diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-usb | 7 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/am33xx-usb.txt | 14 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci13xxx-imx.txt | 5 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/omap-usb.txt | 33 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/platform-uhci.txt | 12 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/pxa-usb.txt | 31 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/twlxxxx-usb.txt | 40 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/usb-phy.txt | 17 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/usbmisc-imx.txt | 14 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/vt8500-ehci.txt | 12 | ||||
| -rw-r--r-- | Documentation/feature-removal-schedule.txt | 11 | ||||
| -rw-r--r-- | Documentation/usb/persist.txt | 3 |
12 files changed, 188 insertions, 11 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb index 5f75f8f7df34..b6fbe514a869 100644 --- a/Documentation/ABI/testing/sysfs-bus-usb +++ b/Documentation/ABI/testing/sysfs-bus-usb @@ -220,3 +220,10 @@ Description: If the device doesn't support LTM, the file will read "no". The file will be present for all speeds of USB devices, and will always read "no" for USB 1.1 and USB 2.0 devices. + +What: /sys/bus/usb/devices/.../(hub interface)/portX +Date: August 2012 +Contact: Lan Tianyu <tianyu.lan@intel.com> +Description: + The /sys/bus/usb/devices/.../(hub interface)/portX + is usb port device's sysfs directory. diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt new file mode 100644 index 000000000000..ca8fa56e9f03 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -0,0 +1,14 @@ +AM33XX MUSB GLUE + - compatible : Should be "ti,musb-am33xx" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - port0_mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - port1_mode : Should be "1" to represent HOST. "3" signifies OTG and "2" + represents PERIPHERAL. + - power : Should be "250". This signifies the controller can supply upto + 500mA when operating in host mode. diff --git a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt index 2c290418bb2d..5778b9c83bd8 100644 --- a/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt +++ b/Documentation/devicetree/bindings/usb/ci13xxx-imx.txt @@ -7,7 +7,10 @@ Required properties: Optional properties: - fsl,usbphy: phandler of usb phy that connects to the only one port +- fsl,usbmisc: phandler of non-core register device, with one argument + that indicate usb controller index - vbus-supply: regulator for vbus +- disable-over-current: disable over current detect Examples: usb@02184000 { /* USB OTG */ @@ -15,4 +18,6 @@ usb@02184000 { /* USB OTG */ reg = <0x02184000 0x200>; interrupts = <0 43 0x04>; fsl,usbphy = <&usbphy1>; + fsl,usbmisc = <&usbmisc 0>; + disable-over-current; }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt new file mode 100644 index 000000000000..29a043ecda52 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -0,0 +1,33 @@ +OMAP GLUE + +OMAP MUSB GLUE + - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num_eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram_bits : Specifies the ram address size. Should be set to "12" + - interface_type : This is a board specific setting to describe the type of + interface between the controller and the phy. It should be "0" or "1" + specifying ULPI and UTMI respectively. + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - power : Should be "50". This signifies the controller can supply upto + 100mA when operating in host mode. + +SOC specific device node entry +usb_otg_hs: usb_otg_hs@4a0ab000 { + compatible = "ti,omap4-musb"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num_eps = <16>; + ram_bits = <12>; +}; + +Board specific device node entry +&usb_otg_hs { + interface_type = <1>; + mode = <3>; + power = <50>; +}; diff --git a/Documentation/devicetree/bindings/usb/platform-uhci.txt b/Documentation/devicetree/bindings/usb/platform-uhci.txt new file mode 100644 index 000000000000..91477d6830ec --- /dev/null +++ b/Documentation/devicetree/bindings/usb/platform-uhci.txt @@ -0,0 +1,12 @@ +Generic Platform UHCI controllers. + +Required properties: + - compatible: Should be "platform-uhci". + - reg: Address range of the uhci registers + - interrupts: Should contain the uhci interrupt. + +usb: uhci@D8007301 { + compatible = "platform-uhci", "usb-uhci"; + reg = <0xD8007301 0x200>; + interrupts = <0>; +}; diff --git a/Documentation/devicetree/bindings/usb/pxa-usb.txt b/Documentation/devicetree/bindings/usb/pxa-usb.txt new file mode 100644 index 000000000000..79729a948d5a --- /dev/null +++ b/Documentation/devicetree/bindings/usb/pxa-usb.txt @@ -0,0 +1,31 @@ +PXA USB controllers + +OHCI + +Required properties: + - compatible: Should be "marvell,pxa-ohci" for USB controllers + used in host mode. + +Optional properties: + - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3" + If present, enables the appropriate USB port of the controller. + - "marvell,port-mode" selects the mode of the ports: + 1 = PMM_NPS_MODE + 2 = PMM_GLOBAL_MODE + 3 = PMM_PERPORT_MODE + - "marvell,power-sense-low" - power sense pin is low-active. + - "marvell,power-control-low" - power control pin is low-active. + - "marvell,no-oc-protection" - disable over-current protection. + - "marvell,oc-mode-perport" - enable per-port over-current protection. + - "marvell,power_on_delay" Power On to Power Good time - in ms. + +Example: + + usb0: ohci@4c000000 { + compatible = "marvell,pxa-ohci", "usb-ohci"; + reg = <0x4c000000 0x100000>; + interrupts = <18>; + marvell,enable-port1; + marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */ + }; + diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt new file mode 100644 index 000000000000..36b9aede3f40 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -0,0 +1,40 @@ +USB COMPARATOR OF TWL CHIPS + +TWL6030 USB COMPARATOR + - compatible : Should be "ti,twl6030-usb" + - interrupts : Two interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts when + the controller has to act as host and the second interrupt number is the + usb interrupt number that raises VBUS interrupts when the controller has to + act as device + - usb-supply : phandle to the regulator device tree node. It should be vusb + if it is twl6030 or ldousb if it is twl6025 subclass. + +twl6030-usb { + compatible = "ti,twl6030-usb"; + interrupts = < 4 10 >; +}; + +Board specific device node entry +&twl6030-usb { + usb-supply = <&vusb>; +}; + +TWL4030 USB PHY AND COMPARATOR + - compatible : Should be "ti,twl4030-usb" + - interrupts : The interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts + and VBUS interrupts. The second interrupt number is optional. + - <supply-name>-supply : phandle to the regulator device tree node. + <supply-name> should be vusb1v5, vusb1v8 and vusb3v1 + - usb_mode : The mode used by the phy to connect to the controller. "1" + specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode. + +twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = < 10 4 >; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt new file mode 100644 index 000000000000..80d4148cb661 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-phy.txt @@ -0,0 +1,17 @@ +USB PHY + +OMAP USB2 PHY + +Required properties: + - compatible: Should be "ti,omap-usb2" + - reg : Address and length of the register set for the device. Also +add the address of control module dev conf register until a driver for +control module is added + +This is usually a subnode of ocp2scp to which it is connected. + +usb2phy@4a0ad080 { + compatible = "ti,omap-usb2"; + reg = <0x4a0ad080 0x58>, + <0x4a002300 0x4>; +}; diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt new file mode 100644 index 000000000000..97ce94e1a6cc --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -0,0 +1,14 @@ +* Freescale i.MX non-core registers + +Required properties: +- #index-cells: Cells used to descibe usb controller index. Should be <1> +- compatible: Should be one of below: + "fsl,imx6q-usbmisc" for imx6q +- reg: Should contain registers location and length + +Examples: +usbmisc@02184800 { + #index-cells = <1>; + compatible = "fsl,imx6q-usbmisc"; + reg = <0x02184800 0x200>; +}; diff --git a/Documentation/devicetree/bindings/usb/vt8500-ehci.txt b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt new file mode 100644 index 000000000000..5fb8fd6e250c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/vt8500-ehci.txt @@ -0,0 +1,12 @@ +VIA VT8500 and Wondermedia WM8xxx SoC USB controllers. + +Required properties: + - compatible: Should be "via,vt8500-ehci" or "wm,prizm-ehci". + - reg: Address range of the ehci registers. size should be 0x200 + - interrupts: Should contain the ehci interrupt. + +usb: ehci@D8007100 { + compatible = "wm,prizm-ehci", "usb-ehci"; + reg = <0xD8007100 0x200>; + interrupts = <1>; +}; diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt index bc55d38081dc..43975ba1fde1 100644 --- a/Documentation/feature-removal-schedule.txt +++ b/Documentation/feature-removal-schedule.txt @@ -463,17 +463,6 @@ Who: Bjorn Helgaas <bhelgaas@google.com> ---------------------------- -What: Low Performance USB Block driver ("CONFIG_BLK_DEV_UB") -When: 3.6 -Why: This driver provides support for USB storage devices like "USB - sticks". As of now, it is deactivated in Debian, Fedora and - Ubuntu. All current users can switch over to usb-storage - (CONFIG_USB_STORAGE) which only drawback is the additional SCSI - stack. -Who: Sebastian Andrzej Siewior <sebastian@breakpoint.cc> - ----------------------------- - What: get_robust_list syscall When: 2013 Why: There appear to be no production users of the get_robust_list syscall, diff --git a/Documentation/usb/persist.txt b/Documentation/usb/persist.txt index 074b159b77c2..35d70eda9ad6 100644 --- a/Documentation/usb/persist.txt +++ b/Documentation/usb/persist.txt @@ -155,6 +155,9 @@ If the kernel gets fooled in this way, it's almost certain to cause data corruption and to crash your system. You'll have no one to blame but yourself. +For those devices with avoid_reset_quirk attribute being set, persist +maybe fail because they may morph after reset. + YOU HAVE BEEN WARNED! USE AT YOUR OWN RISK! That having been said, most of the time there shouldn't be any trouble |