diff options
Diffstat (limited to 'Documentation')
3 files changed, 71 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt new file mode 100644 index 000000000000..f7cc7c060910 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt @@ -0,0 +1,35 @@ +* Atmel SAMA5D4 Watchdog Timer (WDT) Controller + +Required properties: +- compatible: "atmel,sama5d4-wdt" +- reg: base physical address and length of memory mapped region. + +Optional properties: +- timeout-sec: watchdog timeout value (in seconds). +- interrupts: interrupt number to the CPU. +- atmel,watchdog-type: should be "hardware" or "software". + "hardware": enable watchdog fault reset. A watchdog fault triggers + watchdog reset. + "software": enable watchdog fault interrupt. A watchdog fault asserts + watchdog interrupt. +- atmel,idle-halt: present if you want to stop the watchdog when the CPU is + in idle state. + CAUTION: This property should be used with care, it actually makes the + watchdog not counting when the CPU is in idle state, therefore the + watchdog reset time depends on mean CPU usage and will not reset at all + if the CPU stop working while it is in idle state, which is probably + not what you want. +- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is + in debug state. + +Example: + watchdog@fc068640 { + compatible = "atmel,sama5d4-wdt"; + reg = <0xfc068640 0x10>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH 5>; + timeout-sec = <10>; + atmel,watchdog-type = "hardware"; + atmel,dbg-halt; + atmel,idle-halt; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt b/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt new file mode 100644 index 000000000000..09f6b24969e0 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt @@ -0,0 +1,19 @@ +* NXP LPC18xx Watchdog Timer (WDT) + +Required properties: +- compatible: Should be "nxp,lpc1850-wwdt" +- reg: Should contain WDT registers location and length +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Should contain "wdtclk" and "reg"; the watchdog counter + clock and register interface clock respectively. +- interrupts: Should contain WDT interrupt + +Examples: + +watchdog@40080000 { + compatible = "nxp,lpc1850-wwdt"; + reg = <0x40080000 0x24>; + clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>; + clock-names = "wdtclk", "reg"; + interrupts = <49>; +}; diff --git a/Documentation/watchdog/src/watchdog-test.c b/Documentation/watchdog/src/watchdog-test.c index 3da822967ee0..fcdde8fc98be 100644 --- a/Documentation/watchdog/src/watchdog-test.c +++ b/Documentation/watchdog/src/watchdog-test.c @@ -41,6 +41,7 @@ static void term(int sig) int main(int argc, char *argv[]) { int flags; + unsigned int ping_rate = 1; fd = open("/dev/watchdog", O_WRONLY); @@ -63,22 +64,33 @@ int main(int argc, char *argv[]) fprintf(stderr, "Watchdog card enabled.\n"); fflush(stderr); goto end; + } else if (!strncasecmp(argv[1], "-t", 2) && argv[2]) { + flags = atoi(argv[2]); + ioctl(fd, WDIOC_SETTIMEOUT, &flags); + fprintf(stderr, "Watchdog timeout set to %u seconds.\n", flags); + fflush(stderr); + goto end; + } else if (!strncasecmp(argv[1], "-p", 2) && argv[2]) { + ping_rate = strtoul(argv[2], NULL, 0); + fprintf(stderr, "Watchdog ping rate set to %u seconds.\n", ping_rate); + fflush(stderr); } else { - fprintf(stderr, "-d to disable, -e to enable.\n"); + fprintf(stderr, "-d to disable, -e to enable, -t <n> to set " \ + "the timeout,\n-p <n> to set the ping rate, and \n"); fprintf(stderr, "run by itself to tick the card.\n"); fflush(stderr); goto end; } - } else { - fprintf(stderr, "Watchdog Ticking Away!\n"); - fflush(stderr); } + fprintf(stderr, "Watchdog Ticking Away!\n"); + fflush(stderr); + signal(SIGINT, term); while(1) { keep_alive(); - sleep(1); + sleep(ping_rate); } end: close(fd); |