diff options
Diffstat (limited to 'Documentation/isdn/INTERFACE.fax')
| -rw-r--r-- | Documentation/isdn/INTERFACE.fax | 163 |
1 files changed, 0 insertions, 163 deletions
diff --git a/Documentation/isdn/INTERFACE.fax b/Documentation/isdn/INTERFACE.fax deleted file mode 100644 index 9c8c6d914ec7..000000000000 --- a/Documentation/isdn/INTERFACE.fax +++ /dev/null @@ -1,163 +0,0 @@ -$Id: INTERFACE.fax,v 1.2 2000/08/06 09:22:50 armin Exp $ - - -Description of the fax-subinterface between linklevel and hardwarelevel of - isdn4linux. - - The communication between linklevel (LL) and hardwarelevel (HL) for fax - is based on the struct T30_s (defined in isdnif.h). - This struct is allocated in the LL. - In order to use fax, the LL provides the pointer to this struct with the - command ISDN_CMD_SETL3 (parm.fax). This pointer expires in case of hangup - and when a new channel to a new connection is assigned. - - -Data handling: - In send-mode the HL-driver has to handle the <DLE> codes and the bit-order - conversion by itself. - In receive-mode the LL-driver takes care of the bit-order conversion - (specified by +FBOR) - -Structure T30_s description: - - This structure stores the values (set by AT-commands), the remote- - capability-values and the command-codes between LL and HL. - - If the HL-driver receives ISDN_CMD_FAXCMD, all needed information - is in this struct set by the LL. - To signal information to the LL, the HL-driver has to set the - parameters and use ISDN_STAT_FAXIND. - (Please refer to INTERFACE) - -Structure T30_s: - - All members are 8-bit unsigned (__u8) - - - resolution - - rate - - width - - length - - compression - - ecm - - binary - - scantime - - id[] - Local faxmachine's parameters, set by +FDIS, +FDCS, +FLID, ... - - - r_resolution - - r_rate - - r_width - - r_length - - r_compression - - r_ecm - - r_binary - - r_scantime - - r_id[] - Remote faxmachine's parameters. To be set by HL-driver. - - - phase - Defines the actual state of fax connection. Set by HL or LL - depending on progress and type of connection. - If the phase changes because of an AT command, the LL driver - changes this value. Otherwise the HL-driver takes care of it, but - only necessary on call establishment (from IDLE to PHASE_A). - (one of the constants ISDN_FAX_PHASE_[IDLE,A,B,C,D,E]) - - - direction - Defines outgoing/send or incoming/receive connection. - (ISDN_TTY_FAX_CONN_[IN,OUT]) - - - code - Commands from LL to HL; possible constants : - ISDN_TTY_FAX_DR signals +FDR command to HL - - ISDN_TTY_FAX_DT signals +FDT command to HL - - ISDN_TTY_FAX_ET signals +FET command to HL - - - Other than that the "code" is set with the hangup-code value at - the end of connection for the +FHNG message. - - - r_code - Commands from HL to LL; possible constants : - ISDN_TTY_FAX_CFR output of +FCFR message. - - ISDN_TTY_FAX_RID output of remote ID set in r_id[] - (+FCSI/+FTSI on send/receive) - - ISDN_TTY_FAX_DCS output of +FDCS and CONNECT message, - switching to phase C. - - ISDN_TTY_FAX_ET signals end of data, - switching to phase D. - - ISDN_TTY_FAX_FCON signals the established, outgoing connection, - switching to phase B. - - ISDN_TTY_FAX_FCON_I signals the established, incoming connection, - switching to phase B. - - ISDN_TTY_FAX_DIS output of +FDIS message and values. - - ISDN_TTY_FAX_SENT signals that all data has been sent - and <DLE><ETX> is acknowledged, - OK message will be sent. - - ISDN_TTY_FAX_PTS signals a msg-confirmation (page sent successful), - depending on fet value: - 0: output OK message (more pages follow) - 1: switching to phase B (next document) - - ISDN_TTY_FAX_TRAIN_OK output of +FDCS and OK message (for receive mode). - - ISDN_TTY_FAX_EOP signals end of data in receive mode, - switching to phase D. - - ISDN_TTY_FAX_HNG output of the +FHNG and value set by code and - OK message, switching to phase E. - - - - badlin - Value of +FBADLIN - - - badmul - Value of +FBADMUL - - - bor - Value of +FBOR - - - fet - Value of +FET command in send-mode. - Set by HL in receive-mode for +FET message. - - - pollid[] - ID-string, set by +FCIG - - - cq - Value of +FCQ - - - cr - Value of +FCR - - - ctcrty - Value of +FCTCRTY - - - minsp - Value of +FMINSP - - - phcto - Value of +FPHCTO - - - rel - Value of +FREL - - - nbc - Value of +FNBC (0,1) - (+FNBC is not a known class 2 fax command, I added this to change the - automatic "best capabilities" connection in the eicon HL-driver) - - -Armin -mac@melware.de - |