diff options
Diffstat (limited to 'Documentation/devicetree')
| -rw-r--r-- | Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml | 480 |
1 files changed, 480 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml new file mode 100644 index 000000000000..d4922f9f0376 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/adi,ltc2983.yaml @@ -0,0 +1,480 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/temperature/adi,ltc2983.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2983 Multi-sensor Temperature system + +maintainers: + - Nuno Sá <nuno.sa@analog.com> + +description: | + Analog Devices LTC2983 Multi-Sensor Digital Temperature Measurement System + https://www.analog.com/media/en/technical-documentation/data-sheets/2983fc.pdf + +properties: + compatible: + enum: + - adi,ltc2983 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + adi,mux-delay-config-us: + description: + The LTC2983 performs 2 or 3 internal conversion cycles per temperature + result. Each conversion cycle is performed with different excitation and + input multiplexer configurations. Prior to each conversion, these + excitation circuits and input switch configurations are changed and an + internal 1ms delay ensures settling prior to the conversion cycle in most + cases. An extra delay can be configured using this property. The value is + rounded to nearest 100us. + maximum: 255 + + adi,filter-notch-freq: + description: + Set's the default setting of the digital filter. The default is + simultaneous 50/60Hz rejection. + 0 - 50/60Hz rejection + 1 - 60Hz rejection + 2 - 50Hz rejection + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + maximum: 2 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "@([1-9]|1[0-9]|20)$": + type: object + + properties: + reg: + description: + The channel number. It can be connected to one of the 20 channels of + the device. + minimum: 1 + maximum: 20 + + adi,sensor-type: + description: Identifies the type of sensor connected to the device. + $ref: /schemas/types.yaml#/definitions/uint32 + + required: + - reg + - adi,sensor-type + + "^thermocouple@": + type: object + description: + Represents a thermocouple sensor which is connected to one of the device + channels. + + properties: + adi,sensor-type: + description: | + 1 - Type J Thermocouple + 2 - Type K Thermocouple + 3 - Type E Thermocouple + 4 - Type N Thermocouple + 5 - Type R Thermocouple + 6 - Type S Thermocouple + 7 - Type T Thermocouple + 8 - Type B Thermocouple + 9 - Custom Thermocouple + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 9 + + adi,single-ended: + description: + Boolean property which set's the thermocouple as single-ended. + type: boolean + + adi,sensor-oc-current-microamp: + description: + This property set's the pulsed current value applied during + open-circuit detect. + enum: [10, 100, 500, 1000] + + adi,cold-junction-handle: + description: + Phandle which points to a sensor object responsible for measuring + the thermocouple cold junction temperature. + $ref: "/schemas/types.yaml#/definitions/phandle" + + adi,custom-thermocouple: + description: + This is a table, where each entry should be a pair of + voltage(mv)-temperature(K). The entries must be given in nv and uK + so that, the original values must be multiplied by 1000000. For + more details look at table 69 and 70. + Note should be signed, but dtc doesn't currently maintain the + sign. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-matrix + items: + minItems: 3 + maxItems: 64 + items: + minItems: 2 + maxItems: 2 + + "^diode@": + type: object + description: + Represents a diode sensor which is connected to one of the device + channels. + + properties: + adi,sensor-type: + description: Identifies the sensor as a diode. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + const: 28 + + adi,single-ended: + description: Boolean property which set's the diode as single-ended. + type: boolean + + adi,three-conversion-cycles: + description: + Boolean property which set's three conversion cycles removing + parasitic resistance effects between the LTC2983 and the diode. + type: boolean + + adi,average-on: + description: + Boolean property which enables a running average of the diode + temperature reading. This reduces the noise when the diode is used + as a cold junction temperature element on an isothermal block + where temperatures change slowly. + type: boolean + + adi,excitation-current-microamp: + description: + This property controls the magnitude of the excitation current + applied to the diode. Depending on the number of conversions + cycles, this property will assume different predefined values on + each cycle. Just set the value of the first cycle (1l). + enum: [10, 20, 40, 80] + + adi,ideal-factor-value: + description: + This property sets the diode ideality factor. The real value must + be multiplied by 1000000 to remove the fractional part. For more + information look at table 20 of the datasheet. + $ref: /schemas/types.yaml#/definitions/uint32 + + "^rtd@": + type: object + description: + Represents a rtd sensor which is connected to one of the device channels. + + properties: + reg: + minimum: 2 + maximum: 20 + + adi,sensor-type: + description: | + 10 - RTD PT-10 + 11 - RTD PT-50 + 12 - RTD PT-100 + 13 - RTD PT-200 + 14 - RTD PT-500 + 15 - RTD PT-1000 + 16 - RTD PT-1000 (0.00375) + 17 - RTD NI-120 + 18 - RTD Custom + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 10 + maximum: 18 + + adi,rsense-handle: + description: + Phandle pointing to a rsense object associated with this RTD. + $ref: "/schemas/types.yaml#/definitions/phandle" + + adi,number-of-wires: + description: + Identifies the number of wires used by the RTD. Setting this + property to 5 means 4 wires with Kelvin Rsense. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [2, 3, 4, 5] + + adi,rsense-share: + description: + Boolean property which enables Rsense sharing, where one sense + resistor is used for multiple 2-, 3-, and/or 4-wire RTDs. + type: boolean + + adi,current-rotate: + description: + Boolean property which enables excitation current rotation to + automatically remove parasitic thermocouple effects. Note that + this property is not allowed for 2- and 3-wire RTDs. + type: boolean + + adi,excitation-current-microamp: + description: + This property controls the magnitude of the excitation current + applied to the RTD. + enum: [5, 10, 25, 50, 100, 250, 500, 1000] + + adi,rtd-curve: + description: + This property set the RTD curve used and the corresponding + Callendar-VanDusen constants. Look at table 30 of the datasheet. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 0 + maximum: 3 + + adi,custom-rtd: + description: + This is a table, where each entry should be a pair of + resistance(ohm)-temperature(K). The entries added here are in uohm + and uK. For more details values look at table 74 and 75. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-matrix + items: + minItems: 3 + maxItems: 64 + items: + minItems: 2 + maxItems: 2 + + required: + - adi,rsense-handle + + dependencies: + adi,current-rotate: [ adi,rsense-share ] + + "^thermistor@": + type: object + description: + Represents a thermistor sensor which is connected to one of the device + channels. + + properties: + adi,sensor-type: + description: + 19 - Thermistor 44004/44033 2.252kohm at 25°C + 20 - Thermistor 44005/44030 3kohm at 25°C + 21 - Thermistor 44007/44034 5kohm at 25°C + 22 - Thermistor 44006/44031 10kohm at 25°C + 23 - Thermistor 44008/44032 30kohm at 25°C + 24 - Thermistor YSI 400 2.252kohm at 25°C + 25 - Thermistor Spectrum 1003k 1kohm + 26 - Thermistor Custom Steinhart-Hart + 27 - Custom Thermistor + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 19 + maximum: 27 + + adi,rsense-handle: + description: + Phandle pointing to a rsense object associated with this + thermistor. + $ref: "/schemas/types.yaml#/definitions/phandle" + + adi,single-ended: + description: + Boolean property which set's the thermistor as single-ended. + type: boolean + + adi,rsense-share: + description: + Boolean property which enables Rsense sharing, where one sense + resistor is used for multiple thermistors. Note that this property + is ignored if adi,single-ended is set. + type: boolean + + adi,current-rotate: + description: + Boolean property which enables excitation current rotation to + automatically remove parasitic thermocouple effects. + type: boolean + + adi,excitation-current-nanoamp: + description: + This property controls the magnitude of the excitation current + applied to the thermistor. Value 0 set's the sensor in auto-range + mode. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [0, 250, 500, 1000, 5000, 10000, 25000, 50000, 100000, + 250000, 500000, 1000000] + + adi,custom-thermistor: + description: + This is a table, where each entry should be a pair of + resistance(ohm)-temperature(K). The entries added here are in uohm + and uK only for custom thermistors. For more details look at table + 78 and 79. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64-matrix + items: + minItems: 3 + maxItems: 64 + items: + minItems: 2 + maxItems: 2 + + adi,custom-steinhart: + description: + Steinhart-Hart coefficients are also supported and can + be programmed into the device memory using this property. For + Steinhart sensors the coefficients are given in the raw + format. Look at table 82 for more information. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + items: + minItems: 6 + maxItems: 6 + + required: + - adi,rsense-handle + + dependencies: + adi,current-rotate: [ adi,rsense-share ] + + "^adc@": + type: object + description: Represents a channel which is being used as a direct adc. + + properties: + adi,sensor-type: + description: Identifies the sensor as a direct adc. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + const: 30 + + adi,single-ended: + description: Boolean property which set's the adc as single-ended. + type: boolean + + "^rsense@": + type: object + description: + Represents a rsense which is connected to one of the device channels. + Rsense are used by thermistors and RTD's. + + properties: + reg: + minimum: 2 + maximum: 20 + + adi,sensor-type: + description: Identifies the sensor as a rsense. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + const: 29 + + adi,rsense-val-milli-ohms: + description: + Sets the value of the sense resistor. Look at table 20 of the + datasheet for information. + + required: + - adi,rsense-val-milli-ohms + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + spi { + #address-cells = <1>; + #size-cells = <0>; + + sensor_ltc2983: ltc2983@0 { + compatible = "adi,ltc2983"; + reg = <0>; + + #address-cells = <1>; + #size-cells = <0>; + + interrupts = <20 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&gpio>; + + thermocouple@18 { + reg = <18>; + adi,sensor-type = <8>; //Type B + adi,sensor-oc-current-microamp = <10>; + adi,cold-junction-handle = <&diode5>; + }; + + diode5: diode@5 { + reg = <5>; + adi,sensor-type = <28>; + }; + + rsense2: rsense@2 { + reg = <2>; + adi,sensor-type = <29>; + adi,rsense-val-milli-ohms = <1200000>; //1.2Kohms + }; + + rtd@14 { + reg = <14>; + adi,sensor-type = <15>; //PT1000 + /*2-wire, internal gnd, no current rotation*/ + adi,number-of-wires = <2>; + adi,rsense-share; + adi,excitation-current-microamp = <500>; + adi,rsense-handle = <&rsense2>; + }; + + adc@10 { + reg = <10>; + adi,sensor-type = <30>; + adi,single-ended; + }; + + thermistor@12 { + reg = <12>; + adi,sensor-type = <26>; //Steinhart + adi,rsense-handle = <&rsense2>; + adi,custom-steinhart = <0x00F371EC 0x12345678 + 0x2C0F8733 0x10018C66 0xA0FEACCD + 0x90021D99>; //6 entries + }; + + thermocouple@20 { + reg = <20>; + adi,sensor-type = <9>; //custom thermocouple + adi,single-ended; + adi,custom-thermocouple = /bits/ 64 + <(-50220000) 0 + (-30200000) 99100000 + (-5300000) 135400000 + 0 273150000 + 40200000 361200000 + 55300000 522100000 + 88300000 720300000 + 132200000 811200000 + 188700000 922500000 + 460400000 1000000000>; //10 pairs + }; + + }; + }; +... |