diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt | 75 | ||||
| -rw-r--r-- | Documentation/networking/batman-adv.txt | 7 | ||||
| -rw-r--r-- | Documentation/networking/ip-sysctl.txt | 37 | ||||
| -rw-r--r-- | Documentation/networking/stmmac.txt | 5 |
4 files changed, 107 insertions, 17 deletions
diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt new file mode 100644 index 000000000000..8516929c7251 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -0,0 +1,75 @@ +Properties for an MDIO bus multiplexer controlled by a memory-mapped device + +This is a special case of a MDIO bus multiplexer. A memory-mapped device, +like an FPGA, is used to control which child bus is connected. The mdio-mux +node must be a child of the memory-mapped device. The driver currently only +supports devices with eight-bit registers. + +Required properties in addition to the generic multiplexer properties: + +- compatible : string, must contain "mdio-mux-mmioreg" + +- reg : integer, contains the offset of the register that controls the bus + multiplexer. The size field in the 'reg' property is the size of + register, and must therefore be 1. + +- mux-mask : integer, contains an eight-bit mask that specifies which + bits in the register control the actual bus multiplexer. The + 'reg' property of each child mdio-mux node must be constrained by + this mask. + +Example: + +The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes. +For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus. +A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on +BRDCFG1 that control the actual mux. + + /* The FPGA node */ + fpga: board-control@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + ranges = <0 3 0 0x30>; + + mdio-mux-emi2 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&xmdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <9 1>; // BRDCFG1 + mux-mask = <0x6>; // EMI2 + + emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2) + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + + emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1) + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot2: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; + }; + }; + }; + + /* The parent MDIO bus. */ + xmdio0: mdio@f1000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <100 1 0 0>; + }; diff --git a/Documentation/networking/batman-adv.txt b/Documentation/networking/batman-adv.txt index 8f3ae4a6147e..a173d2a879f5 100644 --- a/Documentation/networking/batman-adv.txt +++ b/Documentation/networking/batman-adv.txt @@ -75,9 +75,10 @@ folder: There is a special folder for debugging information: -# ls /sys/kernel/debug/batman_adv/bat0/ -# bla_claim_table log socket transtable_local -# gateways originators transtable_global vis_data +# ls /sys/kernel/debug/batman_adv/bat0/ +# bla_backbone_table log transtable_global +# bla_claim_table originators transtable_local +# gateways socket vis_data Some of the files contain all sort of status information regard- ing the mesh network. For example, you can view the table of diff --git a/Documentation/networking/ip-sysctl.txt b/Documentation/networking/ip-sysctl.txt index ca447b35b833..c7fc10724948 100644 --- a/Documentation/networking/ip-sysctl.txt +++ b/Documentation/networking/ip-sysctl.txt @@ -439,7 +439,9 @@ tcp_stdurg - BOOLEAN tcp_synack_retries - INTEGER Number of times SYNACKs for a passive TCP connection attempt will be retransmitted. Should not be higher than 255. Default value - is 5, which corresponds to ~180seconds. + is 5, which corresponds to 31seconds till the last retransmission + with the current initial RTO of 1second. With this the final timeout + for a passive TCP connection will happen after 63seconds. tcp_syncookies - BOOLEAN Only valid when the kernel was compiled with CONFIG_SYNCOOKIES @@ -465,20 +467,37 @@ tcp_syncookies - BOOLEAN tcp_fastopen - INTEGER Enable TCP Fast Open feature (draft-ietf-tcpm-fastopen) to send data in the opening SYN packet. To use this feature, the client application - must not use connect(). Instead, it should use sendmsg() or sendto() - with MSG_FASTOPEN flag which performs a TCP handshake automatically. - - The values (bitmap) are: - 1: Enables sending data in the opening SYN on the client - 5: Enables sending data in the opening SYN on the client regardless - of cookie availability. + must use sendmsg() or sendto() with MSG_FASTOPEN flag rather than + connect() to perform a TCP handshake automatically. + + The values (bitmap) are + 1: Enables sending data in the opening SYN on the client. + 2: Enables TCP Fast Open on the server side, i.e., allowing data in + a SYN packet to be accepted and passed to the application before + 3-way hand shake finishes. + 4: Send data in the opening SYN regardless of cookie availability and + without a cookie option. + 0x100: Accept SYN data w/o validating the cookie. + 0x200: Accept data-in-SYN w/o any cookie option present. + 0x400/0x800: Enable Fast Open on all listeners regardless of the + TCP_FASTOPEN socket option. The two different flags designate two + different ways of setting max_qlen without the TCP_FASTOPEN socket + option. Default: 0 + Note that the client & server side Fast Open flags (1 and 2 + respectively) must be also enabled before the rest of flags can take + effect. + + See include/net/tcp.h and the code for more details. + tcp_syn_retries - INTEGER Number of times initial SYNs for an active TCP connection attempt will be retransmitted. Should not be higher than 255. Default value - is 5, which corresponds to ~180seconds. + is 6, which corresponds to 63seconds till the last restransmission + with the current initial RTO of 1second. With this the final timeout + for an active TCP connection attempt will happen after 127seconds. tcp_timestamps - BOOLEAN Enable timestamps as defined in RFC1323. diff --git a/Documentation/networking/stmmac.txt b/Documentation/networking/stmmac.txt index c676b9cedbd0..ef9ee71b4d7f 100644 --- a/Documentation/networking/stmmac.txt +++ b/Documentation/networking/stmmac.txt @@ -173,7 +173,6 @@ Where: For MDIO bus The we have: struct stmmac_mdio_bus_data { - int bus_id; int (*phy_reset)(void *priv); unsigned int phy_mask; int *irqs; @@ -181,7 +180,6 @@ For MDIO bus The we have: }; Where: - o bus_id: bus identifier; o phy_reset: hook to reset the phy device attached to the bus. o phy_mask: phy mask passed when register the MDIO bus within the driver. o irqs: list of IRQs, one per PHY. @@ -230,9 +228,6 @@ there are two MAC cores: one MAC is for MDIO Bus/PHY emulation with fixed_link support. static struct stmmac_mdio_bus_data stmmac1_mdio_bus = { - .bus_id = 1, - | - |-> phy device on the bus_id 1 .phy_reset = phy_reset; | |-> function to provide the phy_reset on this board |