summaryrefslogtreecommitdiffstats
path: root/Documentation/powerpc/booting-without-of.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/powerpc/booting-without-of.txt')
-rw-r--r--Documentation/powerpc/booting-without-of.txt189
1 files changed, 113 insertions, 76 deletions
diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index aee243a846a2..ea1b70b35793 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -89,10 +89,12 @@ Table of Contents
3) OpenPIC Interrupt Controllers
4) ISA Interrupt Controllers
- VIII - Specifying GPIO information for devices
+ IX - Specifying GPIO information for devices
1) gpios property
2) gpio-controller nodes
+ X - Specifying device power management information (sleep property)
+
Appendix A - Sample SOC node for MPC8540
@@ -2488,8 +2490,8 @@ encodings listed below:
2 = high to low edge sensitive type enabled
3 = low to high edge sensitive type enabled
-VIII - Specifying GPIO information for devices
-==============================================
+IX - Specifying GPIO information for devices
+============================================
1) gpios property
-----------------
@@ -2537,116 +2539,151 @@ Example of two SOC GPIO banks defined as gpio-controller nodes:
gpio-controller;
};
+X - Specifying Device Power Management Information (sleep property)
+===================================================================
+
+Devices on SOCs often have mechanisms for placing devices into low-power
+states that are decoupled from the devices' own register blocks. Sometimes,
+this information is more complicated than a cell-index property can
+reasonably describe. Thus, each device controlled in such a manner
+may contain a "sleep" property which describes these connections.
+
+The sleep property consists of one or more sleep resources, each of
+which consists of a phandle to a sleep controller, followed by a
+controller-specific sleep specifier of zero or more cells.
+
+The semantics of what type of low power modes are possible are defined
+by the sleep controller. Some examples of the types of low power modes
+that may be supported are:
+
+ - Dynamic: The device may be disabled or enabled at any time.
+ - System Suspend: The device may request to be disabled or remain
+ awake during system suspend, but will not be disabled until then.
+ - Permanent: The device is disabled permanently (until the next hard
+ reset).
+
+Some devices may share a clock domain with each other, such that they should
+only be suspended when none of the devices are in use. Where reasonable,
+such nodes should be placed on a virtual bus, where the bus has the sleep
+property. If the clock domain is shared among devices that cannot be
+reasonably grouped in this manner, then create a virtual sleep controller
+(similar to an interrupt nexus, except that defining a standardized
+sleep-map should wait until its necessity is demonstrated).
+
Appendix A - Sample SOC node for MPC8540
========================================
-Note that the #address-cells and #size-cells for the SoC node
-in this example have been explicitly listed; these are likely
-not necessary as they are usually the same as the root node.
-
- soc8540@e0000000 {
+ soc@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
- #interrupt-cells = <2>;
+ compatible = "fsl,mpc8540-ccsr", "simple-bus";
device_type = "soc";
- ranges = <00000000 e0000000 00100000>
- reg = <e0000000 00003000>;
+ ranges = <0x00000000 0xe0000000 0x00100000>
bus-frequency = <0>;
-
- mdio@24520 {
- reg = <24520 20>;
- device_type = "mdio";
- compatible = "gianfar";
-
- ethernet-phy@0 {
- linux,phandle = <2452000>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <0>;
- device_type = "ethernet-phy";
- };
-
- ethernet-phy@1 {
- linux,phandle = <2452001>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <1>;
- device_type = "ethernet-phy";
- };
-
- ethernet-phy@3 {
- linux,phandle = <2452002>
- interrupt-parent = <40000>;
- interrupts = <35 1>;
- reg = <3>;
- device_type = "ethernet-phy";
- };
-
- };
+ interrupt-parent = <&pic>;
ethernet@24000 {
- #size-cells = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
device_type = "network";
model = "TSEC";
- compatible = "gianfar";
- reg = <24000 1000>;
- mac-address = [ 00 E0 0C 00 73 00 ];
- interrupts = <d 3 e 3 12 3>;
- interrupt-parent = <40000>;
- phy-handle = <2452000>;
+ compatible = "gianfar", "simple-bus";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 E0 0C 00 73 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ phy-handle = <&phy0>;
+ sleep = <&pmc 00000080>;
+ ranges;
+
+ mdio@24520 {
+ reg = <0x24520 0x20>;
+ compatible = "fsl,gianfar-mdio";
+
+ phy0: ethernet-phy@0 {
+ interrupts = <5 1>;
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+
+ phy1: ethernet-phy@1 {
+ interrupts = <5 1>;
+ reg = <1>;
+ device_type = "ethernet-phy";
+ };
+
+ phy3: ethernet-phy@3 {
+ interrupts = <7 1>;
+ reg = <3>;
+ device_type = "ethernet-phy";
+ };
+ };
};
ethernet@25000 {
- #address-cells = <1>;
- #size-cells = <0>;
device_type = "network";
model = "TSEC";
compatible = "gianfar";
- reg = <25000 1000>;
- mac-address = [ 00 E0 0C 00 73 01 ];
- interrupts = <13 3 14 3 18 3>;
- interrupt-parent = <40000>;
- phy-handle = <2452001>;
+ reg = <0x25000 0x1000>;
+ local-mac-address = [ 00 E0 0C 00 73 01 ];
+ interrupts = <13 2 14 2 18 2>;
+ phy-handle = <&phy1>;
+ sleep = <&pmc 00000040>;
};
ethernet@26000 {
- #address-cells = <1>;
- #size-cells = <0>;
device_type = "network";
model = "FEC";
compatible = "gianfar";
- reg = <26000 1000>;
- mac-address = [ 00 E0 0C 00 73 02 ];
- interrupts = <19 3>;
- interrupt-parent = <40000>;
- phy-handle = <2452002>;
+ reg = <0x26000 0x1000>;
+ local-mac-address = [ 00 E0 0C 00 73 02 ];
+ interrupts = <41 2>;
+ phy-handle = <&phy3>;
+ sleep = <&pmc 00000020>;
};
serial@4500 {
- device_type = "serial";
- compatible = "ns16550";
- reg = <4500 100>;
- clock-frequency = <0>;
- interrupts = <1a 3>;
- interrupt-parent = <40000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fsl,mpc8540-duart", "simple-bus";
+ sleep = <&pmc 00000002>;
+ ranges;
+
+ serial@4500 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4500 0x100>;
+ clock-frequency = <0>;
+ interrupts = <42 2>;
+ };
+
+ serial@4600 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0x4600 0x100>;
+ clock-frequency = <0>;
+ interrupts = <42 2>;
+ };
};
- pic@40000 {
- linux,phandle = <40000>;
+ pic: pic@40000 {
interrupt-controller;
#address-cells = <0>;
- reg = <40000 40000>;
+ #interrupt-cells = <2>;
+ reg = <0x40000 0x40000>;
compatible = "chrp,open-pic";
device_type = "open-pic";
};
i2c@3000 {
- interrupt-parent = <40000>;
- interrupts = <1b 3>;
- reg = <3000 18>;
- device_type = "i2c";
+ interrupts = <43 2>;
+ reg = <0x3000 0x100>;
compatible = "fsl-i2c";
dfsrr;
+ sleep = <&pmc 00000004>;
};
+ pmc: power@e0070 {
+ compatible = "fsl,mpc8540-pmc", "fsl,mpc8548-pmc";
+ reg = <0xe0070 0x20>;
+ };
};
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-19 01:47:43 +0000