diff options
Diffstat (limited to 'Documentation')
17 files changed, 127 insertions, 78 deletions
diff --git a/Documentation/ABI/testing/sysfs-platform-twl4030-usb b/Documentation/ABI/testing/sysfs-platform-twl4030-usb new file mode 100644 index 000000000000..512c51be64ae --- /dev/null +++ b/Documentation/ABI/testing/sysfs-platform-twl4030-usb @@ -0,0 +1,8 @@ +What: /sys/bus/platform/devices/*twl4030-usb/vbus +Description: + Read-only status reporting if VBUS (approx 5V) + is being supplied by the USB bus. + + Possible values: "on", "off". + + Changes are notified via select/poll. diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt new file mode 100644 index 000000000000..7f81ef90146a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-sata-phy.txt @@ -0,0 +1,40 @@ +* Broadcom SATA3 PHY for STB + +Required properties: +- compatible: should be one or more of + "brcm,bcm7445-sata-phy" + "brcm,phy-sata3" +- address-cells: should be 1 +- size-cells: should be 0 +- reg: register range for the PHY PCB interface +- reg-names: should be "phy" + +Sub-nodes: + Each port's PHY should be represented as a sub-node. + +Sub-nodes required properties: +- reg: the PHY number +- phy-cells: generic PHY binding; must be 0 +Optional: +- brcm,enable-ssc: use spread spectrum clocking (SSC) on this port + + +Example: + + sata-phy@f0458100 { + compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; + reg = <0xf0458100 0x1e00>, <0xf045804c 0x10>; + reg-names = "phy"; + #address-cells = <1>; + #size-cells = <0>; + + sata-phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + sata-phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/pxa1928-usb-phy.txt b/Documentation/devicetree/bindings/phy/pxa1928-usb-phy.txt new file mode 100644 index 000000000000..660a13ca90b3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/pxa1928-usb-phy.txt @@ -0,0 +1,18 @@ +* Marvell PXA1928 USB and HSIC PHYs + +Required properties: +- compatible: "marvell,pxa1928-usb-phy" or "marvell,pxa1928-hsic-phy" +- reg: base address and length of the registers +- clocks - A single clock. From common clock binding. +- #phys-cells: should be 0. From commmon phy binding. +- resets: reference to the reset controller + +Example: + + usbphy: phy@7000 { + compatible = "marvell,pxa1928-usb-phy"; + reg = <0x7000 0xe0>; + clocks = <&apmu_clocks PXA1928_CLK_USB>; + #phy-cells = <0>; + }; + diff --git a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt index 00fc52a034b7..d564ba4f1cf6 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen2-phy.txt @@ -6,6 +6,7 @@ This file provides information on what the device node for the R-Car generation Required properties: - compatible: "renesas,usb-phy-r8a7790" if the device is a part of R8A7790 SoC. "renesas,usb-phy-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,usb-phy-r8a7794" if the device is a part of R8A7794 SoC. - reg: offset and length of the register block. - #address-cells: number of address cells for the USB channel subnodes, must be <1>. diff --git a/Documentation/devicetree/bindings/power/twl-charger.txt b/Documentation/devicetree/bindings/power/twl-charger.txt index d5c706216df5..3b4ea1b73b38 100644 --- a/Documentation/devicetree/bindings/power/twl-charger.txt +++ b/Documentation/devicetree/bindings/power/twl-charger.txt @@ -1,5 +1,15 @@ TWL BCI (Battery Charger Interface) +The battery charger needs to interact with the USB phy in order +to know when charging is permissible, and when there is a connection +or disconnection. + +The choice of phy cannot be configured at a hardware level, so there +is no value in explicit configuration in device-tree. Rather +if there is a sibling of the BCI node which is compatible with +"ti,twl4030-usb", then that is used to determine when and how +use USB power for charging. + Required properties: - compatible: - "ti,twl4030-bci" diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt deleted file mode 100644 index 38a548001e3a..000000000000 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-imx.txt +++ /dev/null @@ -1,35 +0,0 @@ -* Freescale i.MX ci13xxx usb controllers - -Required properties: -- compatible: Should be "fsl,imx27-usb" -- reg: Should contain registers location and length -- interrupts: Should contain controller interrupt -- fsl,usbphy: phandle of usb phy that connects to the port - -Recommended properies: -- phy_type: the type of the phy connected to the core. Should be one - of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this - property the PORTSC register won't be touched -- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" - -Optional properties: -- fsl,usbmisc: phandler of non-core register device, with one argument - that indicate usb controller index -- vbus-supply: regulator for vbus -- disable-over-current: disable over current detect -- external-vbus-divider: enables off-chip resistor divider for Vbus -- maximum-speed: limit the maximum connection speed to "full-speed". -- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts - -Examples: -usb@02184000 { /* USB OTG */ - compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; - reg = <0x02184000 0x200>; - interrupts = <0 43 0x04>; - fsl,usbphy = <&usbphy1>; - fsl,usbmisc = <&usbmisc 0>; - disable-over-current; - external-vbus-divider; - maximum-speed = "full-speed"; - tpl-support; -}; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt deleted file mode 100644 index f2899b550939..000000000000 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-qcom.txt +++ /dev/null @@ -1,17 +0,0 @@ -Qualcomm CI13xxx (Chipidea) USB controllers - -Required properties: -- compatible: should contain "qcom,ci-hdrc" -- reg: offset and length of the register set in the memory map -- interrupts: interrupt-specifier for the controller interrupt. -- usb-phy: phandle for the PHY device -- dr_mode: Should be "peripheral" - -Examples: - gadget@f9a55000 { - compatible = "qcom,ci-hdrc"; - reg = <0xf9a55000 0x400>; - dr_mode = "peripheral"; - interrupts = <0 134 0>; - usb-phy = <&usbphy0>; - }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 27f8b1e5ee46..553e2fae3a76 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -1,15 +1,35 @@ * USB2 ChipIdea USB controller for ci13xxx Required properties: -- compatible: should be "chipidea,usb2" +- compatible: should be one of: + "fsl,imx27-usb" + "lsi,zevio-usb" + "qcom,ci-hdrc" + "chipidea,usb2" - reg: base address and length of the registers - interrupts: interrupt for the USB controller +Recommended properies: +- phy_type: the type of the phy connected to the core. Should be one + of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this + property the PORTSC register won't be touched. +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +Deprecated properties: +- usb-phy: phandle for the PHY device. Use "phys" instead. +- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead. + Optional properties: - clocks: reference to the USB clock - phys: reference to the USB PHY - phy-names: should be "usb-phy" - vbus-supply: reference to the VBUS regulator +- maximum-speed: limit the maximum connection speed to "full-speed". +- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts +- fsl,usbmisc: (FSL only) phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: (FSL only) disable over current detect +- external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus Example: diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-zevio.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-zevio.txt deleted file mode 100644 index abbcb2aea38c..000000000000 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-zevio.txt +++ /dev/null @@ -1,17 +0,0 @@ -* LSI Zevio USB OTG Controller - -Required properties: -- compatible: Should be "lsi,zevio-usb" -- reg: Should contain registers location and length -- interrupts: Should contain controller interrupt - -Optional properties: -- vbus-supply: regulator for vbus - -Examples: - usb0: usb@b0000000 { - reg = <0xb0000000 0x1000>; - compatible = "lsi,zevio-usb"; - interrupts = <8>; - vbus-supply = <&vbus_reg>; - }; diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt index f9d70252bbb2..01c71b1258f4 100644 --- a/Documentation/devicetree/bindings/usb/dwc3-st.txt +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -49,8 +49,7 @@ st_dwc3: dwc3@8f94000 { st,syscfg = <&syscfg_core>; resets = <&powerdown STIH407_USB3_POWERDOWN>, <&softreset STIH407_MIPHY2_SOFTRESET>; - reset-names = "powerdown", - "softreset"; + reset-names = "powerdown", "softreset"; #address-cells = <1>; #size-cells = <1>; pinctrl-names = "default"; @@ -62,7 +61,7 @@ st_dwc3: dwc3@8f94000 { reg = <0x09900000 0x100000>; interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; dr_mode = "host"; - phys-names = "usb2-phy", "usb3-phy"; - phys = <&usb2_picophy2>, <&phy_port2 MIPHY_TYPE_USB>; + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>; }; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 5cc364309edb..0815eac5b185 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -38,6 +38,8 @@ Optional properties: - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold + - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for + UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. This is usually a subnode to DWC3 glue to which it is connected. diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index 2826f2af503a..bd8d9e753029 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -69,6 +69,17 @@ Optional properties: (no, min, max) where each value represents either a voltage in microvolts or a value corresponding to voltage corner. +- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy + and controller driver therefore enables pull-up explicitly + before starting controller using usbcmd run/stop bit. + +- extcon: phandles to external connector devices. First phandle + should point to external connector, which provide "USB" + cable events, the second should point to external connector + device, which provide "USB-HOST" cable events. If one of + the external connector devices is not required empty <0> + phandle should be specified. + Example HSUSB OTG controller device node: usb@f9a55000 { diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt index ddbe304beb21..64a4ca6cf96f 100644 --- a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Must contain one of the following: - "renesas,usbhs-r8a7790" - "renesas,usbhs-r8a7791" + - "renesas,usbhs-r8a7794" - reg: Base address and length of the register for the USBHS - interrupts: Interrupt specifier for the USBHS - clocks: A list of phandle + clock specifier pairs diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt index 0aee0ad3f035..17327a296110 100644 --- a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -30,6 +30,9 @@ TWL4030 USB PHY AND COMPARATOR - usb_mode : The mode used by the phy to connect to the controller. "1" specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode. +If a sibling node is compatible "ti,twl4030-bci", then it will find +this device and query it for USB power status. + twl4030-usb { compatible = "ti,twl4030-usb"; interrupts = < 10 4 >; diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt index 0b04fdff9d5a..a12d6012a40f 100644 --- a/Documentation/devicetree/bindings/usb/usb-ehci.txt +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -13,6 +13,8 @@ Optional properties: - big-endian-desc : boolean, set this for hcds with big-endian descriptors - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc - needs-reset-on-resume : boolean, set this to force EHCI reset after resume + - has-transaction-translator : boolean, set this if EHCI have a Transaction + Translator built into the root hub. - clocks : a list of phandle + clock specifier pairs - phys : phandle + phy specifier pair - phy-names : "usb" diff --git a/Documentation/phy.txt b/Documentation/phy.txt index 371361c69a4b..b388c5af9e72 100644 --- a/Documentation/phy.txt +++ b/Documentation/phy.txt @@ -76,6 +76,8 @@ struct phy *phy_get(struct device *dev, const char *string); struct phy *phy_optional_get(struct device *dev, const char *string); struct phy *devm_phy_get(struct device *dev, const char *string); struct phy *devm_phy_optional_get(struct device *dev, const char *string); +struct phy *devm_of_phy_get_by_index(struct device *dev, struct device_node *np, + int index); phy_get, phy_optional_get, devm_phy_get and devm_phy_optional_get can be used to get the PHY. In the case of dt boot, the string arguments @@ -86,7 +88,10 @@ successful PHY get. On driver detach, release function is invoked on the the devres data and devres data is freed. phy_optional_get and devm_phy_optional_get should be used when the phy is optional. These two functions will never return -ENODEV, but instead returns NULL when -the phy cannot be found. +the phy cannot be found.Some generic drivers, such as ehci, may use multiple +phys and for such drivers referencing phy(s) by name(s) does not make sense. In +this case, devm_of_phy_get_by_index can be used to get a phy reference based on +the index. It should be noted that NULL is a valid phy reference. All phy consumer calls on the NULL phy become NOPs. That is the release calls, diff --git a/Documentation/usb/gadget-testing.txt b/Documentation/usb/gadget-testing.txt index f45b2bf4b41d..592678009c15 100644 --- a/Documentation/usb/gadget-testing.txt +++ b/Documentation/usb/gadget-testing.txt @@ -526,8 +526,6 @@ Except for ifname they can be written to until the function is linked to a configuration. The ifname is read-only and contains the name of the interface which was assigned by the net core, e. g. usb0. -By default there can be only 1 RNDIS interface in the system. - Testing the RNDIS function -------------------------- @@ -629,7 +627,7 @@ Function-specific configfs interface The function name to use when creating the function directory is "uac2". The uac2 function provides these attributes in its function directory: - chmask - capture channel mask + c_chmask - capture channel mask c_srate - capture sampling rate c_ssize - capture sample size (bytes) p_chmask - playback channel mask |