diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 7 | ||||
| -rw-r--r-- | Documentation/hwmon/w83627hf | 4 | ||||
| -rw-r--r-- | Documentation/hwmon/w83781d | 24 | ||||
| -rw-r--r-- | Documentation/i2c/busses/i2c-piix4 | 2 | ||||
| -rw-r--r-- | Documentation/i2c/busses/scx200_acb | 5 | ||||
| -rw-r--r-- | Documentation/kernel-parameters.txt | 4 | ||||
| -rw-r--r-- | Documentation/networking/pktgen.txt | 20 |
7 files changed, 55 insertions, 11 deletions
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index afeaf6218ea2..c7a4d0faab22 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -158,13 +158,6 @@ Who: Adrian Bunk <bunk@stusta.de> --------------------------- -What: Legacy /proc/pci interface (PCI_LEGACY_PROC) -When: March 2006 -Why: deprecated since 2.5.53 in favor of lspci(8) -Who: Adrian Bunk <bunk@stusta.de> - ---------------------------- - What: pci_module_init(driver) When: January 2007 Why: Is replaced by pci_register_driver(pci_driver). diff --git a/Documentation/hwmon/w83627hf b/Documentation/hwmon/w83627hf index bbeaba680443..792231921241 100644 --- a/Documentation/hwmon/w83627hf +++ b/Documentation/hwmon/w83627hf @@ -18,6 +18,10 @@ Supported chips: Prefix: 'w83637hf' Addresses scanned: ISA address retrieved from Super I/O registers Datasheet: http://www.winbond.com/PDF/sheet/w83637hf.pdf + * Winbond W83687THF + Prefix: 'w83687thf' + Addresses scanned: ISA address retrieved from Super I/O registers + Datasheet: Provided by Winbond on request Authors: Frodo Looijaard <frodol@dds.nl>, diff --git a/Documentation/hwmon/w83781d b/Documentation/hwmon/w83781d index e5459333ba68..b1e9f80098ee 100644 --- a/Documentation/hwmon/w83781d +++ b/Documentation/hwmon/w83781d @@ -36,6 +36,11 @@ Module parameters Use 'init=0' to bypass initializing the chip. Try this if your computer crashes when you load the module. +* reset int + (default 0) + The driver used to reset the chip on load, but does no more. Use + 'reset=1' to restore the old behavior. Report if you need to do this. + force_subclients=bus,caddr,saddr,saddr This is used to force the i2c addresses for subclients of a certain chip. Typical usage is `force_subclients=0,0x2d,0x4a,0x4b' @@ -123,6 +128,25 @@ When an alarm goes off, you can be warned by a beeping signal through your computer speaker. It is possible to enable all beeping globally, or only the beeping for some alarms. +Individual alarm and beep bits: + +0x000001: in0 +0x000002: in1 +0x000004: in2 +0x000008: in3 +0x000010: temp1 +0x000020: temp2 (+temp3 on W83781D) +0x000040: fan1 +0x000080: fan2 +0x000100: in4 +0x000200: in5 +0x000400: in6 +0x000800: fan3 +0x001000: chassis +0x002000: temp3 (W83782D and W83627HF only) +0x010000: in7 (W83782D and W83627HF only) +0x020000: in8 (W83782D and W83627HF only) + If an alarm triggers, it will remain triggered until the hardware register is read at least once. This means that the cause for the alarm may already have disappeared! Note that in the current implementation, all diff --git a/Documentation/i2c/busses/i2c-piix4 b/Documentation/i2c/busses/i2c-piix4 index 856b4b8b962c..a1c8f581afed 100644 --- a/Documentation/i2c/busses/i2c-piix4 +++ b/Documentation/i2c/busses/i2c-piix4 @@ -4,7 +4,7 @@ Supported adapters: * Intel 82371AB PIIX4 and PIIX4E * Intel 82443MX (440MX) Datasheet: Publicly available at the Intel website - * ServerWorks OSB4, CSB5 and CSB6 southbridges + * ServerWorks OSB4, CSB5, CSB6 and HT-1000 southbridges Datasheet: Only available via NDA from ServerWorks * Standard Microsystems (SMSC) SLC90E66 (Victory66) southbridge Datasheet: Publicly available at the SMSC website http://www.smsc.com diff --git a/Documentation/i2c/busses/scx200_acb b/Documentation/i2c/busses/scx200_acb index 08c8cd1df60c..f50e69981ec6 100644 --- a/Documentation/i2c/busses/scx200_acb +++ b/Documentation/i2c/busses/scx200_acb @@ -6,9 +6,10 @@ Module Parameters ----------------- * base: int - Base addresses for the ACCESS.bus controllers + Base addresses for the ACCESS.bus controllers on SCx200 and SC1100 devices Description ----------- -Enable the use of the ACCESS.bus controllers of a SCx200 processor. +Enable the use of the ACCESS.bus controller on the Geode SCx200 and +SC1100 processors and the CS5535 and CS5536 Geode companion devices. diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 7b7382d0f758..44a25f3f51d1 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -49,6 +49,7 @@ restrictions referred to are that the relevant option is valid if: MCA MCA bus support is enabled. MDA MDA console support is enabled. MOUSE Appropriate mouse support is enabled. + MSI Message Signaled Interrupts (PCI). MTD MTD support is enabled. NET Appropriate network support is enabled. NUMA NUMA support is enabled. @@ -1152,6 +1153,9 @@ running once the system is up. Mechanism 2. nommconf [IA-32,X86_64] Disable use of MMCONFIG for PCI Configuration + nomsi [MSI] If the PCI_MSI kernel config parameter is + enabled, this kernel boot option can be used to + disable the use of MSI interrupts system-wide. nosort [IA-32] Don't sort PCI devices according to order given by the PCI BIOS. This sorting is done to get a device order compatible with diff --git a/Documentation/networking/pktgen.txt b/Documentation/networking/pktgen.txt index cc4b4d04129c..278771c9ad99 100644 --- a/Documentation/networking/pktgen.txt +++ b/Documentation/networking/pktgen.txt @@ -109,6 +109,22 @@ Examples: cycle through the port range. pgset "udp_dst_max 9" set UDP destination port max. + pgset "mpls 0001000a,0002000a,0000000a" set MPLS labels (in this example + outer label=16,middle label=32, + inner label=0 (IPv4 NULL)) Note that + there must be no spaces between the + arguments. Leading zeros are required. + Do not set the bottom of stack bit, + thats done automatically. If you do + set the bottom of stack bit, that + indicates that you want to randomly + generate that address and the flag + MPLS_RND will be turned on. You + can have any mix of random and fixed + labels in the label stack. + + pgset "mpls 0" turn off mpls (or any invalid argument works too!) + pgset stop aborts injection. Also, ^C aborts generator. @@ -167,6 +183,8 @@ pkt_size min_pkt_size max_pkt_size +mpls + udp_src_min udp_src_max @@ -211,4 +229,4 @@ Grant Grundler for testing on IA-64 and parisc, Harald Welte, Lennert Buytenhek Stephen Hemminger, Andi Kleen, Dave Miller and many others. -Good luck with the linux net-development.
\ No newline at end of file +Good luck with the linux net-development. |