diff options
Diffstat (limited to 'Documentation/devicetree')
13 files changed, 203 insertions, 15 deletions
diff --git a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt index 9f1d750d76de..61bca509d7b9 100644 --- a/Documentation/devicetree/bindings/dma/rcar-audmapp.txt +++ b/Documentation/devicetree/bindings/dma/rcar-audmapp.txt @@ -16,9 +16,9 @@ Example: * DMA client Required properties: -- dmas: a list of <[DMA multiplexer phandle] [SRS/DRS value]> pairs, - where SRS/DRS values are fixed handles, specified in the SoC - manual as the value that would be written into the PDMACHCR. +- dmas: a list of <[DMA multiplexer phandle] [SRS << 8 | DRS]> pairs. + where SRS/DRS are specified in the SoC manual. + It will be written into PDMACHCR as high 16-bit parts. - dma-names: a list of DMA channel names, one per "dmas" entry Example: diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt index baef432e8369..0ac23f2ed104 100644 --- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -15,6 +15,17 @@ Optional properties for main touchpad device: keycode generated by each GPIO. Linux keycodes are defined in <dt-bindings/input/input.h>. +- linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages + on GPIO bit changes. An array of up to 8 entries can be provided + indicating the Linux keycode mapped to each bit of the status byte, + starting at the LSB. Linux keycodes are defined in + <dt-bindings/input/input.h>. + + Note: the numbering of the GPIOs and the bit they start at varies between + maXTouch devices. You must either refer to the documentation, or + experiment to determine which bit corresponds to which input. Use + KEY_RESERVED for unused padding values. + Example: touch@4b { diff --git a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt index 1486497a24c1..ce6a1a072028 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/interrupts.txt @@ -4,11 +4,13 @@ Specifying interrupt information for devices 1) Interrupt client nodes ------------------------- -Nodes that describe devices which generate interrupts must contain an either an -"interrupts" property or an "interrupts-extended" property. These properties -contain a list of interrupt specifiers, one per output interrupt. The format of -the interrupt specifier is determined by the interrupt controller to which the -interrupts are routed; see section 2 below for details. +Nodes that describe devices which generate interrupts must contain an +"interrupts" property, an "interrupts-extended" property, or both. If both are +present, the latter should take precedence; the former may be provided simply +for compatibility with software that does not recognize the latter. These +properties contain a list of interrupt specifiers, one per output interrupt. The +format of the interrupt specifier is determined by the interrupt controller to +which the interrupts are routed; see section 2 below for details. Example: interrupt-parent = <&intc1>; diff --git a/Documentation/devicetree/bindings/mfd/tc3589x.txt b/Documentation/devicetree/bindings/mfd/tc3589x.txt new file mode 100644 index 000000000000..6fcedba46ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tc3589x.txt @@ -0,0 +1,107 @@ +* Toshiba TC3589x multi-purpose expander + +The Toshiba TC3589x series are I2C-based MFD devices which may expose the +following built-in devices: gpio, keypad, rotator (vibrator), PWM (for +e.g. LEDs or vibrators) The included models are: + +- TC35890 +- TC35892 +- TC35893 +- TC35894 +- TC35895 +- TC35896 + +Required properties: + - compatible : must be "toshiba,tc35890", "toshiba,tc35892", "toshiba,tc35893", + "toshiba,tc35894", "toshiba,tc35895" or "toshiba,tc35896" + - reg : I2C address of the device + - interrupt-parent : specifies which IRQ controller we're connected to + - interrupts : the interrupt on the parent the controller is connected to + - interrupt-controller : marks the device node as an interrupt controller + - #interrupt-cells : should be <1>, the first cell is the IRQ offset on this + TC3589x interrupt controller. + +Optional nodes: + +- GPIO + This GPIO module inside the TC3589x has 24 (TC35890, TC35892) or 20 + (other models) GPIO lines. + - compatible : must be "toshiba,tc3589x-gpio" + - interrupts : interrupt on the parent, which must be the tc3589x MFD device + - interrupt-controller : marks the device node as an interrupt controller + - #interrupt-cells : should be <2>, the first cell is the IRQ offset on this + TC3589x GPIO interrupt controller, the second cell is the interrupt flags + in accordance with <dt-bindings/interrupt-controller/irq.h>. The following + flags are valid: + - IRQ_TYPE_LEVEL_LOW + - IRQ_TYPE_LEVEL_HIGH + - IRQ_TYPE_EDGE_RISING + - IRQ_TYPE_EDGE_FALLING + - IRQ_TYPE_EDGE_BOTH + - gpio-controller : marks the device node as a GPIO controller + - #gpio-cells : should be <2>, the first cell is the GPIO offset on this + GPIO controller, the second cell is the flags. + +- Keypad + This keypad is the same on all variants, supporting up to 96 different + keys. The linux-specific properties are modeled on those already existing + in other input drivers. + - compatible : must be "toshiba,tc3589x-keypad" + - debounce-delay-ms : debounce interval in milliseconds + - keypad,num-rows : number of rows in the matrix, see + bindings/input/matrix-keymap.txt + - keypad,num-columns : number of columns in the matrix, see + bindings/input/matrix-keymap.txt + - linux,keymap: the definition can be found in + bindings/input/matrix-keymap.txt + - linux,no-autorepeat: do no enable autorepeat feature. + - linux,wakeup: use any event on keypad as wakeup event. + +Example: + +tc35893@44 { + compatible = "toshiba,tc35893"; + reg = <0x44>; + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <1>; + + tc3589x_gpio { + compatible = "toshiba,tc3589x-gpio"; + interrupts = <0>; + + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + tc3589x_keypad { + compatible = "toshiba,tc3589x-keypad"; + interrupts = <6>; + debounce-delay-ms = <4>; + keypad,num-columns = <8>; + keypad,num-rows = <8>; + linux,no-autorepeat; + linux,wakeup; + linux,keymap = <0x0301006b + 0x04010066 + 0x06040072 + 0x040200d7 + 0x0303006a + 0x0205000e + 0x0607008b + 0x0500001c + 0x0403000b + 0x03040034 + 0x05020067 + 0x0305006c + 0x040500e7 + 0x0005009e + 0x06020073 + 0x01030039 + 0x07060069 + 0x050500d9>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt index 65f4f7c43136..ee654e95d8ad 100644 --- a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt +++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt @@ -22,7 +22,7 @@ Optional properties: width of 8 is assumed. - ti,nand-ecc-opt: A string setting the ECC layout to use. One of: - "sw" <deprecated> use "ham1" instead + "sw" 1-bit Hamming ecc code via software "hw" <deprecated> use "ham1" instead "hw-romcode" <deprecated> use "ham1" instead "ham1" 1-bit Hamming ecc code diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 9b03c57563a4..e45ac3f926b1 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -39,6 +39,10 @@ Optional properties: further clocks may be specified in derived bindings. - clock-names: One name for each entry in the clocks property, the first one should be "stmmaceth". +- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is + available this clock is used for programming the Timestamp Addend Register. + If not passed then the system clock will be used and this is fine on some + platforms. Examples: diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index d0d15ee42834..ed0d9b9fff2b 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -2,6 +2,10 @@ Required properties: - compatible: should contain "snps,dw-pcie" to identify the core. +- reg: Should contain the configuration address space. +- reg-names: Must be "config" for the PCIe configuration space. + (The old way of getting the configuration address space from "ranges" + is deprecated and should be avoided.) - #address-cells: set to <3> - #size-cells: set to <2> - device_type: set to "pci" diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt new file mode 100644 index 000000000000..3d217911b313 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -0,0 +1,59 @@ +TI PCI Controllers + +PCIe Designware Controller + - compatible: Should be "ti,dra7-pcie"" + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI specific registers + The second entry must be "rc-dbics" for the designware pcie + registers + The third entry must be "config" for the PCIe configuration space + - phys : list of PHY specifiers (used by generic PHY framework) + - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. + - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", + where <X> is the instance number of the pcie from the HW spec. + - interrupts : Two interrupt entries must be specified. The first one is for + main interrupt line and the second for MSI interrupt line. + - #address-cells, + #size-cells, + #interrupt-cells, + device_type, + ranges, + num-lanes, + interrupt-map-mask, + interrupt-map : as specified in ../designware-pcie.txt + +Example: +axi { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0x51000000 0x51000000 0x3000 + 0x0 0x20000000 0x10000000>; + pcie@51000000 { + compatible = "ti,dra7-pcie"; + reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; + reg-names = "rc_dbics", "ti_conf", "config"; + interrupts = <0 232 0x4>, <0 233 0x4>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x03000 0 0x00010000 + 0x82000000 0 0x20013000 0x13000 0 0xffed000>; + #interrupt-cells = <1>; + num-lanes = <1>; + ti,hwmods = "pcie1"; + phys = <&pcie1_phy>; + phy-names = "pcie-phy0"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt index 0211c6d8a522..92fae82f35f2 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,apq8064-pinctrl.txt @@ -62,7 +62,7 @@ Example: #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - interrupts = <0 32 0x4>; + interrupts = <0 16 0x4>; pinctrl-names = "default"; pinctrl-0 = <&gsbi5_uart_default>; diff --git a/Documentation/devicetree/bindings/regulator/tps65090.txt b/Documentation/devicetree/bindings/regulator/tps65090.txt index 340980239ea9..ca69f5e3040c 100644 --- a/Documentation/devicetree/bindings/regulator/tps65090.txt +++ b/Documentation/devicetree/bindings/regulator/tps65090.txt @@ -45,8 +45,8 @@ Example: infet5-supply = <&some_reg>; infet6-supply = <&some_reg>; infet7-supply = <&some_reg>; - vsys_l1-supply = <&some_reg>; - vsys_l2-supply = <&some_reg>; + vsys-l1-supply = <&some_reg>; + vsys-l2-supply = <&some_reg>; regulators { dcdc1 { diff --git a/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt b/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt index 46f344965313..4eb7997674a0 100644 --- a/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt +++ b/Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt @@ -1,7 +1,7 @@ ADI AXI-SPDIF controller Required properties: - - compatible : Must be "adi,axi-spdif-1.00.a" + - compatible : Must be "adi,axi-spdif-tx-1.00.a" - reg : Must contain SPDIF core's registers location and length - clocks : Pairs of phandle and specifier referencing the controller's clocks. The controller expects two clocks, the clock used for the AXI interface and diff --git a/Documentation/devicetree/bindings/usb/mxs-phy.txt b/Documentation/devicetree/bindings/usb/mxs-phy.txt index cef181a9d8bd..96681c93b86d 100644 --- a/Documentation/devicetree/bindings/usb/mxs-phy.txt +++ b/Documentation/devicetree/bindings/usb/mxs-phy.txt @@ -5,6 +5,7 @@ Required properties: * "fsl,imx23-usbphy" for imx23 and imx28 * "fsl,imx6q-usbphy" for imx6dq and imx6dl * "fsl,imx6sl-usbphy" for imx6sl + * "fsl,imx6sx-usbphy" for imx6sx "fsl,imx23-usbphy" is still a fallback for other strings - reg: Should contain registers location and length - interrupts: Should contain phy interrupt diff --git a/Documentation/devicetree/bindings/video/analog-tv-connector.txt b/Documentation/devicetree/bindings/video/analog-tv-connector.txt index 0218fcdc1299..0c0970c210ab 100644 --- a/Documentation/devicetree/bindings/video/analog-tv-connector.txt +++ b/Documentation/devicetree/bindings/video/analog-tv-connector.txt @@ -2,7 +2,7 @@ Analog TV Connector =================== Required properties: -- compatible: "composite-connector" or "svideo-connector" +- compatible: "composite-video-connector" or "svideo-connector" Optional properties: - label: a symbolic name for the connector @@ -14,7 +14,7 @@ Example ------- tv: connector { - compatible = "composite-connector"; + compatible = "composite-video-connector"; label = "tv"; port { |