KEYPAD 10 - - * APB1 gates ("allwinner,sun4i-apb1-gates-clk") - - I2C0 0 - I2C1 1 - I2C2 2 - - CAN 4 - SCR 5 - PS20 6 - PS21 7 - - UART0 16 - UART1 17 - UART2 18 - UART3 19 - UART4 20 - UART5 21 - UART6 22 - UART7 23 - -Notation: - [*]: The datasheet didn't mention these, but they are present on AW code - [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt new file mode 100644 index 000000000000..6a03475bbfe2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun4i-a10-gates.txt @@ -0,0 +1,93 @@ +Gate clock outputs +------------------ + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun4i-ahb-gates-clk") + + USB0 0 + EHCI0 1 + OHCI0 2* + EHCI1 3 + OHCI1 4* + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + MMC3 11 + MS 12** + NAND 13 + SDRAM 14 + + ACE 16 + EMAC 17 + TS 18 + + SPI0 20 + SPI1 21 + SPI2 22 + SPI3 23 + PATA 24 + SATA 25** + GPS 26* + + VE 32 + TVD 33 + TVE0 34 + TVE1 35 + LCD0 36 + LCD1 37 + + CSI0 40 + CSI1 41 + + HDMI 43 + DE_BE0 44 + DE_BE1 45 + DE_FE1 46 + DE_FE1 47 + + MP 50 + + MALI400 52 + + * APB0 gates ("allwinner,sun4i-apb0-gates-clk") + + CODEC 0 + SPDIF 1* + AC97 2 + IIS 3 + + PIO 5 + IR0 6 + IR1 7 + + KEYPAD 10 + + * APB1 gates ("allwinner,sun4i-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + + CAN 4 + SCR 5 + PS20 6 + PS21 7 + + UART0 16 + UART1 17 + UART2 18 + UART3 19 + UART4 20 + UART5 21 + UART6 22 + UART7 23 + +Notation: + [*]: The datasheet didn't mention these, but they are present on AW code + [**]: The datasheet had this marked as "NC" but they are used on AW code diff --git a/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt new file mode 100644 index 000000000000..006b6dfc4703 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi/sun5i-a13-gates.txt @@ -0,0 +1,58 @@ +Gate clock outputs +------------------ + + * AXI gates ("allwinner,sun4i-axi-gates-clk") + + DRAM 0 + + * AHB gates ("allwinner,sun5i-a13-ahb-gates-clk") + + USBOTG 0 + EHCI 1 + OHCI 2 + + SS 5 + DMA 6 + BIST 7 + MMC0 8 + MMC1 9 + MMC2 10 + + NAND 13 + SDRAM 14 + + SPI0 20 + SPI1 21 + SPI2 22 + + STIMER 28 + + VE 32 + + LCD 36 + + CSI 40 + + DE_BE 44 + + DE_FE 46 + + IEP 51 + MALI400 52 + + * APB0 gates ("allwinner,sun5i-a13-apb0-gates-clk") + + CODEC 0 + + PIO 5 + IR 6 + + * APB1 gates ("allwinner,sun5i-a13-apb1-gates-clk") + + I2C0 0 + I2C1 1 + I2C2 2 + + UART1 17 + + UART3 19 diff --git a/Documentation/devicetree/bindings/clock/vt8500.txt b/Documentation/devicetree/bindings/clock/vt8500.txt index a880c70d0047..91d71cc0314a 100644 --- a/Documentation/devicetree/bindings/clock/vt8500.txt +++ b/Documentation/devicetree/bindings/clock/vt8500.txt @@ -8,6 +8,8 @@ Required properties: - compatible : shall be one of the following: "via,vt8500-pll-clock" - for a VT8500/WM8505 PLL clock "wm,wm8650-pll-clock" - for a WM8650 PLL clock + "wm,wm8750-pll-clock" - for a WM8750 PLL clock + "wm,wm8850-pll-clock" - for a WM8850 PLL clock "via,vt8500-device-clock" - for a VT/WM device clock Required properties for PLL clocks: diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt index c80e8a3402f0..c280a0e6f42d 100644 --- a/Documentation/devicetree/bindings/dma/atmel-dma.txt +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -24,8 +24,11 @@ The three cells in order are: 1. A phandle pointing to the DMA controller. 2. The memory interface (16 most significant bits), the peripheral interface (16 less significant bits). -3. The peripheral identifier for the hardware handshaking interface. The -identifier can be different for tx and rx. +3. Parameters for the at91 DMA configuration register which are device +dependant: + - bit 7-0: peripheral identifier for the hardware handshaking interface. The + identifier can be different for tx and rx. + - bit 11-8: FIFO configuration. 0 for half FIFO, 1 for ALAP, 1 for ASAP. Example: diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt new file mode 100644 index 000000000000..2717ecb47db9 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-imx-dma.txt @@ -0,0 +1,48 @@ +* Freescale Direct Memory Access (DMA) Controller for i.MX + +This document will only describe differences to the generic DMA Controller and +DMA request bindings as described in dma/dma.txt . + +* DMA controller + +Required properties: +- compatible : Should be "fsl,<chip>-dma". chip can be imx1, imx21 or imx27 +- reg : Should contain DMA registers location and length +- interrupts : First item should be DMA interrupt, second one is optional and + should contain DMA Error interrupt +- #dma-cells : Has to be 1. imx-dma does not support anything else. + +Optional properties: +- #dma-channels : Number of DMA channels supported. Should be 16. +- #dma-requests : Number of DMA requests supported. + +Example: + + dma: dma@10001000 { + compatible = "fsl,imx27-dma"; + reg = <0x10001000 0x1000>; + interrupts = <32 33>; + #dma-cells = <1>; + #dma-channels = <16>; + }; + + +* DMA client + +Clients have to specify the DMA requests with phandles in a list. + +Required properties: +- dmas: List of one or more DMA request specifiers. One DMA request specifier + consists of a phandle to the DMA controller followed by the integer + specifiying the request line. +- dma-names: List of string identifiers for the DMA requests. For the correct + names, have a look at the specific client driver. + +Example: + + sdhci1: sdhci@10013000 { + ... + dmas = <&dma 7>; + dma-names = "rx-tx"; + ... + }; diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt index d1e3f443e205..68cee4f5539f 100644 --- a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.txt @@ -4,14 +4,70 @@ Required properties: - compatible : Should be "fsl,<chip>-sdma" - reg : Should contain SDMA registers location and length - interrupts : Should contain SDMA interrupt +- #dma-cells : Must be <3>. + The first cell specifies the DMA request/event ID. See details below + about the second and third cell. - fsl,sdma-ram-script-name : Should contain the full path of SDMA RAM scripts firmware +The second cell of dma phandle specifies the peripheral type of DMA transfer. +The full ID of peripheral types can be found below. + + ID transfer type + --------------------- + 0 MCU domain SSI + 1 Shared SSI + 2 MMC + 3 SDHC + 4 MCU domain UART + 5 Shared UART + 6 FIRI + 7 MCU domain CSPI + 8 Shared CSPI + 9 SIM + 10 ATA + 11 CCM + 12 External peripheral + 13 Memory Stick Host Controller + 14 Shared Memory Stick Host Controller + 15 DSP + 16 Memory + 17 FIFO type Memory + 18 SPDIF + 19 IPU Memory + 20 ASRC + 21 ESAI + +The third cell specifies the transfer priority as below. + + ID transfer priority + ------------------------- + 0 High + 1 Medium + 2 Low + Examples: sdma@83fb0000 { compatible = "fsl,imx51-sdma", "fsl,imx35-sdma"; reg = <0x83fb0000 0x4000>; interrupts = <6>; + #dma-cells = <3>; fsl,sdma-ram-script-name = "sdma-imx51.bin"; }; + +DMA clients connected to the i.MX SDMA controller must use the format +described in the dma.txt file. + +Examples: + +ssi2: ssi@70014000 { + compatible = "fsl,imx51-ssi", "fsl,imx21-ssi"; + reg = <0x70014000 0x4000>; + interrupts = <30>; + clocks = <&clks 49>; + dmas = <&sdma 24 1 0>, + <&sdma 25 1 0>; + dma-names = "rx", "tx"; + fsl,fifo-depth = <15>; +}; diff --git a/Documentation/devicetree/bindings/dma/shdma.txt b/Documentation/devicetree/bindings/dma/shdma.txt new file mode 100644 index 000000000000..c15994aa1939 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/shdma.txt @@ -0,0 +1,75 @@ +* SHDMA Device Tree bindings + +Sh-/r-mobile and r-car systems often have multiple identical DMA controller +instances, capable of serving any of a common set of DMA slave devices, using +the same configuration. To describe this topology we require all compatible +SHDMA DT nodes to be placed under a DMA multiplexer node. All such compatible +DMAC instances have the same number of channels and use the same DMA +descriptors. Therefore respective DMA DT bindings can also all be placed in the +multiplexer node. Even if there is only one such DMAC instance on a system, it +still has to be placed under such a multiplexer node. + +* DMA multiplexer + +Required properties: +- compatible: should be "renesas,shdma-mux" +- #dma-cells: should be <1>, see "dmas" property below + +Optional properties (currently unused): +- dma-channels: number of DMA channels +- dma-requests: number of DMA request signals + +* DMA controller + +Required properties: +- compatible: should be "renesas,shdma" + +Example: + dmac: dma-mux0 { + compatible = "renesas,shdma-mux"; + #dma-cells = <1>; + dma-channels = <6>; + dma-requests = <256>; + reg = <0 0>; /* Needed for AUXDATA */ + #address-cells = <1>; + #size-cells = <1>; + ranges; + + dma0: shdma@fe008020 { + compatible = "renesas,shdma"; + reg = <0xfe008020 0x270>, + <0xfe009000 0xc>; + interrupt-parent = <&gic>; + interrupts = <0 34 4 + 0 28 4 + 0 29 4 + 0 30 4 + 0 31 4 + 0 32 4 + 0 33 4>; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5"; + }; + + dma1: shdma@fe018020 { + ... + }; + + dma2: shdma@fe028020 { + ... + }; + }; + +* DMA client + +Required properties: +- dmas: a list of <[DMA multiplexer phandle] [MID/RID value]> pairs, + where MID/RID values are fixed handles, specified in the SoC + manual +- dma-names: a list of DMA channel names, one per "dmas" entry + +Example: + dmas = <&dmac 0xd1 + &dmac 0xd2>; + dma-names = "tx", "rx"; diff --git a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt index e5f130159ae1..fff10da5e927 100644 --- a/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt +++ b/Documentation/devicetree/bindings/drm/tilcdc/tilcdc.txt @@ -10,6 +10,14 @@ Recommended properties: services interrupts for this device. - ti,hwmods: Name of the hwmod associated to the LCDC +Optional properties: + - max-bandwidth: The maximum pixels per second that the memory + interface / lcd controller combination can sustain + - max-width: The maximum horizontal pixel width supported by + the lcd controller. + - max-pixelclock: The maximum pixel clock that can be supported + by the lcd controller in KHz. + Example: fb: fb@4830e000 { diff --git a/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt new file mode 100644 index 000000000000..63bf4becd5f0 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-xilinx.txt @@ -0,0 +1,48 @@ +Xilinx plb/axi GPIO controller + +Dual channel GPIO controller with configurable number of pins +(from 1 to 32 per channel). Every pin can be configured as +input/output/tristate. Both channels share the same global IRQ but +local interrupts can be enabled on channel basis. + +Required properties: +- compatible : Should be "xlnx,xps-gpio-1.00.a" +- reg : Address and length of the register set for the device +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). +- gpio-controller : Marks the device node as a GPIO controller. + +Optional properties: +- interrupts : Interrupt mapping for GPIO IRQ. +- interrupt-parent : Phandle for the interrupt controller that + services interrupts for this device. +- xlnx,all-inputs : if n-th bit is setup, GPIO-n is input +- xlnx,dout-default : if n-th bit is 1, GPIO-n default value is 1 +- xlnx,gpio-width : gpio width +- xlnx,tri-default : if n-th bit is 1, GPIO-n is in tristate mode +- xlnx,is-dual : if 1, controller also uses the second channel +- xlnx,all-inputs-2 : as above but for the second channel +- xlnx,dout-default-2 : as above but the second channel +- xlnx,gpio2-width : as above but for the second channel +- xlnx,tri-default-2 : as above but for the second channel + + +Example: +gpio: gpio@40000000 { + #gpio-cells = <2>; + compatible = "xlnx,xps-gpio-1.00.a"; + gpio-controller ; + interrupt-parent = <µblaze_0_intc>; + interrupts = < 6 2 >; + reg = < 0x40000000 0x10000 >; + xlnx,all-inputs = <0x0>; + xlnx,all-inputs-2 = <0x0>; + xlnx,dout-default = <0x0>; + xlnx,dout-default-2 = <0x0>; + xlnx,gpio-width = <0x2>; + xlnx,gpio2-width = <0x2>; + xlnx,interrupt-present = <0x1>; + xlnx,is-dual = <0x1>; + xlnx,tri-default = <0xffffffff>; + xlnx,tri-default-2 = <0xffffffff>; +} ; diff --git a/Documentation/devicetree/bindings/hwmon/g762.txt b/Documentation/devicetree/bindings/hwmon/g762.txt new file mode 100644 index 000000000000..25cc6d8ee575 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/g762.txt @@ -0,0 +1,47 @@ +GMT G762/G763 PWM Fan controller + +Required node properties: + + - "compatible": must be either "gmt,g762" or "gmt,g763" + - "reg": I2C bus address of the device + - "clocks": a fixed clock providing input clock frequency + on CLK pin of the chip. + +Optional properties: + + - "fan_startv": fan startup voltage. Accepted values are 0, 1, 2 and 3. + The higher the more. + + - "pwm_polarity": pwm polarity. Accepted values are 0 (positive duty) + and 1 (negative duty). + + - "fan_gear_mode": fan gear mode. Supported values are 0, 1 and 2. + +If an optional property is not set in .dts file, then current value is kept +unmodified (e.g. u-boot installed value). + +Additional information on operational parameters for the device is available +in Documentation/hwmon/g762. A detailed datasheet for the device is available +at http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf. + +Example g762 node: + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + g762_clk: fixedclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <8192>; + } + } + + g762: g762@3e { + compatible = "gmt,g762"; + reg = <0x3e>; + clocks = <&g762_clk> + fan_gear_mode = <0>; /* chip default */ + fan_startv = <1>; /* chip default */ + pwm_polarity = <0>; /* chip default */ + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt index e42a2ee233e6..7fd7fa25e9b0 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt @@ -10,6 +10,10 @@ Recommended properties : - clock-frequency : desired I2C bus clock frequency in Hz. +Optional properties : + - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds. + This option is only supported in hardware blocks version 1.11a or newer. + Example : i2c@f0000 { @@ -20,3 +24,14 @@ Example : interrupts = <11>; clock-frequency = <400000>; }; + + i2c@1120000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0x1120000 0x1000>; + interrupt-parent = <&ictl>; + interrupts = <12 1>; + clock-frequency = <400000>; + i2c-sda-hold-time-ns = <300>; + }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt index f46d928aa73d..a1ee681942cc 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt @@ -6,7 +6,11 @@ Required properties : - reg : Offset and length of the register set for the device - compatible : Should be "marvell,mv64xxx-i2c" - interrupts : The interrupt number - - clock-frequency : Desired I2C bus clock frequency in Hz. + +Optional properties : + + - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the +default frequency is 100kHz Examples: diff --git a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt b/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt new file mode 100644 index 000000000000..94a425eaa6c7 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt @@ -0,0 +1,24 @@ +* Wondermedia I2C Controller + +Required properties : + + - compatible : should be "wm,wm8505-i2c" + - reg : Offset and length of the register set for the device + - interrupts : <IRQ> where IRQ is the interrupt number + - clocks : phandle to the I2C clock source + +Optional properties : + + - clock-frequency : desired I2C bus clock frequency in Hz. + Valid values are 100000 and 400000. + Default to 100000 if not specified, or invalid value. + +Example : + + i2c_0: i2c@d8280000 { + compatible = "wm,wm8505-i2c"; + reg = <0xd8280000 0x1000>; + interrupts = <19>; + clocks = <&clki2c0>; + clock-frequency = <400000>; + }; diff --git a/Documentation/devicetree/bindings/i2c/ina2xx.txt b/Documentation/devicetree/bindings/i2c/ina2xx.txt new file mode 100644 index 000000000000..a2ad85d7e747 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/ina2xx.txt @@ -0,0 +1,22 @@ +ina2xx properties + +Required properties: +- compatible: Must be one of the following: + - "ti,ina219" for ina219 + - "ti,ina220" for ina220 + - "ti,ina226" for ina226 + - "ti,ina230" for ina230 +- reg: I2C address + +Optional properties: + +- shunt-resistor + Shunt resistor value in micro-Ohm + +Example: + +ina220@44 { + compatible = "ti,ina220"; + reg = <0x44>; + shunt-resistor = <1000>; +}; diff --git a/Documentation/devicetree/bindings/input/pxa27x-keypad.txt b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt new file mode 100644 index 000000000000..f8674f7e5ea5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/pxa27x-keypad.txt @@ -0,0 +1,60 @@ +* Marvell PXA Keypad controller + +Required Properties +- compatible : should be "marvell,pxa27x-keypad" +- reg : Address and length of the register set for the device +- interrupts : The interrupt for the keypad controller +- marvell,debounce-interval : How long time the key will be + recognized when it is pressed. It is a u32 value, and bit[31:16] + is debounce interval for direct key and bit[15:0] is debounce + interval for matrix key. The value is in binary number of 2ms + +Optional Properties For Matrix Keyes +Please refer to matrix-keymap.txt + +Optional Properties for Direct Keyes +- marvell,direct-key-count : How many direct keyes are used. +- marvell,direct-key-mask : The mask indicates which keyes + are used. If bit[X] of the mask is set, the direct key X + is used. +- marvell,direct-key-low-active : Direct key status register + tells the level of pins that connects to the direct keyes. + When this property is set, it means that when the pin level + is low, the key is pressed(active). +- marvell,direct-key-map : It is a u16 array. Each item indicates + the linux key-code for the direct key. + +Optional Properties For Rotary +- marvell,rotary0 : It is a u32 value. Bit[31:16] is the + linux key-code for rotary up. Bit[15:0] is the linux key-code + for rotary down. It is for rotary 0. +- marvell,rotary1 : Same as marvell,rotary0. It is for rotary 1. +- marvell,rotary-rel-key : When rotary is used for relative axes + in the device, the value indicates the key-code for relative + axes measurement in the device. It is a u32 value. Bit[31:16] + is for rotary 1, and Bit[15:0] is for rotary 0. + +Examples: + keypad: keypad@d4012000 { + keypad,num-rows = <3>; + keypad,num-columns = <5>; + linux,keymap = <0x0000000e /* KEY_BACKSPACE */ + 0x0001006b /* KEY_END */ + 0x00020061 /* KEY_RIGHTCTRL */ + 0x0003000b /* KEY_0 */ + 0x00040002 /* KEY_1 */ + 0x0100008b /* KEY_MENU */ + 0x01010066 /* KEY_HOME */ + 0x010200e7 /* KEY_SEND */ + 0x01030009 /* KEY_8 */ + 0x0104000a /* KEY_9 */ + 0x02000160 /* KEY_OK */ + 0x02010003 /* KEY_2 */ + 0x02020004 /* KEY_3 */ + 0x02030005 /* KEY_4 */ + 0x02040006>; /* KEY_5 */ + marvell,rotary0 = <0x006c0067>; /* KEY_UP & KEY_DOWN */ + marvell,direct-key-count = <1>; + marvell,direct-key-map = <0x001c>; + marvell,debounce-interval = <0x001e001e>; + }; diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt index ce3e394c0e64..942d071baaa5 100644 --- a/Documentation/devicetree/bindings/input/samsung-keypad.txt +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -25,14 +25,6 @@ Required Board Specific Properties: - samsung,keypad-num-columns: Number of column lines connected to the keypad controller. -- row-gpios: List of gpios used as row lines. The gpio specifier for - this property depends on the gpio controller to which these row lines - are connected. - -- col-gpios: List of gpios used as column lines. The gpio specifier for - this property depends on the gpio controller to which these column - lines are connected. - - Keys represented as child nodes: Each key connected to the keypad controller is represented as a child node to the keypad controller device node and should include the following properties. @@ -41,6 +33,9 @@ Required Board Specific Properties: - linux,code: the key-code to be reported when the key is pressed and released. +- pinctrl-0: Should specify pin control groups used for this controller. +- pinctrl-names: Should contain only one value - "default". + Optional Properties specific to linux: - linux,keypad-no-autorepeat: do no enable autorepeat feature. - linux,keypad-wakeup: use any event on keypad as wakeup event. @@ -56,17 +51,8 @@ Example: linux,input-no-autorepeat; linux,input-wakeup; - row-gpios = <&gpx2 0 3 3 0 - &gpx2 1 3 3 0>; - - col-gpios = <&gpx1 0 3 0 0 - &gpx1 1 3 0 0 - &gpx1 2 3 0 0 - &gpx1 3 3 0 0 - &gpx1 4 3 0 0 - &gpx1 5 3 0 0 - &gpx1 6 3 0 0 - &gpx1 7 3 0 0>; + pinctrl-names = "default"; + pinctrl-0 = <&keypad_rows &keypad_columns>; key_1 { keypad,row = <0>; diff --git a/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt new file mode 100644 index 000000000000..513d94d6e899 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ti,nspire-keypad.txt @@ -0,0 +1,60 @@ +TI-NSPIRE Keypad + +Required properties: +- compatible: Compatible property value should be "ti,nspire-keypad". + +- reg: Physical base address of the peripheral and length of memory mapped + region. + +- interrupts: The interrupt number for the peripheral. + +- scan-interval: How often to scan in us. Based on a APB speed of 33MHz, the + maximum and minimum delay time is ~2000us and ~500us respectively + +- row-delay: How long to wait before scanning each row. + +- clocks: The clock this peripheral is attached to. + +- linux,keymap: The keymap to use + (see Documentation/devicetree/bindings/input/matrix-keymap.txt) + +Optional properties: +- active-low: Specify that the keypad is active low (i.e. logical low signifies + a key press). + +Example: + +input { + compatible = "ti,nspire-keypad"; + reg = <0x900E0000 0x1000>; + interrupts = <16>; + + scan-interval = <1000>; + row-delay = <200>; + + clocks = <&apb_pclk>; + + linux,keymap = < + 0x0000001c 0x0001001c 0x00040039 + 0x0005002c 0x00060015 0x0007000b + 0x0008000f 0x0100002d 0x01010011 + 0x0102002f 0x01030004 0x01040016 + 0x01050014 0x0106001f 0x01070002 + 0x010a006a 0x02000013 0x02010010 + 0x02020019 0x02030007 0x02040018 + 0x02050031 0x02060032 0x02070005 + 0x02080028 0x0209006c 0x03000026 + 0x03010025 0x03020024 0x0303000a + 0x03040017 0x03050023 0x03060022 + 0x03070008 0x03080035 0x03090069 + 0x04000021 0x04010012 0x04020020 + 0x0404002e 0x04050030 0x0406001e + 0x0407000d 0x04080037 0x04090067 + 0x05010038 0x0502000c 0x0503001b + 0x05040034 0x0505001a 0x05060006 + 0x05080027 0x0509000e 0x050a006f + 0x0600002b 0x0602004e 0x06030068 + 0x06040003 0x0605006d 0x06060009 + 0x06070001 0x0609000f 0x0708002a + 0x0709001d 0x070a0033 >; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt new file mode 100644 index 000000000000..491c97b78384 --- /dev/null +++ b/Documentation/devicetree/bindings/input/touchscreen/ti-tsc-adc.txt @@ -0,0 +1,44 @@ +* TI - TSC ADC (Touschscreen and analog digital converter) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Required properties: +- child "tsc" + ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen + support on the platform. + ti,x-plate-resistance: X plate resistance + ti,coordiante-readouts: The sequencer supports a total of 16 + programmable steps each step is used to + read a single coordinate. A single + readout is enough but multiple reads can + increase the quality. + A value of 5 means, 5 reads for X, 5 for + Y and 2 for Z (always). This utilises 12 + of the 16 software steps available. The + remaining 4 can be used by the ADC. + ti,wire-config: Different boards could have a different order for + connecting wires on touchscreen. We need to provide an + 8 bit number where in the 1st four bits represent the + analog lines and the next 4 bits represent positive/ + negative terminal on that input line. Notations to + represent the input lines and terminals resoectively + is as follows: + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + XP = 0, XN = 1, YP = 2, YN = 3. +- child "adc" + ti,adc-channels: List of analog inputs available for ADC. + AIN0 = 0, AIN1 = 1 and so on till AIN7 = 7. + +Example: + tscadc: tscadc@44e0d000 { + compatible = "ti,am3359-tscadc"; + tsc { + ti,wires = <4>; + ti,x-plate-resistance = <200>; + ti,coordiante-readouts = <5>; + ti,wire-config = <0x00 0x11 0x22 0x33>; + }; + + adc { + ti,adc-channels = <4 5 6 7>; + }; + } diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt new file mode 100644 index 000000000000..e34c6cdd8ba8 --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt @@ -0,0 +1,70 @@ +* ARM System MMU Architecture Implementation + +ARM SoCs may contain an implementation of the ARM System Memory +Management Unit Architecture, which can be used to provide 1 or 2 stages +of address translation to bus masters external to the CPU. + +The SMMU may also raise interrupts in response to various fault +conditions. + +** System MMU required properties: + +- compatible : Should be one of: + + "arm,smmu-v1" + "arm,smmu-v2" + "arm,mmu-400" + "arm,mmu-500" + + depending on the particular implementation and/or the + version of the architecture implemented. + +- reg : Base address and size of the SMMU. + +- #global-interrupts : The number of global interrupts exposed by the + device. + +- interrupts : Interrupt list, with the first #global-irqs entries + corresponding to the global interrupts and any + following entries corresponding to context interrupts, + specified in order of their indexing by the SMMU. + + For SMMUv2 implementations, there must be exactly one + interrupt per context bank. In the case of a single, + combined interrupt, it must be listed multiple times. + +- mmu-masters : A list of phandles to device nodes representing bus + masters for which the SMMU can provide a translation + and their corresponding StreamIDs (see example below). + Each device node linked from this list must have a + "#stream-id-cells" property, indicating the number of + StreamIDs associated with it. + +** System MMU optional properties: + +- smmu-parent : When multiple SMMUs are chained together, this + property can be used to provide a phandle to the + parent SMMU (that is the next SMMU on the path going + from the mmu-masters towards memory) node for this + SMMU. + +Example: + + smmu { + compatible = "arm,smmu-v1"; + reg = <0xba5e0000 0x10000>; + #global-interrupts = <2>; + interrupts = <0 32 4>, + <0 33 4>, + <0 34 4>, /* This is the first context interrupt */ + <0 35 4>, + <0 36 4>, + <0 37 4>; + + /* + * Two DMA controllers, the first with two StreamIDs (0xd01d + * and 0xd01e) and the second with only one (0xd11c). + */ + mmu-masters = <&dma0 0xd01d 0xd01e>, + <&dma1 0xd11c>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-lp55xx.txt b/Documentation/devicetree/bindings/leds/leds-lp55xx.txt new file mode 100644 index 000000000000..d5176882d8b9 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lp55xx.txt @@ -0,0 +1,147 @@ +Binding for TI/National Semiconductor LP55xx Led Drivers + +Required properties: +- compatible: "national,lp5521" or "national,lp5523" or "ti,lp5562" +- reg: I2C slave address +- clock-mode: Input clock mode, (0: automode, 1: internal, 2: external) + +Each child has own specific current settings +- led-cur: Current setting at each led channel (mA x10, 0 if led is not connected) +- max-cur: Maximun current at each led channel. + +Optional properties: +- label: Used for naming LEDs + +Alternatively, each child can have specific channel name +- chan-name: Name of each channel name + +example 1) LP5521 +3 LED channels, external clock used. Channel names are 'lp5521_pri:channel0', +'lp5521_pri:channel1' and 'lp5521_pri:channel2' + +lp5521@32 { + compatible = "national,lp5521"; + reg = <0x32>; + label = "lp5521_pri"; + clock-mode = /bits/ 8 <2>; + + chan0 { + led-cur = /bits/ 8 <0x2f>; + max-cur = /bits/ 8 <0x5f>; + }; + + chan1 { + led-cur = /bits/ 8 <0x2f>; + max-cur = /bits/ 8 <0x5f>; + }; + + chan2 { + led-cur = /bits/ 8 <0x2f>; + max-cur = /bits/ 8 <0x5f>; + }; +}; + +example 2) LP5523 +9 LED channels with specific name. Internal clock used. +The I2C slave address is configurable with ASEL1 and ASEL0 pins. +Available addresses are 32/33/34/35h. + +ASEL1 ASEL0 Address +------------------------- + GND GND 32h + GND VEN 33h + VEN GND 34h + VEN VEN 35h + +lp5523@32 { + compatible = "national,lp5523"; + reg = <0x32>; + clock-mode = /bits/ 8 <1>; + + chan0 { + chan-name = "d1"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan1 { + chan-name = "d2"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan2 { + chan-name = "d3"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan3 { + chan-name = "d4"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan4 { + chan-name = "d5"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan5 { + chan-name = "d6"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan6 { + chan-name = "d7"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan7 { + chan-name = "d8"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; + + chan8 { + chan-name = "d9"; + led-cur = /bits/ 8 <0x14>; + max-cur = /bits/ 8 <0x20>; + }; +}; + +example 3) LP5562 +4 channels are defined. + +lp5562@30 { + compatible = "ti,lp5562"; + reg = <0x30>; + clock-mode = /bits/8 <2>; + + chan0 { + chan-name = "R"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; + + chan1 { + chan-name = "G"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; + + chan2 { + chan-name = "B"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; + + chan3 { + chan-name = "W"; + led-cur = /bits/ 8 <0x20>; + max-cur = /bits/ 8 <0x60>; + }; +}; diff --git a/Documentation/devicetree/bindings/metag/meta.txt b/Documentation/devicetree/bindings/metag/meta.txt new file mode 100644 index 000000000000..f4457f57ab08 --- /dev/null +++ b/Documentation/devicetree/bindings/metag/meta.txt @@ -0,0 +1,30 @@ +* Meta Processor Binding + +This binding specifies what properties must be available in the device tree +representation of a Meta Processor Core, which is the root node in the tree. + +Required properties: + + - compatible: Specifies the compatibility list for the Meta processor. + The type shall be <string> and the value shall include "img,meta". + +Optional properties: + + - clocks: Clock consumer specifiers as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + + - clock-names: Clock consumer names as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt. + +Clocks are identified by name. Valid clocks are: + + - "core": The Meta core clock from which the Meta timers are derived. + +* Examples + +/ { + compatible = "toumaz,tz1090", "img,meta"; + + clocks = <&meta_core_clk>; + clock-names = "core"; +}; diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt new file mode 100644 index 000000000000..0e295c9d8937 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -0,0 +1,62 @@ +Wolfson Arizona class audio SoCs + +These devices are audio SoCs with extensive digital capabilites and a range +of analogue I/O. + +Required properties: + + - compatible : one of the following chip-specific strings: + "wlf,wm5102" + "wlf,wm5110" + - reg : I2C slave address when connected using I2C, chip select number when + using SPI. + + - interrupts : The interrupt line the /IRQ signal for the device is + connected to. + - interrupt-controller : Arizona class devices contain interrupt controllers + and may provide interrupt services to other devices. + - interrupt-parent : The parent interrupt controller. + - #interrupt-cells: the number of cells to describe an IRQ, this should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt + + - gpio-controller : Indicates this device is a GPIO controller. + - #gpio-cells : Must be 2. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + + - AVDD1-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, + SPKVDDL-supply, SPKVDDR-supply : power supplies for the device, as covered + in Documentation/devicetree/bindings/regulator/regulator.txt + +Optional properties: + + - wlf,reset : GPIO specifier for the GPIO controlling /RESET + - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA + + - wlf,gpio-defaults : A list of GPIO configuration register values. If + absent, no configuration of these registers is performed. If any + entry has a value that is out of range for a 16 bit register then + the chip default will be used. If present exactly five values must + be specified. + +Example: + +codec: wm5102@1a { + compatible = "wlf,wm5102"; + reg = <0x1a>; + interrupts = <347>; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + + gpio-controller; + #gpio-cells = <2>; + + wlf,gpio-defaults = < + 0x00000000, /* AIF1TXLRCLK */ + 0xffffffff, + 0xffffffff, + 0xffffffff, + 0xffffffff, + >; +}; diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt new file mode 100644 index 000000000000..11921cc417bf --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -0,0 +1,55 @@ +Maxim MAX77693 multi-function device + +MAX77693 is a Multifunction device with the following submodules: +- PMIC, +- CHARGER, +- LED, +- MUIC, +- HAPTIC + +It is interfaced to host controller using i2c. +This document describes the bindings for the mfd device. + +Required properties: +- compatible : Must be "maxim,max77693". +- reg : Specifies the i2c slave address of PMIC block. +- interrupts : This i2c device has an IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Optional properties: +- regulators : The regulators of max77693 have to be instantiated under subnod + named "regulators" using the following format. + + regulators { + regualtor-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER + standard regulator constratints[*]. + }; + + [*] refer Documentation/devicetree/bindings/regulator/regulator.txt + +Example: + max77693@66 { + compatible = "maxim,max77693"; + reg = <0x66>; + interrupt-parent = <&gpx1>; + interrupts = <5 2>; + + regulators { + esafeout@1 { + regulator-compatible = "ESAFEOUT1"; + regulator-name = "ESAFEOUT1"; + regulator-boot-on; + }; + esafeout@2 { + regulator-compatible = "ESAFEOUT2"; + regulator-name = "ESAFEOUT2"; + }; + charger@0 { + regulator-compatible = "CHARGER"; + regulator-name = "CHARGER"; + regulator-min-microamp = <60000>; + regulator-max-microamp = <2580000>; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/max8998.txt b/Documentation/devicetree/bindings/mfd/max8998.txt new file mode 100644 index 000000000000..23a3650ff2a2 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max8998.txt @@ -0,0 +1,119 @@ +* Maxim MAX8998, National/TI LP3974 multi-function device + +The Maxim MAX8998 is a multi-function device which includes voltage/current +regulators, real time clock, battery charging controller and several +other sub-blocks. It is interfaced using an I2C interface. Each sub-block +is addressed by the host system using different i2c slave address. + +PMIC sub-block +-------------- + +The PMIC sub-block contains a number of voltage and current regulators, +with controllable parameters and dynamic voltage scaling capability. +In addition, it includes a real time clock and battery charging controller +as well. It is accessible at I2C address 0x66. + +Required properties: +- compatible: Should be one of the following: + - "maxim,max8998" for Maxim MAX8998 + - "national,lp3974" or "ti,lp3974" for National/TI LP3974. +- reg: Specifies the i2c slave address of the pmic block. It should be 0x66. + +Optional properties: +- interrupt-parent: Specifies the phandle of the interrupt controller to which + the interrupts from MAX8998 are routed to. +- interrupts: Interrupt specifiers for two interrupt sources. + - First interrupt specifier is for main interrupt. + - Second interrupt specifier is for power-on/-off interrupt. +- max8998,pmic-buck1-dvs-gpios: GPIO specifiers for two host gpios used + for buck 1 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used + for buck 2 dvs. The format of the gpio specifier depends on the gpio + controller. +- max8998,pmic-buck1-default-dvs-idx: Default voltage setting selected from + the possible 4 options selectable by the dvs gpios. The value of this + property should be 0, 1, 2 or 3. If not specified or out of range, + a default value of 0 is taken. +- max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from + the possible 2 options selectable by the dvs gpios. The value of this + property should be 0 or 1. If not specified or out of range, a default + value of 0 is taken. +- max8998,pmic-buck-voltage-lock: If present, disallows changing of + preprogrammed buck dvfs voltages. + +Additional properties required if max8998,pmic-buck1-dvs-gpios is defined: +- max8998,pmic-buck1-dvs-voltage: An array of 4 voltage values in microvolts + for buck1 regulator that can be selected using dvs gpio. + +Additional properties required if max8998,pmic-buck2-dvs-gpio is defined: +- max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts + for buck2 regulator that can be selected using dvs gpio. + +Regulators: All the regulators of MAX8998 to be instantiated shall be +listed in a child node named 'regulators'. Each regulator is represented +by a child node of the 'regulators' node. + + regulator-name { + /* standard regulator bindings here */ + }; + +Following regulators of the MAX8998 PMIC block are supported. Note that +the 'n' in regulator name, as in LDOn or BUCKn, represents the LDO or BUCK +number as described in MAX8998 datasheet. + + - LDOn + - valid values for n are 2 to 17 + - Example: LDO2, LDO10, LDO17 + - BUCKn + - valid values for n are 1 to 4. + - Example: BUCK1, BUCK2, BUCK3, BUCK4 + + - ENVICHG: Battery Charging Current Monitor Output. This is a fixed + voltage type regulator + + - ESAFEOUT1: (ldo19) + - ESAFEOUT2: (ld020) + +Standard regulator bindings are used inside regulator subnodes. Check + Documentation/devicetree/bindings/regulator/regulator.txt +for more details. + +Example: + + pmic@66 { + compatible = "maxim,max8998-pmic"; + reg = <0x66>; + interrupt-parent = <&wakeup_eint>; + interrupts = <4 0>, <3 0>; + + /* Buck 1 DVS settings */ + max8998,pmic-buck1-default-dvs-idx = <0>; + max8998,pmic-buck1-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */ + <&gpx0 1 1 0 0>; /* SET2 */ + max8998,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1000000>, <950000>; + + /* Buck 2 DVS settings */ + max8998,pmic-buck2-default-dvs-idx = <0>; + max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */ + max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>; + + /* Regulators to instantiate */ + regulators { + ldo2_reg: LDO2 { + regulator-name = "VDD_ALIVE_1.1V"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "VDD_ARM_1.2V"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/palmas.txt b/Documentation/devicetree/bindings/mfd/palmas.txt new file mode 100644 index 000000000000..892537d1a48f --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/palmas.txt @@ -0,0 +1,49 @@ +* palmas device tree bindings + +The TI palmas family current members :- +twl6035 (palmas) +twl6037 (palmas) +tps65913 (palmas) +tps65914 (palmas) + +Required properties: +- compatible : Should be from the list + ti,twl6035 + ti,twl6036 + ti,twl6037 + ti,tps65913 + ti,tps65914 + ti,tps80036 +and also the generic series names + ti,palmas +- interrupt-controller : palmas has its own internal IRQs +- #interrupt-cells : should be set to 2 for IRQ number and flags + The first cell is the IRQ number. + The second cell is the flags, encoded as the trigger masks from + Documentation/devicetree/bindings/interrupts.txt +- interrupt-parent : The parent interrupt controller. + +Optional properties: + ti,mux-padX : set the pad register X (1-2) to the correct muxing for the + hardware, if not set will use muxing in OTP. + +Example: + +palmas { + compatible = "ti,twl6035", "ti,palmas"; + reg = <0x48> + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + + ti,mux-pad1 = <0>; + ti,mux-pad2 = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + .... + }; +} diff --git a/Documentation/devicetree/bindings/mfd/twl4030-power.txt b/Documentation/devicetree/bindings/mfd/twl4030-power.txt new file mode 100644 index 000000000000..8e15ec35ac99 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl4030-power.txt @@ -0,0 +1,28 @@ +Texas Instruments TWL family (twl4030) reset and power management module + +The power management module inside the TWL family provides several facilities +to control the power resources, including power scripts. For now, the +binding only supports the complete shutdown of the system after poweroff. + +Required properties: +- compatible : must be "ti,twl4030-power" + +Optional properties: +- ti,use_poweroff: With this flag, the chip will initiates an ACTIVE-to-OFF or + SLEEP-to-OFF transition when the system poweroffs. + +Example: +&i2c1 { + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_power: power { + compatible = "ti,twl4030-power"; + ti,use_poweroff; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 85aada2263d5..458b57f199af 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -28,6 +28,7 @@ Optional properties: - cap-mmc-highspeed: MMC high-speed timing is supported - cap-power-off-card: powering off the card is safe - cap-sdio-irq: enable SDIO IRQ signalling on this interface +- full-pwr-cycle: full power cycle of the card is supported *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt new file mode 100644 index 000000000000..8a3d91d47b6a --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt @@ -0,0 +1,23 @@ +* Rockchip specific extensions to the Synopsis Designware Mobile + Storage Host Controller + +The Synopsis designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsis dw mshc controller properties described +by synopsis-dw-mshc.txt and the properties used by the Rockchip specific +extensions to the Synopsis Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be + - "rockchip,rk2928-dw-mshc": for Rockchip RK2928 and following + +Example: + + rkdwmmc0@12200000 { + compatible = "rockchip,rk2928-dw-mshc"; + reg = <0x12200000 0x1000>; + interrupts = <0 75 0>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt index 726fd2122a13..cdcebea9c6f5 100644 --- a/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/synopsis-dw-mshc.txt @@ -39,6 +39,19 @@ Required Properties: Optional properties: +* clocks: from common clock binding: handle to biu and ciu clocks for the + bus interface unit clock and the card interface unit clock. + +* clock-names: from common clock binding: Shall be "biu" and "ciu". + If the biu clock is missing we'll simply skip enabling it. If the + ciu clock is missing we'll just assume that the clock is running at + clock-frequency. It is an error to omit both the ciu clock and the + clock-frequency. + +* clock-frequency: should be the frequency (in Hz) of the ciu clock. If this + is specified and the ciu clock is specified then we'll try to set the ciu + clock to this at probe time. + * num-slots: specifies the number of slots supported by the controller. The number of physical slots actually used could be equal or less than the value specified by num-slots. If this property is not specified, the value @@ -51,10 +64,13 @@ Optional properties: * card-detect-delay: Delay in milli-seconds before detecting card after card insert event. The default value is 0. -* supports-highspeed: Enables support for high speed cards (upto 50MHz) +* supports-highspeed: Enables support for high speed cards (up to 50MHz) * broken-cd: as documented in mmc core bindings. +* vmmc-supply: The phandle to the regulator to use for vmmc. If this is + specified we'll defer probe until we can find this regulator. + Aliases: - All the MSHC controller nodes should be represented in the aliases node using @@ -67,6 +83,8 @@ board specific portions as listed below. dwmmc0@12200000 { compatible = "snps,dw-mshc"; + clocks = <&clock 351>, <&clock 132>; + clock-names = "biu", "ciu"; reg = <0x12200000 0x1000>; interrupts = <0 75 0>; #address-cells = <1>; @@ -74,11 +92,13 @@ board specific portions as listed below. }; dwmmc0@12200000 { + clock-frequency = <400000000>; num-slots = <1>; supports-highspeed; broken-cd; fifo-depth = <0x80>; card-detect-delay = <200>; + vmmc-supply = <&buck8>; slot@0 { reg = <0>; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt new file mode 100644 index 000000000000..b90bfcd138ff --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -0,0 +1,22 @@ +* Allwinner EMAC ethernet controller + +Required properties: +- compatible: should be "allwinner,sun4i-emac". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: A phandle to a phy node defining the PHY address (as the reg + property, a single integer). +- clocks: A phandle to the reference clock for this device + +Optional properties: +- (local-)mac-address: mac address to be used by this driver + +Example: + +emac: ethernet@01c0b000 { + compatible = "allwinner,sun4i-emac"; + reg = <0x01c0b000 0x1000>; + interrupts = <55>; + clocks = <&ahb_gates 17>; + phy = <&phy0>; +}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt new file mode 100644 index 000000000000..00b9f9a3ec1d --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -0,0 +1,26 @@ +* Allwinner A10 MDIO Ethernet Controller interface + +Required properties: +- compatible: should be "allwinner,sun4i-mdio". +- reg: address and length of the register set for the device. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Example at the SoC level: +mdio@01c0b080 { + compatible = "allwinner,sun4i-mdio"; + reg = <0x01c0b080 0x14>; + #address-cells = <1>; + #size-cells = <0>; +}; + +And at the board level: + +mdio@01c0b080 { + phy-supply = <®_emac_3v3>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt new file mode 100644 index 000000000000..bcbc3f009158 --- /dev/null +++ b/Documentation/devicetree/bindings/net/arc_emac.txt @@ -0,0 +1,38 @@ +* Synopsys ARC EMAC 10/100 Ethernet driver (EMAC) + +Required properties: +- compatible: Should be "snps,arc-emac" +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- clock-frequency: CPU frequency. It is needed to calculate and set polling +period of EMAC. +- max-speed: Maximum supported data-rate in Mbit/s. In some HW configurations +bandwidth of external memory controller might be a limiting factor. That's why +it's required to specify which data-rate is supported on current SoC or FPGA. +For example if only 10 Mbit/s is supported (10BASE-T) set "10". If 100 Mbit/s is +supported (100BASE-TX) set "100". +- phy: PHY device attached to the EMAC via MDIO bus + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Optional properties: +- mac-address: 6 bytes, mac address + +Examples: + + ethernet@c0fc2000 { + compatible = "snps,arc-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + clock-frequency = <80000000>; + max-speed = <100>; + phy = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt index 8ff324eaa889..56d6cc336e1c 100644 --- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -16,6 +16,8 @@ Optional properties: - clock-frequency : The oscillator frequency driving the flexcan device +- xceiver-supply: Regulator that powers the CAN transceiver + Example: can@1c000 { diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 4f2ca6b4a182..05d660e4ac64 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -28,6 +28,8 @@ Optional properties: Slave Properties: Required properties: - phy_id : Specifies slave phy id +- phy-mode : The interface between the SoC and the PHY (a string + that of_get_phy_mode() can understand) - mac-address : Specifies slave MAC address Optional properties: @@ -58,11 +60,13 @@ Examples: cpts_clock_shift = <29>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; @@ -84,11 +88,13 @@ Examples: cpts_clock_shift = <29>; cpsw_emac0: slave@0 { phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; cpsw_emac1: slave@1 { phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; /* Filled in by U-Boot */ mac-address = [ 00 00 00 00 00 00 ]; }; diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt new file mode 100644 index 000000000000..2d39c990e641 --- /dev/null +++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt @@ -0,0 +1,26 @@ +Davicom DM9000 Fast Ethernet controller + +Required properties: +- compatible = "davicom,dm9000"; +- reg : physical addresses and sizes of registers, must contain 2 entries: + first entry : address register, + second entry : data register. +- interrupt-parent : interrupt controller to which the device is connected +- interrupts : interrupt specifier specific to interrupt controller + +Optional properties: +- local-mac-address : A bytestring of 6 bytes specifying Ethernet MAC address + to use (from firmware or bootloader) +- davicom,no-eeprom : Configuration EEPROM is not available +- davicom,ext-phy : Use external PHY + +Example: + + ethernet@18000000 { + compatible = "davicom,dm9000"; + reg = <0x18000000 0x2 0x18000004 0x2>; + interrupt-parent = <&gpn>; + interrupts = <7 4>; + local-mac-address = [00 00 de ad be ef]; + davicom,no-eeprom; + }; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt new file mode 100644 index 000000000000..a73b79f227e1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -0,0 +1,85 @@ +Marvell Orion/Discovery ethernet controller +============================================= + +The Marvell Discovery ethernet controller can be found on Marvell Orion SoCs +(Kirkwood, Dove, Orion5x, and Discovery Innovation) and as part of Marvell +Discovery system controller chips (mv64[345]60). + +The Discovery ethernet controller is described with two levels of nodes. The +first level describes the ethernet controller itself and the second level +describes up to 3 ethernet port nodes within that controller. The reason for +the multiple levels is that the port registers are interleaved within a single +set of controller registers. Each port node describes port-specific properties. + +Note: The above separation is only true for Discovery system controllers. +For Orion SoCs we stick to the separation, although there each controller has +only one port associated. Multiple ports are implemented as multiple single-port +controllers. As Kirkwood has some issues with proper initialization after reset, +an extra compatible string is added for it. + +* Ethernet controller node + +Required controller properties: + - #address-cells: shall be 1. + - #size-cells: shall be 0. + - compatible: shall be one of "marvell,orion-eth", "marvell,kirkwood-eth". + - reg: address and length of the controller registers. + +Optional controller properties: + - clocks: phandle reference to the controller clock. + - marvell,tx-checksum-limit: max tx packet size for hardware checksum. + +* Ethernet port node + +Required port properties: + - device_type: shall be "network". + - compatible: shall be one of "marvell,orion-eth-port", + "marvell,kirkwood-eth-port". + - reg: port number relative to ethernet controller, shall be 0, 1, or 2. + - interrupts: port interrupt. + - local-mac-address: 6 bytes MAC address. + +Optional port properties: + - marvell,tx-queue-size: size of the transmit ring buffer. + - marvell,tx-sram-addr: address of transmit descriptor buffer located in SRAM. + - marvell,tx-sram-size: size of transmit descriptor buffer located in SRAM. + - marvell,rx-queue-size: size of the receive ring buffer. + - marvell,rx-sram-addr: address of receive descriptor buffer located in SRAM. + - marvell,rx-sram-size: size of receive descriptor buffer located in SRAM. + +and + + - phy-handle: phandle reference to ethernet PHY. + +or + + - speed: port speed if no PHY connected. + - duplex: port mode if no PHY connected. + +* Node example: + +mdio-bus { + ... + ethphy: ethernet-phy@8 { + device_type = "ethernet-phy"; + ... + }; +}; + +eth: ethernet-controller@72000 { + compatible = "marvell,orion-eth"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72000 0x2000>; + clocks = <&gate_clk 2>; + marvell,tx-checksum-limit = <1600>; + + ethernet@0 { + device_type = "network"; + compatible = "marvell,orion-eth-port"; + reg = <0>; + interrupts = <29>; + phy-handle = <ðphy>; + local-mac-address = [00 00 00 00 00 00]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt new file mode 100644 index 000000000000..11ace3c3d805 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt @@ -0,0 +1,9 @@ +Micrel KS8851 Ethernet mac + +Required properties: +- compatible = "micrel,ks8851-ml" of parallel interface +- reg : 2 physical address and size of registers for data and command +- interrupts : interrupt connection + +Optional properties: +- local-mac-address : Ethernet mac address to use diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 060bbf098ef3..261c563b5f06 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -12,6 +12,16 @@ Required properties: property - phy-mode: String, operation mode of the PHY interface. Supported values are: "mii", "rmii", "gmii", "rgmii". +- snps,phy-addr phy address to connect to. +- snps,reset-gpio gpio number for phy reset. +- snps,reset-active-low boolean flag to indicate if phy reset is active low. +- snps,reset-delays-us is triplet of delays + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. +- snps,pbl Programmable Burst Length +- snps,fixed-burst Program the DMA to use the fixed burst mode +- snps,mixed-burst Program the DMA to use the mixed burst mode Optional properties: - mac-address: 6 bytes, mac address diff --git a/Documentation/devicetree/bindings/net/via-velocity.txt b/Documentation/devicetree/bindings/net/via-velocity.txt new file mode 100644 index 000000000000..b3db469b1ad7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-velocity.txt @@ -0,0 +1,20 @@ +* VIA Velocity 10/100/1000 Network Controller + +Required properties: +- compatible : Should be "via,velocity-vt6110" +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Optional properties: +- no-eeprom : PCI network cards use an external EEPROM to store data. Embedded + devices quite often set this data in uboot and do not provide an eeprom. + Specify this option if you have no external eeprom. + +Examples: + +eth0@d8004000 { + compatible = "via,velocity-vt6110"; + reg = <0xd8004000 0x400>; + interrupts = <10>; + no-eeprom; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt new file mode 100644 index 000000000000..ddcdeb697c29 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,vf610-pinctrl.txt @@ -0,0 +1,41 @@ +Freescale Vybrid VF610 IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,vf610-iomuxc" +- fsl,pins: two integers array, represents a group of pins mux and config + setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is + a pin working on a specific function, CONFIG is the pad setting value + such as pull-up, speed, ode for this pin. Please refer to Vybrid VF610 + datasheet for the valid pad config settings. + +CONFIG bits definition: +PAD_CTL_SPEED_LOW (1 << 12) +PAD_CTL_SPEED_MED (2 << 12) +PAD_CTL_SPEED_HIGH (3 << 12) +PAD_CTL_SRE_FAST (1 << 11) +PAD_CTL_SRE_SLOW (0 << 11) +PAD_CTL_ODE (1 << 10) +PAD_CTL_HYS (1 << 9) +PAD_CTL_DSE_DISABLE (0 << 6) +PAD_CTL_DSE_150ohm (1 << 6) +PAD_CTL_DSE_75ohm (2 << 6) +PAD_CTL_DSE_50ohm (3 << 6) +PAD_CTL_DSE_37ohm (4 << 6) +PAD_CTL_DSE_30ohm (5 << 6) +PAD_CTL_DSE_25ohm (6 << 6) +PAD_CTL_DSE_20ohm (7 << 6) +PAD_CTL_PUS_100K_DOWN (0 << 4) +PAD_CTL_PUS_47K_UP (1 << 4) +PAD_CTL_PUS_100K_UP (2 << 4) +PAD_CTL_PUS_22K_UP (3 << 4) +PAD_CTL_PKE (1 << 3) +PAD_CTL_PUE (1 << 2) +PAD_CTL_OBE_ENABLE (1 << 1) +PAD_CTL_IBE_ENABLE (1 << 0) +PAD_CTL_OBE_IBE_ENABLE (3 << 0) + +Please refer to vf610-pinfunc.h in device tree source folder +for all available PIN_FUNC_ID for Vybrid VF610. diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt new file mode 100644 index 000000000000..a186181c402b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pdc-pinctrl.txt @@ -0,0 +1,127 @@ +ImgTec TZ1090 PDC pin controller + +Required properties: +- compatible: "img,tz1090-pdc-pinctrl" +- reg: Should contain the register physical address and length of the + SOC_GPIO_CONTROL registers in the PDC register region. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +TZ1090-PDC's pin configuration nodes act as a container for an abitrary number +of subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. For this reason, even seemingly boolean +values are actually tristates in this binding: unspecified, off, or on. +Unspecified is represented as an absent property, and off/on are represented as +integer values 0 and 1. + +Required subnode-properties: +- tz1090,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- tz1090,function: A string containing the name of the function to mux to the + pin or group. Valid values for function names are listed below, including + which pingroups can be muxed to them. +- supported generic pinconfig properties (for further details see + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt): + - bias-disable + - bias-high-impedance + - bias-bus-hold + - bias-pull-up + - bias-pull-down + - input-schmitt-enable + - input-schmitt-disable + - drive-strength: Integer, control drive strength of pins in mA. + 2: 2mA + 4: 4mA + 8: 8mA + 12: 12mA + - low-power-enable: Flag, power-on-start weak pull-down for invalid power. + - low-power-disable: Flag, power-on-start weak pull-down disabled. + +Note that many of these properties are only valid for certain specific pins +or groups. See the TZ1090 TRM for complete details regarding which groups +support which functionality. The Linux pinctrl driver may also be a useful +reference. + +Valid values for pin and group names are: + + pins: + + These all support bias-high-impediance, bias-pull-up, bias-pull-down, and + bias-bus-hold (which can also be provided to any of the groups below to set + it for all gpio pins in that group). + + gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, ext_power. + + mux groups: + + These all support function. + + gpio0 + pins: gpio0. + function: ir_mod_stable_out. + gpio1 + pins: gpio1. + function: ir_mod_power_out. + + drive groups: + + These support input-schmitt-enable, input-schmitt-disable, + drive-strength, low-power-enable, and low-power-disable. + + pdc + pins: gpio0, gpio1, sys_wake0, sys_wake1, sys_wake2, ir_data, + ext_power. + +Example: + + pinctrl_pdc: pinctrl@02006500 { + #gpio-range-cells = <3>; + compatible = "img,tz1090-pdc-pinctrl"; + reg = <0x02006500 0x100>; + }; + +Example board file extracts: + + &pinctrl_pdc { + pinctrl-names = "default"; + pinctrl-0 = <&syswake_default>; + + syswake_default: syswakes { + syswake_cfg { + tz1090,pins = "sys_wake0", + "sys_wake1", + "sys_wake2"; + pull-up; + }; + }; + irmod_default: irmod { + gpio0_cfg { + tz1090,pins = "gpio0"; + tz1090,function = "ir_mod_stable_out"; + }; + gpio1_cfg { + tz1090,pins = "gpio1"; + tz1090,function = "ir_mod_power_out"; + }; + }; + }; + + ir: ir@02006200 { + pinctrl-names = "default"; + pinctrl-0 = <&irmod_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt new file mode 100644 index 000000000000..4b27c99f7f9d --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,tz1090-pinctrl.txt @@ -0,0 +1,227 @@ +ImgTec TZ1090 pin controller + +Required properties: +- compatible: "img,tz1090-pinctrl" +- reg: Should contain the register physical address and length of the pad + configuration registers (CR_PADS_* and CR_IF_CTL0). + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +TZ1090's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. For this reason, even seemingly boolean +values are actually tristates in this binding: unspecified, off, or on. +Unspecified is represented as an absent property, and off/on are represented as +integer values 0 and 1. + +Required subnode-properties: +- tz1090,pins : An array of strings. Each string contains the name of a pin or + group. Valid values for these names are listed below. + +Optional subnode-properties: +- tz1090,function: A string containing the name of the function to mux to the + pin or group. Valid values for function names are listed below, including + which pingroups can be muxed to them. +- supported generic pinconfig properties (for further details see + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt): + - bias-disable + - bias-high-impedance + - bias-bus-hold + - bias-pull-up + - bias-pull-down + - input-schmitt-enable + - input-schmitt-disable + - drive-strength: Integer, control drive strength of pins in mA. + 2: 2mA + 4: 4mA + 8: 8mA + 12: 12mA + + +Note that many of these properties are only valid for certain specific pins +or groups. See the TZ1090 TRM for complete details regarding which groups +support which functionality. The Linux pinctrl driver may also be a useful +reference. + +Valid values for pin and group names are: + + gpio pins: + + These all support bias-high-impediance, bias-pull-up, bias-pull-down, and + bias-bus-hold (which can also be provided to any of the groups below to set + it for all pins in that group). + + They also all support the some form of muxing. Any pins which are contained + in one of the mux groups (see below) can be muxed only to the functions + supported by the mux group. All other pins can be muxed to the "perip" + function which which enables them with their intended peripheral. + + Different pins in the same mux group cannot be muxed to different functions, + however it is possible to mux only a subset of the pins in a mux group to a + particular function and leave the remaining pins unmuxed. This is useful if + the board connects certain pins in a group to other devices to be controlled + by GPIO, and you don't want the usual peripheral to have any control of the + pin. + + ant_sel0, ant_sel1, gain0, gain1, gain2, gain3, gain4, gain5, gain6, gain7, + i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, i2s_lrclk_out, + i2s_mclk, pa_on, pdm_a, pdm_b, pdm_c, pdm_d, pll_on, rx_hp, rx_on, + scb0_sclk, scb0_sdat, scb1_sclk, scb1_sdat, scb2_sclk, scb2_sdat, sdh_cd, + sdh_clk_in, sdh_wp, sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3, + spi0_cs0, spi0_cs1, spi0_cs2, spi0_din, spi0_dout, spi0_mclk, spi1_cs0, + spi1_cs1, spi1_cs2, spi1_din, spi1_dout, spi1_mclk, tft_blank_ls, tft_blue0, + tft_blue1, tft_blue2, tft_blue3, tft_blue4, tft_blue5, tft_blue6, tft_blue7, + tft_green0, tft_green1, tft_green2, tft_green3, tft_green4, tft_green5, + tft_green6, tft_green7, tft_hsync_nr, tft_panelclk, tft_pwrsave, tft_red0, + tft_red1, tft_red2, tft_red3, tft_red4, tft_red5, tft_red6, tft_red7, + tft_vd12acb, tft_vdden_gd, tft_vsync_ns, tx_on, uart0_cts, uart0_rts, + uart0_rxd, uart0_txd, uart1_rxd, uart1_txd. + + bias-high-impediance: supported. + bias-pull-up: supported. + bias-pull-down: supported. + bias-bus-hold: supported. + function: perip or those supported by pin's mux group. + + other pins: + + These other pins are part of various pin groups below, but can't be + controlled as GPIOs. They do however support bias-high-impediance, + bias-pull-up, bias-pull-down, and bias-bus-hold (which can also be provided + to any of the groups below to set it for all pins in that group). + + clk_out0, clk_out1, tck, tdi, tdo, tms, trst. + + bias-high-impediance: supported. + bias-pull-up: supported. + bias-pull-down: supported. + bias-bus-hold: supported. + + mux groups: + + These all support function, and some support drive configs. + + afe + pins: tx_on, rx_on, pll_on, pa_on, rx_hp, ant_sel0, + ant_sel1, gain0, gain1, gain2, gain3, gain4, + gain5, gain6, gain7. + function: afe, ts_out_0. + input-schmitt-enable: supported. + input-schmitt-disable: supported. + drive-strength: supported. + pdm_d + pins: pdm_d. + function: pdm_dac, usb_vbus. + sdh + pins: sdh_cd, sdh_wp, sdh_clk_in. + function: sdh, sdio. + sdio + pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, + sdio_d3. + function: sdio, sdh. + spi1_cs2 + pins: spi1_cs2. + function: spi1_cs2, usb_vbus. + tft + pins: tft_red0, tft_red1, tft_red2, tft_red3, + tft_red4, tft_red5, tft_red6, tft_red7, + tft_green0, tft_green1, tft_green2, tft_green3, + tft_green4, tft_green5, tft_green6, tft_green7, + tft_blue0, tft_blue1, tft_blue2, tft_blue3, + tft_blue4, tft_blue5, tft_blue6, tft_blue7, + tft_vdden_gd, tft_panelclk, tft_blank_ls, + tft_vsync_ns, tft_hsync_nr, tft_vd12acb, + tft_pwrsave. + function: tft, ext_dac, not_iqadc_stb, iqdac_stb, ts_out_1, + lcd_trace, phy_ringosc. + input-schmitt-enable: supported. + input-schmitt-disable: supported. + drive-strength: supported. + + drive groups: + + These all support input-schmitt-enable, input-schmitt-disable, + and drive-strength. + + jtag + pins: tck, trst, tdi, tdo, tms. + scb1 + pins: scb1_sdat, scb1_sclk. + scb2 + pins: scb2_sdat, scb2_sclk. + spi0 + pins: spi0_mclk, spi0_cs0, spi0_cs1, spi0_cs2, spi0_dout, spi0_din. + spi1 + pins: spi1_mclk, spi1_cs0, spi1_cs1, spi1_cs2, spi1_dout, spi1_din. + uart + pins: uart0_txd, uart0_rxd, uart0_rts, uart0_cts, + uart1_txd, uart1_rxd. + drive_i2s + pins: clk_out1, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, + i2s_lrclk_out, i2s_bclk_out, i2s_mclk. + drive_pdm + pins: clk_out0, pdm_b, pdm_a. + drive_scb0 + pins: scb0_sclk, scb0_sdat, pdm_d, pdm_c. + drive_sdio + pins: sdio_clk, sdio_cmd, sdio_d0, sdio_d1, sdio_d2, sdio_d3, + sdh_wp, sdh_cd, sdh_clk_in. + + convenience groups: + + These are just convenient groupings of pins and don't support any drive + configs. + + uart0 + pins: uart0_cts, uart0_rts, uart0_rxd, uart0_txd. + uart1 + pins: uart1_rxd, uart1_txd. + scb0 + pins: scb0_sclk, scb0_sdat. + i2s + pins: i2s_bclk_out, i2s_din, i2s_dout0, i2s_dout1, i2s_dout2, + i2s_lrclk_out, i2s_mclk. + +Example: + + pinctrl: pinctrl@02005800 { + #gpio-range-cells = <3>; + compatible = "img,tz1090-pinctrl"; + reg = <0x02005800 0xe4>; + }; + +Example board file extract: + + &pinctrl { + uart0_default: uart0 { + uart0_cfg { + tz1090,pins = "uart0_rxd", + "uart0_txd"; + tz1090,function = "perip"; + }; + }; + tft_default: tft { + tft_cfg { + tz1090,pins = "tft"; + tz1090,function = "tft"; + }; + }; + }; + + uart@02004b00 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_default>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt index a648aaad6110..50ec3512a292 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,dove-pinctrl.txt @@ -10,29 +10,31 @@ Required properties: Available mpp pins/groups and functions: Note: brackets (x) are not part of the mpp name for marvell,function and given only for more detailed description in this document. +Note: pmu* also allows for Power Management functions listed below name pins functions ================================================================================ -mpp0 0 gpio, pmu, uart2(rts), sdio0(cd), lcd0(pwm) -mpp1 1 gpio, pmu, uart2(cts), sdio0(wp), lcd1(pwm) +mpp0 0 gpio, pmu, uart2(rts), sdio0(cd), lcd0(pwm), pmu* +mpp1 1 gpio, pmu, uart2(cts), sdio0(wp), lcd1(pwm), pmu* mpp2 2 gpio, pmu, uart2(txd), sdio0(buspwr), sata(prsnt), - uart1(rts) + uart1(rts), pmu* mpp3 3 gpio, pmu, uart2(rxd), sdio0(ledctrl), sata(act), - uart1(cts), lcd-spi(cs1) -mpp4 4 gpio, pmu, uart3(rts), sdio1(cd), spi1(miso) -mpp5 5 gpio, pmu, uart3(cts), sdio1(wp), spi1(cs) -mpp6 6 gpio, pmu, uart3(txd), sdio1(buspwr), spi1(mosi) -mpp7 7 gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck) -mpp8 8 gpio, pmu, watchdog(rstout) -mpp9 9 gpio, pmu, pex1(clkreq) -mpp10 10 gpio, pmu, ssp(sclk) + uart1(cts), lcd-spi(cs1), pmu* +mpp4 4 gpio, pmu, uart3(rts), sdio1(cd), spi1(miso), pmu* +mpp5 5 gpio, pmu, uart3(cts), sdio1(wp), spi1(cs), pmu* +mpp6 6 gpio, pmu, uart3(txd), sdio1(buspwr), spi1(mosi), pmu* +mpp7 7 gpio, pmu, uart3(rxd), sdio1(ledctrl), spi1(sck), pmu* +mpp8 8 gpio, pmu, watchdog(rstout), pmu* +mpp9 9 gpio, pmu, pex1(clkreq), pmu* +mpp10 10 gpio, pmu, ssp(sclk), pmu* mpp11 11 gpio, pmu, sata(prsnt), sata-1(act), sdio0(ledctrl), - sdio1(ledctrl), pex0(clkreq) -mpp12 12 gpio, pmu, uart2(rts), audio0(extclk), sdio1(cd), sata(act) + sdio1(ledctrl), pex0(clkreq), pmu* +mpp12 12 gpio, pmu, uart2(rts), audio0(extclk), sdio1(cd), + sata(act), pmu* mpp13 13 gpio, pmu, uart2(cts), audio1(extclk), sdio1(wp), - ssp(extclk) -mpp14 14 gpio, pmu, uart2(txd), sdio1(buspwr), ssp(rxd) -mpp15 15 gpio, pmu, uart2(rxd), sdio1(ledctrl), ssp(sfrm) + ssp(extclk), pmu* +mpp14 14 gpio, pmu, uart2(txd), sdio1(buspwr), ssp(rxd), pmu* +mpp15 15 gpio, pmu, uart2(rxd), sdio1(ledctrl), ssp(sfrm), pmu* mpp16 16 gpio, uart3(rts), sdio0(cd), ac97(sdi1), lcd-spi(cs1) mpp17 17 gpio, uart3(cts), sdio0(wp), ac97(sdi2), twsi(sda), ac97-1(sysclko) @@ -57,6 +59,21 @@ mpp_nand 64-71 gpo, nand audio0 - i2s, ac97 twsi - none, opt1, opt2, opt3 +Power Management functions (pmu*): +pmu-nc Pin not driven by any PM function +pmu-low Pin driven low (0) +pmu-high Pin driven high (1) +pmic(sdi) Pin is used for PMIC SDI +cpu-pwr-down Pin is used for CPU_PWRDWN +standby-pwr-down Pin is used for STBY_PWRDWN +core-pwr-good Pin is used for CORE_PWR_GOOD (Pins 0-7 only) +cpu-pwr-good Pin is used for CPU_PWR_GOOD (Pins 8-15 only) +bat-fault Pin is used for BATTERY_FAULT +ext0-wakeup Pin is used for EXT0_WU +ext1-wakeup Pin is used for EXT0_WU +ext2-wakeup Pin is used for EXT0_WU +pmu-blink Pin is used for blink function + Notes: * group "mpp_audio1" allows the following functions and gpio pins: - gpio : gpio on pins 52-57 diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index c95ea8278f87..aeb3c995cc04 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -126,3 +126,51 @@ device; they may be grandchildren, for example. Whether this is legal, and whether there is any interaction between the child and intermediate parent nodes, is again defined entirely by the binding for the individual pin controller device. + +== Using generic pinconfig options == + +Generic pinconfig parameters can be used by defining a separate node containing +the applicable parameters (and optional values), like: + +pcfg_pull_up: pcfg_pull_up { + bias-pull-up; + drive-strength = <20>; +}; + +This node should then be referenced in the appropriate pinctrl node as a phandle +and parsed in the driver using the pinconf_generic_parse_dt_config function. + +Supported configuration parameters are: + +bias-disable - disable any pin bias +bias-high-impedance - high impedance mode ("third-state", "floating") +bias-bus-hold - latch weakly +bias-pull-up - pull up the pin +bias-pull-down - pull down the pin +bias-pull-pin-default - use pin-default pull state +drive-push-pull - drive actively high and low +drive-open-drain - drive with open drain +drive-open-source - drive with open source +drive-strength - sink or source at most X mA +input-schmitt-enable - enable schmitt-trigger mode +input-schmitt-disable - disable schmitt-trigger mode +input-debounce - debounce mode with debound time X +low-power-enable - enable low power mode +low-power-disable - disable low power mode +output-low - set the pin to output mode with low level +output-high - set the pin to output mode with high level + +Arguments for parameters: + +- bias-pull-up, -down and -pin-default take as optional argument on hardware + supporting it the pull strength in Ohm. bias-disable will disable the pull. + +- drive-strength takes as argument the target strength in mA. + +- input-debounce takes the debounce time in usec as argument + or 0 to disable debouncing + +All parameters not listed here, do not take an argument. + +More in-depth documentation on these parameters can be found in +<include/linux/pinctrl/pinconfig-generic.h> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt index 08f0c3d01575..5a02e30dd262 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt @@ -18,7 +18,8 @@ Optional properties: pin functions is ignored - pinctrl-single,bit-per-mux : boolean to indicate that one register controls - more than one pin + more than one pin, for which "pinctrl-single,function-mask" property specifies + position mask of pin. - pinctrl-single,drive-strength : array of value that are used to configure drive strength in the pinmux register. They're value of drive strength diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt new file mode 100644 index 000000000000..05bf82a07dfd --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-st.txt @@ -0,0 +1,110 @@ +*ST pin controller. + +Each multi-function pin is controlled, driven and routed through the +PIO multiplexing block. Each pin supports GPIO functionality (ALT0) +and multiple alternate functions(ALT1 - ALTx) that directly connect +the pin to different hardware blocks. + +When a pin is in GPIO mode, Output Enable (OE), Open Drain(OD), and +Pull Up (PU) are driven by the related PIO block. + +ST pinctrl driver controls PIO multiplexing block and also interacts with +gpio driver to configure a pin. + +Required properties: (PIO multiplexing block) +- compatible : should be "st,<SOC>-<pio-block>-pinctrl" + like st,stih415-sbc-pinctrl, st,stih415-front-pinctrl and so on. +- gpio-controller : Indicates this device is a GPIO controller +- #gpio-cells : Should be one. The first cell is the pin number. +- st,retime-pin-mask : Should be mask to specify which pins can be retimed. + If the property is not present, it is assumed that all the pins in the + bank are capable of retiming. Retiming is mainly used to improve the + IO timing margins of external synchronous interfaces. +- st,bank-name : Should be a name string for this bank as + specified in datasheet. +- st,syscfg : Should be a phandle of the syscfg node. + +Example: + pin-controller-sbc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stih415-sbc-pinctrl"; + st,syscfg = <&syscfg_sbc>; + ranges = <0 0xfe610000 0x5000>; + PIO0: gpio@fe610000 { + gpio-controller; + #gpio-cells = <1>; + reg = <0 0x100>; + st,bank-name = "PIO0"; + }; + ... + pin-functions nodes follow... + }; + + +Contents of function subnode node: +---------------------- +Required properties for pin configuration node: +- st,pins : Child node with list of pins with configuration. + +Below is the format of how each pin conf should look like. + +<bank offset mux mode rt_type rt_delay rt_clk> + +Every PIO is represented with 4-7 parameters depending on retime configuration. +Each parameter is explained as below. + +-bank : Should be bank phandle to which this PIO belongs. +-offset : Offset in the PIO bank. +-mux : Should be alternate function number associated this pin. + Use same numbers from datasheet. +-mode :pin configuration is selected from one of the below values. + IN + IN_PU + OUT + BIDIR + BIDIR_PU + +-rt_type Retiming Configuration for the pin. + Possible retime configuration are: + + ------- ------------- + value args + ------- ------------- + NICLK <delay> <clk> + ICLK_IO <delay> <clk> + BYPASS <delay> + DE_IO <delay> <clk> + SE_ICLK_IO <delay> <clk> + SE_NICLK_IO <delay> <clk> + +- delay is retime delay in pico seconds as mentioned in data sheet. + +- rt_clk :clk to be use for retime. + Possible values are: + CLK_A + CLK_B + CLK_C + CLK_D + +Example of mmcclk pin which is a bi-direction pull pu with retime config +as non inverted clock retimed with CLK_B and delay of 0 pico seconds: + +pin-controller { + ... + mmc0 { + pinctrl_mmc: mmc { + st,pins { + mmcclk = <&PIO13 4 ALT4 BIDIR_PU NICLK 0 CLK_B>; + ... + }; + }; + ... + }; +}; + +sdhci0:sdhci@fe810000{ + ... + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt new file mode 100644 index 000000000000..d5dac7b843a9 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -0,0 +1,153 @@ +* Renesas Pin Function Controller (GPIO and Pin Mux/Config) + +The Pin Function Controller (PFC) is a Pin Mux/Config controller. On SH7372, +SH73A0, R8A73A4 and R8A7740 it also acts as a GPIO controller. + + +Pin Control +----------- + +Required Properties: + + - compatible: should be one of the following. + - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. + - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. + - "renesas,pfc-r8a7778": for R8A7778 (R-Mobile M1) compatible pin-controller. + - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller. + - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller. + - "renesas,pfc-sh7372": for SH7372 (SH-Mobile AP4) compatible pin-controller. + - "renesas,pfc-sh73a0": for SH73A0 (SH-Mobile AG5) compatible pin-controller. + + - reg: Base address and length of each memory resource used by the pin + controller hardware module. + +Optional properties: + + - #gpio-range-cells: Mandatory when the PFC doesn't handle GPIO, forbidden + otherwise. Should be 3. + +The PFC node also acts as a container for pin configuration nodes. Please refer +to pinctrl-bindings.txt in this directory for the definition of the term "pin +configuration node" and for the common pinctrl bindings used by client devices. + +Each pin configuration node represents a desired configuration for a pin, a +pin group, or a list of pins or pin groups. The configuration can include the +function to select on those pin(s) and pin configuration parameters (such as +pull-up and pull-down). + +Pin configuration nodes contain pin configuration properties, either directly +or grouped in child subnodes. Both pin muxing and configuration parameters can +be grouped in that way and referenced as a single pin configuration node by +client devices. + +A configuration node or subnode must reference at least one pin (through the +pins or pin groups properties) and contain at least a function or one +configuration parameter. When the function is present only pin groups can be +used to reference pins. + +All pin configuration nodes and subnodes names are ignored. All of those nodes +are parsed through phandles and processed purely based on their content. + +Pin Configuration Node Properties: + +- renesas,pins : An array of strings, each string containing the name of a pin. +- renesas,groups : An array of strings, each string containing the name of a pin + group. + +- renesas,function: A string containing the name of the function to mux to the + pin group(s) specified by the renesas,groups property + + Valid values for pin, group and function names can be found in the group and + function arrays of the PFC data file corresponding to the SoC + (drivers/pinctrl/sh-pfc/pfc-*.c) + +The pin configuration parameters use the generic pinconf bindings defined in +pinctrl-bindings.txt in this directory. The supported parameters are +bias-disable, bias-pull-up and bias-pull-down. + + +GPIO +---- + +On SH7372, SH73A0, R8A73A4 and R8A7740 the PFC node is also a GPIO controller +node. + +Required Properties: + + - gpio-controller: Marks the device node as a gpio controller. + + - #gpio-cells: Should be 2. The first cell is the GPIO number and the second + cell specifies GPIO flags, as defined in <dt-bindings/gpio/gpio.h>. Only the + GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported. + +The syntax of the gpio specifier used by client nodes should be the following +with values derived from the SoC user manual. + + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [flags]> + +On other mach-shmobile platforms GPIO is handled by the gpio-rcar driver. +Please refer to Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +for documentation of the GPIO device tree bindings on those platforms. + + +Examples +-------- + +Example 1: SH73A0 (SH-Mobile AG5) pin controller node + + pfc: pfc@e6050000 { + compatible = "renesas,pfc-sh73a0"; + reg = <0xe6050000 0x8000>, + <0xe605801c 0x1c>; + gpio-controller; + #gpio-cells = <2>; + }; + +Example 2: A GPIO LED node that references a GPIO + + #include <dt-bindings/gpio/gpio.h> + + leds { + compatible = "gpio-leds"; + led1 { + gpios = <&pfc 20 GPIO_ACTIVE_LOW>; + }; + }; + +Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps + for the MMCIF and SCIFA4 devices + + &pfc { + pinctrl-0 = <&scifa4_pins>; + pinctrl-names = "default"; + + mmcif_pins: mmcif { + mux { + renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; + renesas,function = "mmc0"; + }; + cfg { + renesas,groups = "mmc0_data8_0"; + renesas,pins = "PORT279"; + bias-pull-up; + }; + }; + + scifa4_pins: scifa4 { + renesas,groups = "scifa4_data", "scifa4_ctrl"; + renesas,function = "scifa4"; + }; + }; + +Example 4: KZM-A9-GT (SH-Mobile AG5) default pin state for the MMCIF device + + &mmcif { + pinctrl-0 = <&mmcif_pins>; + pinctrl-names = "default"; + + bus-width = <8>; + vmmc-supply = <®_1p8v>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt new file mode 100644 index 000000000000..b0fb1018d7ad --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -0,0 +1,97 @@ +* Rockchip Pinmux Controller + +The Rockchip Pinmux Controller, enables the IC +to share one PAD to several functional blocks. The sharing is done by +multiplexing the PAD input/output signals. For each PAD there are up to +4 muxing options with option 0 being the use as a GPIO. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The Rockchip pin configuration node is a node of a group of pins which can be +used for a specific device or function. This node represents both mux and +config of the pins in that group. The 'pins' selects the function mode(also +named pin mode) this pin can work on and the 'config' configures various pad +settings such as pull-up, etc. + +The pins are grouped into up to 5 individual pin banks which need to be +defined as gpio sub-nodes of the pinmux controller. + +Required properties for iomux controller: + - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" + "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" + +Required properties for gpio sub nodes: + - compatible: "rockchip,gpio-bank" + - reg: register of the gpio bank (different than the iomux registerset) + - interrupts: base interrupt of the gpio bank in the interrupt controller + - clocks: clock that drives this bank + - gpio-controller: identifies the node as a gpio controller and pin bank. + - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See generic + GPIO binding documentation for description of particular cells. + - interrupt-controller: identifies the controller node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2 and the interrupt + cells should use the standard two-cell scheme described in + bindings/interrupt-controller/interrupts.txt + +Required properties for pin configuration node: + - rockchip,pins: 3 integers array, represents a group of pins mux and config + setting. The format is rockchip,pins = <PIN_BANK PIN_BANK_IDX MUX &phandle>. + The MUX 0 means gpio and MUX 1 to 3 mean the specific device function. + The phandle of a node containing the generic pinconfig options + to use, as described in pinctrl-bindings.txt in this directory. + +Examples: + +#include <dt-bindings/pinctrl/rockchip.h> + +... + +pinctrl@20008000 { + compatible = "rockchip,rk3066a-pinctrl"; + reg = <0x20008000 0x150>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0@20034000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20034000 0x100>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_gates8 9>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + ... + + pcfg_pull_default: pcfg_pull_default { + bias-pull-pin-default + }; + + uart2 { + uart2_xfer: uart2-xfer { + rockchip,pins = <RK_GPIO1 8 1 &pcfg_pull_default>, + <RK_GPIO1 9 1 &pcfg_pull_default>; + }; + }; +}; + +uart2: serial@20064000 { + compatible = "snps,dw-apb-uart"; + reg = <0x20064000 0x400>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&mux_uart2>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&uart2_xfer>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt new file mode 100644 index 000000000000..e3865e136067 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/ste,abx500.txt @@ -0,0 +1,352 @@ +ST Ericsson abx500 pinmux controller + +Required properties: +- compatible: "stericsson,ab8500-gpio", "stericsson,ab8540-gpio", + "stericsson,ab8505-gpio", "stericsson,ab9540-gpio", + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +ST Ericsson's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as input, output, pull up, pull down... + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Required subnode-properties: +- ste,pins : An array of strings. Each string contains the name of a pin or + group. + +Optional subnode-properties: +- ste,function: A string containing the name of the function to mux to the + pin or group. + +- generic pin configuration option to use. Example : + + default_cfg { + ste,pins = "GPIO1"; + bias-disable; + }; + +- ste,config: Handle of pin configuration node containing the generic + pinconfig options to use, as described in pinctrl-bindings.txt in + this directory. Example : + + pcfg_bias_disable: pcfg_bias_disable { + bias-disable; + }; + + default_cfg { + ste,pins = "GPIO1"; + ste.config = <&pcfg_bias_disable>; + }; + +Example board file extract: + +&pinctrl_abx500 { + pinctrl-names = "default"; + pinctrl-0 = <&sysclkreq2_default_mode>, <&sysclkreq3_default_mode>, <&gpio3_default_mode>, <&sysclkreq6_default_mode>, <&pwmout1_default_mode>, <&pwmout2_default_mode>, <&pwmout3_default_mode>, <&adi1_default_mode>, <&dmic12_default_mode>, <&dmic34_default_mode>, <&dmic56_default_mode>, <&sysclkreq5_default_mode>, <&batremn_default_mode>, <&service_default_mode>, <&pwrctrl0_default_mode>, <&pwrctrl1_default_mode>, <&pwmextvibra1_default_mode>, <&pwmextvibra2_default_mode>, <&gpio51_default_mode>, <&gpio52_default_mode>, <&gpio53_default_mode>, <&gpio54_default_mode>, <&pdmclkdat_default_mode>; + + sysclkreq2 { + sysclkreq2_default_mode: sysclkreq2_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq2_d_1"; + }; + default_cfg { + ste,pins = "GPIO1"; + bias-disable; + }; + }; + }; + sysclkreq3 { + sysclkreq3_default_mode: sysclkreq3_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq3_d_1"; + }; + default_cfg { + ste,pins = "GPIO2"; + output-low; + }; + }; + }; + gpio3 { + gpio3_default_mode: gpio3_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio3_a_1"; + }; + default_cfg { + ste,pins = "GPIO3"; + output-low; + }; + }; + }; + sysclkreq6 { + sysclkreq6_default_mode: sysclkreq6_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq6_d_1"; + }; + default_cfg { + ste,pins = "GPIO4"; + bias-disable; + }; + }; + }; + pwmout1 { + pwmout1_default_mode: pwmout1_default { + default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout1_d_1"; + }; + default_cfg { + ste,pins = "GPIO14"; + output-low; + }; + }; + }; + pwmout2 { + pwmout2_default_mode: pwmout2_default { + pwmout2_default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout2_d_1"; + }; + pwmout2_default_cfg { + ste,pins = "GPIO15"; + output-low; + }; + }; + }; + pwmout3 { + pwmout3_default_mode: pwmout3_default { + pwmout3_default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout3_d_1"; + }; + pwmout3_default_cfg { + ste,pins = "GPIO16"; + output-low; + }; + }; + }; + adi1 { + + adi1_default_mode: adi1_default { + adi1_default_mux { + ste,function = "adi1"; + ste,pins = "adi1_d_1"; + }; + adi1_default_cfg1 { + ste,pins = "GPIO17","GPIO19","GPIO20"; + bias-disable; + }; + adi1_default_cfg2 { + ste,pins = "GPIO18"; + output-low; + }; + }; + }; + dmic12 { + dmic12_default_mode: dmic12_default { + dmic12_default_mux { + ste,function = "dmic"; + ste,pins = "dmic12_d_1"; + }; + dmic12_default_cfg1 { + ste,pins = "GPIO27"; + output-low; + }; + dmic12_default_cfg2 { + ste,pins = "GPIO28"; + bias-disable; + }; + }; + }; + dmic34 { + dmic34_default_mode: dmic34_default { + dmic34_default_mux { + ste,function = "dmic"; + ste,pins = "dmic34_d_1"; + }; + dmic34_default_cfg1 { + ste,pins = "GPIO29"; + output-low; + }; + dmic34_default_cfg2 { + ste,pins = "GPIO30"; + bias-disable;{ + + }; + }; + }; + dmic56 { + dmic56_default_mode: dmic56_default { + dmic56_default_mux { + ste,function = "dmic"; + ste,pins = "dmic56_d_1"; + }; + dmic56_default_cfg1 { + ste,pins = "GPIO31"; + output-low; + }; + dmic56_default_cfg2 { + ste,pins = "GPIO32"; + bias-disable; + }; + }; + }; + sysclkreq5 { + sysclkreq5_default_mode: sysclkreq5_default { + sysclkreq5_default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq5_d_1"; + }; + sysclkreq5_default_cfg { + ste,pins = "GPIO42"; + output-low; + }; + }; + }; + batremn { + batremn_default_mode: batremn_default { + batremn_default_mux { + ste,function = "batremn"; + ste,pins = "batremn_d_1"; + }; + batremn_default_cfg { + ste,pins = "GPIO43"; + bias-disable; + }; + }; + }; + service { + service_default_mode: service_default { + service_default_mux { + ste,function = "service"; + ste,pins = "service_d_1"; + }; + service_default_cfg { + ste,pins = "GPIO44"; + bias-disable; + }; + }; + }; + pwrctrl0 { + pwrctrl0_default_mux: pwrctrl0_mux { + pwrctrl0_default_mux { + ste,function = "pwrctrl"; + ste,pins = "pwrctrl0_d_1"; + }; + }; + pwrctrl0_default_mode: pwrctrl0_default { + pwrctrl0_default_cfg { + ste,pins = "GPIO45"; + bias-disable; + }; + }; + }; + pwrctrl1 { + pwrctrl1_default_mux: pwrctrl1_mux { + pwrctrl1_default_mux { + ste,function = "pwrctrl"; + ste,pins = "pwrctrl1_d_1"; + }; + }; + pwrctrl1_default_mode: pwrctrl1_default { + pwrctrl1_default_cfg { + ste,pins = "GPIO46"; + bias-disable; + }; + }; + }; + pwmextvibra1 { + pwmextvibra1_default_mode: pwmextvibra1_default { + pwmextvibra1_default_mux { + ste,function = "pwmextvibra"; + ste,pins = "pwmextvibra1_d_1"; + }; + pwmextvibra1_default_cfg { + ste,pins = "GPIO47"; + bias-disable; + }; + }; + }; + pwmextvibra2 { + pwmextvibra2_default_mode: pwmextvibra2_default { + pwmextvibra2_default_mux { + ste,function = "pwmextvibra"; + ste,pins = "pwmextvibra2_d_1"; + }; + pwmextvibra1_default_cfg { + ste,pins = "GPIO48"; + bias-disable; + }; + }; + }; + gpio51 { + gpio51_default_mode: gpio51_default { + gpio51_default_mux { + ste,function = "gpio"; + ste,pins = "gpio51_a_1"; + }; + gpio51_default_cfg { + ste,pins = "GPIO51"; + output-low; + }; + }; + }; + gpio52 { + gpio52_default_mode: gpio52_default { + gpio52_default_mux { + ste,function = "gpio"; + ste,pins = "gpio52_a_1"; + }; + gpio52_default_cfg { + ste,pins = "GPIO52"; + bias-pull-down; + }; + }; + }; + gpio53 { + gpio53_default_mode: gpio53_default { + gpio53_default_mux { + ste,function = "gpio"; + ste,pins = "gpio53_a_1"; + }; + gpio53_default_cfg { + ste,pins = "GPIO53"; + bias-pull-down; + }; + }; + }; + gpio54 { + gpio54_default_mode: gpio54_default { + gpio54_default_mux { + ste,function = "gpio"; + ste,pins = "gpio54_a_1"; + }; + gpio54_default_cfg { + ste,pins = "GPIO54"; + output-low; + }; + }; + }; + pdmclkdat { + pdmclkdat_default_mode: pdmclkdat_default { + pdmclkdat_default_mux { + ste,function = "pdm"; + ste,pins = "pdmclkdat_d_1"; + }; + pdmclkdat_default_cfg { + ste,pins = "GPIO55", "GPIO56"; + bias-disable; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt new file mode 100644 index 000000000000..2246bc5c874b --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/lp8727_charger.txt @@ -0,0 +1,44 @@ +Binding for TI/National Semiconductor LP8727 Charger + +Required properties: +- compatible: "ti,lp8727" +- reg: I2C slave address 27h + +Optional properties: +- interrupt-parent: interrupt controller node (see interrupt binding[0]) +- interrupts: interrupt specifier (see interrupt binding[0]) +- debounce-ms: interrupt debounce time. (u32) + +AC and USB charging parameters +- charger-type: "ac" or "usb" (string) +- eoc-level: value of 'enum lp8727_eoc_level' (u8) +- charging-current: value of 'enum lp8727_ichg' (u8) + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example) + +lp8727@27 { + compatible = "ti,lp8727"; + reg = <0x27>; + + /* GPIO 134 is used for LP8728 interrupt pin */ + interrupt-parent = <&gpio5>; /* base = 128 */ + interrupts = <6 0x2>; /* offset = 6, falling edge type */ + + debounce-ms = <300>; + + /* AC charger: 5% EOC and 500mA charging current */ + ac { + charger-type = "ac"; + eoc-level = /bits/ 8 <0>; + charging-current = /bits/ 8 <4>; + }; + + /* USB charger: 10% EOC and 400mA charging current */ + usb { + charger-type = "usb"; + eoc-level = /bits/ 8 <1>; + charging-current = /bits/ 8 <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt index 2161334a7ca5..712baf6c3e24 100644 --- a/Documentation/devicetree/bindings/powerpc/4xx/emac.txt +++ b/Documentation/devicetree/bindings/powerpc/4xx/emac.txt @@ -1,7 +1,7 @@ 4xx/Axon EMAC ethernet nodes The EMAC ethernet controller in IBM and AMCC 4xx chips, and also - the Axon bridge. To operate this needs to interact with a ths + the Axon bridge. To operate this needs to interact with a this special McMAL DMA controller, and sometimes an RGMII or ZMII interface. In addition to the nodes and properties described below, the node for the OPB bus on which the EMAC sits must have a diff --git a/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt b/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt new file mode 100644 index 000000000000..641bc13983e1 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/interlaken-lac.txt @@ -0,0 +1,309 @@ +=============================================================================== +Freescale Interlaken Look-Aside Controller Device Bindings +Copyright 2012 Freescale Semiconductor Inc. + +CONTENTS + - Interlaken Look-Aside Controller (LAC) Node + - Example LAC Node + - Interlaken Look-Aside Controller (LAC) Software Portal Node + - Interlaken Look-Aside Controller (LAC) Software Portal Child Nodes + - Example LAC SWP Node with Child Nodes + +============================================================================== +Interlaken Look-Aside Controller (LAC) Node + +DESCRIPTION + +The Interlaken is a narrow, high speed channelized chip-to-chip interface. To +facilitate interoperability between a data path device and a look-aside +co-processor, the Interlaken Look-Aside protocol is defined for short +transaction-related transfers. Although based on the Interlaken protocol, +Interlaken Look-Aside is not directly compatible with Interlaken and can be +considered a different operation mode. + +The Interlaken LA controller connects internal platform to Interlaken serial +interface. It accepts LA command through software portals, which are system +memory mapped 4KB spaces. The LA commands are then translated into the +Interlaken control words and data words, which are sent on TX side to TCAM +through SerDes lanes. + +There are two 4KiB spaces defined within the LAC global register memory map. +There is a full register set at 0x0000-0x0FFF (also known as the "hypervisor" +version), and a subset at 0x1000-0x1FFF. The former is a superset of the +latter, and includes certain registers that should not be accessible to +partitioned software. Separate nodes are used for each region, with a phandle +linking the hypervisor node to the normal operating node. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,interlaken-lac". This represents only + those LAC CCSR registers not protected in partitioned + software. The version of the device is determined by the LAC + IP Block Revision Register (IPBRR0) at offset 0x0BF8. + + Table of correspondences between IPBRR0 values and example + chips: + Value Device + ----------- ------- + 0x02000100 T4240 + + The Hypervisor node has a different compatible. It must include + "fsl,interlaken-lac-hv". This node represents the protected + LAC register space and is required except inside a partition + where access to the hypervisor node is to be denied. + + - fsl,non-hv-node + Usage: required in "fsl,interlaken-lac-hv" + Value type: <phandle> + Definition: Points to the non-protected LAC CCSR mapped register space + node. + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The first resource represents the + Interlaken LAC configuration registers. + + - interrupts: + Usage: required in non-hv node only + Value type: <prop-encoded-array> + Definition: Interrupt mapping for Interlaken LAC error IRQ. + +EXAMPLE + lac: lac@229000 { + compatible = "fsl,interlaken-lac" + reg = <0x229000 0x1000>; + interrupts = <16 2 1 18>; + }; + + lac-hv@228000 { + compatible = "fsl,interlaken-lac-hv" + reg = <0x228000 0x1000>; + fsl,non-hv-node = <&lac>; + }; + +=============================================================================== +Interlaken Look-Aside Controller (LAC) Software Portal Container Node + +DESCRIPTION +The Interlaken Look-Aside Controller (LAC) utilizes Software Portals to accept +Interlaken Look-Aside (ILA) commands. The Interlaken LAC software portal +memory map occupies 128KB of memory space. The software portal memory space is +intended to be cache-enabled. WIMG for each software space is required to be +0010 if stashing is enabled; otherwise, WIMG can be 0000 or 0010. + +PROPERTIES + + - #address-cells + Usage: required + Value type: <u32> + Definition: A standard property. Must have a value of 1. + + - #size-cells + Usage: required + Value type: <u32> + Definition: A standard property. Must have a value of 1. + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,interlaken-lac-portals" + + - ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the address and length + of the LAC portal memory space. + +=============================================================================== +Interlaken Look-Aside Controller (LAC) Software Portals Child Nodes + +DESCRIPTION +There are up to 24 available software portals with each software portal +requiring 4KB of consecutive memory within the software portal memory mapped +space. + +PROPERTIES + + - compatible + Usage: required + Value type: <string> + Definition: Must include "fsl,interlaken-lac-portal-vX.Y" where X is + the Major version (IP_MJ) found in the LAC IP Block Revision + Register (IPBRR0), at offset 0x0BF8, and Y is the Minor version + (IP_MN). + + Table of correspondences between version values and example chips: + Value Device + ------ ------- + 1.0 T4240 + + - reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. The first resource represents the + Interlaken LAC software portal registers. + + - fsl,liodn + Value type: <u32> + Definition: The logical I/O device number (LIODN) for this device. The + LIODN is a number expressed by this device and used to perform + look-ups in the IOMMU (PAMU) address table when performing + DMAs. This property is automatically added by u-boot. + +=============================================================================== +EXAMPLE + +lac-portals { + #address-cells = <0x1>; + #size-cells = <0x1>; + compatible = "fsl,interlaken-lac-portals"; + ranges = <0x0 0xf 0xf4400000 0x20000>; + + lportal0: lac-portal@0 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x204>; + reg = <0x0 0x1000>; + }; + + lportal1: lac-portal@1000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x205>; + reg = <0x1000 0x1000>; + }; + + lportal2: lac-portal@2000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x206>; + reg = <0x2000 0x1000>; + }; + + lportal3: lac-portal@3000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x207>; + reg = <0x3000 0x1000>; + }; + + lportal4: lac-portal@4000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x208>; + reg = <0x4000 0x1000>; + }; + + lportal5: lac-portal@5000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x209>; + reg = <0x5000 0x1000>; + }; + + lportal6: lac-portal@6000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x20A>; + reg = <0x6000 0x1000>; + }; + + lportal7: lac-portal@7000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x20B>; + reg = <0x7000 0x1000>; + }; + + lportal8: lac-portal@8000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x20C>; + reg = <0x8000 0x1000>; + }; + + lportal9: lac-portal@9000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x20D>; + reg = <0x9000 0x1000>; + }; + + lportal10: lac-portal@A000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x20E>; + reg = <0xA000 0x1000>; + }; + + lportal11: lac-portal@B000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x20F>; + reg = <0xB000 0x1000>; + }; + + lportal12: lac-portal@C000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x210>; + reg = <0xC000 0x1000>; + }; + + lportal13: lac-portal@D000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x211>; + reg = <0xD000 0x1000>; + }; + + lportal14: lac-portal@E000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x212>; + reg = <0xE000 0x1000>; + }; + + lportal15: lac-portal@F000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x213>; + reg = <0xF000 0x1000>; + }; + + lportal16: lac-portal@10000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x214>; + reg = <0x10000 0x1000>; + }; + + lportal17: lac-portal@11000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x215>; + reg = <0x11000 0x1000>; + }; + + lportal8: lac-portal@1200 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x216>; + reg = <0x12000 0x1000>; + }; + + lportal19: lac-portal@13000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x217>; + reg = <0x13000 0x1000>; + }; + + lportal20: lac-portal@14000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x218>; + reg = <0x14000 0x1000>; + }; + + lportal21: lac-portal@15000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x219>; + reg = <0x15000 0x1000>; + }; + + lportal22: lac-portal@16000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x21A>; + reg = <0x16000 0x1000>; + }; + + lportal23: lac-portal@17000 { + compatible = "fsl,interlaken-lac-portal-v1.0"; + fsl,liodn = <0x21B>; + reg = <0x17000 0x1000>; + }; +}; diff --git a/Documentation/devicetree/bindings/pps/pps-gpio.txt b/Documentation/devicetree/bindings/pps/pps-gpio.txt new file mode 100644 index 000000000000..40bf9c3564a5 --- /dev/null +++ b/Documentation/devicetree/bindings/pps/pps-gpio.txt @@ -0,0 +1,20 @@ +Device-Tree Bindings for a PPS Signal on GPIO + +These properties describe a PPS (pulse-per-second) signal connected to +a GPIO pin. + +Required properties: +- compatible: should be "pps-gpio" +- gpios: one PPS GPIO in the format described by ../gpio/gpio.txt + +Optional properties: +- assert-falling-edge: when present, assert is indicated by a falling edge + (instead of by a rising edge) + +Example: + pps { + compatible = "pps-gpio"; + gpios = <&gpio2 6 0>; + + assert-falling-edge; + }; diff --git a/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt new file mode 100644 index 000000000000..1e3dfe7a4894 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/nxp,pca9685-pwm.txt @@ -0,0 +1,27 @@ +NXP PCA9685 16-channel 12-bit PWM LED controller +================================================ + +Required properties: + - compatible: "nxp,pca9685-pwm" + - #pwm-cells: should be 2. The first cell specifies the per-chip index + of the PWM to use and the second cell is the period in nanoseconds. + The index 16 is the ALLCALL channel, that sets all PWM channels at the same + time. + +Optional properties: + - invert (bool): boolean to enable inverted logic + - open-drain (bool): boolean to configure outputs with open-drain structure; + if omitted use totem-pole structure + +Example: + +For LEDs that are directly connected to the PCA, the following setting is +applicable: + +pca: pca@41 { + compatible = "nxp,pca9685-pwm"; + #pwm-cells = <2>; + reg = <0x41>; + invert; + open-drain; +}; diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt new file mode 100644 index 000000000000..78183182dad9 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -0,0 +1,160 @@ +Binding for TI/National Semiconductor LP872x Driver + +Required properties: + - compatible: "ti,lp8720" or "ti,lp8725" + - reg: I2C slave address. 0x7d = LP8720, 0x7a = LP8725 + +Optional properties: + - ti,general-config: the value of LP872X_GENERAL_CFG register (u8) + (LP8720) + bit[2]: BUCK output voltage control by external DVS pin or register + 1 = external pin, 0 = bit7 of register 08h + bit[1]: sleep control by external DVS pin or register + 1 = external pin, 0 = bit6 of register 08h + bit[0]: time step unit(usec). 1 = 25, 0 = 50 + + (LP8725) + bit[7:6]: time step unit(usec). 00 = 32, 01 = 64, 10 = 128, 11 = 256 + bit[4]: BUCK2 enable control. 1 = enable, 0 = disable + bit[3]: BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh + bit[2]: BUCK1 output voltage control by external DVS pin or register + 1 = register 08h, 0 = DVS + bit[1]: LDO sleep control. 1 = sleep mode, 0 = normal + bit[0]: BUCK1 enable control, 1 = enable, 0 = disable + + For more details, please see the datasheet. + + - ti,update-config: define it when LP872X_GENERAL_CFG register should be set + - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. + - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. + - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + + Sub nodes for regulator_init_data + LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) + LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2) + For more details, please see the following binding document. + (Documentation/devicetree/bindings/regulator/regulator.txt) + +Datasheet + - LP8720: http://www.ti.com/lit/ds/symlink/lp8720.pdf + - LP8725: http://www.ti.com/lit/ds/symlink/lp8725.pdf + +Example 1) LP8720 + +lp8720@7d { + compatible = "ti,lp8720"; + reg = <0x7d>; + + /* external DVS pin used, timestep is 25usec */ + ti,general-config = /bits/ 8 <0x03>; + ti,update-config; + + /* + * The dvs-gpio depends on the processor environment. + * For example, following GPIO specifier means GPIO134 in OMAP4. + */ + ti,dvs-gpio = <&gpio5 6 0>; + ti,dvs-vsel = /bits/ 8 <1>; /* SEL_V2 */ + ti,dvs-state = /bits/ 8 <1>; /* DVS_HIGH */ + + vaf: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vmmc: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_io: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcam_core: ldo4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2850000>; + regulator-boot-on; + }; + + vcam: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcc: buck { + regulator-name = "VBUCK"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2300000>; + }; +}; + +Example 2) LP8725 + +lp8725@7a { + compatible = "ti,lp8725"; + reg = <0x7a>; + + /* Enable BUCK1,2, no DVS, normal LDO mode, timestep is 256usec */ + ti,general-config = /bits/ 8 <0xdd>; + ti,update-config; + + vcam_io: ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam_core: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcam: ldo3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + }; + + vcmmb_io: ldo4 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vcmmb_core: ldo5 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + vaux1: lilo1 { + regulator-name = "VAUX1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vaux2: lilo2 { + regulator-name = "VAUX2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + vcc1: buck1 { + regulator-name = "VBUCK1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; + + vcc2: buck2 { + regulator-name = "VBUCK2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3000000>; + regulator-min-microamp = <460000>; + regulator-max-microamp = <1370000>; + regulator-boot-on; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt new file mode 100644 index 000000000000..4f15d8a1bfd0 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -0,0 +1,21 @@ +* Maxim MAX8973 Voltage Regulator + +Required properties: + +- compatible: must be "maxim,max8973" +- reg: the i2c slave address of the regulator. It should be 0x1b. + +Any standard regulator properties can be used to configure the single max8973 +DCDC. + +Example: + + max8973@1b { + compatible = "maxim,max8973"; + reg = <0x1b>; + + regulator-min-microvolt = <935000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt index 9e5e51d78868..5c186a7a77ba 100644 --- a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt @@ -1,6 +1,6 @@ * Maxim MAX8997 Voltage and Current Regulator -The Maxim MAX8997 is a multi-function device which includes volatage and +The Maxim MAX8997 is a multi-function device which includes voltage and current regulators, rtc, charger controller and other sub-blocks. It is interfaced to the host controller using a i2c interface. Each sub-block is addressed by the host system using different i2c slave address. This document diff --git a/Documentation/devicetree/bindings/regulator/palmas-pmic.txt b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt new file mode 100644 index 000000000000..d5a308629c57 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/palmas-pmic.txt @@ -0,0 +1,72 @@ +* palmas regulator IP block devicetree bindings + +Required properties: +- compatible : Should be from the list + ti,twl6035-pmic + ti,twl6036-pmic + ti,twl6037-pmic + ti,tps65913-pmic + ti,tps65914-pmic +and also the generic series names + ti,palmas-pmic +- interrupt-parent : The parent interrupt controller which is palmas. +- interrupts : The interrupt number and the type which can be looked up here: + arch/arm/boot/dts/include/dt-bindings/interrupt-controller/irq.h +- interrupts-name: The names of the individual interrupts. + +Optional properties: +- ti,ldo6-vibrator : ldo6 is in vibrator mode + +Optional nodes: +- regulators : Must contain a sub-node per regulator from the list below. + Each sub-node should contain the constraints and initialization + information for that regulator. See regulator.txt for a + description of standard properties for these sub-nodes. + Additional custom properties are listed below. + + For ti,palmas-pmic - smps12, smps123, smps3 depending on OTP, + smps45, smps457, smps7 depending on variant, smps6, smps[8-10], + ldo[1-9], ldoln, ldousb. + + Optional sub-node properties: + ti,warm-reset - maintain voltage during warm reset(boolean) + ti,roof-floor - control voltage selection by pin(boolean) + ti,sleep-mode - mode to adopt in pmic sleep 0 - off, 1 - auto, + 2 - eco, 3 - forced pwm + ti,tstep - slope control 0 - Jump, 1 10mV/us, 2 5mV/us, 3 2.5mV/us + ti,smps-range - OTP has the wrong range set for the hardware so override + 0 - low range, 1 - high range. + +Example: + +#include <dt-bindings/interrupt-controller/irq.h> + +pmic { + compatible = "ti,twl6035-pmic", "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupts-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps12_reg : smps12 { + regulator-name = "smps12"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + ti,warm-reset; + ti,roof-floor; + ti,mode-sleep = <0>; + ti,tstep = <0>; + ti,smps-range = <1>; + }; + + ldo1_reg: ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index ecfc6ccd67ef..48a3b8e5d6bd 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -9,6 +9,7 @@ Optional properties: - regulator-max-microamp: largest current consumers may set - regulator-always-on: boolean, regulator should never be disabled - regulator-boot-on: bootloader/firmware enabled regulator +- regulator-allow-bypass: allow the regulator to go into bypass mode - <name>-supply: phandle to the parent supply/regulator node - regulator-ramp-delay: ramp delay for regulator(in uV/uS) diff --git a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt index a35ff99003a5..d1660a90fc06 100644 --- a/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/s5m8767-regulator.txt @@ -1,6 +1,6 @@ * Samsung S5M8767 Voltage and Current Regulator -The Samsung S5M8767 is a multi-function device which includes volatage and +The Samsung S5M8767 is a multi-function device which includes voltage and current regulators, rtc, charger controller and other sub-blocks. It is interfaced to the host controller using a i2c interface. Each sub-block is addressed by the host system using different i2c slave address. This document @@ -103,13 +103,13 @@ Example: s5m8767,pmic-buck-default-dvs-idx = <0>; - s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 1 0 0>, /* DVS1 */ - <&gpx0 1 1 0 0>, /* DVS2 */ - <&gpx0 2 1 0 0>; /* DVS3 */ + s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */ + <&gpx0 1 0>, /* DVS2 */ + <&gpx0 2 0>; /* DVS3 */ - s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>, /* SET1 */ - <&gpx2 4 1 0 0>, /* SET2 */ - <&gpx2 5 1 0 0>; /* SET3 */ + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */ + <&gpx2 4 0>, /* SET2 */ + <&gpx2 5 0>; /* SET3 */ s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, <1250000>, <1200000>, diff --git a/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt new file mode 100644 index 000000000000..2e57a33e9029 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/ti-abb-regulator.txt @@ -0,0 +1,128 @@ +Adaptive Body Bias(ABB) SoC internal LDO regulator for Texas Instruments SoCs + +Required Properties: +- compatible: Should be one of: + - "ti,abb-v1" for older SoCs like OMAP3 + - "ti,abb-v2" for newer SoCs like OMAP4, OMAP5 +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + - "base-address" - contains base address of ABB module + - "int-address" - contains address of interrupt register for ABB module + (also see Optional properties) +- #address-cell: should be 0 +- #size-cell: should be 0 +- clocks: should point to the clock node used by ABB module +- ti,settling-time: Settling time in uSecs from SoC documentation for ABB module + to settle down(target time for SR2_WTCNT_VALUE). +- ti,clock-cycles: SoC specific data about count of system ti,clock-cycles used for + computing settling time from SoC Documentation for ABB module(clock + cycles for SR2_WTCNT_VALUE). +- ti,tranxdone-status-mask: Mask to the int-register to write-to-clear mask + indicating LDO tranxdone (operation complete). +- ti,abb_info: An array of 6-tuples u32 items providing information about ABB + configuration needed per operational voltage of the device. + Each item consists of the following in the same order: + volt: voltage in uV - Only used to index ABB information. + ABB mode: one of the following: + 0-bypass + 1-Forward Body Bias(FBB) + 3-Reverse Body Bias(RBB) + efuse: (see Optional properties) + RBB enable efuse Mask: (See Optional properties) + FBB enable efuse Mask: (See Optional properties) + Vset value efuse Mask: (See Optional properties) + + NOTE: If more than 1 entry is present, then regulator is setup to change + voltage, allowing for various modes to be selected indexed off + the regulator. Further, ABB LDOs are considered always-on by + default. + +Optional Properties: +- reg-names: In addition to the required properties, the following are optional + - "efuse-address" - Contains efuse base address used to pick up ABB info. + - "ldo-address" - Contains address of ABB LDO overide register address. + "efuse-address" is required for this. +- ti,ldovbb-vset-mask - Required if ldo-address is set, mask for LDO override + register to provide override vset value. +- ti,ldovbb-override-mask - Required if ldo-address is set, mask for LDO + override register to enable override vset value. +- ti,abb_opp_sel: Addendum to the description in required properties + efuse: Mandatory if 'efuse-address' register is defined. Provides offset + from efuse-address to pick up ABB characteristics. Set to 0 if + 'efuse-address' is not defined. + RBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to RBB mode if value at "efuse-address" + + efuse maps to RBB mask. Set to 0 to ignore this. + FBB enable efuse Mask: Optional if 'efuse-address' register is defined. + 'ABB mode' is force set to FBB mode if value at "efuse-address" + + efuse maps to FBB mask (valid only if RBB mask does not match) + Set to 0 to ignore this. + Vset value efuse Mask: Mandatory if ldo-address is set. Picks up from + efuse the value to set in 'ti,ldovbb-vset-mask' at ldo-address. + +Example #1: Simplest configuration (no efuse data, hard coded ABB table): +abb_x: regulator-abb-x { + compatible = "ti,abb-v1"; + regulator-name = "abb_x"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 1012500 0 0 0 0 0 /* Bypass */ + 1200000 3 0 0 0 0 /* RBB mandatory */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #2: Efuse bits contain ABB mode setting (no LDO override capability) +abb_y: regulator-abb-y { + compatible = "ti,abb-v2"; + regulator-name = "abb_y"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, <0x4A002268 0x8>; + reg-names = "base-address", "int-address", "efuse-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1012500 0 0 0x40000 0 0 /* RBB optional */ + 1200000 0 0x4 0 0x40000 0 /* FBB optional */ + 1320000 1 0 0 0 0 /* FBB mandatory */ + >; +}; + +Example #3: Efuse bits contain ABB mode setting and LDO override capability +abb_z: regulator-abb-z { + compatible = "ti,abb-v2"; + regulator-name = "abb_z"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>, + <0x4a002194 0x8>, <0x4ae0C314 0x4>; + reg-names = "base-address", "int-address", + "efuse-address", "ldo-address"; + ti,tranxdone-status-mask = <0x8000000>; + /* LDOVBBMM_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBMM_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + clocks = <&sysclk>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + ti,abb_info = < + /* uV ABB efuse rbb_m fbb_m vset_m */ + 975000 0 0 0 0 0 /* Bypass */ + 1200000 0 0x4 0 0x40000 0x1f00 /* FBB optional, vset */ + >; +}; diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt index 658749b90b97..75b0c1669504 100644 --- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt @@ -18,20 +18,20 @@ For twl6030 regulators/LDOs - "ti,twl6030-vdd1" for VDD1 SMPS - "ti,twl6030-vdd2" for VDD2 SMPS - "ti,twl6030-vdd3" for VDD3 SMPS -For twl6025 regulators/LDOs +For twl6032 regulators/LDOs - compatible: - - "ti,twl6025-ldo1" for LDO1 LDO - - "ti,twl6025-ldo2" for LDO2 LDO - - "ti,twl6025-ldo3" for LDO3 LDO - - "ti,twl6025-ldo4" for LDO4 LDO - - "ti,twl6025-ldo5" for LDO5 LDO - - "ti,twl6025-ldo6" for LDO6 LDO - - "ti,twl6025-ldo7" for LDO7 LDO - - "ti,twl6025-ldoln" for LDOLN LDO - - "ti,twl6025-ldousb" for LDOUSB LDO - - "ti,twl6025-smps3" for SMPS3 SMPS - - "ti,twl6025-smps4" for SMPS4 SMPS - - "ti,twl6025-vio" for VIO SMPS + - "ti,twl6032-ldo1" for LDO1 LDO + - "ti,twl6032-ldo2" for LDO2 LDO + - "ti,twl6032-ldo3" for LDO3 LDO + - "ti,twl6032-ldo4" for LDO4 LDO + - "ti,twl6032-ldo5" for LDO5 LDO + - "ti,twl6032-ldo6" for LDO6 LDO + - "ti,twl6032-ldo7" for LDO7 LDO + - "ti,twl6032-ldoln" for LDOLN LDO + - "ti,twl6032-ldousb" for LDOUSB LDO + - "ti,twl6032-smps3" for SMPS3 SMPS + - "ti,twl6032-smps4" for SMPS4 SMPS + - "ti,twl6032-vio" for VIO SMPS For twl4030 regulators/LDOs - compatible: - "ti,twl4030-vaux1" for VAUX1 LDO diff --git a/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt b/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt new file mode 100644 index 000000000000..0e72183f52bc --- /dev/null +++ b/Documentation/devicetree/bindings/serio/olpc,ap-sp.txt @@ -0,0 +1,13 @@ +OLPC AP-SP serio interface + +Required properties: +- compatible : "olpc,ap-sp" +- reg : base address and length of SoC's WTM registers +- interrupts : SP-AP interrupt + +Example: + ap-sp@d4290000 { + compatible = "olpc,ap-sp"; + reg = <0xd4290000 0x1000>; + interrupts = <40>; + } diff --git a/Documentation/devicetree/bindings/sound/adi,adau1701.txt b/Documentation/devicetree/bindings/sound/adi,adau1701.txt new file mode 100644 index 000000000000..547a49b56a62 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/adi,adau1701.txt @@ -0,0 +1,35 @@ +Analog Devices ADAU1701 + +Required properties: + + - compatible: Should contain "adi,adau1701" + - reg: The i2c address. Value depends on the state of ADDR0 + and ADDR1, as wired in hardware. + +Optional properties: + + - reset-gpio: A GPIO spec to define which pin is connected to the + chip's !RESET pin. If specified, the driver will + assert a hardware reset at probe time. + - adi,pll-mode-gpios: An array of two GPIO specs to describe the GPIOs + the ADAU's PLL config pins are connected to. + The state of the pins are set according to the + configured clock divider on ASoC side before the + firmware is loaded. + - adi,pin-config: An array of 12 numerical values selecting one of the + pin configurations as described in the datasheet, + table 53. Note that the value of this property has + to be prefixed with '/bits/ 8'. + +Examples: + + i2c_bus { + adau1701@34 { + compatible = "adi,adau1701"; + reg = <0x34>; + reset-gpio = <&gpio 23 0>; + adi,pll-mode-gpios = <&gpio 24 0 &gpio 25 0>; + adi,pin-config = /bits/ 8 <0x4 0x7 0x5 0x5 0x4 0x4 + 0x4 0x4 0x4 0x4 0x4 0x4>; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt new file mode 100644 index 000000000000..f49450a87890 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/imx-audio-wm8962.txt @@ -0,0 +1,46 @@ +Freescale i.MX audio complex with WM8962 codec + +Required properties: +- compatible : "fsl,imx-audio-wm8962" +- model : The user-visible name of this sound complex +- ssi-controller : The phandle of the i.MX SSI controller +- audio-codec : The phandle of the WM8962 audio codec +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names could be power + supplies, WM8962 pins, and the jacks on the board: + + Power supplies: + * Mic Bias + + Board connectors: + * Mic Jack + * Headphone Jack + * Ext Spk + +- mux-int-port : The internal port of the i.MX audio muxer (AUDMUX) +- mux-ext-port : The external port of the i.MX audio muxer + +Note: The AUDMUX port numbering should start at 1, which is consistent with +hardware manual. + +Example: + +sound { + compatible = "fsl,imx6q-sabresd-wm8962", + "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "MICBIAS", "AMIC", + "IN3R", "MICBIAS", + "DMIC", "MICBIAS", + "DMICDAT", "DMIC"; + mux-int-port = <2>; + mux-ext-port = <3>; +}; diff --git a/Documentation/devicetree/bindings/sound/mxs-saif.txt b/Documentation/devicetree/bindings/sound/mxs-saif.txt index c37ba6143d9b..7ba07a118e37 100644 --- a/Documentation/devicetree/bindings/sound/mxs-saif.txt +++ b/Documentation/devicetree/bindings/sound/mxs-saif.txt @@ -3,8 +3,11 @@ Required properties: - compatible: Should be "fsl,<chip>-saif" - reg: Should contain registers location and length -- interrupts: Should contain ERROR and DMA interrupts -- fsl,saif-dma-channel: APBX DMA channel for the SAIF +- interrupts: Should contain ERROR interrupt number +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and SAIF DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: Must be "rx-tx". Optional properties: - fsl,saif-master: phandle to the master SAIF. It's only required for @@ -23,14 +26,16 @@ aliases { saif0: saif@80042000 { compatible = "fsl,imx28-saif"; reg = <0x80042000 2000>; - interrupts = <59 80>; - fsl,saif-dma-channel = <4>; + interrupts = <59>; + dmas = <&dma_apbx 4>; + dma-names = "rx-tx"; }; saif1: saif@80046000 { compatible = "fsl,imx28-saif"; reg = <0x80046000 2000>; - interrupts = <58 81>; - fsl,saif-dma-channel = <5>; + interrupts = <58>; + dmas = <&dma_apbx 5>; + dma-names = "rx-tx"; fsl,saif-master = <&saif0>; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt new file mode 100644 index 000000000000..d130818700b2 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-rt5640.txt @@ -0,0 +1,71 @@ +NVIDIA Tegra audio complex, with RT5640 CODEC + +Required properties: +- compatible : "nvidia,tegra-audio-rt5640" +- clocks : Must contain an entry for each entry in clock-names. +- clock-names : Must include the following entries: + "pll_a" (The Tegra clock of that name), + "pll_a_out0" (The Tegra clock of that name), + "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk) +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the RT5640's pins, and the jacks on the board: + + RT5640 pins: + + * DMIC1 + * DMIC2 + * MICBIAS1 + * IN1P + * IN1R + * IN2P + * IN2R + * HPOL + * HPOR + * LOUTL + * LOUTR + * MONOP + * MONON + * SPOLP + * SPOLN + * SPORP + * SPORN + + Board connectors: + + * Headphones + * Speakers + +- nvidia,i2s-controller : The phandle of the Tegra I2S controller that's + connected to the CODEC. +- nvidia,audio-codec : The phandle of the RT5640 audio codec. This binding + assumes that AIF1 on the CODEC is connected to Tegra. + +Optional properties: +- nvidia,hp-det-gpios : The GPIO that detects headphones are plugged in + +Example: + +sound { + compatible = "nvidia,tegra-audio-rt5640-dalmore", + "nvidia,tegra-audio-rt5640"; + nvidia,model = "NVIDIA Tegra Dalmore"; + + nvidia,audio-routing = + "Headphones", "HPOR", + "Headphones", "HPOL", + "Speakers", "SPORP", + "Speakers", "SPORN", + "Speakers", "SPOLP", + "Speakers", "SPOLN"; + + nvidia,i2s-controller = <&tegra_i2s1>; + nvidia,audio-codec = <&rt5640>; + + nvidia,hp-det-gpios = <&gpio 143 0>; /* GPIO PR7 */ + + clocks = <&tegra_car 216>, <&tegra_car 217>, <&tegra_car 120>; + clock-names = "pll_a", "pll_a_out0", "mclk"; +}; diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt new file mode 100644 index 000000000000..005bcb24d72d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt5640.txt @@ -0,0 +1,30 @@ +RT5640 audio CODEC + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt5640". + +- reg : The I2C address of the device. + +- interrupts : The CODEC's interrupt output. + +Optional properties: + +- realtek,in1-differential +- realtek,in2-differential + Boolean. Indicate MIC1/2 input are differential, rather than single-ended. + +- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin. + +Example: + +rt5640 { + compatible = "realtek,rt5640"; + reg = <0x1c>; + interrupt-parent = <&gpio>; + interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>; + realtek,ldo1-en-gpios = + <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/sound/sgtl5000.txt b/Documentation/devicetree/bindings/sound/sgtl5000.txt index 9cc44449508d..955df60a118c 100644 --- a/Documentation/devicetree/bindings/sound/sgtl5000.txt +++ b/Documentation/devicetree/bindings/sound/sgtl5000.txt @@ -5,9 +5,12 @@ Required properties: - reg : the I2C address of the device +- clocks : the clock provider of SYS_MCLK + Example: codec: sgtl5000@0a { compatible = "fsl,sgtl5000"; reg = <0x0a>; + clocks = <&clks 150>; }; diff --git a/Documentation/devicetree/bindings/sound/spdif-receiver.txt b/Documentation/devicetree/bindings/sound/spdif-receiver.txt new file mode 100644 index 000000000000..80f807bf8a1d --- /dev/null +++ b/Documentation/devicetree/bindings/sound/spdif-receiver.txt @@ -0,0 +1,10 @@ +Device-Tree bindings for dummy spdif receiver + +Required properties: + - compatible: should be "linux,spdif-dir". + +Example node: + + codec: spdif-receiver { + compatible = "linux,spdif-dir"; + }; diff --git a/Documentation/devicetree/bindings/sound/spdif-transmitter.txt b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt new file mode 100644 index 000000000000..55a85841dd85 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/spdif-transmitter.txt @@ -0,0 +1,10 @@ +Device-Tree bindings for dummy spdif transmitter + +Required properties: + - compatible: should be "linux,spdif-dit". + +Example node: + + codec: spdif-transmitter { + compatible = "linux,spdif-dit"; + }; diff --git a/Documentation/devicetree/bindings/sound/ssm2518.txt b/Documentation/devicetree/bindings/sound/ssm2518.txt new file mode 100644 index 000000000000..59381a778c79 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ssm2518.txt @@ -0,0 +1,20 @@ +SSM2518 audio amplifier + +This device supports I2C only. + +Required properties: + - compatible : Must be "adi,ssm2518" + - reg : the I2C address of the device. This will either be 0x34 (ADDR pin low) + or 0x35 (ADDR pin high) + +Optional properties: + - gpios : GPIO connected to the nSD pin. If the property is not present it is + assumed that the nSD pin is hardwired to always on. + +Example: + + ssm2518: ssm2518@34 { + compatible = "adi,ssm2518"; + reg = <0x34>; + gpios = <&gpio 5 0>; + }; diff --git a/Documentation/devicetree/bindings/sound/ti,tas5086.txt b/Documentation/devicetree/bindings/sound/ti,tas5086.txt index 8ea4f5b4818d..d2866a0d6a26 100644 --- a/Documentation/devicetree/bindings/sound/ti,tas5086.txt +++ b/Documentation/devicetree/bindings/sound/ti,tas5086.txt @@ -20,6 +20,17 @@ Optional properties: When not specified, the hardware default of 1300ms is retained. + - ti,mid-z-channel-X: Boolean properties, X being a number from 1 to 6. + If given, channel X will start with the Mid-Z start + sequence, otherwise the default Low-Z scheme is used. + + The correct configuration depends on how the power + stages connected to the PWM output pins work. Not all + power stages are compatible to Mid-Z - please refer + to the datasheets for more details. + + Most systems should not set any of these properties. + Examples: i2c_bus { diff --git a/Documentation/devicetree/bindings/sound/wm8962.txt b/Documentation/devicetree/bindings/sound/wm8962.txt index dceb3b1c2bb7..7f82b59ec8f9 100644 --- a/Documentation/devicetree/bindings/sound/wm8962.txt +++ b/Documentation/devicetree/bindings/sound/wm8962.txt @@ -8,9 +8,32 @@ Required properties: - reg : the I2C address of the device. +Optional properties: + - spk-mono: This is a boolean property. If present, the SPK_MONO bit + of R51 (Class D Control 2) gets set, indicating that the speaker is + in mono mode. + + - mic-cfg : Default register value for R48 (Additional Control 4). + If absent, the default should be the register default. + + - gpio-cfg : A list of GPIO configuration register values. The list must + be 6 entries long. If absent, no configuration of these registers is + performed. And note that only the value within [0x0, 0xffff] is valid. + Any other value is regarded as setting the GPIO register by its reset + value 0x0. + Example: codec: wm8962@1a { compatible = "wlf,wm8962"; reg = <0x1a>; + + gpio-cfg = < + 0x0000 /* 0:Default */ + 0x0000 /* 1:Default */ + 0x0013 /* 2:FN_DMICCLK */ + 0x0000 /* 3:Default */ + 0x8014 /* 4:FN_DMICCDAT */ + 0x0000 /* 5:Default */ + >; }; diff --git a/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt index 8bf89c643640..f11f295c8450 100644 --- a/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt +++ b/Documentation/devicetree/bindings/spi/brcm,bcm2835-spi.txt @@ -2,7 +2,7 @@ Broadcom BCM2835 SPI0 controller The BCM2835 contains two forms of SPI master controller, one known simply as SPI0, and the other known as the "Universal SPI Master"; part of the -auxilliary block. This binding applies to the SPI0 controller. +auxiliary block. This binding applies to the SPI0 controller. Required properties: - compatible: Should be "brcm,bcm2835-spi". diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt index 938809c6829b..4c85c4c69584 100644 --- a/Documentation/devicetree/bindings/spi/omap-spi.txt +++ b/Documentation/devicetree/bindings/spi/omap-spi.txt @@ -10,7 +10,18 @@ Required properties: input. The default is D0 as input and D1 as output. -Example: +Optional properties: +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required for each chip select. +- dma-names: List of DMA request names. These strings correspond + 1:1 with the DMA specifiers listed in dmas. The string naming + is to be "rxN" and "txN" for RX and TX requests, + respectively, where N equals the chip select number. + +Examples: + +[hwmod populated DMA resources] mcspi1: mcspi@1 { #address-cells = <1>; @@ -20,3 +31,17 @@ mcspi1: mcspi@1 { ti,spi-num-cs = <4>; }; +[generic DMA request binding] + +mcspi1: mcspi@1 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,omap4-mcspi"; + ti,hwmods = "mcspi1"; + ti,spi-num-cs = <2>; + dmas = <&edma 42 + &edma 43 + &edma 44 + &edma 45>; + dma-names = "tx0", "rx0", "tx1", "rx1"; +}; diff --git a/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt b/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt new file mode 100644 index 000000000000..0c9222d27fae --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/ti_soc_thermal.txt @@ -0,0 +1,74 @@ +* Texas Instrument OMAP SCM bandgap bindings + +In the System Control Module, OMAP supplies a voltage reference +and a temperature sensor feature that are gathered in the band +gap voltage and temperature sensor (VBGAPTS) module. The band +gap provides current and voltage reference for its internal +circuits and other analog IP blocks. The analog-to-digital +converter (ADC) produces an output value that is proportional +to the silicon temperature. + +Required properties: +- compatible : Should be: + - "ti,omap4430-bandgap" : for OMAP4430 bandgap + - "ti,omap4460-bandgap" : for OMAP4460 bandgap + - "ti,omap4470-bandgap" : for OMAP4470 bandgap + - "ti,omap5430-bandgap" : for OMAP5430 bandgap +- interrupts : this entry should indicate which interrupt line +the talert signal is routed to; +Specific: +- gpios : this entry should be used to inform which GPIO +line the tshut signal is routed to. The informed GPIO will +be treated as an IRQ; +- regs : this entry must also be specified and it is specific +to each bandgap version, because the mapping may change from +soc to soc, apart of depending on available features. + +Example: +OMAP4430: +bandgap { + reg = <0x4a002260 0x4 0x4a00232C 0x4>; + compatible = "ti,omap4430-bandgap"; +}; + +OMAP4460: +bandgap { + reg = <0x4a002260 0x4 + 0x4a00232C 0x4 + 0x4a002378 0x18>; + compatible = "ti,omap4460-bandgap"; + interrupts = <0 126 4>; /* talert */ + gpios = <&gpio3 22 0>; /* tshut */ +}; + +OMAP4470: +bandgap { + reg = <0x4a002260 0x4 + 0x4a00232C 0x4 + 0x4a002378 0x18>; + compatible = "ti,omap4470-bandgap"; + interrupts = <0 126 4>; /* talert */ + gpios = <&gpio3 22 0>; /* tshut */ +}; + +OMAP5430: +bandgap { + reg = <0x4a0021e0 0xc + 0x4a00232c 0xc + 0x4a002380 0x2c + 0x4a0023C0 0x3c>; + compatible = "ti,omap5430-bandgap"; + interrupts = <0 126 4>; /* talert */ +}; + +DRA752: +bandgap { + reg = <0x4a0021e0 0xc + 0x4a00232c 0xc + 0x4a002380 0x2c + 0x4a0023C0 0x3c + 0x4a002564 0x8 + 0x4a002574 0x50>; + compatible = "ti,dra752-bandgap"; + interrupts = <0 126 4>; /* talert */ +}; diff --git a/Documentation/devicetree/bindings/timer/lsi,zevio-timer.txt b/Documentation/devicetree/bindings/timer/lsi,zevio-timer.txt new file mode 100644 index 000000000000..b2d07ad90e9a --- /dev/null +++ b/Documentation/devicetree/bindings/timer/lsi,zevio-timer.txt @@ -0,0 +1,33 @@ +TI-NSPIRE timer + +Required properties: + +- compatible : should be "lsi,zevio-timer". +- reg : The physical base address and size of the timer (always first). +- clocks: phandle to the source clock. + +Optional properties: + +- interrupts : The interrupt number of the first timer. +- reg : The interrupt acknowledgement registers + (always after timer base address) + +If any of the optional properties are not given, the timer is added as a +clock-source only. + +Example: + +timer { + compatible = "lsi,zevio-timer"; + reg = <0x900D0000 0x1000>, <0x900A0020 0x8>; + interrupts = <19>; + clocks = <&timer_clk>; +}; + +Example (no clock-events): + +timer { + compatible = "lsi,zevio-timer"; + reg = <0x900D0000 0x1000>; + clocks = <&timer_clk>; +}; diff --git a/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt b/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt index cb47bfbcaeea..b5a86d20ee36 100644 --- a/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt +++ b/Documentation/devicetree/bindings/timer/samsung,exynos4210-mct.txt @@ -44,7 +44,7 @@ Example 1: In this example, the system uses only the first global timer }; Example 2: In this example, the MCT global and local timer interrupts are - connected to two seperate interrupt controllers. Hence, an + connected to two separate interrupt controllers. Hence, an interrupt-map is created to map the interrupts to the respective interrupt controllers. diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt new file mode 100644 index 000000000000..20468b2a7516 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -0,0 +1,16 @@ +* Universal Flash Storage (UFS) Host Controller + +UFSHC nodes are defined to describe on-chip UFS host controllers. +Each UFS controller instance should have its own node. + +Required properties: +- compatible : compatible list, contains "jedec,ufs-1.1" +- interrupts : <interrupt mapping for UFS host controller IRQ> +- reg : <registers mapping> + +Example: + ufshc@0xfc598000 { + compatible = "jedec,ufs-1.1"; + reg = <0xfc598000 0x800>; + interrupts = <0 28 0>; + }; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt index ea840f7f9258..dc9dc8c87f15 100644 --- a/Documentation/devicetree/bindings/usb/am33xx-usb.txt +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -12,7 +12,7 @@ AM33XX MUSB GLUE represents PERIPHERAL. - port1-mode : Should be "1" to represent HOST. "3" signifies OTG and "2" represents PERIPHERAL. - - power : Should be "250". This signifies the controller can supply upto + - power : Should be "250". This signifies the controller can supply up to 500mA when operating in host mode. Example: diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt index d4769f343d6c..57e71f6817d0 100644 --- a/Documentation/devicetree/bindings/usb/omap-usb.txt +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -16,7 +16,7 @@ OMAP MUSB GLUE specifying ULPI and UTMI respectively. - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" represents PERIPHERAL. - - power : Should be "50". This signifies the controller can supply upto + - power : Should be "50". This signifies the controller can supply up to 100mA when operating in host mode. - usb-phy : the phandle for the PHY device diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt index 36b9aede3f40..0aee0ad3f035 100644 --- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -8,7 +8,7 @@ TWL6030 USB COMPARATOR usb interrupt number that raises VBUS interrupts when the controller has to act as device - usb-supply : phandle to the regulator device tree node. It should be vusb - if it is twl6030 or ldousb if it is twl6025 subclass. + if it is twl6030 or ldousb if it is twl6032 subclass. twl6030-usb { compatible = "ti,twl6030-usb"; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index db0457d61682..d5a79caec147 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -18,6 +18,7 @@ chrp Common Hardware Reference Platform cirrus Cirrus Logic, Inc. cortina Cortina Systems, Inc. dallas Maxim Integrated Products (formerly Dallas Semiconductor) +davicom DAVICOM Semiconductor, Inc. denx Denx Software Engineering emmicro EM Microelectronic epson Seiko Epson Corp. @@ -58,6 +59,7 @@ snps Synopsys, Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson +toumaz Toumaz ti Texas Instruments toshiba Toshiba Corporation v3 V3 Semiconductor diff --git a/Documentation/devicetree/bindings/video/display-timing.txt b/Documentation/devicetree/bindings/video/display-timing.txt index 150038552bc3..e1d4a0b59612 100644 --- a/Documentation/devicetree/bindings/video/display-timing.txt +++ b/Documentation/devicetree/bindings/video/display-timing.txt @@ -34,6 +34,7 @@ optional properties: - ignored = ignored - interlaced (bool): boolean to enable interlaced mode - doublescan (bool): boolean to enable doublescan mode + - doubleclk (bool): boolean to enable doubleclock mode All the optional properties that are not bool follow the following logic: <1>: high active diff --git a/Documentation/devicetree/bindings/video/exynos_hdmi.txt b/Documentation/devicetree/bindings/video/exynos_hdmi.txt index 589edee37394..323983be3c30 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmi.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmi.txt @@ -1,22 +1,23 @@ Device-Tree bindings for drm hdmi driver Required properties: -- compatible: value should be "samsung,exynos5-hdmi". +- compatible: value should be one among the following: + 1) "samsung,exynos5-hdmi" <DEPRECATED> + 2) "samsung,exynos4210-hdmi" + 3) "samsung,exynos4212-hdmi" - reg: physical base address of the hdmi and length of memory mapped region. - interrupts: interrupt number to the cpu. - hpd-gpio: following information about the hotplug gpio pin. a) phandle of the gpio controller node. b) pin number within the gpio controller. - c) pin function mode. - d) optional flags and pull up/down. - e) drive strength. + c) optional flags and pull up/down. Example: hdmi { - compatible = "samsung,exynos5-hdmi"; + compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x100000>; interrupts = <0 95 0>; - hpd-gpio = <&gpx3 7 0xf 1 3>; + hpd-gpio = <&gpx3 7 1>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt index fa166d945809..41eee971562b 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiddc.txt @@ -1,12 +1,15 @@ Device-Tree bindings for hdmiddc driver Required properties: -- compatible: value should be "samsung,exynos5-hdmiddc". +- compatible: value should be one of the following + 1) "samsung,exynos5-hdmiddc" <DEPRECATED> + 2) "samsung,exynos4210-hdmiddc" + - reg: I2C address of the hdmiddc device. Example: hdmiddc { - compatible = "samsung,exynos5-hdmiddc"; + compatible = "samsung,exynos4210-hdmiddc"; reg = <0x50>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt index 858f4f9b902f..162f641f7639 100644 --- a/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt +++ b/Documentation/devicetree/bindings/video/exynos_hdmiphy.txt @@ -1,12 +1,15 @@ Device-Tree bindings for hdmiphy driver Required properties: -- compatible: value should be "samsung,exynos5-hdmiphy". +- compatible: value should be one of the following: + 1) "samsung,exynos5-hdmiphy" <DEPRECATED> + 2) "samsung,exynos4210-hdmiphy". + 3) "samsung,exynos4212-hdmiphy". - reg: I2C address of the hdmiphy device. Example: hdmiphy { - compatible = "samsung,exynos5-hdmiphy"; + compatible = "samsung,exynos4210-hdmiphy"; reg = <0x38>; }; diff --git a/Documentation/devicetree/bindings/video/exynos_mixer.txt b/Documentation/devicetree/bindings/video/exynos_mixer.txt index 9b2ea0343566..3334b0a8e343 100644 --- a/Documentation/devicetree/bindings/video/exynos_mixer.txt +++ b/Documentation/devicetree/bindings/video/exynos_mixer.txt @@ -1,7 +1,12 @@ Device-Tree bindings for mixer driver Required properties: -- compatible: value should be "samsung,exynos5-mixer". +- compatible: value should be one of the following: + 1) "samsung,exynos5-mixer" <DEPRECATED> + 2) "samsung,exynos4210-mixer" + 3) "samsung,exynos5250-mixer" + 4) "samsung,exynos5420-mixer" + - reg: physical base address of the mixer and length of memory mapped region. - interrupts: interrupt number to the cpu. @@ -9,7 +14,7 @@ Required properties: Example: mixer { - compatible = "samsung,exynos5-mixer"; + compatible = "samsung,exynos5250-mixer"; reg = <0x14450000 0x10000>; interrupts = <0 94 0>; }; diff --git a/Documentation/devicetree/bindings/video/fsl,imx-fb.txt b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt new file mode 100644 index 000000000000..46da08db186a --- /dev/null +++ b/Documentation/devicetree/bindings/video/fsl,imx-fb.txt @@ -0,0 +1,51 @@ +Freescale imx21 Framebuffer + +This framebuffer driver supports devices imx1, imx21, imx25, and imx27. + +Required properties: +- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21 +- reg : Should contain 1 register ranges(address and length) +- interrupts : One interrupt of the fb dev + +Required nodes: +- display: Phandle to a display node as described in + Documentation/devicetree/bindings/video/display-timing.txt + Additional, the display node has to define properties: + - bits-per-pixel: Bits per pixel + - fsl,pcr: LCDC PCR value + +Optional properties: +- fsl,dmacr: DMA Control Register value. This is optional. By default, the + register is not modified as recommended by the datasheet. +- fsl,lscr1: LCDC Sharp Configuration Register value. + +Example: + + imxfb: fb@10021000 { + compatible = "fsl,imx21-fb"; + interrupts = <61>; + reg = <0x10021000 0x1000>; + display = <&display0>; + }; + + ... + + display0: display0 { + model = "Primeview-PD050VL1"; + native-mode = <&timing_disp0>; + bits-per-pixel = <16>; + fsl,pcr = <0xf0c88080>; /* non-standard but required */ + display-timings { + timing_disp0: 640x480 { + hactive = <640>; + vactive = <480>; + hback-porch = <112>; + hfront-porch = <36>; + hsync-len = <32>; + vback-porch = <33>; + vfront-porch = <33>; + vsync-len = <2>; + clock-frequency = <25000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/video/ssd1307fb.txt b/Documentation/devicetree/bindings/video/ssd1307fb.txt index 3d0060cff062..7a125427ff4b 100644 --- a/Documentation/devicetree/bindings/video/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/video/ssd1307fb.txt @@ -1,13 +1,17 @@ * Solomon SSD1307 Framebuffer Driver Required properties: - - compatible: Should be "solomon,ssd1307fb-<bus>". The only supported bus for - now is i2c. + - compatible: Should be "solomon,<chip>fb-<bus>". The only supported bus for + now is i2c, and the supported chips are ssd1306 and ssd1307. - reg: Should contain address of the controller on the I2C bus. Most likely 0x3c or 0x3d - pwm: Should contain the pwm to use according to the OF device tree PWM - specification [0] + specification [0]. Only required for the ssd1307. - reset-gpios: Should contain the GPIO used to reset the OLED display + - solomon,height: Height in pixel of the screen driven by the controller + - solomon,width: Width in pixel of the screen driven by the controller + - solomon,page-offset: Offset of pages (band of 8 pixels) that the screen is + mapped to. Optional properties: - reset-active-low: Is the reset gpio is active on physical low? |